Page 1
User guide
Video door phones
RoHS
Page 2
Table of contents
2
Description of the door stations .................................................. 3
Description of the symbols in the diagrams (door stations) .......... 7
Description of monitors .............................................................. 12
Description of the symbols in the diagrams (monitors) ................ 21
Installation ................................................................................ 26
27
Wiring diagram of CCTV camera ................................................ 41
Operating the video door phone 42
Warranty card ..................................................................... 45
Programming of the door station with combination lock ............... 8
Programming of the door station with card reader ....................... 10
Operating the monitor with memory............................................ 23
Wiring diagram ..........................................................................
..................................................
Page 3
Dimensions: 55×135×39 mm
KK-01B, KK-01G, KK-01S
Description of the door stations
1: audio-red
2: ground-blue
3: camera power supply
from the monitor4: video-white
5: bolt-black
6: bolt-black
yellow
Bolt
Monitor
6
3
Volume
control
Dimensions: 75×182×60 mm
KK-03
1: audio-red
2: ground-blue
3: camera power supply from the monitor-yellow
4: video-white
5: additional bolt release button
6: DC12-14,5V power supply* (-)/bolt (-) /bolt switch
7:
do not connect
* power supply FF: ZV-14
access block for users 10-20 and 36-40
8: bolt (+)
9: DC12-14,5V power supply* (+)
10:
DC12V
power supply
_
+
Monitor
Volume
control
5
6
7
8
9 10
red
blue
yellow
white
Bolt
release
button
EXIT
2
3
4
5
6
7
1
10
2
3
4
5
6
7
11
1
Page 4
KK-04
Dimensions: 150×203×55 mm
Installation box dimensions:
130×183×50 mm
1: audio-red
2: ground-blue
3: camera power supply
from the monitor-yellow
4: video-white
5: bolt-black
6: bolt-black
Bolt
Monitor
6
Volume
control
Dimensions: 120×250×51 mm
Installation box dimensions:
110×240×46 mm
KK-05
1: audio-red
2: ground-blue
3: camera power supply
from the monitor-yellow
4: video-white
5:
: DC12-14,5V power supply* (-) black
* power supply FF: ZV-14
bolt
6: bolt
8: DC12-14,5V power supply* (+) red
9
Bolt
Monitor
6
Volume
control
Power
supply
8
9
Bolt release
button
EXIT
Access block button
for users 10-20
and 36-40
4
2
3
4
5
6
7
2
3
4
5
6
7
10
11
8
Page 5
KK-08
Dimensions: 120×250×51 mm
Installation box dimensions:
110×240×46 mm
Please note!
Remove the jumper J3
in all monitors and uniphones
Access block button
for users 10-20 and 36-40
Bolt
Monitor 2
6
Volume
control
Power
supply
8
9
Bolt release
button
EXIT
Monitor 1
1: audio-red
2: ground-blue
3: camera power supply
from the monitor-yellow
4: video-white
5:
: DC12-14,5V power supply* (-) black
* power supply FF: ZV-14
bolt
6: bolt
8: DC12-14,5V power supply* (+) red
9
KK-08K
Dimensions: 120×250×51 mm
Installation box dimensions:
110×240×46 mm
Please note!
Remove the jumper J3
in all monitors and uniphones
1: audio-red
2: ground-blue
3: camera power supply
from the monitor-yellow
4: video-white
5: bolt
: DC12-14,5V power supply* (-) black
* power supply FF: ZV-14
6: bolt
8: DC12-14,5V power supply* (+) red
9
Access block button
for users 10-20 and 36-40
Bolt
Monitor 2
6
Volume
control
Power
supply
8
9
Bolt release
button
EXIT
Monitor 1
5
3
4
5
7
6
8
10
11
2
3
4
5
7
10
12
2
6
8
Page 6
KK-09
Dimensions: 120×250×51 mm
Installation box dimensions:
110×240×46 mm
Please note!
Remove jumper J3
in all monitors and uniphones
Bolt
6
Volume
control
Power
supply
8
9
Monitors
1: audio-red
2: ground-blue
3: camera power supply
from the monitor-yellow
4: video-white
5:
: DC12-14,5V * (-) black
* FF: ZV-14
bolt
6: bolt
8: DC12-14,5V power supply* (+) red
9 power supply
power supply
6
2
3
4
5
6
7
8
Page 7
7
Technical data
Main power supply,
bolt, keypad or RFID
power supply
DC 12V from monitor KK-01
ZV-14 power supply KK-03
ZV-14 power supply KK-05÷KK-09
Power consumption
during operation 1,5 W
Camera angle
about 70° (adjustable)
Operating temperature range
Minimum illumination
0,05 Lux
Converter
1/3 CCD
IP
55
Backlight
LED
-25C ÷ +55C
Protection cowl
LED
Camera
Speaker
Call button
Microphone
Camera mounting screw
Signboard for name
Keyboard
Cable ducting
LED indicating operating status of the keypad
Card reader
Function descriptionNo.
Description of the symbols
in the diagrams (door stations)
1
2
3
4
5
6
7
8
9
10
11
12
Page 8
1. Programming user access code:
a) press , you will hear two short beeps:
b) enter the master code ( – factory settings),you will hear
three short beeps, red LED will begin to flash;
c) enter user number from 01 to 40, you will hear two short beeps (users
with numbers from 31 to 40 can open the door for an indefinite period of
time - the doors remain open until re-entering the code);
d) enter a 4-digit user code, you will hear 3 short beeps;
e) return to step 3 to set more users or press to complete the
programming; after pressing you will hear five beeps.
2. Deleting user code:
a) press , you will hear two short beeps;
b) enter the administrator code, you will hear three short beeps,
red LED will begin to flash;
c) enter user number from 01 to 40 that you want to delete, you will
hear two short beeps;
d) press , you will hear three short beeps;
e) return to step 3 in case of removing more user codes or press to
complete the removal, after pressing you will hear five short
beeps.
3. Programming the lock opening time:
a) press , you will hear two short beeps;
b) enter the administrator code, you will hear three short beeps,
red LED will begin to flash;
c) enter , you will hear two short beeps;
d) enter the required opening time from 01 to 99 seconds (2 digits) you
will hear three short beeps;
e) press to complete programming, you will hear five short beeps.
4. Changing the administrator code:
(factory set master code is: 1234)
a) disconnect the power supply;
b) press and hold the button, connect the power (while holding
the button pressed), door station will generate a long, continuous
sound;
c) when the sound is over, please release the button , you will
hear one short beep and a red LED will flash;
d) enter new, four-digit administrator code.
1
2
3
4
0
0
Programming of the door station
with combination lock
8
Page 9
9
5. Opening the door with a code
a) enter a 4-digit user code, the red LED lights, the door will open.
6. Reset all user codes (except the administrator code)
a) press , you will hear two short beeps;
b) enter administrator code, you will hear three short beeps, red LED will begin
to flash;
c) press , you will hear two short beeps, the LED flashes;
d) press , you will hear two short beeps, the LED flashes;
e) press successively six times, you will hear one short beep, the LED
flashes;
f) press , you will hear five short beeps, the LED goes out, the system reset.
Page 10
1. Adding a user card with the MASTER card:
a) Bring the MASTER card close to the reader, you will hear one short and one
long beep;
b) Then enter the last 6 digits of the card number or move it closer to the
reader, saving your card in the memory will be confirmed with long beep;
c) If you want to add more cards, repeat step 2 as many times as needed;
d) To exit the card adding mode, bring the MASTER card close to the
reader, you will hear three short beeps – the device is ready for
operation.
2. Enter programming mode:
PLEASE NOTE!
The DH 12-R remote control is necessary for programming the door station.
The remote control is not included in the door station package.
a) to enter the programming mode, point the remote control at LED located on the
door station and enter the factory code , you will hear a tone
confirming the change of the operating mode, and the LED located on the
station will change its color from red to orange;
b) exit the programming mode by pressing the , the tone and LED color change
to red will confirm a return to operating mode.
3. Adding user card:
a) Enter the programming mode (see point 1);
b) Press number on the remote control, you will hear a long beep;
c) Enter the last 6 digits of the card number or bring it closer to the
reader – short beep means the card was accepted, the next long
beep confirms card saving;
d) If you want to add more cards, repeat step 3 as many times as needed;
e) If you bring closer a card that is already registered, you will hear four short
beeps;
f) To exit the user card adding mode, press .
4. Removing the card:
a) To remove the registered card the device should be
put in to a programming mode (see point 1);
b) Press number on the remote control, you will hear a long beep;
c) Enter the last 6 digits of the card number you want to delete or bring it
closer to the reader. You will hear one short and one long beep confirming
the removal of the card;
To exit the user card adding mode, press
d) .
2
1
Programming of the door station
with card reader
10
4
5
6
7
Page 11
5. Removing all cards:
1) Enter the programming mode (see point 1);
2) Press number on the remote control, you will hear a long beep.
Wait for the audio signal to end, it will confirm the deletion of all cards from
the door station memory;
3) Return to operation after pressing .
6. Administrator code change:
1) Enter the programming mode (see point 1);
2) Press number on the remote control, you will hear a long beep;
3) Enter the new four-digit code and confirm by pressing , re-enter the
new code and confirm it by pressing . You will hear a long beep
confirming the change of the code administrator;
4) Return to operation after pressing .
7. Programming the MASTER card:
1) Enter the programming mode (see point 1);
2) Press number on the remote control, you will hear a long beep and the LED
will change its color to orange;
3) Enter the last 6 digits of the card number that is to be the MASTER card or bring it
closer to the reader, you will hear one short and one long beep confirming your card
has been saved in the memory;
4) To exit card adding mode, press , you will hear a long beep and the LED
will change its color to red – the device is ready to work;
5) MASTER cards cannot be removed, only new card can be programmed in place
of damaged or lost card.
8. Restoring the forgotten administrator code:
1) Turn off power supply for at least 10 seconds;
2) Connect the power supply and when the LED is flashing (six times),
press the on the remote control, you will hear the beep confirming
the restoration of the MASTER code to default value: 4567.
9. Programming the lock opening time:
1) Enter the programming mode (see point 1);
2) Press number on the remote control, you will hear long beep;
3) Enter the desired time of electric lock opening from 01 to 99 seconds
(two-digits);
4) You will hear a long beep confirming the change in lock time opening;
5) Exit the programming mode by pressing .
10. Opening the lock with the card:
1) Bring the card to the reader at a distance of 5 cm;
2) Opening the lock is indicated by the green LED on the door station.
0
7
8
9
9
11
4
Page 12
12
Description of monitors
Dimensions: 241×161×23 mm
MK-03G (black), MK-03W (white)
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
10) connection to the control input of the door
automaton, it is a closing contact
of the NO relay (dry contact).
Do not connect voltages greater than 24 V,
the current should not exceed 150 mA.
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line
a) jumper put on – coaxial cable, if the system has more than one monitor installed,
leave only the jumper in the last monitor and remove it in all the other monitors
b) jumper removed – other cable
J3: switching on or off the backlight of the call button and the signboard in KK-04 door
station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
10
10
1
2
3
4
1
2
3
4
8
9
J3
J2
J1
POW
connection
of the door
station 2
connection
of the DC 14.5 V
power supply
connection
to the control input
of the door automaton
10 10
12
3
4
12
3
4
89
J3
J2
J1
POW
connection
of the door
station 1
1
2
3
4
5
15
14
8 9
10
11
Page 13
13
MK-04B, MK-04W
Dimensions: 245×160×18 mm
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line
a) jumper put on – coaxial cable, if the system has more than one monitor installed,
leave only the jumper in the last monitor and remove it in all the other monitors
b) jumper removed – other cable
J3: switching on or off the backlight of the call button and the signboard in KK-04
door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
10) connection to the control input of the door
automaton, it is a closing contact
of the NO relay (dry contact).
Do not connect voltages greater than 24 V,
the current should not exceed 150 mA.
- jumper open
- jumper closed
connection
of the DC 14.5 V
power supply
connection
to the control input
of the door automaton
10 10
12
3
4
1
2
3
4
89
J3
J2
J1
POW
connection
of the door
station 2
connection
of the door
station 1
6
7
1
2
3
4
5
14
8 9
10
Page 14
14
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line
a) jumper put on – coaxial cable, if the system has more than one monitor installed,
leave only the jumper in the last monitor and remove it in all the other monitors
b) jumper removed – other cable
J3: switching on or off the backlight of the call button and the signboard in KK-04
door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
MK-06B
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
10) connection to the control input of the door
automaton, it is a closing contact
of the NO relay (dry contact).
Do not connect voltages greater than 24 V,
the current should not exceed 150 mA.
Dimensions: 282×135×23 mm
Door automaton control
connection
of the DC 14.5 V
power supply
connect ion
to the cont rol inp ut
of the door a utoma ton
10 10
1
2
3
4
12
3
4
89
J3
J2
J1
POW
connection
of the door
station 2
connection
of the door
station 1
12
2
3
4
5
6
11
8
9
10
Page 15
15
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line depending on the number of monitors in the system:
a) 1 monitor: jumper put on + resistor
on the cables between video and ground
b) 2 monitors: jumpers in two monitors put on
c) 3 monitors: jumper removed in first monitor,
put on in monitors 2 and 3
d) 4 monitors: jumper removed in first
and second monitor, put on in 3 and 4
J3: switching on or off the backlight of the call button
and the signboard in KK-04 door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
10) connection to the control input of the door
automaton, it is a closing contact
of the NO relay (dry contact).
Do not connect voltages greater than 24 V,
the current should not exceed 150 mA.
Dimensions: 282×135×23 mm
MK-06WF
Cursors
Menu exit
Menu
Door automaton control
connection
of the DC 14.5 V
power supply
connect ion
to the cont rol inp ut
of the door a utoma ton
10 10
1
2
3
4
12
3
4
89
J3
J2
J1
POW
connection
of the door
station 2
connection
of the door
station 1
white
yellow
blue
red
Resistor
50÷120 Ω
Camera
2
3
4
5
6
12
11
8
Page 16
16
MK-07WB
Dimensions: 240×170×23 mm
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
10) connection to the control input of the door
automaton, it is a closing contact
of the NO relay (dry contact).
Do not connect voltages greater than 24 V,
the current should not exceed 150 mA.
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line
a) jumper put on – coaxial cable, if the system has more than one monitor installed,
leave only the jumper in the last monitor and remove it in all the other monitors
b) jumper removed – other cable
J3: switching on or off the backlight of the call button and the signboard in KK-04
door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
1
2
3
4
1
2
3
4
8
9
J3
J2
J1
POW
connection
of the DC 14.5 V
power supply
12
3
4
12
3
4
89
J3
J2
J1
POW
connection
of the door
station 2
connection
of the door
station 1
8910
14
1
2
3
4
5
Page 17
17
MK-08F
Dimensions: 241×161×23 mm
Menu
Menu exit
Navigation
cursors
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
10) connection to the control input
of the door automaton, it is a closing
contact of the NO relay (dry contact).
Do not connect voltages greater than 24 V,
the current should not exceed 150 mA.
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line depending on the number of monitors in the system:
a) 1 monitor: jumper put on + resistor
on the cables between video and ground
b) 2 monitors: jumpers in two monitors put on
c) 3 monitors: jumper removed in first monitor,
put on in monitors 2 and 3
d) 4 monitors: jumper removed in first
and second monitor, put on in 3 and 4
J3: switching on or off the backlight of the call button
and the signboard in KK-04 door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
connection
of the DC 14.5 V
power supply
connection
to the control input
of the door automaton
10 10
12
3
4
12
3
4
89
J3
J2
J1
POW
10
10
1
2
3
4
1
2
3
4
8
9
J3
J2
J1
POW
connection
of the door
station 2
connection
of the door
station 1
white
yellow
blue
red
Resistor
50÷120 Ω
Camera
1
2
3
4
5
15
14
8
11
Page 18
18
MK-09W
Dimensions: 218×167×33 mm
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line
a) jumper put on – coaxial cable, if the system has more than one monitor installed,
leave only the jumper in the last monitor and remove it in all the other monitors
b) jumper removed – other cable
J3: switching on or off the backlight of the call button and the signboard in KK-04
door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
connection
of the DC 14.5 V
power supply
12
3
4
12
3
4
89
J3
J2
J1
POW
10
10
1
2
3
4
1
2
3
4
8
9
J3
J2
J1
POW
connection
of the door
station 2
connection
of the door
station 1
1
2
4
5
8 9
10
11
14
Page 19
19
MK-10F
Dimensions: 241×161×23 mm
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line
a) jumper put on – coaxial cable, if the system has more than one monitor installed,
leave only the jumper in the last monitor and remove it in all the other monitors
b) jumper removed – other cable
J3: switching on or off the backlight of the call button and the signboard in KK-04
door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
Save photo button
Preview photo button
Navigation cursors
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
10) connection to the control input
of the door automaton, it is a closing
contact of the NO relay (dry contact).
Do not connect voltages greater than 24 V,
the current should not exceed 150 mA.
10
10
1
2
3
4
1
2
3
4
8
9
J3
J2
J1
POW
connection
of the DC 14.5 V
power supply
connection
to the control input
of the door automaton
10 10
12
3
4
12
3
4
89
J3
J2
J1
POW
connection
of the door
station 2
connection
of the door
station 1
15
1
2
3
4
5
14
8 9
10
11
Page 20
20
MU-01
Dimensions: 100×200×45 mm
connect ion
of the DC 14. 5 V
power sup ply
1
2
3
4
1
2
3
4
8 9
J3
J2
J1
POW
MU-02
Dimensions: 160×120×42 mm
J1, J2, J3 jumper configuration:
J1: switching on or off the chime in the door station
a) jumper put on – audible chime
b) jumper removed – chime off
J2: fit the cable in the video line
a) jumper put on – coaxial cable, if the system has more than one monitor installed,
leave only the jumper in the last monitor and remove it in all the other monitors
b) jumper removed – other cable
J3: switching on or off the backlight of the call button and the signboard in KK-04
door station:
a) jumper put on – backlight on
b) jumper removed – backlight off
In case of door stations other than KK-04, the jumper must be removed.
1) audio-red
2) ground-blue
3) camera power supply-yellow
4) video-white
8) (+) of power supply-red
9) (-) of power supply-black
earphone
connection
1 2
3
4
1
2
3
4
connect ion
of the DC 14. 5 V
power sup ply
8 9
POW
J3
J1
connection
of the door
station 2
connection
of the door
station 1
connection
of the door
station 2
connection
of the door
station 1
7
1
3
4
12
8
9
10
1
2
7
4
5
Page 21
21
LED
Installation connectors
Earphone
Microphone
Call answering button
Bolt release button
Screen
Speaker
Camera preview button
Intercom button
Door automaton control
Brightness adjusting
Call volume adjusting
Color adjusting
Ringer volume adjusting
DC 14,5V
During operation 7W
10" LCD / 7"LCD / 4"LCD
Technical data
Power supply
Power consumption
Screen
Operating temperature range
-10°C ÷ +55°C
Description of the symbols in the diagrams
(monitors)
MK-03G (black), MK-03W (white), MK-04W,
MK-04B, MK-06B, MK-06WF, MK-07WB, MK-09W,
MU-01, MU-02
Function descriptionNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Page 22
22
LED
Installation connectors
Earphone
Microphone
Function descriptionNo.
Call answering button
Bolt release button
Screen
Speaker
Camera preview button
Intercom button
Door automaton control
Brightness adjusting
Call volume adjusting
Color adjusting
Ringer volume adjusting
DC 14,5V
During operation 7W
10" LCD / 7"LCD / 4"LCD
Technical data
Power supply
Power consumption
Screen
Operating temperature range
-10°C ÷ +55°C
MK-08F, MK-10F
Menu exit
Navigation cursor UP
Menu
Navigation cursor DOWN
Browse photos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Page 23
Monitor memory can store up to 100 photos. If the memory is full, oldest images are
automatically deleted and new ones will be saved in their place.
After pressing the call button by the guest, the device automatically saves one photo
from the camera after 3 seconds from pressing the button. Switching the monitor to
preview mode will also automatically save 1 photo. The blue LED below the memory
control button indicates that a photo not yet viewed is stored in the memory.
Viewing photos
When you press or arrow the screen will display the latest photo stored in the
memory. If there are not yet viewed photos in the memory, the Unseen message will be
displayed in the upper left corner of the screen with a number indicating the number of
newly saved photos. Pressing or arrows chooses older or newer photos. To exit this
menu press button or wait 10 seconds without executing any other operation.
Deleting photos
Pressing the button opens the menu window. By pressing the button the appropriate number of times we go to the window Remove all - pressing the or arrow will
erase all photos from memory. To exit this menu press button or wait 10 seconds
without executing any other operation.
Adjusting display settings – brightness, contrast, color saturation
Pressing the button opens the menu window. By pressing the button the
appropriate number of times we go to the window Brightness, Contrast or Color – using
and arrows you can adjust desired parameter in the range of 0 to 100. To exit this
menu press button or wait 10 seconds without executing any other operation.
Setting the date
Pressing the button opens the menu window. By pressing the button the appropriate number of times we go to the window Date - pressing the or arrow will cause
the displayed year to flash - we set the desired year with arrow, then, by pressing the
button , we move to the month and day setting.
To exit this menu press button or wait 10 seconds without executing any other
operation
sy
ym
23
MK-08F
Operating the monitor with memory
Page 24
Monitor memory can store up to 400 photos. If the memory is full, oldest images are
automatically deleted and new ones will be saved in their place.
Automatic saving of photos
After pressing the call button by the guest, the device automatically saves one
photo from the camera after 5 seconds from pressing the button. Switching the monitor
to preview mode will also automatically save 1 photo.
Manual saving of images
After call by the guest or when the preview is enabled, each time you press the
button one photo will be saved.
Viewing photos
After pressing the button the thumbnails of stored photos will be displayed on
screen. The screen can display up to six thumbnails. To select desired thumbnail, use
or cursor – thumbnail will be highlighted with yellow border. Pressing the
button will display selected photo in full screen mode. With or arrow or you can
browse the previous or next photos in full size or, by pressing the button, return to
the thumbnail preview.
If no button is pressed for 10 seconds, the monitor automatically returns to
standby mode.
Deleting individual photos
To delete the photos you need to enter the thumbnail preview mode. We choose
the desired thumbnail by highlighting it and by pressing the button we delete photo.
Photo can also be deleted when it is displayed in full size, also by pressing the
button.
Deleting all photos
Pressing arrow for three seconds in preview mode will delete all photos.
MK-10F
24
continued from previous page MK-08F
Setting the time
Pressing the button opens the menu window. By pressing the button the
appropriate number of times we go to the window Time - pressing the or arrow will
cause the displayed hour to flash - we set the desired hour with arrow, then, by pressing
the button, we move to the minutes and seconds setting.
To exit this menu press button or wait 10 seconds without executing any other
operation.
Page 25
25
continued from previous page MK-10F
Setting the clock
Pressing the button in standby mode (standby) for 5 seconds will open the
menu for setting the clock. The screen displays the date and time in format: yyyy-mmdd hh:mm. The corresponding values in the flashing fields are set with or
arrows. Settings are confirmed by pressing button, the device automatically
switches to set the following values of the current month, day of the week, hour and
minutes. After the minutes setting and the confirmation with button, the monitor
switches to standby mode.
Page 26
1. Do not install the unit in a location exposed to dust, direct sunlight, high temperatures
or high humidity.
2. Do not seal the camera with silicone.
3. Do not install the unit in areas exposed to vibration or shock.
1. Choose a place to install the monitor.
2. Attach the wall mount for the monitor installation (optimum height to place the monitor
is 155÷170 cm).
3. Connect the camera wires to the monitor.
4. Attach the monitor to the mount.
5. Connect the monitor power supply.
Installation
26
Page 27
Wiring diagram
DC 14,5V
power supply
DC 14,5V
power supply
DC 14,5V
power supply
DC 14,5V
power supply
4p
4p
4p
4p
4p
4p
4p
4p
DC12V
power supply
DC12V
power supply
22
Door
station 1
Door
station 2
Bolt
Bolt
1. Before installing and operating this video door phone set, you should carefully read
the following instructions. Improper connection and damages caused by it are not covered
by the warranty.
2. When connecting the power supply to the video door phone, pay special attention
to the correct connection of the power supply polarity!
Incorrect connection will damage the video door phone!
3. For installation up to 30 m use cables with a minimum diameter of 0.50 mm; for instal lation of more than 30 m - min. 0.70 mm.
For the best image quality in video line, we recommend use of a 75 Ω coaxial cable.
4. ZV-14 power supply is recommended to power the bolt.
27
Page 28
KK-01 / KK-04
1 door station + 1 monitor or uniphone
1 door station + 2 monitors or uniphones
white
blue
red
yellow
Monitor 1
Monitor 2
DC14,5V
power supply
- +
DC14,5V
power supply
- +
white
blue
red
yellow
Door
station 1
Monitor 1
DC14,5V
power supply
- +
ZV-14
power
supply
red
black
red
black
red
black
Bolt
Bolt
ZV-14
power
supply
Door
station 1
28
Page 29
2 door station + 1 monitor or uniphone
Monitor 1
DC14,5V
power supply
- +
white
blue
red
yellow
Door
station 1
ZV-14
power supply
ZV-14
power supply
red
black
white
blue
red
yellow
Bolt
Bolt
Door
station 2
KK-01 / KK-04
29
Page 30
2 door station + 2 monitors or uniphones
KK-01 / KK-04
Monitor 1
DC14,5V
power supply
- +
Monitor 2
DC14,5V
power supply
- +
white
blue
red
yellow
Door
station 1
ZV-14
power supply
ZV-14
power supply
red
black
red
black
white
blue
red
yellow
Bolt
Bolt
Door
station 2
30
Page 31
1 door station
+ 1 monitor or uniphone
KK-03
Door
station 1
Bolt
Bolt
release
button
ZV-14
power supply
- +
Monitor 1
DC14,5V
power supply
- +
red
black
white
blue
red
yellow
1 door station
+ 2 monitors or uniphones
DC14,5V
power supply
- +
Door
station 1
DC14,5V
power supply
- +
red
black
red
black
white
blue
red
yellow
Bolt
Bolt
release
button
ZV-14
power supply
- +
Monitor 1
Monitor 2
31
Page 32
KK-03
2 door stations + 1 monitor or uniphone
Monitor 1
DC14,5V
power supply
- +
white
blue
red
yellow
Door
station 2
white
blue
red
yellow
Door
station 1
red
black
Bolt
Bolt
release
button
ZV-14
power supply
- +
Bolt
Bolt
release
button
ZV-14
power supply
- +
32
Page 33
2 door stations + 2 monitors or uniphones
KK-03
Monitor 1
Door
station 1
Door
station 2
DC14,5V
power supply
- +
Monitor 2
DC14,5V
power supply
- +
red
black
red
black
white
blue
red
yellow
white
blue
red
yellow
Bolt
Bolt
release
button
ZV-14
power supply
- +
Bolt
Bolt
release
button
ZV-14
power supply
- +
33
Page 34
34
1 door station
+ 1 monitor or uniphone
KK-05
Door
station 1
Bolt
ZV-14
power supply
+
-
Monitor 1
DC14,5V
power supply
- +
red
black
white
blue
red
yellow
1 door station
+ 2 monitors or uniphones
DC14,5V
power supply
- +
DC14,5V
power supply
- +
red
black
red
black
Monitor 1
Monitor 2
Door
station 1
Bolt
ZV-14
power supply
+
-
white
blue
red
yellow
Page 35
35
KK-05
2 door stations + 1 monitor or uniphone
Monitor 1
DC14,5V
power supply
- +
white
blue
red
yellow
white
blue
red
yellow
red
black
Door
station 1
Bolt
ZV-14
power supply
+
-
Door
station 1
Bolt
ZV-14
power supply
+
-
Page 36
36
2 door stations + 2 monitors or uniphones
KK-05
Monitor 1
DC14,5V
power supply
- +
Monitor 2
DC14,5V
power supply
- +
red
black
red
black
white
blue
red
yellow
white
blue
red
yellow
Door
station 1
Bolt
ZV-14
power supply
+
-
Door
station 1
Bolt
ZV-14
power supply
+
-
Page 37
KK-08 / KK-08K
1 door station + 2 monitors or uniphones
Door station 1
Bolt
ZV-14
power supply
- +
black
Monitor 2
DC14,5V
power supply
- +
red
white
blue
red
yellow
Monitor 1
DC14,5V
power supply
+ -
white
blue
red
yellow
37
black
red
black
red
Page 38
KK-08 / KK-08K
2 door stations + 2 monitors or uniphones
Door
station 1
Bolt
ZV-14
power supply
- +
black
Monitor 2
DC14,5V
power supply
- +
red
white
blue
red
yellow
Monitor 1
DC14,5V
power supply
+ -
white
blue
red
yellow
red
black
Bolt
ZV-14
power supply
- +
black
red
red
blue
yellow
white
white
yellow
blue
red
Door
station 2
38
black
red
Page 39
1 door station + 4 monitors or uniphones
Door
station
Bolt
Monitor 1 a
white
blue
red
yellow
Monitor 1 b
DC14,5V
power supply
+ -
red
blue
white
yellow
DC14,5V
power supply
+ -
ZV-14
power supply
- +
white
blue
red
yellow
Monitor 2 a
white
blue
red
yellow
Monitor 2 b
DC14,5V
power supply
- +
DC14,5V
power supply
- +
KK-08 / KK-08K
39
red
black
red
black
red
black
red
black
red
black
Page 40
KK-09
Door
station
Monitor 2
DC14,5V
power supply
+ -
white
blue
red
yellow
Monitor 4
DC14,5V
power supply
+ -
white
blue
red
yellow
Monitor 6
DC14,5V
power supply
+ -
white
blue
red
yellow
Monitor 8
DC14,5V
power supply
+ -
white
blue
red
yellow
ZV-14
power supply
+ -
Bolt
DC12V
40
red
black
red
black
red
black
red
black
Page 41
Monitor
Door station
CCTV camera
Power supply
In the case of low fence you can connect any CCTV camera instead
of a camera in the door station.
Monitor
Door station
CCTV camera
Power supply
Instead of a second door station you can install any CCTV camera.
yellow
black
red
white
yellow
blue
red
white
blue
red
yellow
blue
red
white
black
Wiring diagram of CCTV camera
41
Page 42
Operating the video door phone
2) The monitor displays an image of the visitor
and plays the chime, press button
to communicate with the visitor.
3)
.
If no one answers, the monitor automatically
turns off after 1 minute
4) If you want to open the door, press the door
release button .
1) Guest presses the call button on the camera.
1) If you want to observe the surroundings
located in front of the camera
on the monitor, press the preview
button .
2) If two cameras are installed in the system:
a) press the button once:
turn on the camera1
b) press the button for a second time:
turn on the camera 2
c) press the button for a third time:
the monitor turns off
Calls
Preview
42
Page 43
Operating the video door phone
continued
Intercom
If two or more monitors are installed
in the system:
to call a second monitor, press the intercom
button .
The call signal will ring on the second monitor (screen will remain blank):
a) to establish communication
with the first monitor, press the button
of call receiving .
b) to end the call,
press the button again .
43
Page 44
European Council Directive 2002/96/EC on The Waste
Electrical and Electronic Equipment Directive (WEEE
Directive) imposes a ban on the disposal of old
household electrical appliances as unsorted municipal
waste. Old appliances must be collected separately
and sorter in order to optimize recovery and recycling
of certain components and materials. This allows reducing environmental pollution and has a positive impact on the human health.
Crossed „trashcan” sign on the product reminds the client of his
obligation of a special sorting. Consumers should contact with local
authorities or retailer for information on dealing with used electric and
electronic equipment.
44
Page 45
1. The F&F Filipowski Sp. j. company provides warranty for purchased products
for 24 months from the date of purchase placed on this Warranty Card proof
of purchase.
2. Product defects revealed during the warranty period will be repaired free
of charge within 21 days from the date of the product acceptance in a service
point.
3. User has the right to replace the product for a new one if:
* four major repairs were made during the warranty period and the product is still
defective;
* if the fault has been deemed impossible to remove. When the product is
replaced for a new one, the equivalent of elements missing or damaged by the
User (including packaging) and the cost of their replacement shall be deducted.
4. The user delivers the defective equipment at his own expense to the service
point.
5. The warranty does not cover the decline in the quality of equipment due
to normal wear and tear and the following cases:
* improper or inconsistent with the user manual use of the product;
* usage or leaving the product in unsuitable conditions (excessive humidity, too
high or too low temperature, sunshine, etc.), different conditions for maintenance and operation than those that can be found in the operating manual
of the product;
* mechanical, chemical, thermal damage;
* damage caused by external forces such as surges on the electricity network,
lightning, flood, fire;
* damage caused by improper installation of equipment, improper storage of
equipment or repairs performed by unauthorized persons;
* damage caused by improper power supply.
6. The warranty expires as a result of:
* breaking or damaging the warranty seals;
* connection of additional equipment, other than recommended by the
manufacturer of the product;
* alterations and changes in product construction and repairs performed outside
the service point of the F&F;
* the warranty card or serial numbers have been altered, blurred or obliterated;
7. Warranty Card is valid only with entered date of purchase, confirmed by the
stamp and signature of the seller.
8. The repair condition is delivering the goods with this Warranty Card and proof
of purchase.
9. Service point:
F&F Filipowski Sp. j.
Konstantynowska 79/81
95-200 Pabianice,
phone: (+48 42) 215 23 83;
(+48 42) 227 09 71
e-mail: handlowy@fif.com.pl
www.fif.com.pl
Warranty card
45
Page 46
Product name:............................... Type:...........................................................
Data of sale:........................... Stamp and signature of the seller:...........................
Date
of repair
Repairs registration
Scope of repair
Signature
of techincian
46
Page 47
Date
of repair
Repairs registration continued
Scope of repair
Signature
of technician
47
Page 48
F&F Filipowski Sp. j.
Konstantynowska 79/81
95-200 Pabianice
phone: (+48 42) 215 23 83;
(+48 42) 227 09 71
e-mail: handlowy@fif.com.pl
www.fif.com.pl
Loading...