Page 1
Not for
Reproduction
Page 2
Not for
Reproduction
Table of Contents:
Products Covered by This Manual......................................3
Identification Tag Location...................................................3
Product Identification Tag (Stamped).................................3
CE Identification Tag Markings............................................3
Operator Safety.....................................................................4
Operator Safety................................................................4
Safety Decals....................................................................9
CE Safety Icons..............................................................10
Safety Alert Symbol and Signal Words...........................10
Safety Interlock System..................................................10
Features and Controls........................................................11
Control Locations & Functions........................................11
Operation.............................................................................13
Before First-Time Use.....................................................13
Checks Before Starting...................................................13
Starting the Engine - Electric Start Models.....................13
Stopping the Mower........................................................14
Driving the Mower...........................................................14
Cutting Height Adjustment..............................................15
Mowing............................................................................15
Mowing Recommendations............................................15
Pushing the Unit by Hand...............................................17
Checking Tire Pressures................................................18
Checking / Adding Fuel...................................................18
Check Engine Oil Level..................................................18
Cleaning Debris from the Machine.................................18
Lubrication......................................................................18
Lubricating the Front Casters.........................................19
Check / Fill Transmission Oil..........................................20
Storage...........................................................................20
Maintenance Schedule........................................................21
Specifications......................................................................21
Warranty...............................................................................22
Warranty Statement........................................................22
2 ferrisindustries.com
Page 3
Not for
Reproduction
Thank you for purchasing this quality-built Ferris Commercial
Walk Behind Mower. We’re pleased that you’ve placed your
confidence in the Ferris brand. When operated and maintained
according to the manuals, your Ferris product will provide many
years of dependable service.
The manuals contain safety information to make you aware of
the hazards and risks associated with the unit and how to avoid
them. This Commercial Walk Behind Mower was designed to
be used as described in this operator's manual and operated
by trained professionals for finish cutting of established lawns
and is not intended for any other purpose. It is important that
you read and understand the instructions thoroughly before
attempting to start or operate this equipment. Save these original
instructions for future reference.
This product requires final assembly before use. Refer to the
setup guide for instructions on final assembly procedures. Follow
the instructions completely.
Products Covered by This Manual
The following products are covered by this manual:
5901441
The images in this document are representative, and are meant
to compliment the instructional copy they accompany. Your unit
may vary from the images displayed.
seen from the operator's position.
LEFT
and
RIGHT
are as
1
Product Identification Tag (Stamped)
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA.
All rights reserved.
Ferris is a trademark of Briggs & Stratton Power Products Group,
LLC
Briggs & Stratton Power Products Group, LLC.
5375 N. Main Street
Munnsville, NY 13409-4003
(800) 933-6175
ferrisindustries.com
Identification Tag Location
The product identification tags (A, Figure 1) can be found in the
locations shown.
PRODUCT REFERENCE DATA
Unit Model Number:
Unit Serial Number:
Mower Deck Model Number:
Mower Deck Serial Number:
Dealer Name:
Date Purchased:
ENGINE REFERENCE DATA
Engine Make:
Engine Model:
Engine Type/Spec:
Engine Code/Serial Number
When contacting your authorized dealer for replacement parts,
service, or information you MUST have these numbers.
The Illustrated Parts List for this machine can be downloaded
from ferrisindustries.com. Please provide model and serial
number when ordering replacement parts.
3
Page 4
Not for
Reproduction
CE Identification Tag Markings
Manufacturer's Identification NumberA.
Serial NumberB.
Manufacturer's AddressC.
CE Compliance LogoD.
Year of ManufactureE.
Sound Power in DecibelsF.
Maximum Engine Speed in Rotations per MinuteG.
Power Ratings in KilowattsH.
Mass of Unit in KilogramsI.
Operator Safety
The safety alert triangle in text signifies important cautions
or warnings which must be followed.
Operating Safety
Congratulations on purchasing a superior-quality piece of lawn
and garden equipment. Our products are designed and
manufactured to meet or exceed all industry standards for safety.
Do not operate this machine unless you have been trained.
Reading and understanding this operator’s manual is a way to
train yourself.
Power equipment is only as safe as the operator. If it is misused,
or not properly maintained, it can be dangerous! Remember,
you are responsible for your safety and that of those around
you.
Use common sense, and think through what you are doing. If
you are not sure that the task you are about to perform can be
safely done with the equipment you have chosen, ask a
professional: contact your local authorized dealer.
WARNING
U.S.A. Models: The engine exhaust from this product
contains chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm.
WARNING
Battery posts, terminals, and related accessories contain
lead and lead compounds, chemicals known to the State
of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
Operator Safety
Read these safety rules and follow them closely. Failure to obey
these rules could result in loss of control of the unit, severe
personal injury or death to you, or bystanders, or damage to
property or equipment. This mowing deck is capable of
amputating hands and feet and throwing objects.
Read the Manual
The operator’s manual contains important safety information
you need to be aware of BEFORE you operate your unit as well
as DURING operation.
Safe operating techniques, an explanation of the product’s
features and controls, and maintenance information is included
to help you get the most out of your equipment investment.
Be sure to completely read the Safety Rules and Information
found on the following pages. Also completely read the
Operation section.
4 ferrisindustries.com
Page 5
Not for
Reproduction
Children
sure to clean up the area to be mowed and remove objects that
could be thrown by the blade BEFORE you start mowing.
Do not operate this unit without the entire grass catcher or
discharge guard (deflector) in place.
Also, do not allow anyone in the area while the unit is running!
If someone does enter the area, shut the unit off immediately
until they leave.
Tragic accidents can occur with children. Do not allow them
anywhere near the area of operation. Children are often attracted
to the unit and mowing activity. Never assume that children will
remain where you last saw them. If there is a risk that children
may enter the area where you are mowing, have another
responsible adult watch them.
Slope Operation
You could be seriously injured if you use this unit on too steep
of a slope. Using the unit on a slope that is too steep where you
do not have adequate footing and unit traction (and control) can
cause you to lose control and possibly slip and fall or roll the
unit over.
Moving Parts
This equipment has many moving parts that can injure you or
someone else. However, if you stay in the operator zone (area
behind the handles and controls), and follow the safety rules in
this operator’s manual, the unit is safe to operate.
The mower deck has spinning mower blades that can amputate
hands and feet. Do not allow anyone near the unit while it is
running! Keep safety devices (guards, shields, and switches)
in place and working.
To help you, the operator, use this equipment safely, it is
equipped with an operator-present safety system. Do NOT
attempt to alter or bypass the system. See your dealer
immediately if the system does not pass all the safety interlock
system tests found in this manual.
Always mow across slopes, not up and down (you could slip
and fall.)
Also, note that the surface you are on can greatly impact your
ability to safely operate this machine. Wet grass or soft soil can
seriously affect your footing and traction of the unit. Do not
operate on slopes that are slippery, wet, or have soft soil.
Thrown Objects
This unit has spinning mower blades. These blades can pick
up and throw debris that could seriously injure a bystander. Be
Fuel and Maintenance
Always disengage all drives, shutoff the engine and remove the
key before doing any cleaning, refueling or servicing.
Gasoline and its vapors are extremely flammable. Do not smoke
while operating or refueling. Do not add fuel while engine is hot
or running. Allow engine to cool for at least 3 minutes prior to
adding fuel.
Do not add fuel indoors, in an enclosed trailer, garage or other
enclosed area that is not well ventilated. Gasoline spills should
be cleaned up promptly and before operation begins.
Gasoline should be stored only in sealed containers approved
for fuel.
5
Page 6
Not for
Reproduction
Proper maintenance is critical to the safety and performance of
your unit. Keep the unit free of grass, leaves and excess oil. Be
sure to perform the maintenance procedures listed in this
manual, especially periodically testing the safety system.
Enclosed Areas
Only operate this unit outdoors and away from unventilated
areas such as inside garages or enclosed trailers. The engine
emits poisonous carbon monoxide gas and prolonged exposure
in an enclosed area can result in serious injury or death.
Training
• Read, understand, and follow all instructions in the manual
and on the unit before starting. If the operator(s) or
mechanic(s) can not read English it is the owner’s
responsibility to explain this material to them.
• Become familiar with the safe operation of the equipment,
operator controls, and safety signs.
• All operators and mechanics should be trained. The owner
is responsible for training the users.
• Only allow responsible adults, who are familiar with the
instructions, to operate the unit.
• Never let children or untrained people operate or service
the equipment. Local regulations may restrict the age of the
operator.
• The owner/user can prevent and is responsible for accidents
or injuries occurring to themselves, other people or property.
• Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability to
operate the riding mower safely enough to protect
themselves and others from serious injury.
Preparation
• Evaluate the terrain to determine what accessories and
attachments are needed to properly and safely perform the
job. Use only accessories and attachments approved by
the manufacturer.
• Wear appropriate clothing including safety shoes, safety
glasses and ear protection. Long hair, loose clothing or
jewelry may get tangled in moving parts.
• Inspect the area where the equipment is to be used and
remove all objects such as rocks, toys and wire, which can
be thrown by the machine.
• Use extra care when handling gasoline and other fuels.
They are flammable and vapors are explosive.
• Use only an approved container.
• Never remove fuel cap or add fuel with the engine running.
Allow engine to cool before refueling. Do not smoke.
• Never refuel or drain the machine indoors.
• Check that operator’s presence controls, safety switches
and shields are attached and functioning properly. Do not
operate unless they are functioning properly.
Operation
• Never run an engine in an enclosed area.
• Mow only in the daylight or with good artificial light, keeping
away from holes and hidden hazards.
• Be sure all drives are in neutral and parking brake is
engaged before starting engine. Only start engine from the
operator’s position.
• Be sure of your footing while using pedestrian controlled
equipment, especially when backing up. Walk, don’t run.
Reduced footing could cause slipping.
• Slow down and use extra care on hillsides. Be sure to travel
in the recommended direction on hillsides. Turf conditions
can affect the machines stability. Use caution when
operating near drop-offs.
• Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while traveling in reverse.
• Be aware of the mower discharge direction and do not point
it at anyone. Do not operate the mower without either the
entire grass catcher or the deflector in place.
• Slow down and use caution when making turns and when
changing directions on slopes.
• Never raise deck with the blades running.
• Never leave a running unit unattended. Always disengage
the PTO, set the parking brake, stop the engine, and remove
keys before dismounting. Keep hands and feet away from
the cutting units.
• Turn off the PTO switch to disengage the blades when not
mowing.
• Never operate with guards not securely in place. Be sure
all interlocks are attached, adjusted properly and functioning
properly.
• Never operate with the discharge deflector raised, removed
or altered, unless using a grass catcher.
• Do not change the engine governor setting or over-speed
the engine.
• Stop on level ground, lower implements, disengage drives,
engage parking brake, shut off engine before leaving the
operator’s position for any reason including emptying the
grass catchers or unclogging the chute.
6 ferrisindustries.com
Page 7
Not for
Reproduction
• Stop equipment and inspect blades after striking objects or
abnormal vibration occurs. Make necessary repairs before
resuming operations.
• Keep hands and feet away from the cutting units.
• Look behind and down before backing up to be sure of a
clear path.
• Never carry passengers and keep pets and bystanders
away.
• Do not operate the unit while under the influence of alcohol
or drugs.
• Slow down and use caution when making turns and crossing
roads and sidewalks. Stop blades if not mowing.
• Use care when loading or unloading the machine into a
trailer or truck.
• Use care when approaching blind corners, shrubs, trees or
other objects that may obscure vision.
• To reduce fire hazard, keep unit free of grass, leaves &
excess oil. Do not stop or park over dry leaves, grass or
combustible materials.
WARNING
It is a violation of California Public Resource Code, Section
4442, to use or operate the engine on any forest-covered,
brush-covered or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section
4442, maintained in effective working order. Other states or
federal jurisdictions may have similar laws. Contact an
Authorized Service Dealer to obtain a spark arrester designed
for the exhaust system installed on this engine.
• OSHA regulations may require the use of hearing protection
when exposed to sound levels greater than 85 dBA for an
8 hour time period.
CAUTION
This machine produces sound level in excess of 85 dBA at
the operator's ear and can cause hearing loss through
extended periods of exposure.
Wear hearing protection when operating this machine.
WARNING
Operating on a steep slope can cause sliding and loss of
steering, control, and rollover.
Select slow ground speed before driving onto a slope. Use
extra caution when operating on slopes with rear mounted
grass catchers.
Mow across the face of slopes, not up and down, use caution
when changing directions and DO NOT START OR STOP
ON A SLOPE.
Do:
• Mow across slopes, not up and down.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Uneven terrain could
overturn the unit. Tall grass can hide obstacles.
• Use slow speed. Choose a slow speed so that you will not
have to stop or change speed while on the slope.
• Use extra care with grass catchers or other attachments.
These can change the stability of the unit.
• Keep all movement on the slopes slow and gradual. Do not
make sudden changes in speed or direction.
• See your authorized dealer for recommendations of
available weights to improve stability.
Do not:
• Avoid starting, stopping, or turning on a slope. If tires lose
traction (i.e. machine stops forward motion on a slope),
disengage the blade(s) (PTO) and drive slow off the slope.
• Do not turn on slopes unless necessary, and then, turn
slowly.
• Do not mow near drop-offs, ditches, or embankments. The
operator could lose footing or balance or mower could
suddenly turn over if a wheel is over the edge of a cliff or
ditch, or if an edge caves in.
• Do not mow on wet grass. Reduced footing or traction could
cause sliding.
• Do not mow excessively steep slopes.
• Do not use grass catcher on steep slopes.
Slope Operation
Slopes are a major factor related to loss-of-control and tip-over
accidents, which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not drive on it.
Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the unit
and the mowing activity. Never assume that children will remain
where you last saw them.
• Keep children out of the mowing area and under the
watchful care of another responsible adult.
• Be alert and turn unit off if children enter the area.
• Before and during reverse operation, look behind and down
for small children.
• Never allow children to operate the unit.
7
Page 8
Not for
Reproduction
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
Emissions
• Engine exhaust from this product contains chemicals known,
in certain quantities, to cause cancer, birth defects, or other
reproductive harm.
• Look for the relevant Emissions Durability Period and Air
Index information on the engine emissions label.
Ignition Systems (Gasoline Models)
• This spark ignition system complies with Canadian
ICES-002.
Service and Maintenance Safety
WARNING
Amputation and crushing hazard
Specific steps must be taken in order to perform service and
maintenance procedures safely.
Read and follow all the applicable safety and instructional
messages in this manual.
Always disengage the mower blades, set the parking brake,
turn the engine OFF, remove the ignition key, and wait for all
movement to stop prior to performing service and maintenance
procedures.
Always disconnect the spark plug wire(s) and fasten it away
from the plug before beginning any maintenance or service
procedures on order to prevent accidental ignition.
Safe Handling of Gasoline
DANGER
Fire and explosion hazard
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other sources
of ignition.
• Use only approved gasoline containers.
• Never remove the gas cap or add fuel with the engine
running. Allow the engine to cool before refueling.
• Never fuel the machine indoors.
• Never store the machine or fuel container where there is
an open flame, spark, or pilot light such as near a water
heater or other appliance.
• Never fill containers inside a vehicle or on a truck bed with
a plastic bed liner. Always place containers on the ground
away from your vehicle before filling.
• Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then refuel
such equipment on a trailer with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do
not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never over-fill the fuel tank. Replace gas cap and tighten
securely.
• Use extra care in handling gasoline and other fuels. They
are flammable and vapors are explosive.
• If fuel is spilled, do not attempt to start the engine but move
the machine away from the area of spillage and avoid
creating any source of ignition until fuel vapors have
dissipated.
• Replace all fuel tank caps and fuel container caps securely.
Maintenance and Storage
• Always observe safe refueling and fuel handling practices
when refueling the unit after transportation or storage.
• Always follow the engine manual instructions for storage
preparations before storing the unit for both short and long
term periods.
• Always follow the engine manual instructions for proper
start-up procedures when returning the unit to service.
• Never store the machine or fuel container inside where
there is an open flame, such as in a water heater. Allow
unit to cool before storing.
• Shut off fuel while storing or transporting. Do not store fuel
near flames or drain indoors.
• Keep all hardware, especially blade attachment bolts, tight
and keep all parts in good working condition. Replace all
worn or damaged decals.
• Never tamper with safety devices. Check their proper
operation regularly.
• Disengage drives, lower implement, set parking brake, stop
engine and remove key or disconnect spark plug wire. Wait
for all movement to stop before adjusting, cleaning or
repairing.
• Clean grass and debris from cutting units, drives, mufflers,
and engine to prevent fires. Clean up oil or fuel spillage.
• Let engine cool before storing and do not store near flame.
• Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
• Park machine on level ground. Never allow untrained
personnel to service machine.
• Use jack stands to support components when required.
• Carefully release pressure from components with stored
energy.
• Disconnect battery or remove spark plug wire before making
any repairs. Disconnect the negative terminal first and the
positive last. Reconnect positive first and negative last.
8 ferrisindustries.com
Page 9
Not for
Reproduction
• Use care when checking blades. Wrap the blade(s) or wear
gloves, and use caution when servicing them. Only replace
blades. Never straighten or weld them.
• Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
• Charge batteries in an open well ventilated area, away from
spark and flames. Unplug charger before connecting or
disconnecting from battery. Wear protective clothes and
use insulated tools.
• Grass catcher components are subject to wear, damage,
and deterioration, which could expose moving parts or allow
objects to be thrown. Frequently check components and
replace with manufacturer’s recommended parts, when
necessary.
• Check brake operation frequently. Adjust and service as
required.
• Use only factory authorized replacement parts when making
repairs.
• Always comply with factory specifications on all settings
and adjustments.
• Only authorized service locations should be utilized for
major service and repair requirements.
• Never attempt to make major repairs on this unit unless you
have been properly trained. Improper service procedures
can result in hazardous operation, equipment damage and
voiding of manufacturer’s warranty.
• Units with hydraulic pumps, hoses, or motors: WARNING:
Hydraulic fluid escaping under pressure may have sufficient
force to penetrate skin and cause serious injury. If foreign
fluid is injected into the skin it must be surgically removed
within a few hours by a doctor familiar with this form of injury
or gangrene may result. Keep body and hands away from
pin holes or nozzles that eject hydraulic fluid under high
pressure. Use paper or cardboard, and not hands, to search
for leaks. Make sure all hydraulic fluid connections are tight
and all hydraulic hoses and lines are in good condition
before applying pressure to the system. If leaks occur, have
the unit serviced immediately by your authorized dealer.
• WARNING: Stored energy device. Improper release of
springs can result in serious personal injury. Springs should
be removed by an authorized technician.
Part Number: 5103934 - Decal, Main Safety, CE WBA
Part Number: 5102420 - Decal, Danger, Mower Deck, ANSI ExpB
Part Number: 5102457 - Decal, Danger Discharge, ANSI ExpC
Safety Decals
Before operating your unit, read the safety decals. The cautions
and warnings are for your safety. To avoid a personal injury or
damage to the unit, understand and follow all safety decals.
WARNING
If any safety decals become worn or damaged, and cannot
be read, order replacement decals from your local dealer.
Part Number: 5104566 - Decal, Control Panel, WKB, Man/Elec StartD
Battery DecalE
9
Page 10
Not for
Reproduction
CE Safety Icons
Warning: Read Operator’s Manual -
Read and understand the operator’s
manual before using this machine.
Danger: Fire Hazard - Keep the unit
free of grass, leaves and excess oil.
Do not add fuel while engine is hot or
running. Stop engine and allow to cool
for at least 3 minutes prior to adding
fuel. Do not add fuel indoors, in an
enclosed trailer, garage or other
enclosed areas. Clean up spilled fuel.
Do not smoke while operating this
machine.
Danger: Thrown Objects - This
machine is capable of thrown objects
and debris. Keep bystanders away.
Danger: Dismemberment - This
mower deck can amputate limbs. Keep
hands and feet away from blades.
Danger: Machine Rollover -
Operating on steep slops can cause
sliding and loss of steering, control and
rollover.
Danger: Thrown Objects Hazard -
Do not mow without discharge chute
or entire grass catcher in place.
Safety Alert Symbol and Signal Words
The safety alert symbol indicates a potential personal injury
hazard. A signal word (DANGER, WARNING, or CAUTION) is
used with the alert symbol to designate a degree or level of
hazard seriousness. A safety symbol may be used to represent
the type of hazard. The signal word NOTICE is used to address
practices not related to personal injury.
DANGER indicates a hazard which, if not avoided,
in death or serious injury.
WARNING indicates a hazard which, if not avoided,
result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
result in minor or moderate injury.
NOTICE
product.
indicates an action that could result in damage to the
will
result
could
could
Safety Interlock System
This unit is equipped with safety interlock switches. These safety
systems are present for your safety, do not attempt to bypass
safety switches, and never tamper with safety devices. Check
their operation regularly.
Operational SAFETY Checks
Test 1 - Engine should NOT crank if:
• Forward speed control lever is not in the NEUTRAL position.
Test 2 - Engine SHOULD crank if:
Danger: Amputation and Thrown
Objects Hazard - To avoid injury from
rotating blades, stay clear of the deck
edge and keep others away.
Warning: Fire Hazard - Keep children,
open flames and sparks away from the
battery, which could ignite explosive
gases.
Warning: Sulfuric acid can cause
blindness or severe burns - Always
wear safety goggles or a face shield
when working on or near a battery.
Warning: Batteries produce
explosive gases - Read and
understand the Operator’s Manual
before using this machine.
Important: Do not discard a battery
in the trash - Contact local authorities
for disposal and/or recycling of
batteries.
• Forward speed control lever is in the NEUTRAL position.
Test 3 - Engine should SHUT OFF if:
• Operator releases the operator presence handles while the
forward speed control lever is not in the NEUTRAL position.
Test 4 - PTO Switch (blades) should SHUT OFF if:
• If the PTO switch is ON and the operator releases the
operator presence handles, OR
• The operator presses the PTO switch down to the OFF
position.
Test 5 - PTO Switch (blades) SHOULD turn on if:
• Operator depresses the operator presence handles and the
PTO switch is pulled up to the ON position.
Test 6 - Blade Brake Check:
Mower blades and mower drive belt should come to a complete
stop within seven (7) seconds after electric PTO switch is turned
OFF (or operator releases the operator presence handles). If
the mower drive belt does not stop within seven (7) seconds,
see your dealer.
10 ferrisindustries.com
Page 11
Not for
Reproduction
NOTE: Once the engine has been stopped, the forward speed
control lever must be returned to the NEUTRAL position, the
parking brake should be engaged, the operator presence
handles should be depressed and the PTO switch should be in
the OFF position in order to start the engine.
WARNING
If the unit does not pass a safety test, do NOT operate it. See
your authorized dealer. Under no circumstance should you
attempt to defeat the purpose of the safety interlock system.
Features and Controls
Control Locations & Functions
The information below briefly describes the function of individual
controls. Starting, stopping, driving, and mowing require the
combined use of several controls applied in specific sequences.
To learn what combination and sequence of controls to use for
various tasks see the
Operation
section.
Operator Presence Handles: These handles are a major factor
in the safety interlock system of the mower. Both handles are
tied together so depressing one handle depresses both. The
operator must depress the handles in order to activate the PTO
(Power Take Off) switch.
If the operator presence handles are released and the forward
speed control lever is in the NEUTRAL position and the PTO
switch is engaged, the mower blades will stop, but the engine
will remain running.
If the operator presence handles are released and the forward
speed control lever is NOT in the NEUTRAL position, the engine
will stop (with or without the PTO engaged).
Forward Speed Control Lever / Drive Levers: These levers
control the ground speed and direction of travel of the mower.
Control NameIcon
Forward Speed Control Lever
2
Control NameCallout
Operator Presence HandlesA
Forward Speed Control LeverB
Drive LeversC
Hour MeterD
Forward Speed IndicatorE
Ignition SwitchF
ChokeG
Throttle ControlH
PTO (Power Take Off) SwitchI
Neutral Return PedalsJ
Left Drive Lever
Right Drive Lever
Control PositionIcon
Forward
Neutral
Reverse
The forward speed control lever controls the forward ground
speed of both drive wheels. The forward speed control lever
cannot be moved forward out of the NEUTRAL position if the
parking brake lever is engaged.
The left drive lever controls the steering and reverse ground
speed of the left drive wheel. The right drive lever controls the
steering and reverse ground speed of the right drive wheel.
Squeeze both reverse speed control levers evenly to move in
reverse.
See the
instructions.
hours the PTO has been engaged. The hour meter has a self
contained power source so the total hours are always visible.
Driving the Mower
Hour Meter: The hour meter measures the number of
section for proper steering
11
Page 12
Not for
Reproduction
Forward Speed Indicator: The purpose of the Forward Speed
Indicator is to help the operator quickly reset the forward speed
control of the mower to a preferred driving speed.
Icon
Forward Speed IndicatorControl Name
The neutral return pedals provide a hands-free return to neutral.
The pedals are used in conjunction with the drive levers to
properly stop the machine. The two pedals are connected
together so depressing one depresses both.
The operator must fully depress the neutral pedal downwards
to return the mower to neutral. The mower must be in the neutral
position to start the engine.
The forward speed indicator works in conjunction with the
Forward Speed Control Lever and the Neutral Return Pedal.
The further the Forward Speed Control Lever is pressed forward
the further the Forward Speed Indicator travels to the right.
When the Forward Speed Control Lever is pulled rearward or
the Neutral Return Pedal is being depressed the Forward Speed
Indicator travels to the left
Ignition Switch: The ignition switch starts and stops the engine,
it has three positions:
OFF
RUN
START
NOTE: Never leave the ignition switch in the RUN position with
the engine stopped—this drains the battery.
Choke: Close the choke for cold starting. Open the choke
once the engine starts. A warm engine may not require choking.
Pull the knob UP to close the choke. Push the knob DOWN to
open the choke.
Stops the engine and
shuts off the electrical
system.
Allows the engine to run
and powers the electrical
system.
Cranks the engine for
starting.
See the
of the neutral return pedals.
Stopping the Mower
3
section for operating instructions
Throttle Control: The throttle controls engine speed. Move the
throttle forward to increase engine speed and back to decrease
engine speed. Always operate at FULL throttle when mowing.
Fast throttle speed.
Slow throttle speed.
PTO (Power Take Off) Switch: The PTO switch engages
and disengages the mower blades. Pull UP on the switch to
engage, and push DOWN to disengage.
Neutral Return Pedals:
Control NameIcon
Neutral Return Pedals
Control NameCallout
Parking Brake LeverA
Fuel Tank CapB
Transmission Oil FillC
Transmission Release LeversD
Parking Brake: Pull the parking brake lever rearward and
up to engage the parking brake. Move the lever fully forward
and down to disengage the parking brake.
Releases the parking brake.Disengage
Locks the parking brake.Engage
Fuel Tank Cap: To remove the cap, turn counter-clockwise.
Transmission Oil Fill: Transmission oil is added through the
hydraulic oil reservoirs. It also serves as extra holding capacity
for oil as the transmissions heat up and the hydraulic oil
12 ferrisindustries.com
Page 13
Not for
Reproduction
expands. See
and fill procedures.
Transmission Release Levers:
This unit is equipped with two transmission release levers. The
transmission release levers deactivate the transaxle so that the
unit can be pushed by hand. Both transmission release levers
must be in the same position whether you are driving the unit
or pushing it by hand. See
operational information.
Check / Fill Transmission Oil
Control NameIcon
Transmission Release Levers
Pushing the Unit by Hand
for oil level check
for
Operation
Before First-Time Use
• Be sure to read all information in the Safety and Operation
sections before attempting to operate this unit.
• Become familiar with all of the controls and how to stop the
unit.
• Operate in an open area without engaging the PTO to
become accustomed to the unit.
WARNING
Read the operator's manual before attempting to operate
the machine.
If you do not understand how a specific control functions, or
have not yet thoroughly read the Features and Controls
section, do so now.
Do not attempt to operate the mower without first becoming
familiar with the location and function of all controls.
Checks Before Starting
4
• Check that crankcase is filled to the full mark on the dipstick
(A, Figure 4). See the engine Operator’s Manual for engine
oil dipstick location, oil fill instructions, and oil
recommendations.
• Make sure all nuts, bolts, screws, and pins are in place and
tight.
• Check the hydraulic oil tanks (B) and make sure that the oil
level is up to the FULL COLD mark.
• Fill the fuel tank (C) with fresh fuel. Refer to engine manual
for fuel recommendations.
Starting the Engine - Electric Start Models
WARNING
If you do not understand how a specific control functions,
or have not yet thoroughly read the
section, do so now.
Features & Controls
WARNING
• Before leaving the operator's position for any reason,
engage the parking brake, disengage the PTO, stop the
engine and remove the key.
• To reduce fire hazard, keep the engine and mower free
of grass, leaves and excess grease. Do NOT stop or park
unit over dry leaves, grass or combustible materials.
• Gasoline is highly flammable and must be handled with
care. Never fill the tank when the engine is still hot from
recent operation. Do NOT allow open flame, smoking or
matches in the area. Avoid over-filling and wipe up any
spills.
Do NOT attempt to operate the unit without first becoming
familiar with the location and function of ALL controls.
1. Engage the parking brake and make sure the PTO switch
is disengaged and the forward speed control lever is in the
NEUTRAL position.
2. Set the engine throttle control to FULL throttle position.
Then fully close the choke by pulling the knob OUT fully.
NOTE: A warm engine may not require choking.
3. Insert the key into the ignition switch and turn it to the
START position.
4. After the engine starts, gradually open the choke (push
knob down fully). Reduce to half throttle speed and allow
to warm up. Warm up the engine by running it for at least
13
Page 14
Not for
Reproduction
a minute before engaging the PTO switch or driving the
mower.
5. After warming the engine, ALWAYS operate the unit at
FULL THROTTLE when mowing.
In the event of an emergency the engine can be stopped
by simply turning the ignition switch to STOP. Use this
method only in emergency situations. For normal engine
shut down follow the procedure given in STOPPING THE
MOWER
Stopping the Mower
or unloading from a truck or trailer, partial throttle should be
used to slow the reaction time of the controls and reduce noise.
Practice maneuvering the machine at a slow engine speed on
level ground with the PTO switch in the “OFF” position until you
are familiar with the controls.
To Move Forward and Set Forward Speed
1. Disengage the parking brake.
2. Gently move the forward speed control lever (A, Figure 6,
inset 1) forward until desired speed is achieved.
1. Gently squeeze both drive levers (A, Figure 5) evenly to
stop the unit.
5
2. Once the unit is stopped, firmly depress the neutral return
pedal (B) to place the transmission in neutral.
3. Disengage the PTO by pushing down on the PTO switch
(C).
4. Engage the parking brake by pulling the parking brake lever
(D) fully up and rearward towards the handle bars.
5. Move the throttle control (E) to mid-throttle position and turn
the ignition key (F) to OFF. Remove the key.
6
To Move Backward
1. Disengage the parking brake.
2. Gently squeeze both drive levers (B, inset 2) evenly, until
desired speed is achieved.
To Slow or Stop Machine
Driving the Mower
Before attempting to drive the mower make sure you have read
the
Features and Controls
and function of the controls.
The hydrostatic transmission has an infinite number of speeds
between full speed forward and reverse, with the faster speeds
being achieved by moving the forward speed control lever and
drive levers farthest in their directions of travel.
For normal use, the throttle should be kept fully open and the
ground speed of the machine determined by the forward speed
control lever. When transporting the machine or when loading
14 ferrisindustries.com
section and understand the location
1. Gently squeeze both drive levers evenly to slow the
machine.
2. Continuing to squeeze the drive levers will stop the machine.
3. Once the machine is stopped, firmly depress the neutral
return pedal to place the transmissions in neutral.
4. Engage the parking brake.
NOTE: Continuing to squeeze the drive levers after the machine
is stopped, will cause the machine to move in reverse.
Turning the Machine
Note: Always reduce speed in a turn.
Page 15
Not for
Reproduction
Turning Left:
Gently squeeze the left drive lever (C, inset 3). A sharp or gentle
turn is determined by the amount of force applied to the drive
lever.
Turning Right:
Gently squeeze the right drive lever (D, inset 4). A sharp or
gentle turn is determined by the amount of force applied to the
drive lever.
Cutting Height Adjustment
To adjust the cutting height:
1. Use Figure 7 and the Cut Height Indication Chart to
determine the correct mounting holes for the desired cutting
height.
in all four deck lift shafts for the mower deck to have a
level cut.
Mowing
Before mowing, set the cutting height as described in
Height Adjustment
1. Engage the parking brake. Make sure that the PTO switch
is disengaged and the forward speed control lever is in the
neutral position.
2. Start the engine (see
3. Set the throttle to the ½ throttle position.
NOTE: It is best practice to engage the PTO with the throttle
set at the minimum throttle position necessary to engage the
deck drive system without stalling the engine.
.
Starting the Engine
).
Cutting
7
Cut Height Indication Chart
Cutting HeightHole Number
1.5" (3.8 cm)1
2.0" (5.1 cm)2
2.5" (6.4 cm)3
3.0" (7.6 cm)4
3.5" (8.9 cm)5
4.0" (10.2 cm)6
4.5" (11.4 cm)7
2. Remove the hair pins (A, Figure 7) from the deck lift shafts
(C).
3. Use the deck handle (B) and either raise or lower the cutter
deck to the desired cutting height. Re-install the hair pins
in the hole for the desired cutting height.
4. Repeat the process for the other side of the machine. The
hair pins must be installed in the same numbered hole
4. Engage the PTO by pulling up the PTO switch.
5. Move the throttle to the "FAST" position and begin mowing.
6. Release the parking brake and begin mowing.
7. When finished, reduce throttle speed so that the engine
idles and push the PTO switch down to shut off the PTO.
8. Stop the engine. See
Stopping the Mower
.
Mowing Recommendations
Several factors can affect how well your machine cuts grass,
Following proper mowing recommendations can improve the
performance and life of your machine.
Height of Grass
Often cutting height is a matter of personal preference. Typically,
you should mow the grass when it is between three and five
inches high. The proper cutting height range for a specific lawn
will depend upon several factors, including the type of grass,
the amount of rainfall, the prevailing temperature, and the lawn’s
overall condition.
Cutting the grass too short causes weak, thin grass plants,
which are easily damaged by dry periods and pests. Cutting
too short is often more damaging than allowing the grass to be
slightly higher.
Letting grass grow a bit longer—especially when it is hot and
dry—reduces heat build-up, preserves needed moisture and
protects the grass from heat damage and other problems.
However, allowing grass to grow too high can cause thin turf
and additional problems.
Cutting off too much at one time shocks the plant’s growth
system and weakens the grass plants. A good rule of thumb
is the 1/3 rule: to cut no more than one third of the grass
height, and never more than 1 inch at a time.
15
Page 16
Not for
Reproduction
8
The amount of grass you are able to cut in one pass is also
effected by the type of mowing system you are using (for
example, broadcasting with side discharge decks can process
a much larger volume of grass than mulching does).
Tall grass requires incremental cutting. For extremely tall
grass, set the cutting height at maximum for the first pass (A,
Figure 9), and then reset it to the desired height and mow a
second (B) or third time.
Don’t cover the grass surface with a heavy layer of clippings.
Consider using a grass collection system and starting a compost
pile.
• Mow at time of day when the grass is cool and dry. Late
afternoon or early evening often provide these ideal mowing
conditions.
• Avoid mowing after rain or even heavy dew, and never
mulch when the grass is wet (moist grass does not mulch
well, and clumps beneath the mower deck).
Mowing Patterns
Always start mowing on a smooth, level area.
The size and type of area to be mowed will determine the best
mowing pattern to use. Obstructions such as trees, fences and
buildings, and conditions such as slopes and grades must also
be considered.
• Cut long straight strips overlapping slightly.
• Where possible, change patterns occasionally to eliminate
matting, graining or a corrugated appearance.
• For a truly professional cut, mow across the lawn in one
direction, then re-cut the lawn by mowing perpendicular to
the previous cut.
NOTE: Always operate the engine at FULL THROTTLE when
mowing.
If you hear the engine slowing down, you are mowing too
fast—using a slower ground speed will improve the cutting
efficiency of the blades and prevents many common cutting
problems. Use an appropriate ground speed for the thickness
and height of the grass you are cutting (3rd gear or slower for
manual gear models). If you hear the engine slowing down you
are mowing too fast, use a slower ground speed.
9
When and How Often to Mow
The time of day and condition of the grass greatly affect the
results you’ll get when mowing. For the best results, follow these
guidelines:
• Mow when the grass is between three and five inches high.
• Mow with sharp blades. Short clippings of grass one inch
or shorter decompose more quickly than longer blades.
Sharp mower blades cut grass cleanly and efficiently,
preventing frayed edges which harm the grass.
10
Where possible, make one or two passes around the outside
of the area discharging the grass INTO the lawn to keep the cut
grass off fences and walks.
16 ferrisindustries.com
Page 17
Not for
Reproduction
11
The remainder of the mowing should be done in the opposite
direction so that the clippings are dispersed OUT onto the area
of lawn previously cut.
Mowing Methods
Broadcast Mowing
Broadcasting, or side-discharging, disperses fine clippings
evenly over the entire lawn. Many golf courses use this method.
Your mower has a deep dish deck to allow freer circulation of
clippings so they are broadcast evenly over the lawn.
Engine Speed & Ground Speed for Broadcasting:
Always operate the engine at full throttle when mowing. If you
hear the engine slowing down, you are mowing too fast—using
a slower ground speed will improve the cutting efficiency of the
blades and prevents many common cutting problems.
ALWAYS use an appropriate ground speed for the thickness
and height of the grass you are cutting (3rd gear or slower for
manual gear models). If you hear the engine slowing down you
are mowing too fast, use a slower ground speed.
How Much Grass to Cut Off When Broadcasting:
growth, and often wetter conditions are more suitable for
broadcasting (side-discharging) or grass bagging operation.
Engine Speed & Ground Speed for Mulching:
Use full engine throttle matched with a slow ground speed so
that clippings will be finely cut. Ground speed while mulching
should be HALF of the speed that would be used when
broadcasting (side discharging) under similar conditions. Since
mulching requires more horsepower than broadcasting, using
a slower ground speed is vitally important for proper mulching
operation.
How Much Grass to Mulch:
The best mulching action typically results from cutting only the
top ½ inch to 3/4 inch of grass blade. This provides short
clippings which decompose properly (much more quickly than
longer clippings). The ideal cutting height will vary with climate,
time of year, and quality of your lawn. We recommend that you
experiment with both the cutting height and ground speed until
you achieve the best cut. Start with a high cutting height and
using progressively lower settings until you find a cutting height
that is matched to your mowing conditions and preferences.
Pushing the Unit by Hand
NOTICE
Towing the units while the transmissions are engaged will
cause transmission damage. Do NOT use another vehicle to
push or pull this unit.
This unit is equipped with two transmission release levers.
1. Depress the neutral return pedals to return the transmissions
to NEUTRAL, disengage the PTO, engage the parking
brake, turn the ignition switch to OFF, and remove the key.
2. Locate the transmission release levers (A, Figure 12) by
the rear wheels of the unit.
Mow when the grass is 3-5 inches long. Do not cut the grass
shorter than 2 to 2-1/2 inches. Do not cut off more that 1 inch
of grass in a single pass.
Mulching
Mulching consists of a mower deck which cuts and re-cuts
clippings into tiny particles and which then blows them down
INTO the lawn. These tiny particles decompose rapidly into
by-products your lawn can use. UNDER PROPER
CONDITIONS, your mulching mower will virtually eliminate
noticeable clippings on the lawn surface.
NOTE: When mulching under heavy cutting conditions, a
rumbling sound may be present and is normal.
Mulching Requires EXCELLENT Mowing Conditions:
Mulching mowers cannot function properly if the grass is wet,
or if the grass is simply to high to cut. Even more than normal
mowing, mulching requires that the grass be dry and the
appropriate amount is cut.
Do not use the mower as a mulching mower during the first two
or three mowings in the spring. The long grass blades, quick
17
Page 18
Not for
Reproduction
12
Checking / Adding Fuel
WARNING
Fuel and its vapors are extremely flammable and
explosive.
Fire or explosion can cause severve burns or death.
Gasoline is highly flammable and must be handled with care.
Never fill the tank when the engine is still hot from recent
operation. Do NOT allow open flame, smoking or matches in
the area. Avoid over-filling and wipe up any spills.
To add fuel:
1. Stop the engine and allow it to cool for at least 3 minutes.
2. Remove the fuel cap.
3. Fill the tank to the bottom of the filler neck. This will allow
for fuel expansion.
NOTE: Do not overfill. Refer to your engine manual for
specific fuel recommendations.
4. Install and hand tighten the fuel cap.
Check Engine Oil Level
Interval: Before Each Use
3. To disengage the transmissions (free-wheel position), pull
both transmission release levers back and out (C) so they
lock in the disengaged (free-wheel) position.
4. Disengage the parking brake. The unit can now be pushed
by hand.
5. After moving the unit, re-engage the transmissions (drive
position) by pulling the transmission release levers rearward
and inward (B) to release them from the disengaged position
and then allow them to move to the engaged (drive) position.
Checking Tire Pressures
Tire pressure should be checked periodically, and maintained
at the levels shown in the Specifications chart. Note that these
pressures may differ slightly from the "Max Inflation" stamped
on the side-wall of the tires. The pressures shown provide proper
traction and extend tire life.
Refer to the engine owners manual for dipstick and oil fill
locations and specific engine oil check and fill procedures.
Cleaning Debris from the Machine
Service Interval: Before each use or daily
1. Park the unit on a flat level surface such as a concrete floor.
Disengage the PTO, engage the parking brake, turn the
ignition switch to OFF and remove the key.
2. Clean off any oil, debris, or grass build-up on the machine
and cutting deck, especially under deck belt shields, around
the fuel tank, and around the engine and exhaust area.
Lubrication
This series of mower is equipped with eighteen (18) different
grease fittings. These grease fitting locations must be lubricated
at the intervals as specified in the
Grease Fitting Location
Casters) (A, Figure 16)
Maintenance Chart
Qty of Fittings
(36" Models)
(N/A)Front Casters (See Lubricating the Front Casters)
.
1Forward Speed Control Lever Rod (A, Figure 13)
2Drive Lever Pivots (B)
8Grease-able Ball Joints (C)
1Forward Speed Indicator Pivot (A, Figure 14)
1Transaxle Drive Idler Arm (B)
2Mower Deck Spindles (A, Figures 15)
1Mower Deck Idler Arm (B)
2Front Caster Wheel Axles (See Lubricating the Front
18 ferrisindustries.com
Page 19
Not for
Reproduction
Not all greases are compatible. Red grease (p/n 5022285) is
recommended, automotive-type, high-temperature, lithium
grease may be used when this is not available.
Oil Application Locations
Operator Presence Flap Pivots (D, Figure 13)
Neutral Return Pedal Pivots (E)
Control Rod Pivots (F)
Parking Brake Handle Pivot (C, Figure 14)
Parking Brake Rod Pivots Points (D)
Lower Parking Brake Shaft Pivots (E)
Discharge Chute Rod Hinge (C, Figures 15)
Generally, all moving metal parts should be oiled where contact
is made with other parts. Keep oil and grease off belt and
pulleys. Remember to wipe fittings and surfaces clean both
before and after lubrication.
13
14
15
Lubricating the Front Casters
Interval: Annually
1. Remove the 1/4-28 bolt (B, Figure 16) screwed into the front
caster and install a 1/4-28 grease fitting.
19
Page 20
Not for
Reproduction
16
2. Grease the front caster.
3. Remove the 1/4-28 grease fitting and re-install the 1/4-28
bolt.
4. Repeat process for the other side of the machine.
vapor could travel to any ignition source. Fuel vapor is also toxic
if inhaled, so never store the unit in any structure used for human
or animal habitation.
WARNING
Never store the unit, with gasoline in engine or fuel tank, in a
heated shelter or in enclosed, poorly ventilated enclosures.
Gasoline fumes may reach an open flame, spark or pilot light
(such as a furnace, water heater, clothes dryer, etc.) and
cause an explosion.
Handle gasoline carefully. It is highly flammable and careless
use could result in serious fire damage to your person or
property.
Drain fuel into an approved container outdoors away from
open flame or sparks.
Here is a checklist of things to do when storing your unit
temporarily or in between uses:
Check / Fill Transmission Oil
Oil Type: 20W-50 conventional detergent motor oil.
1. Check the oil level when the unit is cold. Locate the
transmission oil reservoirs (A, Figure 17) positioned by the
fuel tank assembly. The oil should be up to the “FULL
COLD” mark (B). If the oil is below this level, proceed to
step 2.
17
2. Before removing the reservoir caps, make sure the area
around the reservoir cap and fill neck of the reservoir is free
of dust, dirt, or other debris. Remove the reservoir cap.
3. Add oil up to the “FULL COLD” mark (B).
4. Reinstall the reservoir caps.
Storage
Temporary Storage (30 Days or Less)
Remember, the fuel tank will still contain some gasoline, so
never store the unit indoors or in any other area where fuel
• Keep the unit in an area away from where children may
come into contact with it. If there’s any chance of
unauthorized use, remove the spark plug (s) and put in a
safe place. Be sure the spark plug opening is protected
from foreign objects with a suitable cover.
• If the unit can’t be stored on a reasonable level surface,
chock the wheels.
• Clean all grass and dirt from the mower.
Long Term Storage (Longer Than 30 Days)
Before you store your unit for the off-season, read the
Maintenance and Storage instructions in the Safety Rules
section, then perform the following steps:
1. Drain crankcase oil while engine is hot and refill with a grade
of oil that will be required when unit is used again.
2. Prepare the mower deck for storage as follows:
a.) Remove mower deck from the unit.
b.) Clean underside of mower deck.
c.) Coat all bare metal surfaces with paint or light coat of
oil to prevent rusting.
3. Clean external surfaces and engine.
4. Prepare engine for storage. See engine owner’s manual.
5. Clean any dirt or grass from cylinder head cooling fins,
engine housing and air cleaner element.
6. Cover air cleaner and exhaust outlet tightly with plastic or
other waterproof material to keep out moisture, dirt and
insects.
7. Completely grease and oil unit as outlined in the
section.
8. Clean up unit and apply paint or rust preventative to any
areas where paint is chipped or damaged.
9. Be sure the battery is filled to the proper level with water
and is fully charged. Battery life will be increased if it is
removed, put in a cool, dry place and fully charged about
Lubrication
20 ferrisindustries.com
Page 21
Not for
Reproduction
once a month. If battery is left in unit, disconnect the
negative cable.
10. Drain fuel system completely or add a gasoline stabilizer
to the fuel system. If you have chosen to use a fuel stabilizer
and have not drained the fuel system, follow all safety
instructions and storage precautions in this manual to
prevent the possibility of fire from the ignition of gasoline
fumes. Remember, gasoline fumes can travel to distant
sources of ignition and ignite, causing risk of explosion and
fire.
NOTE: Gasoline, if permitted to stand unused for extended
periods (30 days or more), may develop gummy deposits
which can adversely affect the engine carburetor and cause
engine malfunction. To avoid this condition, add a gasoline
stabilizer to the fuel tank and run the engine a few minutes,
or drain all fuel from the unit before placing it in storage.
Starting After Long Term Storage
Before starting the unit after it has been stored for a long period
of time, perform the following steps.
1. Remove any blocks from under the unit.
2. Install the battery if it was removed.
3. Unplug the exhaust outlet and air cleaner.
4. Fill the fuel tank with fresh gasoline. See engine manual for
recommendations.
5. See engine owner’s manual and follow all instructions for
preparing engine after storage.
6. Check crankcase oil level and add proper oil if necessary.
If any condensation has developed during storage, drain
crankcase oil and refill.
7. Inflate tires to proper pressure. Check fluid levels.
8. Start the engine and let it run slowly. DO NOT run at high
speed immediately after starting. Be sure to run engine only
outdoors or in well ventilated area.
Maintenance Schedule
ENGINE MAINTENANCE
Before each use
Check engine oil level.
Clean visible debris from engine compartment.
Every 50 Hours
Inspect / Clean spark arrester.**
Every 100 Hours
Check fuel filter.
Refer to engine owner's manual
Service air filter.
Change engine oil and filter.
Check / Replace spark plugs.
* More often in hot (over 85° F; 30° C) weather or dusty operating
conditions.
**If equipped. Replace if damaged.
Specifications
NOTE: Specifications are correct at time of printing and are
subject to change without notice.
ENGINE
Fits models: 5901441
18.5 Gross HP† Kawasaki
KawasakiMake
FS600V-DS00-SModel
36.8 Cu. in (603 cc)Displacement
Electrical System
†Power Ratings: All power levels are stated gross horsepower
per SAE J2723 as rated by Kawasaki and tested per the SAE
J1995 test standard. The gross power curves and more
information can be viewed at www.kawasaki-criticalpower.com.
12 volt, 15 amp charging coil; Battery:
340 cca
1.8 US qt. (1.7 L) w/ filterOil Capacity
The following schedule should be followed for normal care of
your unit. You will need to keep a record of your operating time.
UNIT MAINTENANCE
Before each use
Check safety interlock system.
Check unit brakes.
Check unit for loose hardware.
Check hydraulic oil level.
Check tire pressures.
Every 25 Hours
Clean mower deck and check / Replace mower blades.*
Lubricate unit and mower deck.*
Every 100 Hours
Check mower blade stopping time.
Every 200 Hours
Change hydraulic oil filter.*
CHASSIS
5 gallons (18.73 L)Fuel Tank Capacity
Rear Wheels
20.00 X 7.00 - 10Tire Size
15 psi (1.03 bar)Inflation Pressure
Front Wheels
9.00 X 3.50 - 4Tire Size
N/A (Flat Free)Inflation Pressure
TRANSMISSIONS
ZJ-GMFE-3L5B-1PLX (5104471)LH
ZJ-KMFE-3L5C-1PLX (5104472)RH
ZT3100Type
SAE 20W-50 motor oilHydraulic Fluid
Speeds
21
Page 22
Not for
Reproduction
0-6 MPH (0-9.7 km/h)Forward
0-3 MPH (0-4.83 km/h)Reverse
DIMENSIONS
Models with 36" Rear Discharge Mower Deck
78-1/2" (199.4 cm)Overall Length
36-3/4" (93.3 cm)Overall Width
42-9/16" (108 cm)Overall Height
632 lbs (287 kg)Weight (approx.)
Warranty
Warranty Statement
BRIGGS & STRATTON WARRANTY POLICY (September 2012)
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period
specified below, it will repair or replace, free of charge, any part
that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or
replacement under this warranty must be borne by purchaser.
This warranty is effective for and is subject to the time periods
and conditions stated below. For warranty service, find the
nearest Authorized Service Dealer in our dealer locator map at
ferrisindustries.com
Service Dealer, and then make the product available to the
Authorized Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties,
including those of merchantability and fitness for a
particular purpose, are limited to one year from purchase,
or to the extent permitted by law . All other implied
warranties are excluded. Liability for incidental or
consequential damages are excluded to the extent
exclusion is permitted by law. Some states or countries do
not allow limitations on how long an implied warranty lasts, and
some states or countries do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
and exclusion may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which
vary from state to state or country to country.**
Covered Parts
Riding mowers
Walk mowers (over 30
inches of cutting width)
Pads, Hoses, Battery,
Blades
.The purchaser must contact the Authorized
WARRANTY PERIOD
Rental Warranty PeriodStandard Warranty
Period
90 days4 years (48 months) or
500 hours, which occurs
first.
Unlimited hours during
the first 2 years (24
months)
(+Except as noted below)
90 days2 years (24 months)
unlimited hours
(+Except as noted below)
90 days90 days+Belts, Tires, Brake
90 days1 year+Attachments
+Engine*
* Emissions-related components are covered by the Emissions
Warranty Statement
** In Australia - Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. For warranty service,
find the nearest Authorized Service Dealer in our dealer locator
map at FERRISINDUSTRIES.COM/AU, or by calling 1300 274
447, or by emailing or writing to
salesenquires@briggsandstratton.com.au, Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first
retail end user, and continues for the period of time or hours
stated in the table above.
No warranty registration is necessary to obtain warranty
on Briggs & Stratton products. Save your proof of purchase
receipt. If you do not provide proof of the initial purchase
date at the time warranty service is requested, the
manufacturing date of the product will be used to determine
the warranty period.
We welcome warranty repair and apologize to you for being
inconvenienced. Warranty service is available only through
Ferris
Authorized Service Dealers. Most warranty repairs are
handled routinely, but sometimes requests for warranty service
may not be appropriate. This warranty only covers defects in
materials or workmanship. It does not cover damage caused
by improper use or abuse, improper maintenance or repair,
normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this
product is described in the Operator's Manual. Using the product
in a way not described in the Operator's Manual or using the
product after it has been damaged will void your warranty.
Warranty is not allowed if the serial number on the product has
been removed or the product has been altered or modified in
any way, or if the product has evidence of abuse such as impact
damage, or water/chemical corrosion damage.
Improper Maintenance or Repair - This product must be
maintained according to the procedures and schedules provided
in the Operator's Manual, and serviced or repaired using genuine
Briggs & Stratton parts or equivalent. Damage caused by lack
of maintenance or use of non-original parts is not covered by
warranty.
Normal Wear - Like all mechanical devices, your unit is subject
to wear even when properly maintained. This warranty does
not cover repairs when normal use has exhausted the life of a
part or the equipment. Except as noted in the warranty period,
maintenance and wear items such as filters, belts, cutting
blades, and brake pads (except engine brake pads) are not
See Engine Operator's
Manual
ABOUT YOUR WARRANTY
See Engine Operator's
Manual
22 ferrisindustries.com
Page 23
Not for
Reproduction
covered by warranty due to wear characteristics alone, unless
the cause is due to defects in material or workmanship.
Stale Fuel - In order to function correctly, this product requires
fresh fuel that conforms to the criteria specified in the Operator's
Manual. Damage caused by stale fuel (carburetor leaks, clogged
fuel tubes, sticking valves, etc) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to
accident, abuse, modifications, alterations, improper servicing,
freezing or chemical deterioration. Attachments or accessories
that were not originally packaged with the product are also
excluded. There is no warranty coverage on equipment used
for primary power in place of utility power or on equipment used
in life support applications. This warranty also excludes failures
due to acts of God and other force majeure events beyond the
manufacturer's control.
23
Page 24
Not for
Reproduction
Loading...