Fibar FGBS-001-EN-A-v1.1 OPERATING MANUAL

ENG

OPERATING MANUAL

UNIVERSAL BINARY SENSOR

FGBS-001-EN-A-v1.1

The Universal Binary Sensor is a wireless module that makes it
possible to improve the functionality of any sensor with a binary
output by allowing it to communicate with the wireless network
Z-WAVE and the FIBARO building intelligence system. Moreover,
the module allows for wireless communication between the system
and the DS18B20 temperature sensors. The device can service up
to two binary sensors and up to four DS18B20 temperature sensors.
The Sensor was designed for installation in the housing of a sensor
or another device, the functionality of which we wish to improve.

The Universal Binary Sensor may be used whenever wireless
collection of data from sensors is required. Once additional safety
housing have been installed, the Sensor can also be used in areas
with high humidity and high temperature. The Sensor’s main function
is the integration of the wireless Fibaro System with the existing
wire-based and wireless alarm and measurement systems. As an
element of the safety system the device is transparent for parametric
alarm lines.

Technical data

Supply voltage:

Input:

Output:

Maximum current carrying
capacity of outputs:

Maximum voltage at output
contacts:

Operating temperature:

Number of servicing
temperature sensors:

Measurement range:

In accordance with EU
standards:

Radio signal power:

Radio protocol:

Radio frequency:

Range:

Dimensions (L x W x H):

9-30V DC ±10%

2 potential-free inputs, 1 digital
input 1-wire

2 potential-free outputs

150mA

36V DC / 24V AC ±5%

0 - 40 °C

4

-55oC - +126oC

RoHS 2011/65/EU
RED 2014/53/EU

1mW

Z-Wave

868,4 MHz EU;
908,4 MHz US;
921,4 MHz ANZ;
869,2 MHz RU;

up to 30 m indoors (depending
on the construction materials)
up to 50m outdoors

27,3 x 14,5 x 12 mm

Technical information

• Controlled with FIBARO system devices or any Z-Wave controller

• Microprocessor-based control

• Compatible with regular and parametric alarm lines (can be

connected to 2 alarm detectors)

• Compatible with binary sensors (can be connected to 2 binary

outputs)

• Compatible with DS18B20 temperature sensors (can be connected

to four DS18B20 temperature sensors)

• In order to connect the DS18B20 sensors it is recommended to use

conductors made from a single wire with a length of up to 30 meters

DANGER

The Sensor is powered with secure voltage;
nevertheless, the user should be extra careful or
should commission the installation to a qualified
person.

Hint

The outputs of the device should not be loaded with
a current value exceeding 150mA

i

Hint

Connections should be made specifically
according to the diagrams presented in this

i

manual. Incorrect connection may lead to hazards.

I GENERAL INFORMATION ON THE FIBARO SYSTEM

Fibaro is a system that does not require any additional conductors;
it is based on the Z-Wave technology. Fibaro offers a wide array of
advantages in comparison to other, similar systems. In general,
radio-based systems establish a direct connection between the
receiver and the transmitter. The radio signal is attenuated by every
obstacle along its path (in the household e.g. walls, furniture, etc.).
In the worst case the radio system ceases to function. The
advantage of the Fibaro System is the fact that the devices act not
only as a signal receiver and transmitter, but also as a signal
“repeater”. If a direct radio link between the transmitter and the
receiver cannot be established, the connection will be carried out
with the use of other devices participating in communication.

Fibaro is a bidirectional wireless system. This means that the signal
is not only sent to the receivers, but also the receivers send
feedback confirming the reception of the signal. This also confirms
the condition of receivers, which allows us to check whether or not
a device has actually been switched on. The safety of transmission
of the Fibaro System is comparable with a wire-linked bus system.

Fibaro operates in the free band for data transmission. The
frequency depends on radio regulations in individual country . Each
Fibaro network has its own unique network identification number
(home ID), which is why it is possible to co-operate two or more
independent systems in a single building without any interference.

Although the Z-Wave technology is fairly new, it has already been
accepted as an official standard, just like Wi-Fi. Numerous
manufacturers from various fields offer solutions based on Z-Wave
technology, which are compatible with one another. This makes the
system fit for the future and allows for further development. For
more information go to www.fibaro.com.

Fibaro establishes a dynamic network structure. From the moment
of start-up, the location data of respective devices of the Fibaro
System is updated automatically, in real time, by confirming their
condition in the working „mesh” network.

II. Sensor Installation

1. Before the installation make sure to switch off the alarm
system, or any other system to which the device is to be
connected.

2. Connect the Fibaro Sensor according to the diagram.

3. Place the Fibaro Sensor in the sensor housing.

4. Arrange the antenna (instructions can be found below the
diagrams).

EXPLANATION OF
CONDUCTOR MARKINGS:

P – (POWER) – power supply conductor, red
GND - (GROUND) – ground conductor, blue
IN1 – input no. 1
IN2 – input no. 2
TP – (TEMP_POWER) – power supply conductor of the DS18B20
temperature sensor, brown (3.3V)
TD – (TEMP_DATA) – signal conductor of the DS18B20
temperature sensor, white
ANT – antenna, black
OUT1 – output no. 1 assigned to input IN1
OUT2 – output no. 2 assigned to input IN2
B – maintenance button (used to add devices to and remove
devices from the system)

ANTENNA ARRANGEMENT INSTRUCTIONS:

Lay down the antenna as far as possible from
metal elements (connection conductors, ring
brackets etc.), in order to prevent any interference

i

of the radio signal.

Metal surfaces in close vicinity (e.g. metal
embedded boxes, metal door trims) may impair the
reception capability!

i

You should not cut off or shorten the antenna. Its
length is suited ideally to the band at which the
system functions.

i

ANT

GND

TD

TP

IN2

IN1

B

GND

P

IN2 IN1 GND

NCNC

TMP TMP CO M 12V AUX COM Z1 Z2

P

MOTION DETECTOR

Diagram 1 – General

B

SYSTEM HUB

Diagram 2 – Connection to a regular alarm line

R1

R2

IN2 IN1 GND

NC NC TMP TMP COM 12V AUXCOM COM Z1

P

MOTION DETECTOR

B

ALARM

SYSTEM HUB

Diagram 3 – Connection to a parametric alarm line

Diagram 4 – Connection to DS18B20 sensors

}
}

ALARM

OUT 2

OUT 1

IN2

IN1

P

NO

GND

BELL-PUSH

NC NC

PRECIPITATION

SENSOR

Diagram 5 – example connection to a precipitation sensor

Note!

Do not remove the protective layer surrounding the
module. Make sure that no metal parts of other

i

devices or conductors come into close contact with
the installed Sensor.

Note!

Condition of outputs OUT1 and OUT2 is dependent
only on the condition of corresponding inputs,

i

irrespective of parameter settings or addition of
device to the Z-wave network.

Note!

Only the B button starts the device’s programming
process (Include/Exclude).

i

INSTRUCTIONS FOR ARRANGEMENT
OF THE DS18B20 SENSOR:

The DS18B20 sensor may easily be installed wherever very precise
temperature measurements are required. Moreover, if proper
protective measures are undertaken, the sensor may be used in
humid environments or under water, it may be embedded in
concrete or placed under the floor.

GLOSSARY OF TERMS:

• INCLUSION – the device sends out a Node Info frame, which

makes it possible to add it to the Fibaro system (Home Center)

• EXCLUSION – removal of device from the Fibaro system

• ASSOCIATION – controlling other devices of the Fibaro system

• MultiChannel Association - controlling other multi-channel

devices of the Fibaro system

III Fibaro Sensor start-up

1. Installation of the Universal Binary Sensor
Module

STEP 1

Connect the device according to the wiring diagram shown in figure

1. Engage the supply voltage.
[Inclusion / Exclusion] of the Fibaro Sensor [to / from] the Z-Wave
network

STEP 2

The Fibaro Module must be in range of the Home Center 2
controller, because the procedure of inclusion to the Fibaro system
requires direct communication with the controller.

STEP 3

Recognition of B button, which allows for proper inclusion of device.

STEP 4

Setting the Home Center 2 controller to the inclusion or exclusion
mode (see: Home Center 2 controller instructions).

STEP 5

The Fibaro Sensor is added to the network by quickly pressing the
B button three times (the button is located in the center of the
device).

STEP 6

Correct inclusion of the device to the network will be signaled by
Home Center 2 (see: Home Center 2 central hub operation
instructions).

2. Resetting the Fibaro Sensor

There are two procedures you can follow in order to reset the
Fibaro Sensor.

Method I
Resetting in the course of the procedure of excluding the Fibaro
Module from an existing Z-wave network. Devices may be excluded
with the use of a controller, which offers the option to exclude
devices from or include devices to the Z-wave network (see:
controller instructions).

Method II
Resetting by cutting off the power supply and re-connecting the
power supply while holding down the B button – after 10 seconds,
after another cut-off and re-connection of power supply the settings
of the device will be reset.

3. Controlling the Fibaro Sensor with the Home
Center 2 controller

The FGBS221 Sensor is a multi-channel device. This means that it
is equipped with two independent input circuits and a 1-wire bus
allowing it to be connected to four DS18B20 temperature sensors.
As a result, each device connected to the Sensor is represented by
an independent icon in the system.

After the Fibaro Sensor has been added to the network, it shall be
represented by appropriate icons in the Home Center 2 controller,
depending on the number of connected devices (3 – 7 icons).

In the event of including the Sensor without any sensors connected
(or with sensors connected only to IN1 and IN2), the device will be
represented by three icons. If DS18B20 sensors are also
connected, the devices will be represented by additional
temperature icons.

B

+9 - 30V

GND

Note!

Do not connect other sensors than DS18B20 to the
1-wire line (terminals TP and TD).

i

Note!

Every time when any changes are made to the
configuration of TP and TD lines (1-wire), e.g. when

i

DS18B20 sensor(s) is (are) included/excluded, it is
necessary to execute the procedure of exclusion
and repeated inclusion of the sensor module to the
central hub. It should be remembered that the
system shall enter into the programming mode only
once all the connected sensors have been
detected (about 10 s).

Note!

It is prohibited to connect the TP and TD lines to
devices that are not compatible with the 1-wire

i

protocol. Unused lines should be left insulated.

Fig. 1 - Fibaro Sensor icon in the Home Center controller

Note!

If the number of temperature sensor icons is
different than the actual number of sensors

i

connected to the device, or if the temperature
readings are incorrect, you should inspect the
connections on the 1-wire bus, in particular the
connection between respective sensor outputs and
the line and the total length of the bus (bus bar),
which should not exceed 30m.

IV Association

Association allows the Fibaro Sensor to directly control another
device of the Z-wave network, e.g. Dimmer, Switch (ON-OFF),
Roller Shutter or scenes (scene control is only possible via the
Home Center 2 controller).

NOTE!

Association allows for direct transmission of control
commands between devices and takes place

i

without the participation of the main controller.
Owing to this mechanism the Sensor may
communicate with devices even if the central
control hub is completely destroyed, e.g. in the
event of a fire.

The Fibaro Sensor makes it possible to configure three
association groups.

Group I is assigned to input IN1

Group II is assigned to input IN2

Group III reports on the condition of the device, only one device
may be assigned to the group.

The Fibaro Sensor allows for control over 5 regular devices and 5
multi-channel devices per group, out of which 1 field is reserved for
the network controller.

In order to add an association (with the use of the Home Center 2

controller) go to device options by clicking this icon:

Select the “device options” tab. Next, specify which devices will be
associated and with which groups. Sending of changed
configuration to the device might take couple of seconds.

V Configuration

The Universal Binary Sensor offers a wide range of advanced
settings, the parameters listed below are available in the
Fibaro configuration interface.

In order to configure the Fibaro Sensor (using the Home Center 2

controller) go to the device options by clicking on the icon:
Next, select the “device options” tab.

Device parameters:

Parameter No. 1

Input I alarm cancellation delay. Additional delay after an alarm
from input IN1 has ceased. The parameter allows you to specify
additional time, after which the input no. 1 alarm is cancelled once
its violation has ceased.

Default value: 0
Possible parameter settings: 0 – 65535 s
Parameter 2 [byte]

Parameter No. 2

Input II alarm cancellation delay. Additional delay after an alarm
from input IN2 has ceased. The parameter allows you to specify
additional time, after which the input no. 2 alarm is cancelled once
its violation has ceased.

Default value: 0
Possible parameter settings: 0 – 65535 s
Parameter 2 [byte]

Parameter No. 3

Type of input no. 1:
Default value: 1 – INPUT_NC (Normal Close) Possible parameter
settings:
0 – INPUT_NO (Normal Open)
1 – INPUT_NC (Normal Close)
2 – INPUT_MONOSTABLE
3 – INPUT_BISTABLE

Parameter No. 4

Type of input no. 2:
Default value: 1 - INPUT_NC (Normal Close)
Possible parameter settings:
0 – INPUT_NO (Normal Open)
1 – INPUT_NC (Normal Close)
2 – INPUT_MONOSTABLE
3 – INPUT_BISTABLE

Parameter No. 5

Type of transmitted control frame for association group 1, activated
via input IN1. The parameter allows to specify the type of alarm
frame or to force transmission of control commands (BASIC_SET)
Default value: 255 – BASIC SET

Possible parameter settings:
0 – Frame ALARM GENERIC
1 – Frame ALARM SMOKE
2 – Frame ALARM CO
3 – Frame ALARM CO2
4 – Frame ALARM HEAT
5 – Frame ALARM WATER
255 – Control frame BASIC_SET

Parameter No. 6

Type of transmitted control frame for association group 2, activated
via input IN2. The parameter allows to specify the type of alarm
frame or to force transmission of control commands (BASIC_SET)
Default value: 255 - BASIC SET

Possible parameter settings:
0 – Frame ALARM GENERIC
1 – Frame ALARM SMOKE
2 – Frame ALARM CO
3 – Frame ALARM CO2
4 – Frame ALARM HEAT
5 – Frame ALARM WATER
255 – Control frame BASIC_SET

Parameter No. 7

Value of the parameter specifying the forced level of dimming /
opening sun blinds when comes “switch on” / ”open” command to
devices from association group no. 1.
In the case of alarm frames the alarm priority is specified.
Default value: 255

Possible parameter settings: (1 – 99) and 255
Value of 255 makes it possible to activate the device when using
the Dimmer module it means activating the device and setting it to
the previous stored condition, e.g. when Dimmer is set to 30%, then
deactivated, and then reactivated using command 255, it will
automatically be set to the previous condition, i.e. 30%.

Parameter No. 8

Value of the parameter specifying the forced level of dimming /
opening sun blinds when comes “switch on” / ”open” command to
devices from association group no. 2.
In the case of alarm frames the alarm priority is specified.
Default value: 255

Possible parameter settings:
(1 – 99) and 255
Value of 255 makes it possible to activate the device; when using of
the Dimmer module it means activating the device and setting it to
the previous stored condition, e.g. when Dimmer is set to 30%, then
deactivated, and then reactivated using command 255, it will
automatically be set to the previous condition, i.e. 30%.

Parameter No. 9

Deactivating transmission of the frame cancelling the alarm or the
control frame deactivating the device (Basic). It allows for disabling
the deactivation function or the alarm cancellation function for
devices associated with the appropriate input of the Fibaro Sensor.
Default value: 0, in the case of association group no. 1 and 2 the
information is sent

Possible parameter settings:
0 – in the case of association group no. 1 and 2 the information is
sent
1 – in the case of association group no. 1 the information is sent. In
the case of association group no. 2 the information is not sent.
2 – in the case of association group no. 1 the information is not
sent. In the case of association group no. 2 the information is sent.
3 - for 1 and 2 association groups information is not sent.

NOTE: Information concerning alarm violation or activation
commands for devices from association groups are always
sent.

Parameter No. 10

Interval between successive readings of temperature from all
sensors connected to the device.
Default value: 20 s
Possible parameter settings:
1 – 255 s

Note: taking temperature readings from the sensor does not
result in sending a temperature condition report to the central
hub.

Parameter No. 11

Interval between forcing to send report concerning the temperature
conditions. The forced report is sent immediately after the next
reading of temperature from the sensor, irrespective of the settings
of parameter no. 12.
Default value: 200 s

Possible parameter settings:
0 – 255 s
0 – deactivating the function

Note: Frequent sending of temperature condition reports is
reasonable when the sensor is located somewhere where can
occure rapid changes of ambient temperature. In other cases
it is recommended to leave the parameter set to the default
value.

Parameter No. 12

Insensitiveness to temperature changes. This is the maximum
acceptable difference between the last reported temperature and
the current temperature taken from the sensor. If the temperatures
differ by the set value or more, then a report with the current
temperature value is sent to the device assigned to association
group no. 3. Intervals between taking readings from sensors are
specified by parameter no. 10.
Default value: 8 [0.5oC]

Possible parameter settings:0 – 255 [0oC to 16oC] [0 oF – 28.8oF]

In order to set the appropriate value of the parameter, the following
formula should be used:

x = delta T x 16 - for Celsius
x = delta T x 80 / 9 - for Fahrenheit

x – parameter value
delta T – maximum acceptable temperature gradient in Celsius or
Fahrenheit

If the value is set to 0, then information about the temperature will
be sent every time, immediately once the readings have been taken
from the sensor.

Parameter No. 13

Transmitting the alarm or control frame in “broadcast” mode (i.e. to
all devices within range), information sent in this mode is not
repeated by the mesh network.
Default value: 0

Possible parameter settings:
0 – IN1 and IN2 Broadcast inactive
1 – IN1 broadcast mode active, Sensor 2 broadcast mode inactive
2 – IN1 broadcast mode inactive, Sensor 2 broadcast mode active
3 – INI and IN2 broadcast mode active

NOTE!
If the “broadcast” mode of information transmission is
activated for a given channel, then transmission of
information in “singlecast” mode to devices assigned to the
association group of this channel is deactivated.

Parameter No. 14

Scene activation functionality.
Default value: 0

Possible parameter settings:
0 – deactivation of functionality
1 – activation of functionality

The device offers the possibility of sending commands compatible
with Command class scene activation. Information is sent to
devices assigned to association group no. 3.

Controllers such as Home Center 2 are able to interpret such
commands and basing on these commands they activate scenes,
to which specific scene IDs have been assigned. The user may
expand the functionality of the button connected to inputs IN1 and
IN2 by distinguishing the actions of keys connected to those inputs.
For example: double click would activate the scene “goodnight” and
triple click would activate the scene “morning”.

Scene ID is assigned in the following manner:
input IN1:
switch from “off” to “on” ID 10
switch from “on” to “off” ID 11

remaining IDs are recognized correctly if the value of parameter no.
3 was set to 2
holding down ID 12
releasing ID 13
double click ID 14
triple click ID 15

input IN2:
switch from “off” to “on” ID 20
switch from “on” to “off” ID 21
remaining IDs are recognized correctly if the value of parameter no.
4 was set to 2
holding down ID 22
releasing ID 23
double click ID 24
triple click ID 25

NOTE!!! Inputs IN1 and IN2 are used to control the condition of
the device. Each of them may force two conditions for
corresponding device channels: on / alarm, off / no alarm. If
monostable keys are used and the value of parameter no. 3 or
no. 4 is set to 2, change of the state of corresponding channel
will be able after a single click.

VI Additional functionality

Alarm frame servicing

The Fibaro system makes it possible to set the device’s reaction to
alarm events (reaction to the frame SENSOR_ALARM_REPORT).
The Fibaro Sensor transmits alarm frames of different types,
depending on the settings in parameters no. 5 and 6. The user
should correctly declare the type of alarm frame for each connected
sensor (inputs IN1 and IN2). For example, for a smoke detector
connected to input IN1 the user should declare the frame type 1 –
ALARM SMOKE (value of 1 should be entered), to ensure that the
remaining devices will correctly recognize information on smoke
detector alarm.

VII Sensor operation

The Fibaro Sensor may be operated with the following operator
elements:

• Any controller compatible with the system (e.g. Home Center 2
controller)

• Cellular phone (e.g. iPhone or phones of other manufacturers with
the proper control application)

• PC, with the use of an Internet browser

• Tablet devices (e.g. iPad)

• With the use of the maintenance button B located inside the
housing

VIII Procedure to be followed in the
case of interference

The Device does not react to a programmed transmitter:

• Make sure that the maximum range was not exceeded and that
there are no obstacles along the signal path which contain metal
surfaces, e.g. metal cabinets, ferroconcrete ceiling and load
bearing walls, etc.

• Make sure that the device is not in the programming mode.

• Possibly repeat the programming process.

XIX. GUARANTEE

1. FIBAR GROUP S.A. with its registered office in Poznan, ul.

Lotnicza 1, 60-421 Poznań, entered into the Register of

Entrepreneurs of the National Court Register maintained by the

District Court for Poznań-Nowe Miasto and Wilda in Poznań, VIII

Commercial Division of the National Court Register (KRS) under
number: 553265, NIP 7811858097, REGON: 301595664, share
capital PLN 1,182,100 paid in full, other contact information is
available at: www.fibaro.com (hereinafter "the Manufacturer")
guarantees that the device sold (hereinaftr: "the Device" is free from
material and manufacturing defects.

2. The Manufacturer shall be responsible for malfunctioning of the
Device resulting from physical defects inherent in the Device that
cause its operation to be incompatible with the specifications within
the period of:

- 24 months from the date of purchase by the consumer,

- 12 months from the date of purchase by a business customer (the
consumer and business customer are further collectively referred to
as "Customer").

3. The Manufacturer shall remove any defects revealed during the
guarantee period, free of charge, by repairing or replacing (at the
sole discretion of the Manufacturer) the defective components of the
Device with new or regenerated components. The manufacturer
reserves the right to replace the entire Device with a new or
regenerated device. The Manufacturer shall not refund money paid
for the device.

4. Under special circumstances, the Manufacturer may replace the
Device with a different device most similar in technical characteristics.

5. Only the holder of a valid guaranty document shall be entitled to
make claims under guarantee.

6. Before making a complaint, the Manufacturer recommends using
the telephone or online support available at https://www.fibaro.com/­support/.

7. In order to make a complaint, the Customer should contact the
Manufacturer via the email address given at https://www.fibaro.com/­support/.

8. After the complaint has been properly filed, the Customer will
receive contact details for the Authorized Guarantee Service
("AGS"). The customer should contact and deliver the Device to
AGS. Upon receipt of the Device, the manufacturer shall inform the
Customer of the return merchandise authorization number (RMA).

9. Defects shall be removed within 30 days from the date of
delivering the Device to AGS. The guarantee period shall be
extended by the time in which the Device was kept by AGS.

10. The faulty device shall be provided by the Customer with
complete standard equipment and documents proving its purchase.

11. The cost of transporting the Device in the territory of the Republic
of Poland shall be covered by the Manufacturer. The costs of the
Device transport from other countries shall be covered by the
Customer. For unjustified complaints, AGS may charge the
Customer with costs related to the case.

12. AGS shall not accept a complaint claim when:

- the Device was misused or the manual was not observed,

- the Device was provided by the Customer incomplete, without
accessories or nameplate,

- it was determined that the fault was caused by other reasons than
a material or manufacturing defect of the Device

- the guarantee document is not valid or there is no proof of
purchase,

13. The guarantee shall not cover:

- mechanical damages (cracks, fractures, cuts, abrasions, physical
deformations caused by impact, falling or dropping the device or
other object, improper use or not observing the operating manual);

- damages resulting from external causes, e.g.: flood, storm, fire,
lightning, natural disasters, earthquakes, war, civil disturbance, force
majeure, unforeseen accidents, theft, water damage, liquid leakage,
battery spill, weather conditions, sunlight, sand, moisture, high or low
temperature, air pollution;

- damages caused by malfunctioning software, attack of a computer
virus, or by failure to update the software as recommended by the
Manufacturer;

- damages resulting from: surges in the power and/or telecommuni­cation network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other
devices not recommended by the Manufacturer.

- damages caused by operating or storing the device in extremely
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;

- damages caused by using accessories not recommended by the
Manufacturer

- damages caused by faulty electrical installation of the Customer,
including the use of incorrect fuses;

- damages caused by Customer's failure to provide maintenance and
servicing activities defined in the operating manual;

- damages resulting from the use of spurious spare parts or
accessories improper for given model, repairing and introducing
alterations by unauthorized persons;

- defects caused by operating faulty Device or accessories.

14. The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.

15. The Device Guarantee shall not exclude, limit or suspend the
Customer's warranty rights.

16. The Manufacturer shall not be liable for damages to property
caused by defective device. The Guarantor shall not be liable for
indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,
loss of benefits, claims by third parties and any other damages
arising from or related to the use of the Device.

Simplified EU declaration of conformity:

Hereby, Fibar Group S.A. declares that the device is in compliance
with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
www.manuals.fibaro.com

WEEE Directive Compliance:

Device labelled with this symbol should not be disposed with other
household wastes. It shall be handed over to the applicable
collection point for the recycling of waste electrical and electronic
equipment.

Attention!

This product is not a toy. Keep away from children and animals!

This device complies with Part 15 of the FCC Rules

Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including
interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Notice

This device complies with Industry Canada license-exempt RSSs.
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux normes d’exemption de licence RSS
d’Industry Canada. Son fonctionnement est soumis aux deux
conditions suivantes: (1) cet appareil ne doit pas causer d’interféren­ce et (2) cet appareil doit accepter toute interférence, notamment les
interférences qui peuvent affecter son fonctionnement.

Note

Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your authority
to operate this equipment under Federal Communications
Commission’s rules.

This Device may be used with all devices
certified with Z-Wave certificate and should be
compatible with such devices produced by
other manufacturers.

i

Any device compatible with Z-Wave may be added
to Fibaro system.