Ferris F800X Series, 5900911, 5900940, F800XY30DCE, F800XY30D ANSI-EXPORT Operator's Manual

...

Download

Page 1

OPERATOR’S

Not for

Reproduction

MANUAL

F800X Series

Zero-Turn Riding Mower

Tractor

Model Number: Description

5900911 F800XY30DCE

5900940 F800XY30D ANSI-EXPORT

Mower Deck

5900912 F800X/61CE, 61” Mower Deck

5900941 F800X/61 ANSI-EXPORT

5102607

Rev D

Page 2

Thank you for purchasing this quality-built Ferris product.

Not for

Reproduction

We’re pleased that you’ve placed your confidence in the Ferris brand. When operated and maintained according to the instructions in this manual, your Ferris product will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with this machine and how to avoid them. This machine is designed and intended to be used and maintained according to the manual and operated by trained professionals for finish cutting of established lawns and is not intended for any other purpose. It is important that you read and understand these instructions thoroughly before attempting to start or operate this equipment.

Save these original instructions for future reference.

The images in this document are representative, and are meant to compliment the instructional copy they accompany. Your unit may vary from the images displayed. LEFT and RIGHT are as seen from the operator’s position.

The Illustrated Parts List for this machine can be downloaded from ferrisindustries.com. Please provide model and serial number when ordering replacement parts.

Product Identification Tags

PRODUCT REFERENCE DATA

Unit Model Number Unit SERIAL Number

Mower Deck Model Number Mower Deck SERIAL Number

Dealer Name Date Purchased

ENGINE REFERENCE DATA

Engine Make Engine Model

Engine Type/Spec Engine Code/Serial Number

Ferris is a trademark of Briggs & Stratton Corporation, LLC. Milwaukee, WI, USA.

Contact Information:

Briggs & Stratton Power Products Group, LLC.

5375 N. Main St. Munnsville, NY 13409-4003 (800) 933-6175 www.ferrisindustries.com

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Battery posts, terminals, and related accessories contain lead and lead compounds – chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

WARNING

Page 3

Table of Contents

Not for

Reproduction

Operator Safety .................................................. 2

Safety Decals ........................................................11

Safety Icons ..........................................................13

Safety Interlock System.........................................14

Features & Controls ......................................... 15

Identification Numbers ..........................................15

Control Functions ..................................................16

Operation .......................................................... 18

General .................................................................18

Checks Before Starting .........................................19

Seat Adjustment ....................................................19

Check Tire Pressures ............................................20

Mowing Height Adjustment ...................................20

Priming the Fuel System .......................................21

Check Engine Coolant ..........................................22

Change Engine Coolant ........................................22

Clean Radiator & Screens .....................................22

Starting The Engine...............................................23

Stopping The Mower .............................................23

Safety Interlock & Mower Deck

Positioning Instructions .......................................23

Zero-Turn Driving Practice ....................................24

Mowing ..................................................................26

Mowing Recommendations ...................................26

Mowing Methods ...................................................27

Pushing the Rider by Hand ...................................28

Raise and Lower the Roll Bar ................................29

Attachment Removal and Installation

Procedure ............................................................30

Maintenance ..................................................... 32

Maintenance Schedule .........................................32

Ground Speed Control Lever Adjustment .............33

Speed Balancing Adjustment ................................33

Storage..................................................................34

Starting After Long Term Storage .........................34

Specifications ................................................... 35

Slope Identification Guide ............................... 36

NOTE: In this manual, “left” and “right” are referred to as seen from the operating position.

Page 4

Operator Safety

Not for

Reproduction

Read the Manual

Operating Safety

Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety.

Do not operate this machine unless you have been trained. Reading and understanding this operator’s manual is a way to train yourself.

Power equipment is only as safe as the operator. If it is misused, or not properly maintained, it can be dangerous! Remember, you are responsible for your safety and that of those around you.

Use common sense, and think through what you are doing. If you are not sure that the task you are about to perform can be safely done with the equipment you have chosen, ask a professional: contact your local authorized dealer.

The operator’s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the product’s features and controls, and maintenance information is included to help you get the most out of your equipment investment.

Be sure to completely read the Safety Rules and Information found on the following pages. Also completely read the Operation section.

Children

Tragic accidents can occur with children. Do not allow them anywhere near the area of operation. Children are often attracted to the unit and mowing activity. Never assume that children will remain where you last saw them. If there is a risk that children may enter the area where you are mowing, have another responsible adult watch them.

Page 5

Operator Safety

Not for

Reproduction

Slope Operation

Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover. You should not operate on a slope greater than a 5.4 foot rise over a 20 foot length (15 degrees).

Always mow across slopes, not up and down (to maintain traction on the wheels) and avoid sudden turns or rapid speed changes. Reduce speed and use extreme caution on ALL slopes.

Also, note that the surface condition you are on can greatly impact your ability to safely operate this machine. Operating on wet or slippery slopes can cause sliding and loss of steering and control. Do not operate on slopes that are slippery, wet, or have soft soil conditions.

If you feel unsure about operating the unit on a slope, don’t do it. It’s not worth the risk.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and throw debris that could seriously injure a bystander. Be sure to clean up the area to be mowed and remove objects that could be thrown by the blade BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If someone does enter the area, shut the unit off immediately until they leave.

This equipment has many moving parts that can injure you or someone else. However, if you stay in the operator zone (stay seated in the seat), and follow the safety rules in this operator’s manual, the unit is safe to operate.

The mower deck has spinning mower blades that can amputate hands and feet. Do not allow anyone near the unit while it is running! Keep safety devices (guards, shields, and switches) in place and working.

To help you, the operator, use this equipment safely, it is equipped with an operator-present safety system. Do NOT attempt to alter or bypass the system. See your dealer immediately if the system does not pass all the safety interlock system tests found in this manual.

Moving Parts

Page 6

Operator Safety

Not for

Reproduction

Roll Bar Use

Keep the roll bar in the raised position and fasten the seat belt. There is no roll over protection when the roll bar is down! Do not jump off if the mower tips (it is safer to be secured by the seat belt with the roll bar raised.)

Lower the roll bar only when necessary (such as to temporarily clear a low overhanging obstacle) and NEVER remove it. Do NOT use the seat belt when the roll bar is down. Raise the roll bar as soon as clearance permits.

Retaining Walls, Drop-

offs, and Water

Retaining walls and drop-offs around steps and water are a common hazard. Give yourself a minimum of two mower widths of clearance around these hazards and hand-trim with a walk behind mower or string trimmer. Wheels dropping over retaining walls, edges, ditches, embankments, or into water can cause rollovers, which may result in serious injury, death, or drowning.

Overhead Obstacles

Check for overhead clearances before driving under any objects. Do not allow the roll bar to contact low overhanging obstacles such as tree

branches and guide wires.

Page 7

Operator Safety

Not for

Reproduction

Fuel and Maintenance

Always disengage all drives, shutoff the engine, and remove the key before doing any cleaning, refueling, or servicing.

Gasoline and its vapors are extremely flammable. Do not smoke while operating or refueling. Do not add fuel while engine is hot or running. Allow engine to cool for at least 3 minutes prior to adding fuel.

Do not add fuel indoors, in an enclosed trailer, garage, or any other enclosed area that is not well ventilated. Gasoline spills should be cleaned up promptly and before operation begins.

Gasoline should be stored only in sealed containers approved for fuel.

Proper maintenance is critical to the safety and performance of your unit. Keep the unit free of grass, leaves, and excess oil. Be sure to perform the maintenance procedures listed in this manual, especially periodically testing the safety system.

Enclosed Areas

Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers. The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death.

Page 8

Operator Safety

Not for

Reproduction

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle in text signifies important cautions or warnings which must be followed.

TRAINING

1. Read, understand, and follow all instructions in the manual and on the unit before starting. If the operator(s) or mechanic(s) can not read English it is the owner’s responsibility to explain this material to them.

2. Become familiar with the safe operation of the equipment, operator controls, and safety signs.

3. All operators and mechanics should be trained. The owner is responsible for training the users.

4. Only allow responsible adults, who are familiar with the instructions, to operate the unit.

5. Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the operator.

6. The owner/user can prevent and is responsible for accidents or injuries occurring to themselves, other people or property.

7. Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.

PREPARATION

1. Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Use only accessories and attachments approved by the manufacturer.

2. Wear appropriate clothing including safety shoes, safety glasses and ear protection. Long hair, loose clothing or jewelry may get tangled in moving parts.

3. Inspect the area where the equipment is to be used and remove all objects such as rocks, toys and wire, which can be thrown by the machine.

4. Use extra care when handling gasoline and other fuels. They are flammable and vapors are explosive.

a) Use only an approved container.

b) Never remove fuel cap or add fuel with the

engine running. Allow engine to cool before refueling. Do not smoke.

c) Never refuel or drain the machine indoors.

5. Check that operator’s presence controls, safety switches and shields are attached and functioning properly. Do not operate unless they are functioning properly.

OPERATION

1. Never run an engine in an enclosed area.

2. Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards.

3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided.

4. Be sure of your footing while using pedestrian controlled equipment, especially when backing up. Walk, don’t run. Reduced footing could cause slipping.

5. Slow down and use extra care on hillsides. Be sure to travel in the recommended direction on hillsides. Turf conditions can affect the machines stability. Use caution when operating near dropoffs.

6. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while traveling in reverse.

7. Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the deflector in place.

8. Slow down and use caution when making turns and when changing directions on slopes.

9. Never raise deck with the blades running.

10. Never leave a running unit unattended. Always disengage the PTO, set parking brake, stop engine, and remove keys before dismounting. Keep hands and feet away from the cutting units.

11. Turn off the PTO switch to disengage the blades when not mowing.

12. Never operate with guards not securely in place. Be sure all interlocks are attached, adjusted properly and functioning properly.

13. Never operate with the discharge deflector raised, removed or altered, unless using a grass catcher.

14. Do not change the engine governor setting or overspeed the engine.

15. Stop on level ground, lower implements, disengage drives, engage parking brake, shut off engine before leaving the operator’s position for any reason including emptying the grass catchers or unclogging the chute.

16. Stop equipment and inspect blades after striking objects or abnormal vibration occurs. Make necessary repairs before resuming operations.

17. Keep hands and feet away from the cutting units.

18. Look behind and down before backing up to be sure of a clear path.

19. Never carry passengers and keep pets and bystanders away.

20. Do not operate the unit while under the influence of alcohol or drugs.

21. Slow down and use caution when making turns and crossing roads and sidewalks. Stop blades if not mowing.

22. Use care when loading or unloading the machine into a trailer or truck.

Page 9

Operator Safety

Not for

Reproduction

23. Use care when approaching blind corners, shrubs, trees or other objects that may obscure vision.

24. To reduce fire hazard, keep unit free of grass, leaves & excess oil. Do not stop or park over dry leaves, grass or combustible materials.

WARNING

It is a violation of California Public Resource Code, Section 4442, to use or operate the engine on any forest-covered, brush-covered or grass-covered land unless the exhaust system is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order. Other states or federal jurisdictions may have similar laws. Contact an Authorized Service Dealer to obtain a spark arrester designed for the exhaust system installed on this engine.

25. OSHA regulations may require the use of hearing protection when exposed to sound levels greater than 85 dBA for an 8 hour time period.

CAUTION

This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause hearing loss though extended periods of exposure.

Wear hearing protection when operating this machine.

5. Use extra care with grass catchers or other

6. Keep all movement on the slopes slow and

7. See your authorized dealer for recommendations

Do Not

1. Avoid starting, stopping, or turning on a slope.

2. Do not turn on slopes unless necessary, and then,

3. Do not mow near drop-offs, ditches, or

4. Do not mow on wet grass. Reduced footing or

5. Do not try to stabilize the unit by putting your foot

6. Do not mow excessively steep slopes.

7. Do not use grass catcher on steep slopes.

8. Do not mow slopes if you cannot back up them.

TOWED EQUIPMENT (RIDE-ON UNITS)

1. Tow only with a machine that has a hitch designed

2. Follow the manufacturer’s recommendations

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not drive on it.

WARNING

Do not use this machine on slopes greater than 15°.*

Select slow ground speed before driving onto slope. Use extra caution when operating on slopes with rear-mounted grass catchers.

Mow across the face of slopes, not up and down, use caution when changing directions and DO NOT START OR STOP ON SLOPE.

1. Mow across slopes, not up and down.

2. Remove obstacles such as rocks, tree limbs, etc.

3. Watch for holes, ruts, or bumps. Uneven terrain could overturn the unit. Tall grass can hide obstacles.

4. Use slow speed. Choose a slow speed so that

*This limit was determined per CEN Standard EN 836:1997, Section

5.2.2 and is based on the EN 836 Stability Test procedure described in

Section 4.2.4.2. The 15 degree “limit of stability” is equal to 50% of the angle at which machine lift-off occurred in static tests. Actual dynamic stability may vary depending on operating conditions.

you will not have to stop or change speed while on the slope.

3. Never allow children or others in or on towed

4. On slopes, the weight of the towed equipment

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and the mowing activity. Never assume that children will remain where you last saw them.

1. Keep children out of the mowing area and under

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind

4. Never carry children, even with the blade(s) off.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners,

attachments. These can change the stability of the unit.

gradual. Do not make sudden changes in speed or direction.

of available weights to improve stability.

If tires lose traction (i.e. machine stops forward motion on a slope), disengage the blade(s) (PTO) and drive slow off the slope.

turn slowly and gradually uphill, if possible. Never mow down slopes.

embankments. The operator could lose footing or balance or mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.

traction could cause sliding.

on the ground. (ride-on units)

for towing. Do not attach towed equipment except at the hitch point.

for weight limit for towed equipment and towing on slopes. See attaching a trailer under OPERATION.

equipment.

may cause loss of traction and loss of control.

the watchful care of another responsible adult.

and down for small children.

They may fall off and be seriously injured or interfere with safe unit operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.

shrubs, trees, or other objects that may obscure vision.

Page 10

Operator Safety

Not for

Reproduction

EMISSIONS

1. Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period and Air Index information on the engine emissions label.

IGNITION SYSTEM (GASOLINE MODELS)

1. This spark ignition system complies with Canadian ICES-002.

SERVICE AND MAINTENANCE

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where there is an open flame, spark, or pilot light such as near a water heater or other appliance.

6. Never fill containers inside a vehicle or on a truck bed with a plastic bed liner. Always place containers on the ground away from your vehicle before filling.

7. Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing immediately.

10. Never over-fill the fuel tank. Replace gas cap and tighten securely.

11. Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

12. If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated.

13. Replace all fuel tank caps and fuel container caps securely.

Maintenance and Storage

1. Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage.

2. Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods.

3. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.

4. Never store the machine or fuel container inside

where there is an open flame, such as in a water heater. Allow unit to cool before storing.

5. Shut off fuel while storing or transporting. Do not store fuel near flames or drain indoors.

6. Keep all hardware, especially blade attachment bolts, tight and keep all parts in good working condition. Replace all worn or damaged decals.

7. Never tamper with safety devices. Check their proper operation regularly.

8. Disengage drives, lower implement, set parking brake, stop engine and remove key or disconnect spark plug wire. Wait for all movement to stop before adjusting, cleaning or repairing.

9. Clean grass and debris from cutting units, drives, mufflers, and engine to prevent fires. Clean up oil or fuel spillage.

10. Let engine cool before storing and do not store near flame.

11. Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

12. Park machine on level ground. Never allow untrained personnel to service machine.

13. Use jack stands to support components when required.

14. Carefully release pressure from components with stored energy.

15. Disconnect battery or remove spark plug wire before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last.

16. Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace blades. Never straighten or weld them.

17. Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running.

18. Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothes and use insulated tools.

19. Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary.

20. Check brake operation frequently. Adjust and service as required.

21. Use only factory authorized replacement parts when making repairs.

22. Always comply with factory specifications on all settings and adjustments.

23. Only authorized service locations should be utilized for major service and repair requirements.

24. Never attempt to make major repairs on this unit unless you have been properly trained. Improper service procedures can result in hazardous operation, equipment damage and voiding of manufacturer’s warranty.

25. Units with hydraulic pumps, hoses, or motors: WARNING: Hydraulic fluid escaping under pressure may have sufficient force to penetrate skin and cause serious injury. If foreign fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result. Keep body and hands away from pin holes or nozzles that eject hydraulic fluid under high pressure. Use paper or cardboard, and not hands, to search for

Page 11

Operator Safety

Not for

Reproduction

leaks. Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system. If leaks occur, have the unit serviced immediately by your authorized dealer.

26. WARNING: Stored energy device. Improper release of springs can result in serious personal injury. Springs should be removed by an authorized technician.

27. Models equipped with an engine radiator: WARNING: Stored energy device. To prevent serious bodily injury from hot coolant or steam blow-out, never attempt to remove the radiator cap while the engine is running. Stop the engine and wait until it is cool. Even then, use extreme care when removing the cap.

ROLL BAR INSTRUCTIONS

For models equipped with factory-installed Roll Over Protection System (ROPS).

WARNING

In order to avoid serious injury or death from roll over, it is important to follow the warnings listed below.

OPERATIONAL WARNINGS

• Always use the seat belt when the roll bar is in the raised position.

• Never use the seat belt when the roll bar is in the down position.

• Remember there is no roll over protection when the roll bar is in the down position so it is very important to always keep the roll bar in the raised position whenever possible.

• Lower the roll bar to the down position only when it is absolutely necessary.

• Check for overhead clearances before driving under any objects. Do not allow roll bar to contact low overhanging obstacles such as tree branches and guide wires.

• Never remove the roll bar from the vehicle.

• Do not exceed the machine weight rating of the roll bar.

• Read and follow all of the instructions shown below regarding the inspection and maintenance of the roll bar structure and the seat belt.

INSPECTION OF THE ROLL BAR PROTECTIVE STRUCTURE

To maintain operator roll over protection and roll bar effectiveness:

• If a ROLL BAR becomes damaged for any reason, such as a collision, roll over or impact, the ROLL BAR must be replaced. Small undetectable cracks can reduce the effectiveness of the ROLL BAR. Never weld, straighten, or repair the ROLL BAR.

• Never alter the ROLL BAR by welding anything to it or by drilling additional holes.

• BEFORE FIRST TIME USE - Inspect the ROLL BAR structure and mounting hardware for:

1) Check to make sure the machine GVW (Gross Vehicle Weight), including attachments, restrained payload, fuel and operator, is not in excess of the maximum weight specified on the ROLL BAR label.

2) Make sure there isn’t any missing, damaged, or loose mounting hardware.

3) Make sure the ROLL BAR has been correctly and completely installed.

• EVERY 100 HOURS - Inspect the ROLL BAR structure and mounting hardware for:

1) Any cracks in the structure (structural members and/or welds).

2) Significant corrosion on any part of the ROLL BAR structure or hardware.

3) Missing, damaged, or loose mounting hardware

4) Mounting hardware that is of a grade lesser than specified.

5) Machine GVW (Gross Vehicle Weight), including attachments, restrained payload, fuel and operator, in excess of the maximum weight specified on the ROLL BAR label.

6) Any modifications that have been made, such as unauthorized welds and holes.

7) Any permanent deformation or twisting of the ROLL BAR structure.

8) That the ROLL BAR label is still in place and is readable.

WARNING

Failure to properly inspect and maintain the ROLL BAR protective structure can cause serious injury or death.

A ROLL BAR, like any other safety device, needs to be periodically inspected to verify that the integrity of the device has not been compromised through normal machine use, misuse, age degradation, modifications, or a roll over.

• If there is any doubt as to the condition of the

9) That the ROLL BAR on-product warning labels are still on the ROLL BAR and are readable.

ROLL BAR, remove the machine from service and contact your dealer for assistance.

Page 12

Operator Safety

Not for

Reproduction

WARNING

Failure to properly inspect and maintain the seat belt can cause serious injury or death.

INSPECTION AND MAINTENANCE OF THE ROLL BAR SEAT BELT

• The seat belt like the ROLL BAR, needs to be periodically inspected to verify that the integrity has not been compromised through normal machine use, misuse, age degradation, modifications, or a roll over. If the seat belt does not pass all of the following tests, it should be replaced.

• BEFORE EACH USE – Conduct the following inspections/maintenance of the seat belt and retraction mechanism:

1) Check for dirt or debris in the retraction mechanism. If dirt or debris is found, it should be removed.

2) Check to make sure the retraction mechanism retracts easily and completely.

3) Check for damage to any part of the seat belt such as nicks, cuts, loose stitching, or fraying.

INSPECT BUCKLE & LATCH

INSPECT WEBBING

4) Check that the buckle and latch operate properly and that the latch plate is not excessively worn, deformed, or the buckle is damaged or cracked. The seat belt should latch and release easily.

Page 13

Safety Decals

Not for

Reproduction

This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.

Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effectively, we have placed several safety labels on the unit to remind you of this important information while you are operating your unit.

All DANGER, WARNING, CAUTION and instructional messages on your rider and mower should be carefully read and obeyed. Personal bodily injury can result when these instructions are not followed. The information is for your safety and it is important! The safety decals below are on your rider and mower.

If any of these decals are lost or damaged, replace them at once. See your local dealer for replacements.

These labels are easily applied and will act as a constant visual reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, effective operation.

Operator Safety

This decal is installed on the battery for CE models only.

G , H

Page 14

Operator Safety

Not for

Reproduction

1. WARNING: Read and understand the Operator’s Manual before using this machine. Know the location and function of all controls. Do not operate this machine unless you are trained.

2. WARNING: Consult technical literature before performing technical repairs or maintenance. When leaving the machine, shutoff engine, set the parking brake to the lock position and remove the ignition key.

3. DANGER - AMPUTATION AND DISMEMBERMENT HAZARD: To avoid injury from rotating blades and moving parts, keep safety devices (guards, shields and switches) in place and working.

4. DANGER - LOSS OF TRACTION, SLIDING,

STEERING AND CONTROL ON SLOPES HAZARD: If machine stops forward motion or starts

sliding on a slope, stop the blades and drive slowly off the slope.

5. DANGER - AMPUTATION HAZARD: Do not mow when children or others are around. Never carry riders especially, children even with the blades off. Do not mow in reverse unless absolutely necessary. Look down and behind – before and while backing.

6. DANGER - TIPPING AND SLIPPING HAZARD: Mow across slopes, not up and down. Do not operate on slopes over 15 degrees. Avoid sudden and sharp (fast) turns while on slopes. This limit was determined per CEN Standard EN 836:1997, Section 5.2.2 and is based on the EN 836 Stability Test procedure described in Section 4.2.4.2. The 15 degree “limit of stability” is equal to 50% of the angle at which machine lift-off occurred in static tests. Actual dynamic stability may vary depending on operating conditions.

7. DANGER - THROWN OBJECTS HAZARD: Keep bystanders and children a safe distance away. Remove objects that can be thrown by the blade. Do not mow without discharge chute in place.

8. DANGER - THROWN OBJECTS HAZARD: Do not mow without discharge chute or entire grass catcher in place

9. DANGER - AMPUTATION AND THROWN OBJECTS HAZARD: To avoid injury from rotating blades, stay clear of deck edge and keep others away.

10. DANGER: FIRE HAZARD: Keep unit free of grass, leaves and excess oil. Do not add fuel while engine is hot or running. Stop engine, remove key and allow to cool for at least 3 minutes prior to adding fuel. Do not add fuel indoors, in an enclosed trailer, garage or other enclosed areas. Clean up spilled fuel. Do not smoke while operating this machine.

www.ferrisindustries.com

Page 15

Operator Safety

Not for

Reproduction

Danger: Machine Rollover.

Do not operate on any slopes when wet or slippery. Do not operate near drop-offs or near water.

Warning: Hot Surface

Avoid contact with engine and hot surfaces. Wait for unit to cool before touching.

Danger: Dismemberment.

This machine can crush and cut. Keep hands away from deck lift rod.

Warning: Avoid Serious Injury or Death from Roll Over

Keep roll bar in the raised position and use seat belt. Do NOT use seat belt when the roll bar is down.

Warning: Avoid Serious Injury or Death from Roll Over

Keep roll bar in the raised position and use seat belt. There is no roll over protection when roll bar is down. Lower roll bar only when necessary and NEVER remove it. Raise the roll bar as soon as clearance permits.

Warning: Low Overhanging Obstacles Hazard

Check for overhead clearances before driving under any objects. Stay clear. Do NOT allow roll bar to contact low overhanging obstacles, such as tree branches and guide wires. Read and follow all operating instructions and warnings in the operator’s manual.

Warning: Avoid Serious Injury or Death from Roll Over

Do NOT jump off if the mower tips. Read and follow all operating instructions and warnings in the operator’s manual.

Warning: Escaping Steam Can Cause Burns

Never remove the radiator cap or radiator reservoir cap while the engine is hot or running. Severe thermal burns or injury can occur by escaping steam or hot coolant.

Warning : Fire hazard

Keep children, open flames and sparks away from the battery, which could ignite explosive gases.

Warning: Sulfuric acid can cause blindness or severe burns

Always wear safety goggles or a face shield when working on or near a battery.

Warning: Batteries produce explosive gases

Read and understand the Operator’s Manual before using this machine.

Important: Do not discard a battery in the trash

Contact local authorities for disposal and/or recycling of batteries.

Danger: Dismemberment

This machine can crush and cut. Keep hands away from belt and pulleys.

Safety Icons

The alert symbol ( ) is used to identity safety information about hazards that can result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the alert symbol to indicate the likelihood and the potential severity of the injury. In addition, a hazard icon may be used to represent the type of hazard. An explanation of hazard levels and icons are as follows:

DANGER

This indicates a hazard which, if not avoided, will result in serious injury or death.

WARNING

This indicates a hazard which, if not avoided, could result in serious injury or death.

CAUTION

This indicates a hazard which, if not avoided, might result in serious injury or death.

NOTICE

This message presented without the alert symbol indicates a situation where the unit or property could be damaged.

Page 16

Operator Safety

Not for

Reproduction

Safety Interlock System

(CE Models: S/N: 2014683183 & Below)

This unit is equipped with safety interlock switches. These safety systems are present for your safety, do not attempt to bypass safety switches, and never tamper with safety devices. Check their operation regularly.

Operational SAFETY Checks

Test 1 — Engine should NOT crank if:

• PTO switch is engaged, OR

• Parking brake is not engaged, OR

• Ground speed control levers are not in the NEUTRAL position, OR

Test 2 — Engine SHOULD crank if:

• PTO switch is NOT engaged, AND

• Parking brake is engaged, AND

• Ground speed control levers are locked in the NEUTRAL position, AND

Test 3 — Engine should SHUT OFF if:

• Operator rises off the seat under any condition.

• Operator moves the ground speed control levers out of their NEUTRAL positions before disengaging the parking brake.

• Operator moves the ground speed control levers out of the NEUTRAL position be positioning the mower deck in the operating position.

Test 4 — PTO SHOULD shut off if:

• Operator raises the deck from the operating position with the PTO engaged.

Test 5 — PTO should NOT engage if:

• Operator engages the PTO before the mower deck is in the operating position.

Test 6 — Blade Brake Check

Mower blades and mower drive belt should come to a complete stop within seven (7) seconds after electric PTO switch is turned off (or operator raises from the seat). If mower drive belt does not stop within seven (7) seconds, see your dealer.

NOTE: Once the engine has stopped, the PTO switch must be turned off, parking brake must be engaged, the ground speed control levers must be locked in the NEUTRAL position, after the operator returns to the seat to start the engine.

Safety Interlock System

(ANSI-Export Models: All) (CE Models: S/N: 2014683184 & Above)

Operational SAFETY Checks

Test 1 — Engine should NOT crank if:

• PTO switch is engaged, OR

• Parking brake is not engaged, OR

• Ground speed control levers are not in the NEUTRAL position, OR

Test 2 — Engine SHOULD crank if:

• PTO switch is NOT engaged, AND

• Parking brake is engaged, AND

• Ground speed control levers are locked in the NEUTRAL position, AND

Test 3 — Engine should SHUT OFF if:

• Operator rises off the seat with the PTO engaged, OR

• Operator rises off the seat with the parking brake disengaged.

• Operator moves the ground speed control levers out of their NEUTRAL positions before disengaging the parking brake.

• Operator moves the ground speed control levers out of the NEUTRAL position be positioning the mower deck in the operating position.

Test 4 — PTO SHOULD shut off if:

• Operator raises the deck from the operating position with the PTO engaged.

Test 5 — PTO should NOT engage if:

• Operator engages the PTO before the mower deck is in the operating position.

Test 6 — Blade Brake Check

www.ferrisindustries.com

Page 17

WARNING

AMPLE

Not for

Reproduction

If the unit does not pass a safety test, do NOT operate it. See your authorized dealer. Under no circumstance should you attempt to defeat the purpose of the safety interlock system.

Features and Controls

Identification Numbers

AMPLE

PRODUCT IDENTIFICATION

XXXXXXXXXXXXXXX MODEL XXXXXXX

SERIAL

XXXXXXXX

123456 789012

Briggs & Stratton Power Product Group, LLC XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX

When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers.

XXXX

XXX

min

AMPLE

XXX

20xx

Assembled in U.S.A

CE Models

Operator Safety

Tractor

Identiﬁ cation

Tag

Mower Deck

Identiﬁ cation

Tag

Record your model / serial number and engine serial numbers on the space provided on the inside front cover for easy access. These numbers can be found in the locations shown.

NOTE: For location of engine identification numbers, refer to engine owner’s manual.

CE Identification Tag Markings

A. Manufacturer’s Identification Number B. Product Description C. Serial Number D. Manufacturer’s Address E. CE Compliance Logo F. Year of Manufacture G. Maximum Engine Speed in Rotations per Minute H. Power Rating in Kilowatts I. Mass of Unit in Kilograms J. Sound Power in Decibels *

This unit complies with European Harmonized Lawn Mower Standard EN 836, European Machinery Directive 2006/42/EC, and European EMC Directive 2004/108/EC

* Tested according to 2000/14/EC

XXXXXXXXXXXXXXX MODEL XXXXXXX

SERIAL

XXXXXXXX

123456 789012

Briggs & Stratton Power Product Group, LLC XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX

PRODUCT IDENTIFICATION

XXXX

min

XXX

20xx

Assembled in U.S.A

Page 18

Features and Controls

Not for

Reproduction

Features and Controls

A. S/N: 2014648787 & Below B. S/N: 2014648788 & Above

Control Functions

The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.

Cutting Height Adjustment Pin

With the actuator fully extended move the cutting height adjustment pin to the desired cutting height. Retract the actuator until it makes contact with the cutting height adjustment pin to set the cutting height.

Ground Speed Control Levers

These levers control the ground speed of the rider. The left lever controls the left drive wheel and the right lever controls the right drive wheel. Moving a lever forward increases the FORWARD speed of the associated wheel, and pulling back on and lever increases the REVERSE speed.

Note: The further a lever is moved away from the neutral position the faster the drive wheel will turn.

See Zero-Turn Driving Practice section for steering instructions.

Seat Adjustment Lever

The seat can be adjusted forward and back. S/N: 2014648787 & Below: Move the lever away from the seat, position the seat as desired, and release the lever to lock the seat in position. S/N: 2014648788 & Above: Move the lever to the left, position the seat as desired, and release the lever to lock the seat in position.

Operating Position Indicator Lamp

The operating position indicator lamp will flash when the mower deck is not properly positioned in the operating position. When the mower deck is properly positioned the operating position indicator lamp will stop flashing and shut off. See Positioning the Mower Deck for Operation for instructions on properly positioning the mower deck.

www.ferrisindustries.com

Page 19

Features and Controls

Not for

Reproduction

Retractable Seat Belt

The seat belt is used to secure the operator to the seat. The seat belt should ALWAYS be worn when the Roll Bar is in the raised position. The seat belt should NEVER be worn when the Roll Bar is in the down position.

Parking Brake

Pull the parking brake handle up to engage the parking brake. Push the parking brake handle down to disengage the parking brake. NOTE: To start the unit the parking

brake must be engaged.

DISENGAGE Releases the parking brake.

ENGAGE Locks the parking brake

Deck Attachment Lever

The deck attachment lever is used to assist in the process of removing and installing the mower deck to the tractor. See the Attachment Removal and Installation section.

Mower Deck Lift Actuator Switch

Pulling back on the switch will lower the mower deck. Pushing forward on the switch will raise the deck. The ground speed controls levers MUST be in the NEUTRAL positon to raise or lower the mower deck.

Driving the Mower: The mower deck MUST either be positioned in the Operating position or the Service position BEFORE you move the ground speed control levers out of the NEUTRAL position.

Operating the Mower: The mower deck MUST be positioned in the Operating position BEFORE engaging the PTO clutch.

See Positioning the Mower Deck for Service and Positioning the Mower Deck for Operation for the proper positioning of the mower deck.

PTO (Power Take Off) Switch

The PTO switch engages and disengages the mower. Pull UP on the switch to engage, and push DOWN to disengage.

Throttle Control

The throttle controls the engine speed. Move the throttle control forward toward the FAST position to increase the engine speed and back towards the SLOW position to decrease the engine speed. Always operate at FULL throttle.

FAST Speeds up the engine speed.

SLOW Slows down the engine speed.

IMPORTANT NOTE: If you attempt to position the mower deck for service with the PTO switch engaged, the PTO will shut off and remain shut off until the deck is properly positioned for operation and the PTO switch is disengaged and then re-engaged.

Ignition Switch

The ignition switch starts and stops the engine, it has three positions:

OFF Stops the engine and shuts off the electrical

system.

RUN / HEAT

START Cranks the engine for starting

Note: Never leave the ignition switch in the RUN position with the engine stopped-this drains the battery.

Hour Meter

The hour meter measures the number of hours the PTO has been engaged. The hour glass will flash when the hour meter is recording the passage of time. The hour meter has a self-contained power source so that total hours are always visible.

Turning the key to this position prior to starting the engine heats the glow plugs. After the engine starts the engine returns to this position and allows the engine to run and powers the electrical system.

Page 20

Features and Controls

Not for

Reproduction

Glow Plug Indicator

Lamp that indicates that the glow plugs are heating. Hold the ignition key in the “RUN” position until indicator lamp turns off, then turn key to start.

Voltage Gauge

Gauge measures the output voltage of the engine charging system.

Operation

General Operating Safety

Before first time operation:

• Be sure to read all information in the Safety and Operation sections before attempting to operate this unit.

• Become familiar with all of the controls and how to stop the unit.

• Drive in an open area without mowing to become accustomed to the unit.

WARNING

Oil Pressure Indicator

Lamp that indicates a low oil pressure condition.

Water Temperature Gauge

Gauge measures the engine coolant temperature.

WARNING

Operating on steep slopes can be dangerous.

• Never operate on slopes greater than 15°.

• Select slow ground speed before driving onto a slope. Use extra caution when operating on slopes with a rearmounted grass catcher.

• Mow across the face of slopes, not up and down, use caution when changing directions and DO NOT START OR STOP ON A SLOPE.

Do NOT load this zero-turn rider on a trailer or truck using two separate ramps. Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider. This rider has a zero turning radius and the rear wheels could fall off the ramps, or the rider could tip over injuring the operator or bystanders.

WARNING

• Never allow passengers to ride on the unit.

• Before leaving the operator’s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key.

• To reduce fire hazard, keep the engine, tractor and mower free of grass, leaves and excess grease. Do NOT stop or park tractor over dry leaves, grass or combustible materials.

• Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do NOT allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

www.ferrisindustries.com

Page 21

Checks Before Starting

Not for

Reproduction

• Check that crankcase is filled to full mark on the engine

oil dipstick (A, Figure 1). See the engine Operator’s Manual for instructions and oil recommendations.

• Fill the fuel tank (B) with fresh fuel. Refer to engine

manual for fuel recommendations.

• Make sure all nuts, bolts, screws and pins are in place and tight.

• Check the tire pressures. See Check Tire Pressures.

• Check the hydraulic oil tank (C) and make sure that the oil level is up to the FULL COLD mark.

• Adjust the height of the mower deck to the desired position. See Mowing Height Adjustment.

• Adjust the seat position, and make certain you can reach all controls from the operator’s position. See Seat Adjustment (Suspension Seat).

• Make sure that the fuel valves are in the ON position.

• Check the radiator fluid level. See Check Engine Coolant Level.

Operation

Seat Adjustment (Suspension Seat)

S/N: 2014648787 & Below:

In addition to the forward and backward seat adjustment, models equipped with a suspension seat can be adjusted for lumbar support, suspension and back angle.

Forward and Backward Adjustment:

Move the forward / backward seat adjustment lever (A, Figure 2a) away from the seat, position the seat as desired,

and release the lever to lock the seat into position.

Lumbar Adjustment:

Turn the lumbar adjustment knob (B) until the desired amount of lumbar is achieved.

Back Angle Adjustment:

Turn the back angle adjustment knob (C) until the desired amount of back angle is achieved.

Suspension Adjustment:

Turn the suspension adjustment knob (D) until the display scale has a reading that matches the weight of the operator.

Figure 1. Pre-start Checks A. Engine Oil Dipstick B. Fuel Tank Cap C. Hydraulic Oil Fill

Figure 2a. Suspension Seat Adjustment A. Forward / Backward Seat Adjustment Lever B. Lumbar Adjustment Knob C. Back Angle Adjustment Knob D. Suspension Adjustment Knob

Page 22

Operation

Not for

Reproduction

Seat Adjustment

S/N: 2014648788 & Above:

The seat can be adjusted forward and back. Move the seat adjustment lever (A, Figure 2b) to the left, position the seat as desired, and release the lever to lock the seat into position.

Figure 2b. Seat Adjustment A. Seat Adjustment Lever

Check Tire Pressures

Tire pressure should be checked periodically, and maintained at the levels shown in the chart. Note that these pressures may differ slightly from the “Max Inflation” stamped on the side-wall of the tires. The pressures shown provide proper traction, improve cut quality, and extend tire life.

Mowing Height Adjustment

The cutting height adjustment pin (A, Figure 4) controls the mower cutting height. The cutting height is adjustable between 1-1/2” (3,37 cm) and 5” (12,7 cm) in 1/4” (0,64 cm) increments.

1. Turn the ignition key (C) to the RUN position.

2. Press the mower deck lift actuator switch (B) foward

(away from the operator) to remove the pressure from the deck height adjustment pin.

3. Place the deck height adjustment pin in the desired

location.

4. Press the mower deck lift actuator switch backwards

(towards the operator) until contact is made with the deck height adjustment pin. Continue to retract the actuator until the operating position indicator lamp (D) stops flashing and shuts off.

NOTE: The actuator MUST be positioned correctly before attempting to move the ground speed control levers out of their NEUTRAL positions. If the actuator is not positioned as described in the above step the mower’s safety interlock system will cause the engine to shut off.

Deck Caster Tires 25 1,03

Drive Tires 10 0,69

Tractor Caster Tires

Figure 3. Checking Tire Pressure

Tire

Pressure

psi bar

25 1,03

Figure 4. Mowing Height Adjustment A. Cutting Height Adjustment Pin

B. Actuator Deck Height Toggle Switch C. Ignition Switch Key D. Operating Position Indicator Lamp

www.ferrisindustries.com

Page 23

Priming the Fuel System

Not for

Reproduction

Priming the fuel system removes any air bubbles from the fuel system.

WARNING

Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the ignition switch off when changing fuel filter or water separator element. Clean up fuel spills immediately.

The fuel system would only need to be primed under the following conditions:

• Before starting the engine for the first time.

• After running the machine out of fuel and fresh fuel has been added to the fuel tanks.

• After performing maintenance on the fuel system, such as changing the fuel filter or replacing a fuel system component.

To prime the fuel system:

1. Make sure that there is fuel in the fuel tanks and that both fuel tank shut off valves (A, Figure 5) are open (B).

2. Turn the key to the RUN position (not the START position) for 10 to 15 seconds. The electric fuel pump feeds fuel to the system.

Operation

Figure 5. Fuel Shut Off Valve (Bottom Side of Machine Shown) A. Fuel Shut Off Valve Location B. Open Position C. Closed Position

Page 24

Operation

FULL

LOW

Not for

Reproduction

Check Engine Coolant Level

The engine coolant level and quality should be checked before each use, when the engine is cool and off.

WARNING

If engine is warm, DO NOT remove radiator cap. Escaping steam can cause burns. Never remove the radiator cap or radiator reservoir cap while the engine is hot or running. Severe thermal burns or injury can occur by escaping steam or hot coolant.

• Do NOT touch hot radiator or open reservoir when engine is running.

• Stop and allow engine to cool before removing the radiator cap or the reservoir cap and before changing or adding coolant.

The cooling system is a closed type. Never open the radiator cap unless you are flushing the system. Opening the radiator cap may induce air into the cooling system and may cause overheating.

1. Open the hood to gain access to the overflow bottle. See Figure 6.

2. Check the coolant level only at the overflow reservoir (A, Figure 6). The coolant level should be at the LOW (COLD) mark (B).

3. If the coolant level is insufficient, remove the cap (D) from the reservoir and add coolant to the LOW (COLD) mark. See engine owners manual for specific engine coolant specifications.

4. Reinstall the cap.

NOTE: Proper coolant mix is a 50/50 mixture of ethylene glycol and distilled water. See engine owners manual for engine coolant specifications.

Figure 6. Radiator & Overflow Bottle A. Overflow Reservoir B. LOW (Cold) Mark C. FULL (Hot) Mark D. Cap E. Radiator F. Radiator Screen

Change Engine Coolant

See engine owners manual for specific engine coolant procedures. The drain valve is located at the base of the right-hand side of the radiator.

Clean Radiator & Screen

Clean the radiator (E) and radiator screen (F) before each

use, or as required (depending on conditions) to allow proper air-flow through radiator and hydraulic oil cooler.

1. Raise the seat plate.

2. Lift the radiator screen straight up to remove the screen. Flush the screen with water or blow clean with air. Flush the radiator core with water or blow clean with air. See engine owners manual for proper radiator cleaning procedures.

3. Reinstall the radiator screen. Make sure the screen is

4. Lower the seat plate.

fully seated in the carrier.

www.ferrisindustries.com

Page 25

Operation

Not for

Reproduction

Starting the Engine

WARNING

Read the Operator’s Manual before attempting to operate the machine.

• If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES and CONTROLS section, do so now.

• Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.

1. While sitting in the operator’s seat, engage the parking brake by pulling the parking brake lever up, make sure that the PTO switch is disengaged (pressed fully down) and the ground speed control levers are locked in the NEUTRAL position.

2. Set the engine throttle control to the middle position.

3. Insert the key into the ignition switch and turn it to the RUN/HEAT position. Hold the key to turn the glow plug indicator light on and activate the glow plugs.

4. Wait until the glow plug indicator light turns off, then turn the key to START. If the engine does not start immediately, move the throttle control to FULL.

NOTE: Do not crank the engine continuously for more than 30 seconds. Allow the starter motor to cool for two minutes before cranking the engine again.

5. After the engine starts, move the engine throttle control to SLOW. Warm up the engine by running it for at least a minute.

6. Move the throttle to FULL before engaging the PTO switch or driving the machine.

In the event of an emergency the engine can be stopped by simply turning the ignition switch to OFF. Use this method

only in emergency situations. For normal engine shut down follow the procedure given in Stopping the Mower.

Safety Interlock and Mower Deck Positioning Instructions

This unit is equipped with an safety interlock system to help keep the operator safe while running the unit. Please read and understand the SAFETY INTERLOCK SYSTEM and FEATURES AND CONTROLS sections before attempting to drive or operate the mower. In order for the unit to operate properly, the controls must be in the correct positions and used in the correct sequence.

Driving the Mower:

The mower deck MUST either be positioned in the Operating position or the Service position BEFORE you move the ground speed control levers out of the NEUTRAL position. If not, the safety interlock system will cause the engine to shut off. The safety interlock system will prevent you from driving the mower UNTIL the mower deck is positioned in either the Operating or Service position.

Operating the Mower:

The mower deck MUST be positioned in the Operating position BEFORE engaging the PTO clutch. If not, the PTO will NOT engage and remain off UNTIL the mower deck is properly positioned in the operating position, the PTO switch is DISENGAGED and then RE-ENGAGED.

If you raise the mower deck from the operating position with the PTO clutch ENGAGED the PTO will shut off and remain off UNTIL the mower deck is properly positioned in the operating position, the PTO switch is DISENGAGED and then RE-ENGAGED.

Stopping the Mower

1. Returning the ground speed control levers to the middle position will stop rider movement. Pivot the levers outward and lock them in NEUTRAL.

2. Disengage the PTO by pushing down on the PTO switch.

3. Engage the parking brake by pulling the handle up until it locks into position.

4. Move the throttle control to mid-throttle position and allow the engine to cool down for a short while.

5. Turn the ignition key to OFF. Remove the key.

Page 26

Operation

Not for

Reproduction

Zero-Turn Driving Practice

The lever controls of the Zero Turn rider are responsive, and learning to gain a smooth and efficient control of the rider’s forward, reverse, and turning movements will take some practice.

Spending some time going through the maneuvers shown and becoming familiar with how the unit accelerates, travels, and steers — before you begin mowing —is absolutely essential to getting the most out of the Zero Turn rider.

Locate a smooth, flat area of your lawn — one with plenty of room to maneuver. (Clear the area of objects, people and animals before you begin.) Operate the unit at mid-throttle during this practice session (ALWAYS operate at full throttle when mowing), and turn slowly to prevent tire slippage and damage to your lawn.

Smooth Travel

The lever controls of the Zero Turn rider are responsive.

The BEST method of handling the ground speed control levers is in three steps — as shown in Figure

FIRST place your hands onto the levers as shown.

SECOND, to go forward gradually push the levers forward with your palms.

We suggest you begin with the Smooth Travel procedure to the right, and then advance through the forward, reverse, and turning maneuvers.

You must release the parking brake prior to moving the control levers inward.

Basic Driving

Forward Travel Practice

Gradually move both ground speed control levers — evenly FORWARD from neutral. Slow down and repeat.

NOTE: Straight forward travel takes practice. If necessary, top speed can be balance-adjusted — see the Speed Balancing Adjustment in the Adjustments section near the back of this manual.

Forward Travel

THIRD, to speed up move the levers farther forward. To slow down smoothly, slowly move the levers toward neutral.

Figure 7. Move Control Levers Gradually

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both ground speed control levers evenly BACK from neutral. Slow down and repeat.

NOTE: Practice backing up for several minutes before attempting to do so near objects. The rider turns sharply in reverse as well as forward, and backing up straight takes practice.

Reverse Travel

Figure 8. Forward Travel Figure 9. Reverse Travel

www.ferrisindustries.com

Page 27

Operation

Not for

Reproduction

Practice Turning Around a Corner

While traveling forward allow one handle to gradually return back toward neutral. Repeat several times.

NOTE: To prevent pivoting directly on the tire tread, it is best to keep both wheels going at least slightly forward.

Executing Turns

Figure 10. Turning Around a Corner

Practice Turning In Place

To turn in place, “Zero Turn,” gradually move one ground speed control lever forward from neutral and one lever back from neutral simultaneously. Repeat several times.

NOTE: Changing the amount each lever is pulled—forward or back, changes the “pivot point” you turn on.

Turning In-Place

Figure 11. Turning in Place

Advanced Driving

Executing an End-Of-Row Zero Turn

Your Zero Turn Rider’s unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and Y-turn before starting a new row.

For example, to execute a left end-of row zero turn:

1. Slow down at the end of the row.

2. Move the RIGHT ground speed control lever forward slightly while moving the LEFT ground speed control lever back to center and then slightly back from center.

3. Begin mowing forward again.

This technique turns the rider LEFT and slightly overlaps the row just cut—eliminating the need to back up and re-cut missed grass.

As you become more familiar and experienced with operating the Zero Turn rider, you will learn more maneuvers that will make your mowing time easier and more enjoyable.

Remember, the more you practice, the better your control of the Zero Turn will be!

Figure 12. Executing an End-Of-Row Turn

Page 28

Operation

Not for

Reproduction

Mowing

Before mowing, set the cutting height as described in the Operation section.

1. Engage the parking brake. Make sure the PTO switch is disengaged and the ground speed control levers are in the NEUTRAL position.

2. Start the engine (see Starting the Engine).

3. Set the throttle to FULL.

4. Make sure that the mower deck is positioned in the Operating position. (See Positioning the Mower Deck for Operation.)

5. Engage the PTO by pulling up on the PTO switch.

6. Begin mowing. See Mowing Recommendations section for tips on mowing patterns and lawn care. See Troubleshooting section for information on troubleshooting common cutting problems.

7. When finished, shut off the PTO.

8. Stop the engine (see Stopping the Rider and Engine).

Proper Cutting Height

Tall Grass Requires Incremental Cutting

For extremely tall grass, set the cutting height at maximum for the first pass, and then reset it to the desired height and mow a second or third time.

Mowing Recommendations

Several factors can affect how well your machine cuts grass, Following proper mowing recommendations can improve the performance and life of your machine.

Height of Grass

Often cutting height is a matter of personal preference. Typically, you should mow the grass when it is between three and five inches high. The proper cutting height range for a specific lawn will depend upon several factors, including the type of grass, the amount of rainfall, the prevailing temperature, and the lawn’s overall condition.

Cutting the grass too short causes weak, thin grass plants, which are easily damaged by dry periods and pests. Cutting too short is often more damaging than allowing the grass to be slightly higher.

Letting grass grow a bit longer—especially when it is hot and dry—reduces heat build-up, preserves needed moisture and protects the grass from heat damage and other problems. However, allowing grass to grow too high can cause thin turf and additional problems.

Don’t cover the grass surface with a heavy layer of clippings. Consider using a grass collection system and starting a compost pile.

Cut Here On First Pass

Incremental Cutting

Cut Here On Second Pass

Cutting off too much at one time shocks the plant’s growth system and weakens the grass plants. A good rule of thumb

is the 1/3 rule: to cut no more than one third of the grass height, and never more than 1 inch at a time.

The amount of grass you are able to cut in one pass is also effected by the type of mowing system you are using (for example, broadcasting with side discharge decks can process a much larger volume of grass than mulching does).

www.ferrisindustries.com

Page 29

When and How Often to Mow

Not for

Reproduction

The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines:

1. Mow when the grass is between three and five inches high.

2. Mow with sharp blades. Short clippings of grass one inch or shorter decompose more quickly than longer blades. Sharp mower blades cut grass cleanly and efficiently, preventing frayed edges which harm the grass.

3. Mow at time of day when the grass is cool and dry. Late afternoon or early evening often provide these ideal mowing conditions.

4. Avoid mowing after rain or even heavy dew, and never mulch when the grass is wet (moist grass does not mulch well, and clumps beneath the mower deck).

Mowing Patterns

Always start mowing on a smooth, level area.

Operation

Where possible, make one or two passes around the outside of the area discharging the grass INTO the lawn to keep the cut grass off fences and walks.

The size and type of area to be mowed will determine the best mowing pattern to use. Obstructions such as trees, fences and buildings, and conditions such as slopes and grades must also be considered.

1. Cut long straight strips overlapping slightly.

2. Where possible, change patterns occasionally to eliminate matting, graining or a corrugated appearance.

3. For a truly professional cut, mow across the lawn in one direction, then recut the lawn by mowing perpendicular to the previous cut.

Note: Always operate the engine at full throttle when mowing.

If you hear the engine slowing down, you are mowing too fast—using a slower ground speed will improve the cutting efficiency of the blades and prevents many common cutting problems. Use an appropriate ground speed for the thickness and height of the grass you are cutting (3rd gear or slower for manual gear models). If you hear the engine slowing down you are mowing too fast, use a slower ground speed.

The remainder of the mowing should be done in the opposite direction so that the clippings are dispersed OUT onto the area of lawn previously cut.

Mowing Methods

Proper Broadcast Mowing

Broadcasting, or side-discharging, disperses fine clippings evenly over the entire lawn. Many golf courses use this method. Your mower has a deep dish deck to allow freer circulation of clippings so they are broadcast evenly over the lawn.

Engine Speed & Ground Speed for Broadcasting

Always operate the engine at full throttle when mowing. If you hear the engine slowing down, you are mowing too fast—using a slower ground speed will improve the cutting efficiency of the blades and prevents many common cutting problems.

ALWAYS use an appropriate ground speed for the thickness and height of the grass you are cutting (3rd gear or slower for manual gear models). If you hear the engine slowing down you are mowing too fast, use a slower ground speed.

How Much Grass to Cut Off When Broadcasting

Mow when the grass is 3-5 inches long. Do not cut the grass shorter than 2 to 2-1/2 inches. Do not cut off more that 1 inch of grass in a single pass.

Page 30

Operation

Not for

Reproduction

Proper Mulching

Mulching consists of a mower deck which cuts and recuts clippings into tiny particles and which then blows them down INTO the lawn. These tiny particles decompose rapidly into by-products your lawn can use. UNDER PROPER CONDITIONS, your mulching mower will virtually eliminate noticeable clippings on the lawn surface.

NOTE: When mulching under heavy cutting conditions, a rumbling sound may be present and is normal.

Mulching Requires EXCELLENT Mowing Conditions

Mulching mowers cannot function properly if the grass is wet, or if the grass is simply to high to cut. Even more than normal mowing, mulching requires that the grass be dry and the appropriate amount is cut.

Do not use the mower as a mulching mower during the first two or three mowings in the spring. The long grass blades, quick growth, and often wetter conditions are more suitable for broadcasting (side-discharging) or grass bagging operation.

Engine Speed & Ground Speed for Broadcasting

Use full engine throttle matched with a slow ground speed so that clippings will be finely cut. Ground speed while mulching should be HALF of the speed that would be used when broadcasting (side discharging) under similar conditions. Since mulching requires more horsepower than broadcasting, using a slower ground speed is vitally important for proper mulching operation.

How Much Grass to Mulch

The best mulching action typically results from cutting only the top 1/2 inch to 3/4 inch of grass blade. This provides short clippings which decompose properly (much more quickly than longer clippings). The ideal cutting height will vary with climate, time of year, and quality of your lawn. We recommend that you experiment with both the cutting height and ground speed until you achieve the best cut. Start with a high cutting height and using progressively lower settings until you find a cutting height that is matched to your mowing conditions and preferences.

Pushing the Rider by Hand

1. Disengage the PTO, engage the parking brake, turn the ignition OFF, and remove the key.

2. Locate the hydraulic release valves (A, Figure 13) on the bottom side of the hydraulic pumps.

3. To disengage the pumps (free-wheel position), turn the hydraulic release valves located on the pumps COUNTER-CLOCKWISE a maximum of 2 full turns.

4. Disengage the parking brake.

The rider can now be pushed by hand.

5. After moving the rider, re-engage the pumps (drive position) by turning the release valves CLOCKWISE and tighten to 80-120 in. lbs. (9.04 - 13.56 Nm) of torque.

NOTICE

• Towing the unit will cause hydraulic pump and wheel

• Do NOT tow rider.

• Do NOT use another vehicle to push or pull this unit.

motor damage.

Mulching Action

Figure 13. Hydraulic System By-Pass A. Hydraulic Release Valve (right-hand pump shown)

www.ferrisindustries.com

Page 31

Raise and Lower the Roll Bar

Not for

Reproduction

Operation

WARNING

Avoid serious injury or death from roll over.

• Keep the roll bar in the raised position and use seat belt.

• There is no roll over protection when the roll bar is down.

• Lower the roll bar only when necessary and NEVER remove it.

• Do NOT use the seat belt when the roll bar is down.

• Raise the roll bar as soon as clearance permits.

• Do NOT jump off if mower tips.

To Lower the Roll Bar:

1. Pull the hair pin clips (A, Figure 14) out of the retainer pins (B).

2. Push or pull the top of the roll bar (C) forward against the rubber stops (D) and remove the retainer pins (B).

3. Lower the roll bar and reinstall the retainer pins and hair pin clips to secure the roll bar in the down position (see insert, Figure 14).

Figure 14. Raise & Lower the Roll Bar A. Hair Pin Clip B. Retainer Pin C. Roll Bar D. Rubber Stop

To Raise the Roll Bar:

1. Pull the hair pin clips (A) out of the retainer pins (B) and remove the retainer pins.

2. Raise the roll bar (C) until the rubber stops (D) contact the upright tubes.

3. Push or pull the top of the roll bar forward against the rubber stops and reinstall the retainer pins and hair pin clips to secure the roll bar in the raised position.

Page 32

Operation

Not for

Reproduction

Attachment Removal and Installation Procedure

Positioning the Mower Deck for Service

1. Park the machine on a smooth, level surface such as a concrete floor. Engage the parking brake, disengage the PTO, and turn off the ignition key.

2. Turn the ignition key to the RUN position and push the mower deck lift actuator switch forward (away from the operator’s position) to extend the actuator until you hear a ratcheting noise.

3. Move the cutting height adjustment pin to the lowest cutting position.

4. Remove the pins with lanyards (B, Figure 15) from the attachment lift arms (A).

5. Retract the actuator completely by pulling the mower deck lift actuator switch backwards (towards the operator’s position).

6. If you are not removing the deck, proceed to Positioning

the Mower Deck for Operation.

Removing the Attachment

1. Disconnect the two (2) spring links (C, Figure 15) from the tractor connection point (F).

2. Extend the actuator until the front wheels contact the ground.

3. Reinstall the pins with lanyards through the rear hole (G) of the attachment latches (D).

4. Extend the actuator until the load is removed from the actuator. Turn the ignition key to the OFF position.

5. Raise the seat and disconnect the actuator wire harness (A, Figure 16) on the right side of the machine by rotating the connector dial (B) and pulling apart.

6. Pull the mower deck end of the actuator wire harness from the tractor.

7. Disconnect the rear of the actuator (A, Figure 17) from the tractor by removing the pin with lanyard (B).

8. Locate the drive shaft (A, Figure 18) under the machine and disconnect it by pulling the drive shaft collar (B) toward the universal joint.

9. Pull the deck attachment lever (E, Figure 15) up and back.

10. Back the tractor away from the mower deck.

CA B D E

Figure 15. Attachment Lift Arms A. Attachment Lift Arms B. Pin with Lanyard C. Spring Links D. Attachment Latches E. Deck Attachment Lever F. Tractor Connection Point G. Attachment Latch in Raised Position

Figure 16. Actuator Wire Harness A. Actuator Wire Harness B. Connector Dial

www.ferrisindustries.com

Page 33

Installing the Attachment

Not for

Reproduction

1. Remove the pins with lanyards (B, Figure 15) from the rear holes of the attachment latches (D).

2. Drive the tractor into the mower deck.

3. Push the deck attachment lever (E) forward and down. Make sure the attachment latches latch into place.

4. Reconnect the actuator to the tractor.

5. Reconnect the actuator wire harness (A, Figure 16) to the main harness of the tractor.

6. Reconnect the drive shaft.

7. Retract the actuator completely.

8. Reconnect the two (2) spring links (C, Figure 15) to the tractor.

Positioning the Mower Deck for Operation

1. Extend the actuator fully.

2. Install the pins with lanyards into the attachment lift arms (A, Figure 15).

3. Reposition the cutting height adjustment pin to the desired cutting height.

4. Retract the actuator until contact is made with the cutting height adjustment pin (A, Figure 19). Continue to retract the actuator until the operating position indicator lamp (B) stops flashing and shuts off.

Figure 17. Actuator A. Actuator B. Pin with Lanyard

Figure 18. Drive Shaft A. Drive Shaft Universal Joint B. Drive Shaft Coupler

Operation

Figure 19. Mowing Height Adjustment A. Cutting Height Adjustment Pin B. Operating Position Indicator Lamp

Page 34

Maintenance

Not for

Reproduction

Maintenance Schedule

The following schedule should be followed for normal care of your rider and mower. You will need to keep a record of your operating time. Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter.

UNIT MAINTENANCE

Before Each Use

Check Safety Interlock System

Check Rider Brakes

Check Rider / Mower for Loose Hardware

Every 100 Hours or Annually*

Check Gearbox Oil Level***

Clean Deck & Check / Replace Mower Blades

Lubricate Rider & Mower**

Clean Battery & Cables

Check Tire Pressure

Check Hydraulic Oil**

Every 250 Hours or Annually*

Change Hydraulic Oil Filter**

* Whichever comes first. ** More often in hot (over 85° F; 30° C) weather or

dusty operating conditions

*** Change gearbox oil after first 100 hrs. and every

500 hrs. thereafter (See Gearbox Maintenance).

ENGINE MAINTENANCE

Before Each Use

Check Engine Oil Level

Check Engine Coolant Level

Check & Clean Radiator Screens

Every 25 Hours

Check / Clean Cooling Fins & Intake**

Check Fuel Filter / Drain Water Seperator

Refer to Engine Manufacturer’s Owner’s Manual

Service Air Filter

Change Oil & Filter*

Check / Replace Spark Plugs

Annually

Change Engine Coolant

* Change original engine oil after the first 5 hours of

operation.

** More often in hot (over 85° F; 30° C) weather or

dusty operating conditions

www.ferrisindustries.com

Page 35

Ground Speed Control Lever Adjustment

Not for

Reproduction

The control levers can be adjusted in three ways. The alignment of the control levers, the placement of the levers (how close the ends are to one another) and the height of the levers can be adjusted.

To Adjust the Handle Alignment

Loosen the ground speed control lever mount bolts (D, Figure 20) and pivot the lever(s) (C) to align with each other.

To Adjust the Handle Placement

Loosen the jam nuts and adjust the placement bolt (B) in or out to properly adjust the lever end spacing.

To Adjust the Handle Height

Remove the mounting hardware (D) and reposition the handle either up or down from its original position. You will need to readjust the handle alignment as described above.

Maintenance

Figure 20. Top Speed Adjustment A. Top Speed Adjustment Bolt B. Handle Placement Hardware C. Alignment Hardware D. Ground Speed Control Lever Mount Bolts

Speed Balancing Adjustment

If the rider veers to the right or left when the ground speed control levers are in the maximum forward position, the top speed of each of these levers can be balanced by adjusting the top speed adjustment bolt(s) (A, Figure 20). Only adjust the speed of the wheel that is traveling faster.

To Reduce the Speed of the Faster Wheel

1. Loosen the securing nut.

2. Turn the top speed adjustment bolt COUNTERCLOCKWISE to reduce the speed.

3. Retighten the securing nut when adjustment is complete.

WARNING

Do NOT adjust the tractor for a faster overall speed forward or reverse than it was designed for.

Page 36

Maintenance

Not for

Reproduction

Storage

Temporary Storage (30 Days Or Less)

Remember, the fuel tank will still contain some fuel, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation.

Here is a checklist of things to do when storing your unit temporarily or in between uses:

• Keep the unit in an area away from where children may come into contact with it. If there’s any chance of unauthorized use remove the ignition key.

• If the unit can’t be stored on a reasonable level surface, chock the wheels.

• Clean all grass and dirt from the mower.

• If temperature is expected to drop below 35 degrees, refer to Long Term Storage, Item 2.

Long Term Storage (Longer Than 30 Days)

Before you store your unit for the off-season, read the Maintenance and Storage instructions in the Safety Rules section, then perform the following steps:

1. Drain crankcase oil while engine is hot and refill with a grade of oil that will be required when unit is used again.

2. Use an Antifreeze tester to check the cooling system’s level of protection. Read the instructions on the Antifreeze container for the appropriate ratio of water to Antifreeze for your geographical area.

3. Prepare the mower deck for storage as follows:

a. Remove mower deck from the unit.

b. Clean underside of mower deck.

c. Coat all bare metal surfaces with paint or light coat

of oil to prevent rusting.

4. Clean external surfaces and engine.

5. Prepare engine for storage. See engine owner’s manual.

6. Clean any dirt or grass from cylinder head, engine housing and air cleaner element.

7. Cover air cleaner and exhaust outlet tightly with plastic or other waterproof material to keep out moisture, dirt and insects.

8. Completely grease and oil unit as outlined in the Regular Maintenance section.

9. Clean up unit and apply paint or rust preventative to any areas where paint is chipped or damaged.

10. Be sure the battery is filled to the proper level with water and is fully charged. Battery life will be increased if it is removed, put in a cool, dry place and fully charged about once a month. If battery is left in unit, disconnect the negative cable.

11. Drain fuel system completely or add a diesel fuel stabilizer to the fuel system. If you have chosen to use a fuel stabilizer and have not drained the fuel system, follow all safety instructions and storage precautions in this manual to prevent the possibility of fire from the ignition of diesel fumes. Remember, diesel fumes can travel to distant sources of ignition and ignite, causing risk of explosion and fire.

WARNING

Never store the unit, with diesel fuel in engine or fuel tank, in a heated shelter or in enclosed, poorly ventilated enclosures. Diesel fumes may reach an open flame, spark or pilot light (such as a furnace, water heater, clothes dryer, etc.) and cause an explosion.

Handle diesel fuel carefully. It is highly flammable and careless use could result in serious fire damage to your person or property.

Drain fuel outdoors into an approved container and away from open flame or sparks.

NOTE: Diesel fuel, if permitted to stand unused for extended periods (30 days or more), may develop gummy deposits which can adversely affect the fuel pump and injector tubes and cause engine malfunction. To avoid this condition, add a diesel fuel stabilizer to the fuel tank and run the engine a few minutes, or drain all fuel from the unit before placing it in storage.

Starting After Long Term Storage

Before starting the unit after it has been stored for a long period of time, perform the following steps.

1. Remove any blocks from under the unit.

2. Install the battery if it was removed.

3. Unplug the exhaust outlet and air cleaner.

4. Fill the fuel tank with fresh fuel. See engine manual for recommendations.

5. See engine owner’s manual and follow all instructions for preparing engine after storage.

6. Check crankcase oil level and add proper oil if necessary. If any condensation has developed during storage, drain crankcase oil and refill.

7. Inflate tires to proper pressure. Check fluid levels.

8. Start the engine and let it run slowly. DO NOT run at high speed immediately after starting. Be sure to run engine only outdoors or in well ventilated area.

Diesel Fuel Recommendations

Fuel companies provide fuel tailored to meet the existing weather conditions. These fuels change at the start of the predominant season according to regional weather trends.

Winter fuels are tailored to give ease of starting for cold weather. Summer fuel may be somewhat heavier than winter fuel resulting in slightly better fuel economy and power. Spring and fall fuel is an average blend between winter and summer blend.

For these reasons an effort should be made to purchase fuels in such quantities that they are not carried over into the next season. Using the wrong blend of fuel can cause problems with the engine.

Refer to the engine manufacturer’s manual for specific fuel recommendations.

www.ferrisindustries.com

Page 37

Specifications

Not for

Reproduction

Specifications

NOTE: Specifications are correct at time of printing and are subject to change without notice.

ENGINE

30 Gross HP¹ Yanmar

Make Yanmar

Model 3TNV82A-BDFS

Displacement 81.22 Cu. in (1331 cc)

Electrical System 12 volt, 40 amp. Alternator,

Battery 500 CCA

Oil Capacity 5.8 US Qt (5,5 L) w/ filter

¹Power Ratings: Actual sustained equipment horsepower likely to be lower due to operating limitations and environmental factors.

CHASSIS

Fuel Tank Capacity: 12 gallons (45,2 L) total

Drive Tires Tire Size: 24 X 12 - 12

Inflation Pressure: 10 psi (0,69 bar)

Front Caster Tires Tire Size: 11 x 4.00 - 5

Inflation Pressure: 25 psi (1,72 bar)

Rear Caster Tires Tire Size: 13 x 6.50 - 6

Inflation Pressure: 25 psi (1,72 bar)

TRANSMISSIONS

LH Pump: Hydro-Gear: PR-2KBQ-GV1F

RH Pump: Hydro-Gear: PR-2HBQ-GV1F

(S/N: 2014473229 & Below):

LH Wheel Motor: Parker: TF0280LS080AAK2

RH Wheel Motor: Parker: TF0280LS081AAK2

(S/N: 2014473230 & Above):

LH Wheel Motor: Parker: TF0000LS080AAKZ

RH Wheel Motor: Parker: TF0000LS080AAKZ

Type Pump and Wheel Motor

Hydraulic Fluid Mobil 1™ 15W-50 oil OR

Castrol Syntec™ 5W-50 oil

Speeds @ 3000 rpm Forward: 0-10 MPH (0-16,09 km/h)

Reverse: 0-5 MPH (0-8,05 km/h)

DIMENSIONS

Overall Length 115.5” (293,4 cm)

Overall Width 73” (185 cm) - deflector down

61.5” (156 cm) - deflector up

Height 69” (175,3 cm) w/ Roll Bar up

57” (177,8 cm) w/ Roll Bar down

Weight (apx.) 1514 lbs (687 kg)

Page 38

Operator Safety

Not for

Reproduction

INSTRUCTIONS

1. Fold this page along

the dotted line indicated

above.

2. Align the left edge of this

guide with a vertical tree,

a power line pole, a fence

post, or any vertical

structure.

3. Compare the angle of the

fold with the angle of the

hill.

FOLD ALONG APPROPRIATE DOTTED LINE

COMPARE THE ANGLE

OF THE FOLD TO THE

ANGLE OF THE SLOPE

THIS IS A 15 DEGREE SLOPE

SLOPE INDENTIFICATION GUIDE

THIS IS A 10 DEGREE SLOPE

(TREE, POLE, FENCE POST, BUILDING, ETC)

ALIGN THIS EDGE WITH A VERTICAL SURFACE

www.ferrisindustries.com

Page 39

Ferris Industries - a division of Briggs & Stratton Power Products Group, LLC.

Not for

Reproduction

Owner’s Limited Warranty Information

(Effective 04/28/2004)

Thank you for purchasing Ferris commercial mowing equipment. Please take a few minutes to read this limited warranty information. It contains all the information you will need to have your Ferris mower repaired in the unlikely event that a breakdown covered by this limited warranty should occur.

Owner’s Responsibilities - As a condition to our obligations under this limited warranty, you shall have read the operator’s manual and you shall have completed and submitted to Ferris, within 20 days from the date of purchase, the Ferris Product Registration. You must properly service and maintain your Ferris product as described in the operator’s manual. Such routine maintenance, whether performed by a dealer or by you, is at your expense. The Ferris equipment, including any defective part covered by this limited warranty, must be returned to an authorized Ferris dealer within the warranty period for warranty service. This limited warranty extends only to equipment operated under normal conditions and in accordance with Ferris’ instructions.

Warranty Start Date - The limited warranty coverage begins on the day you buy your new Ferris commercial mowing equipment. An authorized Ferris dealer will assist you in filling out a Ferris Product Registration with specific information for the model you purchase and your personal information, which must be returned to Ferris.

Limited Warranty - The limited warranty, set forth below, is a written guarantee by Ferris, during the warranty period, to repair or replace parts which have a substantial defect in materials or workmanship. The warranty is “limited” because it is for a specified period of time, applies to the original purchaser only, and is subject to other restrictions.

FERRIS LIMITED WARRANTY

Ferris Industries (Ferris) warrants, in accordance with the provisions below, to the original purchaser only, for the periods described below that the commercial mower shall be free from substantial defects in material or workmanship under normal use and service. If you wish to file a claim under this limited warranty, you must provide prompt notice of your claim to an authorized Ferris dealer during the warranty period. Ferris’ obligation under this limited warranty is, at Ferris’ option, to repair or replace any part or parts of the mower, which, in the judgment of Ferris, are found to be defective and covered by this limited warranty. An authorized Ferris dealer will repair or replace the defective part or parts, at the dealer’s place of business, at no charge for the labor or parts. This limited warranty applies only to mowers sold in the United States and Canada and is subject to the following limitations.

Covered Parts Warranty Period

All Mowers 2-years (24 months) from date of retail purchase by the original purchaser for parts & labor (90 days for rental mowers) (Except as noted below*)

*Belts, Tires, Brake Pads 90 days from date of retail purchase by the original purchaser And Hoses, Battery, Blades

*Attachments 1 year from date of retail purchase by the original purchaser

*Engine If the engine manufacturer provides any warranty on the mower’s engine, Ferris will assign that warranty to the original purchaser of the mower if such assignment is reasonably practicable. Please refer to the engine manufacturer’s warranty statement, if any, that is included in the owner’s packet. We are not authorized to handle warranty adjustments or repairs on engines. Ferris offers NO WARRANTY on mower engines. Ferris does not guarantee or represent that any engine manufacturer will comply with the terms of its warranty.

Items and Conditions Not Covered

This warranty does not cover, and Ferris makes NO WARRANTY regarding, the following:

• Mowers or their parts if a complete and accurate Ferris Product Registration has not been received by Ferris.

• Loss or damage to person or property other than that expressly covered by the terms of this limited warranty.

• Pickup and delivery charges and risk of loss or damage in transit to and from any authorized Ferris dealer.

• Any damage or deterioration due to normal use, wear and tear, or environmental or natural elements, or exposure.

• Cost of regular maintenance service or parts, such as but not limited to, filters, fuel, lubricants, tune-up parts, and adjustments.

• Claims arising due to failure to follow Ferris’ written instructions, or improper storage or maintenance.

• Any repairs necessary due to use of parts, accessories or supplies, including gasoline, oil or lubricants, incompatible with the mowing equipment, or other than as recommended in the operator’s manual or other written operational instructions provided by Ferris.

• Use of non-Ferris approved parts or accessories.

• Any overtime or other extraordinary repair charges or charges relating to repairs or replacements.

• Rental of like or similar replacement equipment during the period of any warranty, repair or replacement work.

• Loss of revenue, time or use of the mowing equipment.

• Travel, telephone or other communication charges.

• Damage from continued use of defective mowing equipment.

• Freight charges on replacement parts.

• Any mowing equipment or part which, in the judgment of Ferris, has been altered or tampered with in any way or has been subjected to misuse, abuse, abnormal usage, unauthorized repair, neglect or accident, damage in transit, or has had the serial numbers altered, effaced or removed.

• Any equipment, part or item not mentioned under “Covered Parts,” above.

General Conditions

Ferris is continually striving to improve its products, and therefore reserves the right to make improvements or changes without incurring any obligation to make changes or additions to products sold previously. Any oral or written description of Ferris products is for the sole purpose of identifying the products and shall not be construed as an express warranty. No warranty claim shall give rise to a right for the purchaser to cancel or rescind any sale. No person is authorized to make any warranty or assume for Ferris any liability not strictly in accordance with this limited warranty. Any assistance Ferris provides to or procures for the purchaser outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of the terms, limitations or exclusions of this limited warranty, nor will such assistance extend or revive the limited warranty. Ferris will not reimburse the purchaser for any expenses incurred by the purchaser in repairing, correcting or replacing any defective products except for those incurred with Ferris’ prior written permission and in accordance with this limited warranty.

Ferris’ sole and exclusive liability with respect to this limited warranty, and the purchaser’s exclusive remedy, shall be repair or replacement as set forth herein. All warranty work must be performed by an authorized Ferris dealer using only Ferris approved replacement parts. FERRIS SHALL

HAVE NO LIABILITY FOR ANY OTHER COST, LOSS OR DAMAGE, INCLUDING BUT NOT LIMITED TO, ANY INCIDENTAL, COMPENSATORY, INDIRECT, PUNITIVE, SPECIAL OR CONSEQUENTIAL LOSS OR DAMAGE. FERRIS’ AGGREGATE LIABILITY WITH RESPECT TO A DEFECTIVE PRODUCT OR PART SHALL BE LIMITED TO AN AMOUNT EQUAL TO THE MONIES PAID BY THE PURCHASER FOR THAT DEFECTIVE PRODUCT OR PART. THIS LIMITED WARRANTY, AND FERRIS’ OBLIGATIONS HEREUNDER, ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. FERRIS SHALL NOT BE LIABLE TO THE PURCHASER, OR TO ANYONE CLAIMING UNDER THE PURCHASER, FOR ANY OTHER OBLIGATIONS OR LIABILITIES, INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING OUT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT LIABILITY, WITH RESPECT TO FERRIS PRODUCTS OR FERRIS’ ACTS OR OMISSIONS OR OTHERWISE.

It is the express wish of the parties that this agreement and any related documents be drafted in English. Il est la volonté expresse des parties que cette convention et tous les documents s’y rattachent soient rédigés en anglais.

Page 40

OPERATOR’S

Not for

Reproduction

MANUAL

F800X Series

Zero-Turn Riding Mower

Briggs & Stratton Power Products Group, LLC.

5375 North Main Street Munnsville, NY 13409 800-933-6175 www.Ferrisindustries.com

Ferris F800X Series, 5900911, 5900940, F800XY30DCE, F800XY30D ANSI-EXPORT Operator's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual