Fervi 0759 Operation And Service Manual
OPERATION AND
fervi.com
MAINTENANCE MANUAL
Partially assembled dust collector
Art. 0759
ORIGINAL INSTRUCTIONS
MACHINES AND
ACCESSORIES
fervi.com
FOREWORD
Read this manual before operating any machinery
ORIGINAL INSTRUCTIONS
Before starting any operation it is compulsory to read this instruction manual. The guarantee
that the machine will function and perform properly is strictly dependent upon the application
of all the instructions contained in this manual.
Operator Qualification
The operators assigned to using this machine must be supplied with all of the necessary
information and instruction and should be provided with adequate training regarding
safety in pertaining to:
a) The conditions of use of the equipment;
b) Foreseeable abnormal situations, pursuant to Article 73 of Legislative Decree
81/08.
We guarantee the Machine's conformity to the specifications and technical instructions
described in the Manual on the date of issuance and listed herein; On the other hand,
the machine may also be subject to important technical changes in the future, without
the manual being updated.
Therefore, see FERVI for information about modifications that could be implemented.
Page 2 of 29
REV. 3 October 2013
MACHINES AND
ACCESSORIES
fervi.com
CONTENTS
1 INTRODUCTION ........................................................................................4
1.1 Preface..........................................................................................................................5
2 SAFETY WARNINGS ..................................................................................6
2.1 General safety rules for machine tools.......................................................................... 6
2.2 Safety rules for electrical machine equipment ..............................................................8
2.3 Technical support.......................................................................................................... 8
2.4 Other provisions ...........................................................................................................8
3 TECHNICAL SPECIFICATIONS ...................................................................9
4 DESCRIPTION OF THE MACHINE .............................................................10
4.1 Identification plate ..................................................................................................... 11
4.2 Pictograms .................................................................................................................. 11
5 INSTALLATION OF THE MACHINE ...........................................................13
5.1 Assembling the vacuum ..............................................................................................13
5.2 Suction tube assembly ................................................................................................ 18
5.3 Connecting the plug and test start .............................................................................. 18
6 CONTROL SWITCHES............................................................................... 19
6.1 On switch (start) ........................................................................................................19
6.2 Stop button ................................................................................................................. 19
7 OPERATION ............................................................................................ 20
7.1 Emptying the chip collection bag ................................................................................ 20
8 MACHINE SAFETY DEVICES..................................................................... 21
8.1 Electrical safety devices .............................................................................................. 21
8.2 "Mechanical" Safety Devices .......................................................................................22
8.2.1 Protective casing...................................................................................................... 22
9 MAINTENANCE ........................................................................................ 23
9.1 Routine maintenance ..................................................................................................23
10 TROUBLESHOOTING .............................................................................24
11 REPLACEMENT PARTS........................................................................... 25
12 DISPOSAL OF PARTS AND MATERIALS ................................................. 28
13 ELECTRICAL CIRCUIT ........................................................................... 29
Page 3 of 29
MACHINES AND
ACCESSORIES
fervi.com
1 INTRODUCTION
This manual is delivered with the machine, and it must be regarded as an inseparable part of
it.
The manufacturer holds all ownership to material and intellectual property of this manual;
any disclosure or copying, even partial, of this publication without prior written consent is
forbidden.
The purpose of this manual is to provide the knowledge necessary for the use and
maintenance of the machine Aspiratore per trucioli Art. 0759 and create a sense of
responsibility and an understanding of the capabilities and limitations of the means entrusted
to the operator.
As the machine is entrusted to experienced and skilled operators, the following machine must
be perfectly known by the operator if you want it to be used safely and effectively.
Operators must be properly trained and prepared, so make sure that this manual is read and
consulted by the staff responsible for commissioning, operation and maintenance of the
Aspiratore per trucioli. This is to make all operations the safest and most effective possible
for those who carry out these tasks.
Therefore, it is imperative to strictly comply with the requirements in this manual, a
necessary condition for safe and satisfactory operation of the machine.
Before starting operation, installation and use of the Aspiratore per trucioli, authorised
staff must therefore:
carefully read this technical document;
know which protections and safety devices are available on the machines, their location
and how they work.
The buyer is responsible for ensuring that users are properly trained, that they are aware of
all the information and instructions in this document and that they are aware of the potential
risks of operating the Aspiratore per trucioli.
The manufacturer waives any and all responsibility for damage to people and/or
things caused by non-observance of the instructions in this manual.
The Aspiratore per trucioli was designed and built with mechanical guards and safety
devices designed to protect the operator/user from possible injury. It is strictly forbidden to
modify or remove guards, safety devices and caution labels. If this must be done (for
example, for cleaning or repair), make sure that no one can use the machine.
Modifications to the machine carried out by the user must be considered their sole
responsibility, therefore the manufacturer waives any and all responsibility for any
damage caused to persons and/or property resulting from maintenance performed
by unqualified personnel and in a manner unlike the operating procedures shown
below.
Page 4 of 29
MACHINES AND
ACCESSORIES
fervi.com
GRAPHIC REPRESENTATION OF SAFETY, OPERATIONAL AND RISK WARNINGS
The following boxes are designed to attract the attention of the reader / user for the proper
and safe use of the machine:
Pay attention
This highlights behavioural rules to prevent damage to the machine and/or the occurrence of
dangerous situations.
Residual Risks
This highlights the presence of dangers that cause residual risks to which the operator must
pay attention in order to avoid injury or damage to property.
1.1 Preface
For safe and easy operation of the Aspiratore per trucioli, this manual must be read
carefully in order to acquire the necessary knowledge. In other words, durability and
performance are strictly dependent on how it is used.
Even if already familiar with the Aspiratore per trucioli, it is necessary to follow the
instructions contained herein, in addition to the general precautions to be observed while
working.
Acquire full knowledge of the machine.
Read this manual carefully to understand: operation, safety devices and all necessary
precautions. All this is to allow safe use of the equipment.
Wear appropriate clothing for the job.
The operator must wear appropriate clothing, so as to prevent the occurrence of
unpleasant accidents.
Maintain the machine with care.
Machine operation
The machine must only be used by qualified personnel trained to use the machine by
authorized personnel.
Page 5 of 29
MACHINES AND
ACCESSORIES
fervi.com
2 SAFETY WARNINGS
2.1 General safety rules for machine tools
Risks related to Using the Machine
Do NOT underestimate the risks related to the use of the machine and stay focused on the
work you are carrying out.
Risks related to Using the Machine
Despite the implementation of all safety devices for safe use of the machine, it is necessary to
take note of all the accident prevention requirements highlighted in various parts of this
manual.
Risks related to Using the Machine
Every person who is responsible for the use and maintenance of the machine should first have
read the instruction manual, particularly the chapter dealing with safety.
It is recommended that the plant safety manager get written confirmation of the above.
Risks related to Using the Machine
During all work phases with the machine, you should proceed with great caution in
order to avoid damage to persons, to the property or to the machine itself.
Please use the machine only for its expected uses (drilling or tapping).
Don't tamper with the safety devices equipping the machine.
Risks related to Using the Machine
Before starting any work on the machine, the operator must wear the appropriate personal
protective equipment (PPE) such as gloves and eye protection.
Page 6 of 29
MACHINES AND
ACCESSORIES
fervi.com
1. Always check the efficiency and integrity of the machine.
2. Before connecting the machine to the mains make sure that the switch is in the rest
position.
3. Do not start the machine in an enclosed or poorly ventilated area, or in the presence of
a flammable and/or explosive atmosphere. Do not use the machine in damp and/or wet
locations, or those exposed to rain or humidity.
4. Before starting the machine, get used to ensuring that no remaining adjustment or
maintenance wrenches have remained inserted.
5. Keep the workplace tidy and free from hindrances; disorder causes accidents.
6. Make sure that the work environment is forbidden to children, non-employees and
animals.
7. Do not perform tasks on the machine other than those for which it was designed. Only
use the machine in the manner in which it was intended, as described in this instruction
manual.
8. Work without disturbances.
9. Work areas must be well lit.
10.Always wear eye protection and protective gloves while working. If dust is produced,
use the appropriate masks.
11.Wear appropriate clothing. Loose clothing, dangling jewellery, long hair, etc.., can get
caught in the moving parts, causing irreparable injury.
12.Replace worn and/or damaged parts, check that the guards and protection devices work
properly before operating. If necessary, have the machine checked by the service
support personnel. Use only original spare parts.
13.Cut the mains voltage supply to the machine when:
the machine is not being operated;
is left unattended;
you are performing maintenance or adjustment because the machine does not
work properly;
the power cable is damaged;
you are replacing its tool;
in case the machine is being moved to another location;
you are cleaning the machine.
14.Do not use the machine in areas with a risk of fire and / or explosion.
15.It is recommended that users of this publication, for maintenance and repair, have a
basic knowledge of mechanical principles and of repair technique procedures.
16.To stop the machine, always and only use the stop command (red button).
17.Do not leave the machine until the motor has completely stopped.
18.Management in charge of safety is to make sure that the staff responsible for
using the machine has read and understood this manual in its entirety.
19.The company safety manager is responsible for monitoring the company's risk
status according to Legislative Decree no. 81/08.
Page 7 of 29
MACHINES AND
ACCESSORIES
fervi.com
2.2 Safety rules for electrical machine equipment
Risks related to Using the Machine
1. Do not modify the electrical system in any way. Any attempt in this regard may
jeopardize the operation of electrical devices, thus causing malfunction or accident.
2. Work carried out in the electrical system of the machine must, therefore, be carried out
only by qualified and authorized personnel.
3. If one hears unusual noises, or feels something strange, immediately stop the machine.
Then carry out an inspection and, if necessary, perform any repairs as required.
1. Ensure supply voltage complies with the label and technical specifications (230 V / 50
Hz).
2. It is necessary to use a device for the automatic interruption of the power supply in
case of failure, which is to be coordinated with the machine's electrical system. For
more detailed information, contact a trusted electrician.
3. The mains power outlet should be bipolar grounded (10/16 A, 250 V), extension cables
must have sections that are the same or greater than the sections of the power cable
of the machine.
4. The power supply cable (and its possible extension cable) should never come in contact
with hot objects, sharp edges, wet or oiled surfaces.
5. The power cord should be checked regularly and before each use to check for signs of
damage or wear. If these are not in good condition, replace the cable.
6. Do not use the power cord to lift the machine or to remove the plug from the socket.
2.3 Technical support
For any problems or concerns, please contact, without hesitation the Customer Service
Department of your dealer, who has competent and specialized staff, specific equipment and
spare parts.
2.4 Other provisions
IT IS FORBIDDEN TO TAMPER WITH SAFETY DEVICES
The first thing to do when starting work is to check for the presence and integrity of the
protections and the operation of the safety devices.
If any defect is encountered do not use the machine!
Even more so, it is strictly forbidden to modify or remove guards, safety devices,
labels and indication signs.
Page 8 of 29
MACHINES AND
ACCESSORIES
fervi.com
3 TECHNICAL SPECIFICATIONS
Model Art. 0759
Weight (kg) 44
Rated voltage (V) 230
Frequency (Hz) 50
Power (W) 1,500
Motor speed (r/min) 2,950
Air flow rate (m3/h) 2,500
Noise emitted LpA(dB) 79
Size (mm) 840 x 560 x 1800
Page 9 of 29
Loading...