Fiat 126 1987 1992 User Manual

FIAT

126 Bis (703 cm3)

1987 to 1992

Notes and Illustrations

704 cm3, 126

Weber DGF / FOS 30S2HR

704 cm

Engine and cooling system

Type Capacity (cm

) / number of cylinders Compression ratio / pressure bar Oil pressure bar Oil temperature ºC Valve clearance - inlet mm

Valve clearance - exhaust mm

Firing order No 1 cylinder position Thermostat opening temperature ºC Radiator cap pressure bar

Fuel system

Idle speed - manual [auto] rpm Fast idle speed - manual [auto] rpm CO @ idle speed [3000 rpm] - see page VI % HC @ idle speed [3000 rpm] - see page VI ppm CO2 @ idle speed [3000 rpm] - see page VI % O2 @ idle speed [3000 rpm] - see page VI % Carburettor / fuel injection

Type / ref Main jet / needle

Injection pressure bar Pump pressure bar Octane rating RON

Ignition system

Type Ignition coil

Primary resistance ohms

Ballast resistor ohms

Voltage - Tmnl 15(+) to earth V Distributor

Points gap (air gap) mm

Dwell angle º (%)

Condenser capacity µF

Rotation Ignition timing - basic [static º Crankshaft @ rpm

V = Vacuum NV = No Vacuum Total ignition advance º Crankshaft @ rpm

º Crankshaft @ rpm º Crankshaft @ rpm

Centrifugal check. º Crankshaft @ rpm

º Crankshaft @ rpm º Crankshaft @ rpm

Vacuum range check mbar

Maximum vacuum advance º Crankshaft

Spark plugs

Type

Electrode gap mm

Electrical system

Battery V / CC / RC Alternator voltage / full load current / engine rpm Starter motor current / voltage - cranking A / V

Starter motor current / voltage - locked A / V

Running gear

Brakes -

Front (min. friction material thickness) mm

Rear (min. friction material thickness) mm

Tyres

Saloon Size

Estate / Van Size

Pressure - front / rear - Saloon bar

Pressure - front / rear - Estate / Van bar

Front suspension / wheel alignment

Toe-in (+) / Toe-out (–) mm [º]

Camber

Castor

King pin inclination

Rear suspension / wheel alignment

Toe-in (+) / Toe-out (–) mm [º]

Camber

Torque wrench settings

Cylinder head - stage 1 Nm

Cylinder head - stage 2 Nm

Cylinder head - stage 3 Nm

Cylinder head - stage 4 Nm

Big-end bearings Nm Main bearings Nm Clutch cover Nm Flywheel [driveplate] Nm Front hubs Nm Rear hubs Nm Wheel nuts / bolts Nm Spark plugs Nm

Capacities

Engine oil & filter litres Gearbox - 4-speed [5-speed] litres Automatic transmission - refill litres Final drive litres Cooling system litres Fuel tank litres

126 A2.000 OHV 18.5kW 704 / 2

8.6±0.15 / _ [2.9 to 4.8] 100

0.15±0.05

0.15±0.05 1-2 _ 85 to 89

0.98

850±50 _

≤0.3 ≤200

_ _ Weber/FOS W: 30 DGF 3/150. F: 30S2HR W: 90, 90. F: 92, 90 _ ≥0.20 97[E 95 RON]

Contact breaker - CIS Biazet 101, Marelli BZ 600A

1.42 to 1.60 (typical) _ _ Marelli/Zelmot. M: 0.40±0.03

78±3

0.25±0.025 Clockwise 10 BTDC @ idle _ _ _ _ 0 to 2 @ 1400 8 to 12 @ 2300 16 to 20 @ 3000 71 to 267 13 to 17 Bosch/Champion WR7DC / RC9YC

0.70 to 0.80

12 / 140 / 34Ah

14.0 to 14.3 / 43, 45 / 3500 150 / 9.7 300 / 7.3

1.5

1.5 135/70x13

1.5 / 2.0 _

+2.0 to 6.0 +1°40’±30’ +9°±1° _

+1.5 to 5.5 +3°±30’

M8 bolts: 24 M9 bolts: 40 Nuts: 49 _ 34 27 10 44 WSM _ 69 25 to 30

2.25

1.1 _ WT

4.8 21

Z: 0.47 to 0.55

Click on one of the

buttons above to view

data for this car. To

return to this screen and

make another choice, click anywhere on the

data screen.

Automotive Technical

DATA BOO K

126 Bis (703 cm3) 1987 to 1992

126 Bis (703 cm

) 1987 to 1992

126 Bis (703 cm

) 1987 to 1992

126 Bis (703 cm

) 1987 to 1992

126 Bis (703 cm

) 1987 to 1992

126 Bis (703 cm

) 1987 to 1992

126 Bis (703 cm

) 1987 to 1992

FIAP0010701

Engine &

Cooling

Fuel Ignition Electrical

Running

gear

Torque

settings

Capacities

Notes &

Illustrations

MENU HELP

1: Idle speed 2: CO / Mixture