Ferris CCW36 Series, CCWKAV1536RDCE, CCWKAV1536CE, CCWKAV1636RDCE, CCWKAV1636CE Operator's Manual

OPERATOR’S

Not for

Reproduction

MANUAL

CCW36 Series

Walk-Behind Mowers

Model Number: Description

5900749 CCWKAV1536RDCE - 36” Rear Discharge Mower Deck Export

5900758 CCWKAV1536CE - 36” Side Discharge Mower Deck Export
5900987 CCWKAV1636RDCE - 36” Rear Discharge Mower Deck Export
5900988 CCWKAV1636CE - 36” Side Discharge Mower Deck Export
5900542 CCWKAV1536CE - 36” Side Discharge Mower Deck Export
5900541 CCWKAV1536RDCE - 36” Rear Discharge Mower Deck Export

Briggs & Stratton Power Products Group, LLC

5375 North Main Street
Munnsville, NY 13409
800-933-6175

5102303

Revision D

Thank you for purchasing this quality-built FERRIS product. We’re pleased that you’ve placed your confidence in the FERRIS

Not for

Reproduction

brand. When operated and maintained according to the instructions in this manual, your FERRIS product will provide many years
of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with this machine and how to
avoid them. This machine is designed and intended to be used and maintained according to the manual and operated by trained
professionals for finish cutting of established lawns and is not intended for any other purpose. It is important that you read and
understand these instructions thoroughly before attempting to start or operate this equipment.

Save these original instructions for future reference.

PRODUCT REFERENCE DATA

Unit Model Number Unit Serial Number

Mower Deck Model Number Mower Deck Serial Number

Dealer Name Date Purchased

ENGINE REFERENCE DATA

Engine Make Engine Model

Engine Type/Spec Engine Code Serial Number

The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth
defects, or other reproductive harm.

Battery posts, terminals, and related accessories contain
lead and lead compounds – chemicals known to the State
of California to cause cancer and reproductive harm. Wash
hands after handling.

Briggs & Stratton Power Products Group
Copyright © 2011 Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.

FERRIS is a trademark of Briggs & Stratton Corporation, LLC.
Milwaukee, WI, USA.

Contact Information:

Briggs & Stratton Power Products Group, LLC.
5375 N. Main St.
Munnsville, NY 13409-4003
[phone]
www.ferrisindustries.com

WARNING

WARNING

Table of Contents

Not for

Reproduction

Operator Safety .................................................... 2

Safety Rules and Information ...........................................2

Safety Decals ....................................................................8

CE Safety Icons ................................................................9

Safety Interlock System ..................................................10

Safety Icons ....................................................................10

Features & Controls ..............................................11

Identification Numbers ...................................................11

Control Functions ...........................................................12

Operation...........................................................14

General ...........................................................................14

Checks Before Starting ...................................................14

Starting The Engine ........................................................14

Stopping The Mower ......................................................14

Checking Tire Pressures .................................................15

Pushing the Unit by Hand ...............................................15

Cutting Height Adjustment ..............................................16

Driving the Mower ..........................................................17

Mowing ...........................................................................18

Mowing Recommendations ............................................18

Mowing Methods ............................................................19

Specifications .....................................................21

Slope Identification Guide.......................................22

NOTE: In this manual, “left” and “right” are referred to as seen
from the operating position.

1

Safety Rules & Information

Not for

Reproduction

Read the Manual

Operating Safety

Congratulations on purchasing a superior-quality piece of
lawn and garden equipment. Our products are designed and
manufactured to meet or exceed all industry standards for safety.

Do not operate this machine unless you have been trained.
Reading and understanding this operator’s manual is a way to
train yourself.

Power equipment is only as safe as the operator. If it is misused,
or not properly maintained, it can be dangerous! Remember, you
are responsible for your safety and that of those around you.

Use common sense, and think through what you are doing. If
you are not sure that the task you are about to perform can be
safely done with the equipment you have chosen, ask a
professional: contact your local authorized dealer.

The operator’s manual contains important safety
information you need to be aware of BEFORE you
operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the
product’s features and controls, and maintenance
information is included to help you get the most out of
your equipment investment.

Be sure to completely read the Safety Rules and
Information found on the following pages. Also
completely read the Operation section.

Children

Tragic accidents can occur with children. Do
not allow them anywhere near the area of
operation. Children are often attracted to the
unit and mowing activity. Never assume that
children will remain where you last saw them.
If there is a risk that children may enter the
area where you are mowing, have another
responsible adult watch them.

2

Safety Rules & Information

Not for

Reproduction

Slope Operation

You could be seriously injured if you use this unit on too steep of
a slope. Using the unit on a slope that is too steep where you do
not have adequate footing and unit traction (and control) can cause
you to lose control and possibly slip and fall or roll the unit over.

Always mow across slopes, not up and down (you could slip and
fall.)

Also, note that the surface you are on can greatly impact your
ability to safely operate this machine. Wet grass or soft soil can
seriously affect your footing and traction of the unit. Do not
operate on slopes that are slippery, wet, or have soft soil.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and
throw debris that could seriously injure a bystander. Be sure to clean
up the area to be mowed and remove objects that could be thrown by
the blade BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge
guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If
someone does enter the area, shut the unit off immediately until they
leave.

This equipment has many moving parts that can injure
you or someone else. However, if you stay in the
operator zone (area behind the handles and controls),
and follow the safety rules in this operator’s manual, the
unit is safe to operate.

The mower deck has spinning mower blades that can
amputate hands and feet. Do not allow anyone near the
unit while it is running! Keep safety devices (guards,
shields, and switches) in place and working.

To help you, the operator, use this equipment safely, it
is equipped with an operator-present safety system. Do
NOT attempt to alter or bypass the system. See your
dealer immediately if the system does not pass all the
safety interlock system tests found in this manual.

Moving Parts

3

Safety Rules & Information

Not for

Reproduction

Fuel and Maintenance

Always disengage all drives, shutoff the engine and
remove the key before doing any cleaning, refueling or
servicing.

Gasoline and its vapors are extremely flammable. Do not
smoke while operating or refueling. Do not add fuel while
engine is hot or running. Allow engine to cool for at least
3 minutes prior to adding fuel.

Do not add fuel indoors, in an enclosed trailer, garage or
other enclosed area that is not well ventilated. Gasoline
spills should be cleaned up promptly and before operation
begins.

Gasoline should be stored only in sealed containers
approved for fuel.

Proper maintenance is critical to the safety and
performance of your unit. Keep the unit free of
grass, leaves and excess oil. Be sure to perform the
maintenance procedures listed in this manual, especially
periodically testing the safety system.

Enclosed Areas

Only operate this unit outdoors and
away from unventilated areas such as
inside garages or enclosed trailers.
The engine emits poisonous carbon
monoxide gas and prolonged exposure
in an enclosed area can result in
serious injury or death.

4

Safety Rules & Information

Not for

Reproduction

Read these safety rules and follow them closely. Failure to obey these rules could result in loss
of control of unit, severe personal injury or death to you, or bystanders, or damage to property or
equipment. This mowing deck is capable of amputating hands and feet and throwing objects.
The triangle in text signifies important cautions or warnings which must be followed.

TRAINING

1. Read, understand, and follow all instructions in
the manual and on the unit before starting. If the
operator(s) or mechanic(s) can not read English
it is the owner’s responsibility to explain this
material to them.

2. Become familiar with the safe operation of the
equipment, operator controls, and safety signs.

3. All operators and mechanics should be trained.
The owner is responsible for training the users.

4. Only allow responsible adults, who are familiar
with the instructions, to operate the unit.

5. Never let children or untrained people operate
or service the equipment. Local regulations may
restrict the age of the operator.

6. The owner/user can prevent and is responsible
for accidents or injuries occurring to themselves,
other people or property.

7. Data indicates that operators, age 60 years and
above, are involved in a large percentage of riding
mower-related injuries. These operators should
evaluate their ability to operate the riding mower
safely enough to protect themselves and others
from serious injury.

PREPARATION

1. Evaluate the terrain to determine what
accessories and attachments are needed to
properly and safely perform the job. Use only
accessories and attachments approved by the
manufacturer.

2. Wear appropriate clothing including safety shoes,
safety glasses and ear protection. Long hair,
loose clothing or jewelry may get tangled in
moving parts.

3. Inspect the area where the equipment is to be
used and remove all objects such as rocks, toys
and wire, which can be thrown by the machine.

4. Use extra care when handling gasoline and
other fuels. They are flammable and vapors are
explosive.

a) Use only an approved container.

b) Never remove fuel cap or add fuel with the

engine running. Allow engine to cool before
refueling. Do not smoke.

c) Never refuel or drain the machine indoors.

5. Check that operator’s presence controls, safety
switches and shields are attached and functioning
properly. Do not operate unless they are
functioning properly.

OPERATION

1. Never run an engine in an enclosed area.

2. Mow only in the daylight or with good artificial
light, keeping away from holes and hidden
hazards.

3. Be sure all drives are in neutral and parking brake
is engaged before starting engine. Only start
engine from the operator’s position. Use seat
belts if provided.

4. Be sure of your footing while using pedestrian
controlled equipment, especially when backing up.
Walk, don’t run. Reduced footing could cause
slipping.

5. Slow down and use extra care on hillsides. Be
sure to travel in the recommended direction on
hillsides. Turf conditions can affect the machines
stability. Use caution when operating near drop­offs.

6. Do not mow in reverse unless absolutely
necessary. Always look down and behind before
and while traveling in reverse.

7. Be aware of the mower discharge direction and do
not point it at anyone. Do not operate the mower
without either the entire grass catcher or the
deflector in place.

8. Slow down and use caution when making turns
and when changing directions on slopes.

9. Never raise deck with the blades running.

10. Never leave a running unit unattended. Always
disengage the PTO, set parking brake, stop
engine, and remove keys before dismounting.
Keep hands and feet away from the cutting units.

11. Turn off the PTO switch to disengage the blades
when not mowing.

12. Never operate with guards not securely in place.
Be sure all interlocks are attached, adjusted
properly and functioning properly.

13. Never operate with the discharge deflector raised,
removed or altered, unless using a grass catcher.

14. Do not change the engine governor setting or
overspeed the engine.

15. Stop on level ground, lower implements,
disengage drives, engage parking brake, shut off
engine before leaving the operator’s position for
any reason including emptying the grass catchers
or unclogging the chute.

16. Stop equipment and inspect blades after striking
objects or abnormal vibration occurs. Make
necessary repairs before resuming operations.

17. Keep hands and feet away from the cutting units.

18. Look behind and down before backing up to be
sure of a clear path.

19. Never carry passengers and keep pets and
bystanders away.

20. Do not operate the unit while under the influence
of alcohol or drugs.

21. Slow down and use caution when making turns
and crossing roads and sidewalks. Stop blades if
not mowing.

22. Use care when loading or unloading the machine
into a trailer or truck.

5

Safety Rules & Information

Not for

Reproduction

23. Use care when approaching blind corners, shrubs,
trees or other objects that may obscure vision.

24. To reduce fire hazard, keep unit free of grass,
leaves & excess oil. Do not stop or park over dry
leaves, grass or combustible materials.

WARNING

It is a violation of California Public Resource
Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered
or grass-covered land unless the exhaust
system is equipped with a spark arrester,
as defined in Section 4442, maintained in
effective working order. Other states or federal
jurisdictions may have similar laws. Contact
an Authorized Service Dealer to obtain a spark
arrester designed for the exhaust system
installed on this engine.

25. OSHA regulations may require the use of hearing
protection when exposed to sound levels greater
than 85 dBA for an 8 hour time period.

CAUTION

This machine produces sound levels
in excess of 85 dBA at the operator’s
ear and can cause hearing loss
though extended periods of exposure.

Wear hearing protection when operating this
machine.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or
death. All slopes require extra caution. If you cannot
back up the slope or if you feel uneasy on it, do not
drive on it.

WARNING

Operating on steep slopes can cause sliding
and loss of steering, control and rollover.

Select slow ground speed before driving onto
slope. Use extra caution when operating on
slopes with rear-mounted grass catchers.

Mow across the face of slopes, not up and
down, use caution when changing directions
and DO NOT START OR STOP ON SLOPE.

6. Keep all movement on the slopes slow and
gradual. Do not make sudden changes in speed
or direction.

7. See your authorized dealer for recommendations
of available weights to improve stability.

Do Not

1. Avoid starting, stopping, or turning on a slope.
If tires lose traction (i.e. machine stops forward
motion on a slope), disengage the blade(s) (PTO)
and drive slow off the slope.

2. Do not turn on slopes unless necessary, and then,
turn slowly.

3. Do not mow near drop-offs, ditches, or
embankments. The operator could lose footing or
balance or mower could suddenly turn over if a
wheel is over the edge of a cliff or ditch, or if an
edge caves in.

4. Do not mow on wet grass. Reduced footing or
traction could cause sliding.

5. Do not mow excessively steep slopes.

6. Do not use grass catcher on steep slopes.

CHILDREN

Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted
to the unit and the mowing activity. Never assume that
children will remain where you last saw them.

1. Keep children out of the mowing area and under
the watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind
and down for small children.

4. Never allow children to operate the unit.

5. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.

EMISSIONS

1. Engine exhaust from this product contains
chemicals known, in certain quantities, to cause
cancer, birth defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period
and Air Index information on the engine emissions
label.

IGNITION SYSTEM (GASOLINE MODELS)

1. This spark ignition system complies with Canadian
ICES-002.

Do

1. Mow across slopes, not up and down.

2. Remove obstacles such as rocks, tree limbs, etc.

3. Watch for holes, ruts, or bumps. Uneven terrain
could overturn the unit. Tall grass can hide
obstacles.

4. Use slow speed. Choose a slow speed so that

5. Use extra care with grass catchers or other

6

you will not have to stop or change speed while
on the slope.

attachments. These can change the stability of
the unit.

Safety Rules & Information

Not for

Reproduction

SERVICE AND MAINTENANCE

To avoid personal injury or property damage, use
extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the
engine running. Allow the engine to cool before
refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where
there is an open flame, spark, or pilot light such
as near a water heater or other appliance.

6. Never fill containers inside a vehicle or on a
truck bed with a plastic bed liner. Always place
containers on the ground away from your vehicle
before filling.

7. Remove gas-powered equipment from the truck
or trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer
with a portable container, rather than from a
gasoline dispenser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing
immediately.

10. Never over-fill the fuel tank. Replace gas cap and
tighten securely.

11. Use extra care in handling gasoline and other
fuels. They are flammable and vapors are
explosive.

12. If fuel is spilled, do not attempt to start the engine
but move the machine away from the area of
spillage and avoid creating any source of ignition
until fuel vapors have dissipated.

13. Replace all fuel tank caps and fuel container caps
securely.

Maintenance and Storage

1. Always observe safe refueling and fuel
handling practices when refueling the unit after
transportation or storage.

2. Always follow the engine manual instructions for
storage preparations before storing the unit for
both short and long term periods.

3. Always follow the engine manual instructions for
proper start-up procedures when returning the unit
to service.

4. Never store the machine or fuel container inside
where there is an open flame, such as in a water
heater. Allow unit to cool before storing.

5. Shut off fuel while storing or transporting. Do not
store fuel near flames or drain indoors.

6. Keep all hardware, especially blade attachment
bolts, tight and keep all parts in good working
condition. Replace all worn or damaged decals.

7. Never tamper with safety devices. Check their
proper operation regularly.

8. Disengage drives, lower implement, set parking

9. Clean grass and debris from cutting units, drives,

brake, stop engine and remove key or disconnect
spark plug wire. Wait for all movement to stop
before adjusting, cleaning or repairing.

mufflers, and engine to prevent fires. Clean up oil
or fuel spillage.

10. Let engine cool before storing and do not store
near flame.

11. Stop and inspect the equipment if you strike an
object. Repair, if necessary, before restarting.

12. Park machine on level ground. Never allow
untrained personnel to service machine.

13. Use jack stands to support components when
required.

14. Carefully release pressure from components with
stored energy.

15. Disconnect battery or remove spark plug wire
before making any repairs. Disconnect the
negative terminal first and the positive last.
Reconnect positive first and negative last.

16. Use care when checking blades. Wrap the
blade(s) or wear gloves, and use caution when
servicing them. Only replace blades. Never
straighten or weld them.

17. Keep hands and feet away from moving parts.
If possible, do not make adjustments with the
engine running.

18. Charge batteries in an open well ventilated area,
away from spark and flames. Unplug charger
before connecting or disconnecting from battery.
Wear protective clothes and use insulated tools.

19. Grass catcher components are subject to wear,
damage, and deterioration, which could expose
moving parts or allow objects to be thrown.
Frequently check components and replace
with manufacturer’s recommended parts, when
necessary.

20. Check brake operation frequently. Adjust and
service as required.

21. Use only factory authorized replacement parts
when making repairs.

22. Always comply with factory specifications on all
settings and adjustments.

23. Only authorized service locations should be
utilized for major service and repair requirements.

24. Never attempt to make major repairs on this unit
unless you have been properly trained. Improper
service procedures can result in hazardous
operation, equipment damage and voiding of
manufacturer’s warranty.

25. Units with hydraulic pumps, hoses, or motors:
WARNING: Hydraulic fluid escaping under
pressure may have sufficient force to penetrate
skin and cause serious injury. If foreign fluid is
injected into the skin it must be surgically removed
within a few hours by a doctor familiar with this
form of injury or gangrene may result. Keep body
and hands away from pin holes or nozzles that
eject hydraulic fluid under high pressure. Use
paper or cardboard, and not hands, to search for
leaks. Make sure all hydraulic fluid connections
are tight and all hydraulic hoses and lines are in
good condition before applying pressure to the
system. If leaks occur, have the unit serviced
immediately by your authorized dealer.

26. WARNING: Stored energy device. Improper
release of springs can result in serious personal
injury. Springs should be removed by an
authorized technician.

7

Operator Safety

Not for

Reproduction

Safety Decals

This unit has been designed and manufactured to provide
you with the safety and reliability you would expect from an
industry leader in outdoor power equipment manufacturing.

Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and effectively,
we have placed several safety labels on the unit to remind
you of this important information while you are operating
your unit.

All DANGER, WARNING, CAUTION and instructional
messages on your mower and mower deck should be
carefully read and obeyed. Personal bodily injury can result
when these instructions are not followed. The information is
for your safety and it is important! The safety decals below
are on your mower and mower deck.

If any of these decals are lost or damaged, replace them at
once. See your local dealer for replacements.

These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.

1

2

3

4

5

*This decal is located on the battery of CE models
only.

1

2

3 , 4

8

4

3 , 4

www.ferrisindustries.com

CE Safety Icons

Not for

Reproduction

Operator Safety

Warning: Read Operator’s Manual

Read and understand the operator’s
manual before using this machine.

Danger: Fire Hazard

Keep the unit free of grass, leaves
and excess oil. Do not add fuel while
engine is hot or running. Stop engine
and allow to cool for at least 3 minutes prior to adding fuel.
Do not add fuel indoors, in an enclosed trailer, garage or
other enclosed areas. Clean up spilled fuel. Do not smoke
while operating this machine.

Danger: Thrown Objects

This machine is capable of thrown
objects and debris. Keep bystanders
away.

Danger: Dismemberment

This mower deck can amputate limbs.
Keep hands and feet away from blades.

Warning: Fire Hazard

Danger: Carbon Monoxide Poisoning

Do not operate the engine in an
unventilated area.

Danger: Machine Rollover

Operating on steep slops can cause
sliding and loss of steering, control
and rollover.

Danger: Dismemberment

This machine can crush and cut. Keep
hands away from belts and pulleys.

Warning: Batteries produce explosive
gases.

Read and understand the Operator’s
Manual before using this machine.

Important: Do not discard a battery in
the trash.

Contact local authorities for disposal
and/or recycling of batteries.

Keep children, open flames and sparks
away from the battery, which could
ignite explosive gases.

Warning: Sulfuric acid can cause
blindness or severe burns

Always wear safety goggles or a face
shield when working on or near a
battery.

9

Operator Safety

Not for

Reproduction

Safety Interlock System

This unit is equipped with safety interlock switches. These
safety systems are present for your safety, do not attempt
to bypass safety switches, and never tamper with safety
devices. Check their operation regularly.

Safety Icons

The alert symbol ( ) is used to identity safety information
about hazards that can result in personal injury. A signal
word (DANGER, WARNING, or CAUTION) is used with the
alert symbol to indicate the likelihood and the potential
severity of the injury. In addition, a hazard icon may be
used to represent the type of hazard. An explanation of
hazard levels and icons are as follows:

Operational SAFETY Checks

Test 1 — Engine should NOT crank if:

• PTO switch is engaged, OR

• Parking brake is not engaged, OR

• Forward speed control lever is not in the NEUTRAL
position.

Test 2 — Engine SHOULD crank if:

• PTO switch is NOT engaged, AND

• Parking brake is engaged, AND

• Forward speed control lever is in the NEUTRAL position.

Test 3 — Engine should SHUT OFF if:

• Operator releases the operator presence handles with
the PTO engaged OR

• Operator releases the operator presence handles with
the parking brake disengaged.

Test 4 — Blade Brake Check
Mower blades and mower drive belt should come to a

complete stop within seven (7) seconds after electric PTO
switch is turned off (or operator releases the operator
presence handles). If mower drive belt does not stop within
seven (7) seconds, see your dealer.

DANGER

This indicates a hazard which, if not avoided, will result in
serious injury or death.

WARNING

This indicates a hazard which, if not avoided, could result
in serious injury or death.

CAUTION

This indicates a hazard which, if not avoided, might result
in serious injury or death.

NOTICE

This message presented without the alert symbol indicates
a situation where the unit or property could be damaged.

North American Safety Icons

Alert Toxic Fumes

Read the

Manual

Open Flame

Hazard

NOTE: Once the engine has stopped, PTO switch must be
turned off, parking brake must be engaged, the forward
speed control lever must be locked in the NEUTRAL
position, and the operator must engage the operator
presence handles in order to start the engine.

WARNING

If the unit does not pass a safety test, do NOT operate
it. See your authorized dealer. Under no circumstance
should you attempt to defeat the purpose of the safety
interlock system.

Fire Hazard

Thrown Objects Hot Surface

10

Kickback

Amputation -

Rotating Parts

Remove

Key Before

Servicing

Amputation -

Hand In Blade

Wear Protective

Gear

www.ferrisindustries.com

Amputation ­Foot In Blade

Pinch Point

Features and Controls

SAMPLE

SAMPLE

Not for

Reproduction

Identification Numbers

SAMPLE

North American
Models

PRODUCT IDENTIFICATION

SAMPLE

XXXX

XXXXXXXXXXXXXXX
MODEL XXXXXXX

SERIAL

XXXXXXXX

NO

0

123456 789012

Briggs & Stratton Power Product Group, LLC
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX

When contacting your authorized dealer for replacement
parts, service, or information you MUST have these
numbers.

min

kW

XXX

kg

XXX

XXX

20xx

Assembled in U.S.A

CE Models

Features and Controls

Identifi cation

Tag

Record your model / serial number and engine serial
numbers on the space provided for easy access. These
numbers can be found in the locations shown.

NOTE: For location of engine identification numbers, refer to
engine owner’s manual.

CE Identification Tag Markings

A. Manufacturer’s Identification Number

B. Product Description

C. Serial Number

D. Manufacturer’s Address

E. CE Compliance Logo

F. Year of Manufacture

G. Maximum Engine Speed in Rotations Per Minute

H. Power Rating in Kilowatts

I. Mass of Unit in Kilograms

J. Sound Power in Decibels*

This unit complies with European Harmonized Lawn Mower Standard EN
836, European Machinery Directive 98/37/EC, and European EMC Directive
89/336/EC

* Tested according to 2000/14/EC

B

A

C

D

XXXXXXXXXXXXXXX
MODEL XXXXXXX

SERIAL

XXXXXXXX

NO

0

123456 789012

Briggs & Stratton Power Product Group, LLC
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX

G

PRODUCT IDENTIFICATION

XXXX

min

kW

XXX

kg

XXX

XXX

20xx

Assembled in U.S.A

F

E

H

I

J

11

Features and Controls

Not for

Reproduction

Control Functions

The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require
the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to
use for various tasks see the OPERATION section.

Transmission Release Levers

The transmission release levers deactivate the transaxle
so that the unit can be pushed by hand. See Pushing The
Unit By Hand for operational information.

Cutting Height Adjustment Handles

The cutting height adjustment handles control the mower
deck cutting height. To raise the mower deck cutting
height crank the cutting height adjustment handles
clockwise. To lower the mower deck cutting height, crank
the cutting height adjustment handles counter-clockwise.
To ensure an even cut, both cutting height adjustment
handles must be adjusted to the same height.

Transmission Oil Fill

Transmission oil is added through the transmission oil
reservoirs. It also serves as extra holding capacity for
oil as the transmissions heat up and the oil expands.
See Check Transmission Oil for oil level check and fill
procedures.

Fuel Tank Cap

To remove the cap turn counter-clockwise.

12

www.ferrisindustries.com

Features and Controls

Not for

Reproduction

Forward Speed Control Lever

Reverse Speed Control Levers

These levers control the ground speed of the mower.

The forward speed control lever controls the forward
ground speed control of both drive wheels.

The left reverse speed control lever controls the steering
and reverse ground speed of the left drive wheel. The
right reverse speed control lever controls the steering and
reverse ground speed of the right drive wheel.

See the Operation section for proper steering instructions.

Engine Kill / Operator Presence Handles

These handles are a major factor in the safety interlock
system of the mower. Both handles are tied together so
depressing one handle depresses both. The operator must
depress the handles in order to deactivate the engine kill
system. Handles must be depressed to disengage the
parking brake and engage the PTO switch.

PTO (Power Take Off) Switch

The PTO switch engages and disengages the mower.
Pull UP on the switch to engage, and push DOWN to
disengage.

Throttle Control

The throttle controls the engine speed. Move the throttle
control forward toward the FAST position to increase
the engine speed and back towards the SLOW position
to decrease the engine speed. Always operate at FULL
throttle.

FAST Speeds up the engine speed.

SLOW Slows down the engine speed.

Parking Brake

Pull the parking brake handle up to engage the parking
brake. Push the parking brake handle down to disengage
the parking brake. To start the unit the parking brake

must be engaged.

DISENGAGE Releases the parking brake.

ENGAGE Locks the parking brake

Neutral Return Pedal

The neutral return pedal provides a hands-free return to
neutral. The pedal is used in conjunction with the reverse
speed control levers to properly stop the machine.

Ignition Switch

The ignition switch starts and stops the engine, it has three
positions:

OFF Stops the engine and shuts off the electrical

system.

RUN Allows the engine to run and powers the

electrical system.

START Cranks the engine for starting

Note: Never leave the ignition switch in the RUN position
with the engine stopped-this drains the battery.

See the Operation section for driving instructions.

Choke

Close the choke for cold starting. Open the choke once the
engine starts. A warm engine may not require choking.
Pull the knob UP to close the choke. Push the knob
DOWN to open the choke.

13

Operation

Not for

Reproduction

Operation

General Operating Safety

Before first time operation:

• Be sure to read all information in the Safety and
Operation sections before attempting to operate this
unit.

• Become familiar with all of the controls and how to stop
the unit.

• Drive in an open area without mowing to become
accustomed to the unit.

Checks Before Starting

• Check that crankcase is filled to full mark on the engine
oil dipstick (B, Figure 1). See the engine Operator’s
Manual for instructions and oil recommendations.

• Fill the fuel tank (A) with fresh fuel. Refer to engine
manual for fuel recommendations.

• Make sure all nuts, bolts, screws and pins are in place
and tight.

• Check the tire pressures. See Check Tire Pressures.

• Check the hydraulic oil tank (C) and make sure that the
oil level is up to the FULL COLD mark.

• Adjust the height of the mower deck to the desired
position. See Mowing Height Adjustment.

A

WARNING

Operating on steep slopes can be dangerous.

• Select slow ground speed before driving onto a slope.

• Mow across the face of slopes, not up and down, use
caution when changing directions and DO NOT START
OR STOP ON A SLOPE.

Starting the Engine

1. Engage the parking brake and make sure that the
PTO switch is disengaged and the forward speed control
lever is in the NEUTRAL position.

2. NOTE: A warm engine may not require choking.

Set the engine throttle control to FULL throttle position.

Then fully close the choke by pulling the knob OUT fully.

WARNING

If you do not understand how a specific control functions,
or have not yet thoroughly read the Features and Controls
section, do so now.

Do NOT attempt to operate the unit without first becoming
familiar with the location and function of ALL controls.

3. Insert the key into the ignition switch and turn it to the
START position.

4. After the engine starts, gradually open the choke (push
knob down fully). Reduce to half throttle speed and
allow to warm up.

Warm up the engine by running it for at least a minute
before engaging the PTO switch or driving the unit.

B

C

Figure 1. Pre-start Checks
A. Fuel Tank Filler Neck

B. Engine Oil Dipstick
C. Hydraulic Oil Fill

WARNING

• Before leaving the operator’s position for any reason,
engage the parking brake, disengage the PTO, stop the
engine and remove the key.

• To reduce fire hazard, keep the engine, unit and mower
free of grass, leaves and excess grease. Do NOT stop
or park tractor over dry leaves, grass or combustible
materials.

• Gasoline is highly flammable and must be handled with
care. Never fill the tank when the engine is still hot from
recent operation. Do NOT allow open flame, smoking or
matches in the area. Avoid over-filling and wipe up any
spills.

5. After warming the engine, ALWAYS operate the unit at
FULL THROTTLE when mowing.

In the event of an emergency the engine can be stopped by
simply turning the ignition switch to STOP. Use this method
only in emergency situations. For normal engine shut down
follow the procedure given in Stopping the Mower.

Stopping the Mower

1. Gently squeeze both reverse speed control levers evenly
to stop the unit.

2. Once the unit is stopped, firmly depress the neutral
return pedal to place the transmission in neutral.

3. Disengage the PTO by pushing down on the PTO switch.

3. Engage the parking brake by pulling the handle up until it
locks into position.

4. Move the throttle control to mid-throttle position and
turn the ignition key to OFF. Remove the key.

14

www.ferrisindustries.com

Check Tire Pressures

Not for

Reproduction

Tire pressure should be checked periodically, and
maintained at the levels shown in the chart. Note that these
pressures may differ slightly from the “Max Inflation”
stamped on the side-wall of the tires. The pressures shown
in Specifications provide proper traction, improve cut
quality, and extend tire life.

Pushing the Mower By Hand

NOTICE

Towing the units will cause hydraulic pump and wheel
motor damage. Do NOT use another vehicle to push or
pull this unit.

1. Disengage the PTO, engage the parking brake, turn the
ignition OFF, and remove the key.

2. Locate the transmission release levers (A, Figure 3) by
the rear wheels of the unit.

3. To disengage the pumps (free-wheel position), pull both
transmission release levers back and out so they lock in
the disengaged (free-wheel) position.

4. Disengage the parking brake.

The unit can now be pushed by hand.

5. After moving the unit, re-engage the pumps (drive
position) by pulling the transmission release levers
rearward and inward to release them from the
disengaged position and then allow them to move to the
engaged (drive) position.

Operation

Figure 2. Checking Tire Pressure

A

B

C

Figure 3. Transmission Release Levers (LH Shown)
A. Transmission Release Levers
B. Engaged Position (Drive Position)
C. Disengaged Position (Free-Wheel Position)

15

Operation

Not for

Reproduction

Cutting Height Adjustment

The cutting height can be adjusted within two different
ranges. The lower cutting range is adjustable between
1-1/2” (3,8 cm) and 2-3/4” (6,9 cm). The upper cutting
range is adjustable between 2-3/4” (6,9 cm) and 4-1/2”
(11,5 cm).

Before adjusting the cutting height, you must first determine
the average cutting height. Depending on the range you
plan to use, it may be necessary to adjust which pulley the
deck drive belt runs in.

To Adjust the Cutting Range:

See your authorized dealer.

To Adjust the Cutting Height:

The cutting range must be adjusted to the correct range
before the cutting height can be adjusted. The cutting
height indicators will help you identify the cutting height.

1. Pull the cutting height adjustment handle (A, Figure 4)
up and out of the handle lock position (B) and crank the
handle clockwise to raise the deck to the desired cutting
height. Crank the handle counter-clockwise to lower
the deck to the desired cutting height. After the desired
cutting heights are achieved position the cutting height
adjustment handles into the handle lock position.

2. Repeat the process for the other side of the machine.

NOTE: Both sides of the cutter deck must be adjusted to the
same height to insure a proper cut.

A

B

C

Figure 4. Cutting Height Adjustment
A. Cutter Height Adjustment Handle
B. Handle Lock Position
C. Cutting Height Indicator

16

www.ferrisindustries.com

Driving The Mower

Not for

Reproduction

Before attempting to drive the mower make sure you have
read the Features and Controls section and understand the
location and function of the controls.

The hydrostatic transmission has an infinite number of
speeds between full speed forward and reverse, with the
faster speeds being achieved by moving the forward speed
control lever and reverse speed control levers farthest in the
direction of travel.

For normal use, the throttle should be kept fully open and
the ground speed of the machine determined by the forward
speed control lever. When transporting the machine or when
loading or unloading from a truck or trailer, partial throttle
should be used to slow the reaction time of the controls and
reduce noise.

Practice maneuvering the machine at a slow engine speed on
level ground with the PTO switch in the “OFF” position until
you are familiar with the controls.

To Move Forward and Set Forward Speed

1. Disengage the parking brake.

2. Gently move the forward speed control lever (A, Figure

5) forward until desired speed is achieved.

To Move Backward

1. Disengage the parking brake.

2. Gently squeeze both reverse speed control levers (B)

evenly, until desired speed is achieved.

Operation

To Slow or Stop Machine

1. Gently squeeze both reverse speed control levers evenly
to slow the machine.

2. Continuing to squeeze the reverse speed control levers
will stop the machine.

3. Once the machine is stopped, firmly depress the neutral
return pedal to place the transmissions in neutral.

4. Engage the parking brake.

NOTE: Continuing to squeeze the reverse speed control
levers after the machine is stopped, will cause the machine
to move in reverse.

Turning the Machine

Note: Always reduce speed in a turn.

Turning Left:

Gently squeeze the left hand reverse speed control lever (C).
A sharp or gentle turn is determined by the amount of force
applied to the steering control lever.

Turning Right:

Gently squeeze the right hand reverse speed control lever
(D). A sharp or gentle turn is determined by the amount of
force applied to the steering control lever.

A

Figure 5. Driving the Mower
A. Forward Speed Control Lever
B. Reverse Speed Control Levers
C. Left Hand Speed Control Lever
D. Right Hand Speed Control Lever

B

C

D

17

Operation

Not for

Reproduction

Mowing

Before mowing, set the cutting height as described in
Cutting Height Adjustment.

1. Engage the parking brake. Make sure the PTO switch is
disengaged and the forward speed control lever is in the
NEUTRAL position

2. Start the engine (see Starting The Engine).

3. Set the throttle to FULL.

4. Engage the PTO by pulling up on the PTO switch.

5. Begin mowing. See Mowing Recommendations for tips
on mowing patterns, lawn care, and trouble shooting
information.

6. When finished, shut off the PTO by pushing the PTO
switch down completely.

7. Stop the engine (see Stopping The Engine).

Mowing Recommendations

Several factors can affect how well your machine cuts grass,
Following proper mowing recommendations can improve
the performance and life of your machine.

Height of Grass

Often cutting height is a matter of personal preference.
Typically, you should mow the grass when it is between
three and five inches high. The proper cutting height
range for a specific lawn will depend upon several factors,
including the type of grass, the amount of rainfall, the
prevailing temperature, and the lawn’s overall condition.

• Cutting the grass too short causes weak, thin grass
plants, which are easily damaged by dry periods and
pests.

• Letting grass grow a bit longer—especially when it is
hot and dry—reduces heat build-up, preserves needed
moisture and protects the grass from heat damage and
other problems. However, allowing grass to grow too
high can cause thin turf and additional problems.

• Cutting off too much at one time shocks the plant’s
growth system and weakens the grass plants. A good

rule of thumb is the 1/3 rule: to cut no more than one
third of the grass height, and never more than 1 inch
at a time.

• The amount of grass you are able to cut in one pass
is also effected by the type of mowing system you are
using (for example, broadcasting with side discharge
decks can process a much larger volume of grass than
mulching does).

Proper Cutting Height

Tall Grass Requires Incremental Cutting

For extremely tall grass, set the cutting height at maximum
for the first pass, and then reset it to the desired height and
mow a second or third time.

Don’t cover the grass surface with a heavy layer of
clippings. Consider using a grass collection system and
starting a compost pile.

Cut Here On
First Pass

Incremental Cutting

Cut Here
On Second
Pass

18

www.ferrisindustries.com

When and How Often to Mow

Not for

Reproduction

The time of day and condition of the grass greatly affect the
results you’ll get when mowing. For the best results, follow
these guidelines:

1. Mow when the grass is between three and five inches
high.

2. Mow with sharp blades. Short clippings of grass one
inch or shorter decompose more quickly than longer
blades. Sharp mower blades cut grass cleanly and
efficiently, preventing frayed edges which harm the
grass.

3. Mow at time of day when the grass is cool and dry.
Late afternoon or early evening often provide these ideal
mowing conditions.

4. Avoid mowing after rain or even heavy dew, and never
mulch when the grass is wet (moist grass does not
mulch well, and clumps beneath the mower deck).

Mowing Patterns

Always start mowing on a smooth, level area.

The size and type of area to be mowed will determine the
best mowing pattern to use. Obstructions such as trees,
fences and buildings, and conditions such as slopes and
grades must also be considered.

1. Cut long straight strips overlapping slightly.

2. Where possible, change patterns occasionally to
eliminate matting, graining or a corrugated appearance.

3. For a truly professional cut, mow across the lawn in one
direction, then recut the lawn by mowing perpendicular
to the previous cut.

Note: Always operate the engine at full throttle when
mowing.

If you hear the engine slowing down, you are mowing
too fast—using a slower ground speed will improve the
cutting efficiency of the blades and prevents many common
cutting problems. Use an appropriate ground speed for the
thickness and height of the grass you are cutting (3rd gear
or slower for manual gear models). If you hear the engine
slowing down you are mowing too fast, use a slower ground
speed.

Operation

Where possible, make one or two passes around the outside
of the area discharging the grass INTO the lawn to keep the
cut grass off fences and walks.

The remainder of the mowing should be done in the
opposite direction so that the clippings are dispersed OUT
onto the area of lawn previously cut.

Mowing Methods

Proper Broadcast Mowing

Broadcasting, or side-discharging, disperses fine clippings
evenly over the entire lawn. Many golf courses use this
method. Your mower has a deep dish deck to allow freer
circulation of clippings so they are broadcast evenly over the
lawn.

Engine Speed & Ground Speed for Broadcasting

Always operate the engine at full throttle when mowing. If
you hear the engine slowing down, you are mowing too
fast—using a slower ground speed will improve the cutting
efficiency of the blades and prevents many common cutting
problems.

ALWAYS use an appropriate ground speed for the thickness
and height of the grass you are cutting (3rd gear or slower
for manual gear models). If you hear the engine slowing
down you are mowing too fast, use a slower ground speed.

How Much Grass to Cut Off When Broadcasting

Mow when the grass is 3-5 inches long. Do not cut the
grass shorter than 2 to 2-1/2 inches. Do not cut off more
that 1 inch of grass in a single pass

19

Operation

Not for

Reproduction

Proper Mulching

Mulching consists of a mower deck which cuts and recuts
clippings into tiny particles and which then blows them
down INTO the lawn. These tiny particles decompose rapidly
into by-products your lawn can use. UNDER PROPER
CONDITIONS, your mulching mower will virtually eliminate
noticeable clippings on the lawn surface.

NOTE: When mulching under heavy cutting conditions, a
rumbling sound may be present and is normal.

Mulching Requires EXCELLENT Mowing Conditions

Mulching mowers cannot function properly if the grass is
wet, or if the grass is simply to high to cut. Even more than
normal mowing, mulching requires that the grass be dry and
the appropriate amount is cut.

Do not use the mower as a mulching mower during the first
two or three mowings in the spring. The long grass blades,
quick growth, and often wetter conditions are more suitable
for broadcasting (side-discharging) or grass bagging
operation.

Engine Speed & Ground Speed for Mulching

Use full engine throttle matched with a slow ground speed
so that clippings will be finely cut. Ground speed while
mulching should be HALF of the speed that would be
used when broadcasting (side discharging) under similar
conditions. Since mulching requires more horsepower
than broadcasting, using a slower ground speed is vitally
important for proper mulching operation.

How Much Grass to Mulch

The best mulching action typically results from cutting only
the top 1/2 inch to 3/4 inch of grass blade. This provides
short clippings which decompose properly (much more
quickly than longer clippings). The ideal cutting height will
vary with climate, time of year, and quality of your lawn. We
recommend that you experiment with both the cutting height
and ground speed until you achieve the best cut. Start with
a high cutting height and using progressively lower settings
until you find a cutting height that is matched to your
mowing conditions and preferences.

Mulching Action

20

www.ferrisindustries.com

Specifications

Not for

Reproduction

NOTE: Specifications are correct at time of printing and are subject to change without notice.

Specifi cations

ENGINE

For models 5900749 & 5900758

15 Gross HP† Kawasaki

Make Kawasaki
Model FH430V
Displacement 431 cc (26.3 cu. in.)
Oil Capacity 1.9 US qt. (1.8 L) w/ filter

For models 5900987 & 5900988

16 Gross HP† Kawasaki

Make Kawasaki
Model FS481V
Displacement 603 cc (36.8 cu. in.)
Oil Capacity 1.8 US qt. (1.7 L) w/ filter

For models 5900542 & 5900541

15 Gross HP† Kawasaki

Make Kawasaki
Model FS481V
Displacement 603 cc (36.8 cu. in.)
Oil Capacity 1.8 US qt. (1.7 L) w/ filter

†Power Ratings: All power levels are stated gross horsepower per
SAE J2723 as rated by Kawasaki and tested per the SAE J1995
test standard. The gross power curves and more information can be
viewed at www.kawasaki-criticalpower.com.

TRANSMISSIONS

Models 5900749 & 5900758:
Hydro-Gear ZH-KMBB-3A5A-1LLX (LH)
Hydro-Gear ZH-GMBB-3A5A-1LLX (RH)
Models 5900987, 5900988, 5900542 & 5900541:
Hydro-Gear ZJ-KMFE-3B5B-1RLX (LH)
Hydro-Gear ZJ-GMFE-3B5B-1RLX (RH)

Type ZT2800
Hydraulic Fluid SAE 20W-50 motor oil
Speeds @ 3400 rpm Forward: 0-6 MPH (0-9.66 km/h)

Reverse: 0-3 MPH (0-4.83 km/h)

DIMENSIONS

Models 5900749 & 5900758:
Overall Length 76” (193 cm)
Overall Width 37” (93,9 cm)
Height 42” (106,5 cm)
Weight (apx.) 480 lbs (218 kg)
Models 5900987, 5900988, 5900542 & 5900541:
Overall Length 80” (203 cm)
Overall Width 37” (93,9 cm)
Height 42” (106,5 cm)
Weight (apx.) 590 lbs (268 kg)

CHASSIS

Fuel Tank

Rear Wheels

Models 5900749 &
5900758

Models 5900987, 5900988,
5900542 & 5900541

Front Wheels

Models 5900749 &
5900758

Models 5900987, 5900988,
5900542 & 5900541

Capacity: 5.5 gallons (20.82 L)

Tire Size: 18 x 6.50 - 8;
Inflation Pressure: 15 psi (1,03 bar)

Tire Size: 20 x 7.00 - 10;
Inflation Pressure: 15 psi (1,03 bar)

Tire Size: 9 x 3.50 - 4;
Inflation Pressure: 25 psi (1,72 bar)

Tire Size: 11 x 4.00 - 5;
Inflation Pressure: N/A

21

FOLD ALONG APPROPRIATE DOTTED LINE

Not for

Reproduction

1

3

COMPARE THE ANGLE

OF THE FOLD TO THE

ANGLE OF THE SLOPE

INSTRUCTIONS

1. Fold this page along

the dotted line indicated

above.

2. Align the left edge of this

guide with a vertical tree,

a power line pole, a fence

post, or any vertical

structure.

3. Compare the angle of the

fold with the angle of the

hill.

SLOPE INDENTIFICATION GUIDE

22

THIS IS A 15 DEGREE SLOPE

THIS IS A 10 DEGREE SLOPE

(TREE, POLE, FENCE POST, BUILDING, ETC)

ALIGN THIS EDGE WITH A VERTICAL SURFACE

2

www.ferrisindustries.com

Notes

Not for

Reproduction

Not for

Reproduction

Ferris Industries - a division of Briggs & Stratton Power Products Group, LLC.

Not for

Reproduction

Owner’s Limited Warranty Information

(Effective 04/28/2004)

Thank you for purchasing Ferris commercial mowing equipment. Please take a few minutes to read this limited warranty information. It contains all
the information you will need to have your Ferris mower repaired in the unlikely event that a breakdown covered by this limited warranty should occur.

Owner’s Responsibilities - As a condition to our obligations under this limited warranty, you shall have read the operator’s manual and you shall
have completed and submitted to Ferris, within 20 days from the date of purchase, the Ferris Product Registration. You must properly service and
maintain your Ferris product as described in the operator’s manual. Such routine maintenance, whether performed by a dealer or by you, is at your
expense. The Ferris equipment, including any defective part covered by this limited warranty, must be returned to an authorized Ferris dealer within
the warranty period for warranty service. This limited warranty extends only to equipment operated under normal conditions and in accordance with
Ferris’ instructions.

Warranty Start Date - The limited warranty coverage begins on the day you buy your new Ferris commercial mowing equipment. An authorized Ferris
dealer will assist you in filling out a Ferris Product Registration with specific information for the model you purchase and your personal information,
which must be returned to Ferris.

Limited Warranty - The limited warranty, set forth below, is a written guarantee by Ferris, during the warranty period, to repair or replace parts which
have a substantial defect in materials or workmanship. The warranty is “limited” because it is for a specified period of time, applies to the original pur­chaser only, and is subject to other restrictions.

FERRIS LIMITED WARRANTY

Ferris Industries (Ferris) warrants, in accordance with the provisions below, to the original purchaser only, for the periods described below that the
commercial mower shall be free from substantial defects in material or workmanship under normal use and service. If you wish to file a claim under
this limited warranty, you must provide prompt notice of your claim to an authorized Ferris dealer during the warranty period. Ferris’ obligation under
this limited warranty is, at Ferris’ option, to repair or replace any part or parts of the mower, which, in the judgment of Ferris, are found to be defective
and covered by this limited warranty. An authorized Ferris dealer will repair or replace the defective part or parts, at the dealer’s place of business,
at no charge for the labor or parts. This limited warranty applies only to mowers sold in the United States and Canada and is subject to the following
limitations.

Covered Parts Warranty Period

All Mowers 2-years (24 months) from date of retail purchase by the original
purchaser for parts & labor (90 days for rental mowers)
(Except as noted below*)

*Belts, Tires, Brake Pads 90 days from date of retail purchase by the original purchaser
And Hoses, Battery, Blades

*Attachments 1 year from date of retail purchase by the original purchaser

*Engine If the engine manufacturer provides any warranty on the mower’s engine, Ferris will assign that warranty to
the original purchaser of the mower if such assignment is reasonably practicable. Please refer to the engine
manufacturer’s warranty statement, if any, that is included in the owner’s packet. We are not authorized to
handle warranty adjustments or repairs on engines. Ferris offers NO WARRANTY on mower engines. Ferris
does not guarantee or represent that any engine manufacturer will comply with the terms of its warranty.

Items and Conditions Not Covered

This warranty does not cover, and Ferris makes NO WARRANTY regarding, the following:

• Mowers or their parts if a complete and accurate Ferris Product Registration has not been received by Ferris.

• Loss or damage to person or property other than that expressly covered by the terms of this limited warranty.

• Pickup and delivery charges and risk of loss or damage in transit to and from any authorized Ferris dealer.

• Any damage or deterioration due to normal use, wear and tear, or environmental or natural elements, or exposure.

• Cost of regular maintenance service or parts, such as but not limited to, filters, fuel, lubricants, tune-up parts, and adjustments.

• Claims arising due to failure to follow Ferris’ written instructions, or improper storage or maintenance.

• Any repairs necessary due to use of parts, accessories or supplies, including gasoline, oil or lubricants, incompatible with the mowing equipment,
or other than as recommended in the operator’s manual or other written operational instructions provided by Ferris.

• Use of non-Ferris approved parts or accessories.

• Any overtime or other extraordinary repair charges or charges relating to repairs or replacements.

• Rental of like or similar replacement equipment during the period of any warranty, repair or replacement work.

• Loss of revenue, time or use of the mowing equipment.

• Travel, telephone or other communication charges.

• Damage from continued use of defective mowing equipment.

• Freight charges on replacement parts.

• Any mowing equipment or part which, in the judgment of Ferris, has been altered or tampered with in any way or has been subjected to misuse,
abuse, abnormal usage, unauthorized repair, neglect or accident, damage in transit, or has had the serial numbers altered, effaced or removed.

• Any equipment, part or item not mentioned under “Covered Parts,” above.

General Conditions

Ferris is continually striving to improve its products, and therefore reserves the right to make improvements or changes without incurring any obliga­tion to make changes or additions to products sold previously. Any oral or written description of Ferris products is for the sole purpose of identifying
the products and shall not be construed as an express warranty. No warranty claim shall give rise to a right for the purchaser to cancel or rescind any
sale. No person is authorized to make any warranty or assume for Ferris any liability not strictly in accordance with this limited warranty. Any assis­tance Ferris provides to or procures for the purchaser outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of
the terms, limitations or exclusions of this limited warranty, nor will such assistance extend or revive the limited warranty. Ferris will not reimburse the
purchaser for any expenses incurred by the purchaser in repairing, correcting or replacing any defective products except for those incurred with Ferris’
prior written permission and in accordance with this limited warranty.

Ferris’ sole and exclusive liability with respect to this limited warranty, and the purchaser’s exclusive remedy, shall be repair or replacement as set
forth herein. All warranty work must be performed by an authorized Ferris dealer using only Ferris approved replacement parts. FERRIS SHALL

HAVE NO LIABILITY FOR ANY OTHER COST, LOSS OR DAMAGE, INCLUDING BUT NOT LIMITED TO, ANY INCIDENTAL, COMPENSATORY,
INDIRECT, PUNITIVE, SPECIAL OR CONSEQUENTIAL LOSS OR DAMAGE. FERRIS’ AGGREGATE LIABILITY WITH RESPECT TO A
DEFECTIVE PRODUCT OR PART SHALL BE LIMITED TO AN AMOUNT EQUAL TO THE MONIES PAID BY THE PURCHASER FOR THAT
DEFECTIVE PRODUCT OR PART. THIS LIMITED WARRANTY, AND FERRIS’ OBLIGATIONS HEREUNDER, ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTY OF MERCHANTABILITY
AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. FERRIS SHALL NOT BE LIABLE TO THE PURCHASER,
OR TO ANYONE CLAIMING UNDER THE PURCHASER, FOR ANY OTHER OBLIGATIONS OR LIABILITIES, INCLUDING, BUT NOT LIMITED
TO, OBLIGATIONS OR LIABILITIES ARISING OUT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY
THEORY OF STRICT LIABILITY, WITH RESPECT TO FERRIS PRODUCTS OR FERRIS’ ACTS OR OMISSIONS OR OTHERWISE.

It is the express wish of the parties that this agreement and any related documents be drafted in English. Il est la volonté expresse des parties que
cette convention et tous les documents s’y rattachent soient rédigés en anglais.

OPERATOR’S

Not for

Reproduction

MANUAL

CCW36 Series

Walk-Behind Mowers

Briggs & Stratton Power Products Group, LLC

5375 North Main Street
Munnsville, NY 13409
800-933-6175
www.ferrisindustries.com