FHF SLD 1, SLD 2, SLD 3 User Manual
FUNKE+HUSTER•FERNSIG
Rotating Mirror Beacons
SLD 1/SLD 2/SLD 3
Optical signalling devices
for use in noisy environments
Warning signal without noise
3
Continuous operation
3
Available for usual supply voltages
3
Blue and yellow light for 12 VDC or 24 VDC
3
with general design approval for use
on vehicles by the German traffic authorities
Application
The rotating mirror beacons enable safe
and reliable signalling in noisy environments. Indoors the signal is even noticed
when the light source itself is not visible
because the light flashes are reflected
by walls and other objects. The SLD 1
and SLD 2 rotating mirror beacons use
H1 halogen lamps 12 V, 55 W or 24 V,
70 W. The caps come in the colours
transparent, red, amber, green and blue.
The power supply and vibrationabsorbing mounting of the chassis of
the SLD 3 rotating mirror beacon make
it especially suitable for use on forklift
trucks.
It comes in two version with a 36 VDC to
60 VDC or 80 VDC to 120 VDC power
supply.
Design
The SLD 1 rotating mirror beacon is a
version for mounting on horizontal
sur faces. It can also be fitted on slightly
sloping surfaces (for example top of
a car) by placing a DPR rubber gasket
between it and the sur face.
It can further be mounted on an ASFL
extension flange placed on a vertical rod.
The SLD 2 rotating mirror beacon can
be mounted on an ASTR extension rod.
The connection cable then runs through
the extension rod.
This beacon is intended for use on vehicles and is only avail able for operation
on 12 VDC or 24 VDC power supplies.
Warning device
on mobile
machines
SLD1 on morable crane
FUNKE+HUSTER•FERNSIG
Technical specifications
Housing Plastic socket with die cast metal bottom
(for SLD 1 and 3) and full-surface PVC sealing
Cap Plexiglass
Colours Transparent, red, amber, green, blue
Protection degree IP 54 (IEC 529)
Protection class I
Cable entry From below
1.5 mm
2
single wire
2
fine wire
Connection terminals Cross section: 2.5 mm
Operating conditions Indoors and outdoors
Operating position Mounted vertically on a horizontal surface,
extension rod, wall holder, etc.
Operating mode Continuous
Reflector speed Approx. 180 rpm
Temperature range
Operation -20 °C to +50 °C
Storage -30 °C to +70 °C
Approval German Federal Office ABG No. K 8697 (blue)
for Motor Traffic ABG No. K 8698 (amber)
Weight SLD1 approx. 2.3 kg
SLD 1
SLD 2
12, 24 VDC
12, 24 VDC
approx. 1.4 kg
approx. 1.0 kg
SLD 3 approx. 2.0 kg
Order information
* The full article
number is made up by
ppending the colour
a
code for the coloured
ap to the article
c
numbers given below.
transp.
red
amber
green
blue
01
02
03
04
05
Type Name Rated Operating Current Fuse 5 x 20 Art. no.*
voltage U
SLD 1 Rotating Mirror Beacon*
SLD 1 Rotating Mirror Beacon*
SLD 1 Rotating Mirror Beacon*
SLD 1 Rotating Mirror Beacon*
SLD 2 Rotating Mirror Beacon*
SLD 2 Rotating Mirror Beacon*
SLD 3 Rotating Mirror Beacon*436–60 VDC +10/-15 % 222 013
SLD 3 Rotating Mirror Beacon*480–120 VDC +10/-15 % 222 014
1
110 VAC +10/-15 % 0.46 A T 1.2 A 222 003
1
230 VAC +10/-15 % 0.23 A T 0.63 A 222 004
2
3
2
3
12 VDC +10/-15 % 4.80 A T 6.3 A or 8 A car fuse 222 001
24 VDC +10/-15 % 3.00 A T 6.3 A or 8 A car fuse 222 002
12 VDC +10/-15 % 4.80 A T 6.3 A or car fuse 222 011
24 VDC +10/-15 % 3.00 A T 6.3 A or car fuse 222 012
Spares
Cap 229 110 . .
Halogen Lamp 12 V/55 W 229 111 12
Halogen Lamp 24 V/70 W 229 111 24
volt. range Ueconsumption
e
T = time lag
Accessories
Extension Rod 222 019 01
Mounting Flange 222 009 11
WH 4 Wall Holder 222 009 12
. .
. .
. .
. .
. .
. .
. .
. .
. .
Protective Cage 222 009 13
1
*
With transformer; lamp H 1, 12 V, 55 W *2Lamp H 1, 12 V, 55 W
3
*
Lamp H 1, 24 V, 70 W *4The SLD 3 is supplied without lamp (bulb with Ba 15 S socket needed, max. 40 W)
Subject to change without notice · Printout 07/11
FHF Funke + Huster Fernsig GmbH ·
Telephone +49- 208-82 68 - 0 · Fax +49-208-82 68-286 · http://www.fhf.de · e-mail: info@fhf.de
P.O. Box 14 01 66 · D-45441 Mülheim an der Ruhr
· Gewerbeallee 15-19 · D-45478 Mülheim an der Ruhr
Loading...