Fibar Group FGR221 Operating Manual

OPERATING MANUAL

ROLLER SHUTTER CONTROLLER

FGR221 v1.4

ENG

Remotely controlled Roller Shutter Controller of FIBARO system is
designed to control motors of roller shutters, awnings, etc.

It has the function of detecting the current state of a controlled
device, e.g. position of roller shutter.

• Controlled by FIBARO system devices or any Z-Wave controller.

• Microprocessor control

• Executive elements: relays.

• The device may be operated by mono-stable and bi-stable
push-buttons and by push-buttons dedicated for roller shutters.

Specifications

Power supply

Power of supplied motor

In accordance with EU
standards

Temperature limits

Operational temperature

For installation in boxes

Radio protocol

Radio Frequency

Range

Dimensions (H x W x D)

110 - 230 V ±10% 50/60Hz

up to 1kW

EN 55022
EN 61000

105 °C

0 - 40 °C

Ø ≥ 50mm

Z-Wave

868 MHz

up to 50 m outdoors
up to 30 m indoors
(depending on building materials)

15 x 42 x 36 mm

Technical Information

FIBARO is a wireless system, based on Z-Wave technology.

FIBARO provides many advantages when compared to similar
systems. In general, radio systems create a direct connection

between the receiver and transmitter. But the radio signal is
weakened by various obstacles located on its path (apartment walls,
furniture, etc.) and in extreme cases it fails to transfer required data.

The advantage of FIBARO system is that its devices apart from

being transmitters and receivers of signals, they are also a signal
"duplicators". When a direct connection path between the transmitter
and the receiver can not be established, the connection may be

achieved through other intermediate devices.

FIBARO is a bi-directional wireless system. It means that the signal
is not only sent to the receivers but also the receivers send the

confirmation of its reception. This operation confirms their status so
to check whether they are active. Safety of the FIBARO system

transmission is comparable to the safety of transmission in data bus

wired systems.

FIBARO operates in the free band for data transmission at 868MHz

frequency. Every FIBARO system has its own unique identification

number (home ID). Therefore, it is possible to operate two or more
independent systems in one building without any interference.

Although Z-Wave is quite new technology, it has already become
recognizable and officially binding standard, similarly to Wi-Fi. Many
manufacturers in various industries offer solutions based on Z-Wave
technology, guaranteeing their compatibility. This means that the
system is open and it may be extended in the future. Find more
information at www.fibaro.com.

FIBARO generates a dynamic network structure. After FIBARO
system is switched on, the location of its individual components is

automatically updated in real-time through status confirmation

signals received from devices operating in a "mesh" network.

The in-wall Roller Shutter Controller is hereinafter referred to as
Fibaro Roller Controller. It is designed to switch rise/lower roller

shutter connected to its terminals using radio waves, controllers and

a push button directly connected to Fibaro Roller Controller.

1. Before installation ensure that the voltage supply is
disconnected.

2. Connect the Roller Shutter Controller in accordance with the
diagram on Fig. 1

3. Place the device in the electrical box.

4. Arrange the antenna (tips are presented below diagrams of
fig. 1)

Roller

Shutter

L N

S1 S2

O1

L

N

M

N

O2

B

Fig.1 Circuit diagrams for the Roller Shutter Controller

NOTES FOR THE DIAGRAM:

L - live lead
N - neutral lead
S1 - terminal for key no. 1 (has the option of entering the device in
self-learning mode)
S2 - terminal for key No. 2
O1 - output terminal no. 1 for shutter motor
O2 - output terminal no. 2 for shutter motor
B - service button (used to add or remove a device from the system)

Locate the antenna as far from metal elements as

possible (connecting wires, bracket rings, etc.) in

order to prevent interferences.

i

Metal surfaces in the direct vicinity of the antenna

(e.g. flush mounted metal boxes, metal door frames)

may impair signal reception!

i

Do not cut or shorten the antenna - its length is
perfectly matched to the band in which the system

operates

i

TIPS FOR ARRANGING THE ANTENNA:

Note!

It should be noted that the push-button connected to

S1 terminal operates with the shutter motor output

(O1), while the push-button connected to S2

terminal, operates with the shutter motor output O2.

Therefore, it has to be defined which connected
push-button causes the Roller Shutter to move up /

down.

i

Note!

It should be noted that only the push-button
connected to S1 terminal and service push-button B
enables "self-learning" mode (Include/ Exclude).

i

DICTIONARY:

• INCLUSION (Adding) - a device sends "Node Info" frame, to
enable user to add it to Fibaro system (Home Center)

• EXCLUSION (Removing) - removing a device from the Fibaro

radio system

• ASSOCIATION - controlling other devices of system Fibaro system

• MultiChannelAssociation - controlling other multichannel devices

of Fibaro system

III Starting the operation of the
Roller Shutter Controller

1. Installing the Roller Shutter Controller

STEP 1

Connect the device in accordance with the circuit diagram presented

in Figure 1. Switch on 230V of the mains voltage.

[Adding/ Removing] of the Roller Shutter Controller [to/ from]
Z-wave network

STEP 2

The Roller Shutter Controller must be placed within the range of

Home Center controller, as the adding mode requires direct
communication with the controller.

STEP 3
Identify key no. 1. If the device is connected in accordance with the
diagram shown in Figure 1, this will the key that raises the roller
shutter.

STEP 4

Set the controller in add/remove mode (see the controller's manual)

STEP 5

Add the Roller Shutter Controller to the network by pushing three
times (sat) key no. 1 or push-button B located inside the housing of

the device.

WARNING!
The Roller Shutter Controller cancels the "learning"
mode after key no. 1 is pressed once. Therefore,
pressing key no. 1 four times will not add the devices
to the network.

Raising / lowering the roller shutter is achieved by moving the slider
or by pressing the appropriate button, as shown in Figure 2.

i

WARNING!

The Roller Shutter Controller is set by default to
operate with mono-stable switches (i.e. single-pole
switch or bell switch). While adding the Roller
Shutter Controller to the network with bi-stable

switches, ensure that all switch contacts are open

(off), because closing them results in activating the
push-button and this will prevent adding the device

to the network.

i

During the installation, it is recommended to use a
mono-stable keys or push- button B.

STEP 6

The controller indicates that the device is correctly added to the
network, (see the manual of Home Center controller).

It should be noted that after proper adding the Roller Shutter
Controller to the Fibaro system, it should be calibrated. The
calibration process involves performing two complete cycles of
opening/ closing the shutter. Properly completed calibration may be
verified by setting required position of the shutter using the icon e.g.
30% of shutter opening - the actual opening should correspond to
this value/position.

2. Resetting the Roller Shutter Controller

The Roller Shutter Controller provides two methods for resetting.

Method I : Reset by removing the Roller Shutter Controller from the
existing Z-Wave network. The device may be removed using the
controller that has the ability to include/exclude devices from/to
Z-Wave network (see the manual of controller).

Method II : Within 5 sec. after connecting mains voltage supply, the
Roller Shutter Controller allows the user to reset settings by pressing

once S1 key and then holding key S2.

3. Controlling the Roller Shutter Controller by
mono-stable or bi-stable switches.

Mono-stable switch (after releasing the push-button a spring
automatically pushes back and disconnects the button )

- Raising / lowering the roller shutter - shortly press the button

assigned for the action.

Bi-stable switch (operates as a two-position switch, it has no
spring that would push back the device after releasing manual
pressure)

- Raising / lowering the roller shutter - change the position of selected
push-button from the current position.

4. Controlling the Roller Shutter Controller using

a command: ALL ON / ALL OFF

The Roller Shutter Controller responds to commands ALL ON / ALL
OFF that may be sent by the controller. ALL ON / ALL OFF
commands are usually implemented in Z-Wave remote control.

By default, the Roller Shutter Controller accepts both active
commands ALL ON and ALL OFF. Settings may be changed by

entering an appropriate value into configuration register no. 1

5. Controlling the Roller Shutter Controller using
Fibaro system controller

After adding the Roller Shutter Controller to the network, it will be

represented in Home Center by the following icon:

Fig. 2 The icon of the roller shutter shown on the Fibaro controller

IV Association

Association enables the Roller Shutter Controller to directly control
a device included in Z-Wave network e.g. Dimmer, Switch (ON-OFF)

or scene

WARNING!

Association ensures direct transfer of control

commands between devices, and is performed

without participation of the main controller.

i

The Roller Shutter Controller enables user to associate three
groups.

Group I is triggered by single-clicking of any key (does not work

when using bi-stable keys )

Group II is triggered by holding down any key

Group III for controllers such Home Center for state reporting

The Roller Shutter Controller enables user to control up to 16 normal

devices, and 7 MultiChannel devices in group no. 1 and no. 2, group

no. 3 has only one field. The first field in each group is reserved for

the network controller. It is recommended to use up to 10 devices, as

the time required by the device to send a command to each
associated device may be quite long.

To add an association (using Fibaro controller), go to device options

by clicking the following icon:

Select the "device options" tab. Then specify to which group and
what devices are to be associated. Sending relevant information to

devices added to associated groups may take even a few minutes

(see details in the controller's manual ).

WARNING!

When the Roller Shutter Controller sends control

commands and a new command is issued, then the
current one command transmission is interrupted to
send new commands.

WARNING!

Entering incorrect parameters may cause incorrect
operation of the Roller Shutter Controller.

i

i

FGR221 Roller Shutter Controller supports the operation of

multi-channel devices. Multichannel devices are devices that include

two or more circuits inside one physical unit.

The Roller Shutter Controller allows user to configure the following

parameters:

V Configuration

Parameter no. 1 - Activate / deactivate functions ALL ON / ALL

OFF. default value 0

Options for changing parameter 255, 0, 1, 2

Available configuration parameters:

255 - ALL ON active, ALL OFF active.
0 - ALL ON is not active ALL OFF is not active
1 - ALL ON is not active ALL OFF active
2 - ALL ON active ALL OFF is not active

Parameter no. 10 - Turning off the shutter positioning function

default value 0

Options for changing parameter 0, 1

0 - Turning on the shutter positioning function
1 - Turning off the shutter positioning function

Parameter no. 14 - Switch type connector, you may choose
between mono-stable and bi-stable switches default value 0

Options for changing parameter 0, 1, 2

0 - mono-stable switch
1 - bi-stable switch
2 - single mono-stable switch

Parameter no. 20 - Saving the position "Favourites"

default value 16

Options for changing parameter 1-99

Possibility to change the configuration of the following
parameters [30 - 33].

0 - DEACTIVATION - the device does not respond to alarm data

frames

1 - CLOSED SHUTTER ALARM - the device closes the roller shutter

after detecting an alarm

2 - OPEN SHUTTER ALARM - the device opens the roller shutter

after detecting an alarm

Parameter no. 30 - General Alarm, set for shutter no. 1

default value 1[byte] CLOSED SHUTTER ALARM

Parameter no. 31 - Alarm of flooding with water, set for relay the
shutter.

default value 0[byte] ALARM DEACTIVATION

Parameter no. 32 - Smoke, CO, CO2 Alarm. Set for the roller
shutter.

default value 1[byte] OPEN SHUTTER ALARM

Parameter no. 33 - Temperature Alarm, set for roller shutter

default value 1[byte] CLOSED SHUTTER ALARM

Operating alarm data frames

Fibaro system allows user to set response of devices to alarm
situations (response to data-frames ALARM_REPORT and
SENSOR_ALARM_REPORT) The Roller Shutter Controller
responds to the following alarm types:

• General Purpose Alarm - GENERAL PURPOSE ALARM [0x00]

• Smoke Alarm - ALARM CO2 [0x02], ALARM CO [0x01], ALARM
SMOKE [0x03]

• Water Flooding Alarm - ALARM WATER [0x05]

• Temperature Alarm - ALARM HEAT [0x04]

Alarm data-frames are sent by devices that are system sensors (e.g.,
flood sensors, smoke detectors, motion detectors, etc.).

The device may respond in the following manner to received

data-frames (settings are configured in configuration parameters,
see section V Configuration ):

• 0 - DEACTIVATION - the device does not respond to alarm data

frames

• 1 - OPEN SHUTTER ALARM - the device opens the roller shutter

after detecting an alarm

• 2 - CLOSED SHUTTER ALARM - the device closes the roller

shutter after detecting an alarm

Position indicating

The Roller Shutter Controller has built-in mechanisms enabling it to

detect the current position of roller shutters, awnings and similar
devices. For proper operation of the mechanism, it is necessary to
use a motor with mechanical limit switches. Correct operation of the
position detecting mechanism, when using motor with overload

switches, depends on motor power and the suitability of specific
models - therefore it is recommended to use a motor with mechanical
limit switches. For each engine type the calibration procedure should
be performed.

VI Additional Functionality

VII Operating the Shutter Roller Controller

The Roller Shutter Controller may be operated using the
following control elements:

- any controller compatible with the system

- a mobile phone (e.g. iPhone and phones from other manufacturers
with appropriate software)

- devices of tablet type (such as iPad)

- PC, using a web browser

- using a push-button connected to the device

DANGER

Danger of electrocution! All works on the device

may be performed only by a qualified and licensed
electrician. Observe national regulations.

DANGER

Danger of electrocution. Even when the device is

turned off, voltage may be present at its terminals.

Any works introducing changes into the

configuration of connections or the load must be

always performed with disconnected voltage

(disable the fuse).

TIPS

• Do not connect the device to loads exceeding

recommended values.

• Connect only in accordance with the diagram
presented in the manual. Improper connections may

be dangerous.

i

I GENERAL INFORMATION ABOUT FIBARO SYSTEM

II Assembling Roller Shutter Controller

Danger of electrocution.

The device does not respond to a pre-programmed transmitter:

• Make sure that the maximum range is not exceeded and the signal
path is not obstructed by metal surfaces such as metal cabinets, etc.

• Make sure the device is not in the programming mode, or repeat

the programming process.

VIII Procedures for malfunctions

IX GUARANTEE

1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.
(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421
Poznan, entered in the register of the National Court Register kept
by the District Court in Poznań, VIII Economic Department of the
National Court Register, no. 370151, NIP 7811858097, REGON:

301595664.

2. The Manufacturer is responsible for equipment malfunction
resulting from physical defects (manufacturing or material) of the

Device for 12 months from the date of its purchasing.

3. The guarantee is valid exclusively in Europe.

4. During the Guarantee period, the Manufacturer shall remove any

defects, free of charge, by repairing or replacing (at the sole
discretion of the Manufacturer) any defective components of the

Device with new or regenerated components, that are free of

defects. When the repair impossible, the Manufacturer reserves the

right to replace the device with a new or regenerated one, which shall

be free of any defects and its condition shall not be worse than the
original device owned by the Customer.

5. In special cases, when the device cannot be replaced with the
device of the same type (e.g. the device is no longer available in the
commercial offer), the Manufacturer may replace it with a different

device having technical parameters similar to the faulty one. Such

activity shall be considered as fulfilling the obligations of the

Manufacturer. The Manufacturer shall not refund money paid for the
device.

6. The holder of a valid guarantee shall submit a guarantee claim
through the guarantee service. Remember: before you submit a

guarantee claim, contact or technical support using telephone or

e-mail. More than 50% of operational problems is resolved remotely,

saving time and money spent to initiating guarantee procedure. If
remote support is insufficient, the Customer shall fill the guarantee

claim form (using our website - www.fibargroup.com) in order to
obtain claim authorization.
When the guarantee claim form is submitted correctly, the Customer
shall receive the claim confirmation with an unique number (Return
Merchandise Authorization -RMA).

7. The claim may be also submitted by telephone. In this case, the
call is recorded and the Customer shall be informed about it by a
consultant before submitting he claim. Immediately after submitting

the claim, the consultant shall provide the Customer with the claim

number (RMA-number).

8. When the guarantee claim form is submitted correctly, a

representative of the Authorised Guarantee Service (hereinafter as

"AGS") shall contact the Customer to agree the date and place of site
visit, during which the technicians will examine the operation of the

device in the presence of the customer.

9. Defects revealed within the guarantee period shall be removed
not later than 30 days from the date of delivering the Device to AGS.
The guarantee period shall be extended by the time in which the
Device was kept by AGS.

10. The faulty device shall be provided by the Customer with

complete standard equipment and documents proving its purchase.

11. Parts replaced under the guarantee are the property of the
Manufacturer. The guarantee for all parts replaced in the guarantee

process shall be equal to the guarantee period of the original device.
The guarantee period of the replaced part shall not be extended.

12. Travel expenses or costs of delivering the faulty device shall be
borne by the Manufacturer. For unjustified service calls, the Service
may charge the Customer with travel expenses and handling costs

related to the case.

13. AGS shall not accept a complaint claim only when:

• the Device was misused or the manual was not observed,

• the Device was provided by the Customer incomplete, without

accessories or nameplate,

• it was determined that the fault was caused by other reasons than

a material or manufacturing defect of the Device

• the guarantee document is not valid or there is no proof of

purchase,

14. The Manufacturer shall not be liable for damages to property
caused by defective device. The Manufacturer shall not be liable for

indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,

loss of benefits, claims by third parties and any property damage or
personal injuries arising from or related to the use of the Device.

15. The guarantee shall not cover:

• mechanical damages (cracks, fractures, cuts, abrasions, physical
deformations caused by impact, falling or dropping the device or
other object, improper use or not observing the operating manual);

• damages resulting from external causes, e.g.: flood, storm, fire,
lightning, natural disasters, earthquakes, war, civil disturbance, force
majeure, unforeseen accidents, theft, water damage, liquid leakage,
battery spill, weather conditions, sunlight, sand, moisture, high or low
temperature, air pollution;

• damages caused by malfunctioning software, attack of a computer
virus, or by failure to update the software as recommended by the
Manufacturer;

• damages resulting from: surges in the power and/or telecommuni-

cation network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other

devices not recommended by the Manufacturer.

• damages caused by operating or storing the device in extremely
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;

• damages caused by using accessories not recommended by the

Manufacturer

• damages caused by faulty electrical installation of the Customer,
including the use of incorrect fuses;

• damages caused by Customer's failure to provide maintenance and
servicing activities defined in the operating manual;

• damages resulting from the use of spurious spare parts or

accessories improper for given model, repairing and introducing

alterations by unauthorized persons;

• defects caused by operating faulty Device or accessories.

16. The scope of the guarantee repairs shall not include periodic
maintenance and inspections, in particular cleaning, adjustments,

operational checks, correction of errors or parameter programming

and other activities that should be performed by the user (Buyer).

The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.

17. If a defect is not covered by the guarantee, the Manufacturer

reserves the right to remove such defect at its sole discretion,
repairing the damaged or destroyed parts or providing components
necessary for repair or replacement.

18. This guarantee shall not exclude, limit or suspend the Customer

rights when the provided product is inconsistent with the purchase
agreement.

This Device may be used with all devices
certified with Z-Wave certificate and should be
compatible with such devices produced by
other manufacturers.

Any device compatible with Z-Wave may be added
to Fibaro system.

i

FIBARGROUP

FIBARO

In case of any technical questions contact customer service centre
in your country.

www.fibargroup.com