Fervi 0570 User And Maintenance Manual
USER AND
MAINTENANCE MANUAL
Axial Grinder Set with Sanding
Attachments
Art. 0570
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
fervi.com
HARDW
ARE
Page
2of13
FOREWORD
Read This Manual Before Operation
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
Reading this instruction manual is re
quired before operating any of the machinery. The
assurance of smooth operation and full compliance of machine performance is strictly
dependent on the rigorous application of all the instructions contained in this manual.
Operator Qualifications
Th
e workers responsible for using this machine must have all necessary information,
education and receive adequate training regarding safety, including:
a)
Conditions of use for the equipment;
b)
Foreseeable abnormal situations;
pursuant to art. 73 of Legislative
Decree no. 81/08.
We guarantee the Machine's conformity to specifications and technical instructions
described in the Manual on the date of issue, listed on this page; however, the
machine may be subject to potentially major technical changes in
the
fut
ure, without
the Manual being updated.
Therefore, contact FERVI for information about modifications that could be
implemented.
REV. 1
July 2013
fervi.com
HARDWARE
Page
3of13
IND
EX
1
GENERAL SAFETY INSTR
UCTIONS
................................
.............................
4
1.1
Risks Associated with the Work Area
................................
................................
............
4
1.2
Risks Associated with the Presence of Rotating and/or Moving Parts
...........................
4
1.3
Personal Protective Equipment
................................
................................
.....................
4
1.4
Technical Support
................................
................................
................................
.........
4
2
DESCRIPTION OF THE G
RIND
ER AND INTENDED USE
...............................
5
2.1
Technical Specifications
................................
................................
................................
5
2.2
Identification Plate
................................
................................
................................
.......
6
3
IMPROPER USES AND PR
ECAUTIONS
................................
........................
6
4
COMMISSIONING
................................
................................
......................
7
5
HOW TO USE
................................
................................
.............................
8
5.1
Attaching the Abrasive Tools
................................
................................
........................
8
5.2
Power On / Off
................................
................................
................................
............
10
6
MAINTENANCE AND CLEA
NING
................................
...............................
12
7
BILL OF MATERIALS AN
D SPARE PARTS
................................
..................
13
fervi.com
HARDW
ARE
Page
4of13
1
GENERAL SAFETY INSTR
UCTIONS
During use, maintain control of the tool.
The operators represent the most important aspect of safety. To better
protect against
the risk of injury, work cautiously and carefully.
When a fault / defect is detected, immediately disconnect the power supply cord from
the tool.
1.1
Risks Associated with the Work Area
1.
Keep unqualified people, children, etc. away from the wor
k environment and the
pneumatic tool.
2.
Only use to tool with proper lighting and visibility.
3.
Pay attention to unknown work environments and areas. The pneumatic tool is not
isolated from the power supply.
4.
Be especially careful to avoid contact with dust, ai
r jets or other pollutants. If
necessary, wear a dust mask.
5.
It is important to maintain a stable and secure position while working. Beware of air
hoses, which can cause you to trip and fall.
1.2
Risks Associated with the Presence of Rotating and/or Moving
Part
s
1.
Grab the pneumatic tool correctly, using the appropriate "torch" handle.
2.
Never touch t
he rotating parts of the tool,
particularly the ratchet bearing.
3.
Vibration, repetitive motions and uncomfortable positions may be harmful to your arms
and hands. Discon
tinue use of the ratchet if you experience symptoms of physical
discomfort, tingling and pain.
4.
While working, do not wear loose clothing or jewellery that could get caught in the
moving parts of the tool. Similarly, put hair back in a net or a cap.
1.3
Persona
l Protective Equipment
When using the pneumatic tool, always wear the following:
Safety shoes;
Work gloves;
Hearing protection (cap, earplugs, etc.);
Protective goggles.
1.4
Technical Support
For any problem or request for clarification, please do no
t hesitate to contact the support
service of the retailer from whom you purchased the product.
fervi.com
Loading...