Fenner QD:E Installation And Operating Instructions Manual

Installation and Operating Instructions

Fenner QDE User Guide 9/5/08 9:23 AM Page 1

Installation & Operating Instructions

ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı

Page 3

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

CONTENTS

Page 2

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

1. I

NTRODUCTION 4

1.1. Important safety information 4

1.2. Electromagnetic Compatibility (EMC) 4

2. GENERAL INFORMATION AND RATINGS 5

2.1. Identifying the drive by model number 5

2.2. Drive model numbers 5

3. MECHANICAL INSTALLATION 6

3.1. General 6

3.2. Mechanical dimensions and mounting 6

3.3. Enclosure mounting 6

4. POWER WIRING 7

4.1. Grounding the Drive 7

4.1.1. Grounding Guidelines 7

4.2. Wiring Precautions 7

4.3. Connection Diagram 8

4.4. Drive and motor connections 8

4.5. Motor Terminal Box Connections 8

5. CONTROL WIRING 9

5.1. Control terminal connections 9

5.2. RJ45 Data Connection 9

6. OPERATION 9

6.1. Managing the keypad 9

6.1.1. Changing Parameters 10

6.1.2. Reset Factory Default Settings 10

6.2. Terminal Control 10

6.3. Keypad Control 10

7. PARAMETERS 11

7.1. Standard parameters 11

7.2. Extended parameters 12

7.2.1. Parameter group zero access and navigation 14

8. ANALOG AND DIGITAL INPUT CONFIGURATIONS 15

8.1. Terminal mode (P-12 =0) 15

8.2. Keypad mode (P-12 = 1 or 2) 16

8.3. MODBUS control mode (P12 = 3 or 4) 17

8.4. User PI control mode (P-12 = 5 or 6) 17

9. TROUBLESHOOTING 18

9.1. Fault messages 18

10.TECHNICAL DATA 18

10.1. Environmental Data 18

10.2. Rating tables 19

10.3. Maximum supply ratings for UL compliance: 19

Fenner QD:E Easy Start Up Guide 20

Declaration of Conformity:

ERIKS Industrial Services Ltd hereby states that the Fenner QD:E Series product range is CE marked for the low voltage directive and conforms to the following harmonised European directives:

EN 61800-5-1: 2003 Adjustable speed electrical power

drive systems. Safety requirements. Electrical, thermal and energy.

EN 61800-3 2nd Adjustable speed electrical Ed: 2004 power drive systems. EMC

requirements and specific test methods

EN 55011: 2007 Limits and Methods of measurement

of radio disturbance characteristics of industrial, scientific and medical (ISM) radio-frequency equipment (EMC)

Company Information

Address: ERIKS Industrial Services Ltd

Amber Way Halesowen West Midlands B62 8WG

Email: sales@ftpgroup.com Website: www.ftpgroup.com

All rights reserved. No part of this User Guide may be reproduced or transmitted in any form or by any means, electrical or mechanical including photocopying, recording or by any information storage or retrieval system without permission in writing from the publisher.

The manufacturer accepts no liability for any consequences resulting from inappropriate, negligent or incorrect installation, or adjustment of the optional operating parameters of the drive or from mismatching of the drive to the motor.

The contents of this User Guide are believed to be correct at the time of printing. In the interest of a commitment to a policy of continuous improvement, the manufacturer reserves the right to change the specification of the product or its performance or the contents of the User Guide without notice.

All Fenner QD Series products carry a 2-year warranty, valid from the date of manufacture. This date is clearly visible on the product rating label.

This User Guide is for use with V1.02 Software. User Guide Issue 1.01

NOTE

ERIKS reserves the right to modify the characteristics of its products at any time in order to incorporate technological developments. The information contained in this document may therefore be changed without notice.

Fenner QDE User Guide 9/5/08 9:23 AM Page 3

Installation & Operating Instructions

Page 5

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 4

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

1. INTRODUCTION

1.1. IMPORTANT SAFETY INFORMATION

This variable speed drive product (Fenner QD Series) is intended for professional incorporation into complete equipment or systems. If installed incorrectly it may present a safety hazard. The Fenner drive uses high voltages and currents, carries a high level of stored electrical energy, and is used to control mechanical plant that may cause injury. Close attention is required to system design and electrical installation to avoid hazards in either normal operation or in the event of equipment malfunction. System design, installation, commissioning and maintenance must be carried out only by personnel who have the necessary training and experience. They must carefully read this safety information and the instructions in this Guide and follow all information regarding transport, storage, installation and use of the Fenner QD Series, including the specified environmental limitations.

Please read the IMPORTANT SAFETY INFORMATION below, and all Warning and Caution information elsewhere.

Indicates a potentially hazardous situation which, if not avoided, could result in injury or death.

Indicates a potentially hazardous situation which, if not avoided, could result in damage to property.

Safety of machinery, and safetycritical applications

The level of integrity offered by the Optidrive control functions – for example stop/start, forward/reverse and maximum speed, is not sufficient for use in safety-critical applications without independent channels of protection. All applications where malfunction could cause injury or loss of life must be subject to a risk assessment and further protection provided where needed. Within the European Union, all machinery in which this product is used must comply with Directive 89/392/EEC, Safety of Machinery. In particular, the electrical equipment should comply with EN60204-1.

• Fenner drives should be installed only by qualified electrical persons and in accordance with local and national regulations and codes of practice. The Fenner drives has an Ingress Protection rating of IP20. For higher IP ratings, use a suitable enclosure.

• Electric shock hazard! Disconnect and ISOLATE the Fenner drives before attempting any work on it. High voltages are present at the terminals and within the drive for up to 10 minutes after disconnection of the electrical supply.

• Where supply to the drive is through a plug and socket connector, do not disconnect until 10 minutes have elapsed after turning off the supply

• Ensure correct earthing connections. The earth cable must be sufficient to carry the maximum supply fault current which normally will be limited by the fuses or MCB

• The STOP function does not remove potentially lethal high voltages. ISOLATE the drive and wait 10 minutes before starting any work on it

• Parameter P-01 can be set to operate the motor at up to 60,000 rpm, hence use this parameter with care.

• If it is desired to operate the drive at any frequency/speed above the rated speed (P-09/ P-10) of the motor, consult the manufacturers of the motor and the driven machine about suitability for overspeed operation.

• The fan (if fitted) inside of the Fenner drive starts automatically when the heatsink temperature reaches approximately 45ºC.

• Carefully inspect the Fenner drive before installation to ensure it is undamaged

• Indoor Use Only.

• Flammable material should not be placed close to the drive

• The entry of conductive or flammable foreign bodies should be prevented

• Relative humidity must be less than 95% (noncondensing).

• Ensure that the supply voltage, frequency and no. of phases (1 or 3 phase) correspond to the rating of the Fenner drive as delivered.

• An isolator should be installed between the power supply and the drive.

• Never connect the mains power supply to the Output terminals U, V, W.

• Suitably rated fuses or MCB should be fitted in the mains supply to the drive

• Do not install any type of automatic switchgear between the drive and the motor

• Wherever control cabling is close to power cabling, maintain a minimum separation of 100 mm and arrange crossings at 90 degrees

• Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit protection must be provided in accordance with the National Electrical Code and any additional local codes

1.2. ELECTROMAGNETIC COMPATIBILITY (EMC)

Fenner drives is designed to high standards of EMC and is fitted with an internal EMC filter as standard. This EMC filter is designed to reduce the conducted emissions back into the supply via the power cables for compliance with harmonised European standards. It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated complies with the EMC legislation of the country of use. Within the European Union, equipment into which this product is incorporated must comply with 89/336/EEC, EMC.

For use on domestic supplies, screened motor cable must be used with the screen terminated to earth on both motor and drive sides. The installation must be carried out by qualified installation engineers, observing good wiring practice such as power and signal cable segregation and correct screening techniques to minimise emissions. When installed in this way, the Fenner drive with built-in filter has emission levels lower than those defined in EN61800-3 category C2 for 1

environments (domestic) for screened cable lengths of up to 5m.

For cable lengths above 5m, the emission levels may exceed those defined by EN61800-3 cat C2. In this case, further mitigation methods (such as fitting an external filter - QFilter) must be employed if the emissions limits for domestic supplies are to be upheld.

When used on industrial supplies, or 2

environments, the installation must be carried out by qualified installation engineers, observing good wiring practice such as power and signal cable segregation and correct screening techniques to minimise emissions. The emissions limits defined by EN61800-3 cat C3 (2

environment) are upheld for screened cable lengths of up to 25m. The cable screen should be connected to earth on both the drive and motor sides.

2. GENERAL INFORMATION AND R

ATINGS

This chapter contains information about the Fenner QD:E including how to identify the drive

2.1. IDENTIFYING THE DRIVE BY MODEL

NUMBER

Each drive can be identified by its model number, as shown in Figure 1 Drive Model Number Format. The model number is on the shipping label and the drive nameplate. The model number includes the drive and any options. Drive model numbers for the Fenner QD:E drives are provided in 10.2 Rating tables.

200-240V ±10% - 1 Phase Input

kW Model Number Output Current Frame

With Filter

kW HP

(A) Size

572B20P4 0.37 0.5 2.3 1

572B20P7 0.75 1 4.3 1

572B21P5 1.5 2 7 1

572B21P5E 1.5 2 7 2

572B22P2 2.2 3 10.5 2

FIGURE 1 DRIVE MODEL NUMBER FORMAT

2.2. D

RIVE MODEL NUMBERS

Inverter

Series

Enclosure

2= IP20 5= IP55

Type B= QD:E Basic drive V= QD:CT Plus Vector drive H= QD:VT HVAC drive

Supply Voltage 2= 220-240V 1~ 3= 220-240V 3~ 4= 380-440V 3~

Rated power code

Special

Features

57 2 B 2 OP4 N

200-240V ±10% - 3 Phase Input

kW Model Number Output Current Frame

With Filter

kW HP

(A) Size

0.37 0.5 2.3 1

0.75 1 4.3 1

1.5 2 7 1

572B31PE 1.5 2 7 2

572B32PE 2.2 3 10.5 2

572B34PO 4.0 5 8 3

380-480V ±10% - 3 Phase Input

kW Model Number Output Current Frame

With Filter

kW HP

(A) Size

572B40P7 0.75 1 2.2 1

572B41P5 1.5 2 4.1 1

572B41PE 1.5 2 4.1 2

572B42P2 2.2 3 5.8 2

572B44P0 4 5 9.5 2

572B45P5 5.5 7.5 14 3

572B47P5 7.5 10 18 3

572B4011 11 15 24 3

Fenner QDE User Guide 9/5/08 9:23 AM Page 5

Installation & Operating Instructions

Page 7

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 6

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

3. MECHANICAL INSTALLATION

3.1. GENERAL

• Store the Fenner QD:E drive in its box until required. Storage should be clean and dry and within the temperature range –40°C to +60°C

• Install the Fenner drive on a flat, vertical, flame-resistant, vibration-free mounting within a suitable enclosure, according to EN60529 if specific Ingress Protection ratings are required

• The drive must be installed in a pollution degree 1 or 2 environment

• Sizes 1 & 2 are DIN rail mountable, Size 3 is not DIN rail mountable.

• Ensure that all terminals are tightened to the appropriate torque setting

3.2. MECHANICAL DIMENSIONS AND MOUNTING

Drive

A B C D E F G H I J

Size

mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in

1 173 6.81 160 6.30 109 4.29 162 6.38 5.0 0.20 123 4.84 82 3.23 50 1.97 5.5 0.22 10 0.39

2 221 8.70 207 8.15 137 5.39 209 8.23 5.3 0.21 150 5.91 109 4.29 63 2.48 5.5 0.22 10 0.39

3 261 10.28 246 9.69 - - 247 9.72 6.0 0.24 175 6.89 131 5.16 80 3.15 5.5 0.22 10 0.39

Control Terminal Torque Settings of 0.5 Nm (4.5 lb-in) Power Terminal Torque Settings of 1 Nm (9 lb-in)

3.3. ENCLOSURE MOUNTING

For applications that require a higher IP rating than the IP20 offered by the standard drive, the drive must be mounted in a metallic enclosure. The following guidelines should be observed for these applications:

• Enclosures should be made from a thermally conductive material.

• When vented enclosures are used, there should be venting above the drive and below the drive to ensure good air circulation. Air should be drawn in below the drive and expelled above the drive.

• If the external environment contains contamination particles (e.g. dust), a suitable particle filter should be fitted to the vents and forced ventilation implemented. The filter must be serviced / cleaned appropriately.

• High moisture, salt or chemical content environments should use a suitably sealed (non-vented) enclosure.

Drive X Y Z Recommended

Size Above/Below Either Side Between airflow

mm in mm in mm in CFM (ft

/min) 1 50 1.97 50 1.97 33 1.30 11 2 75 2.95 50 1.97 46 1.81 11 3 100 3.94 50 1.97 52 2.05 26

Note: Dimension Z assumes that the drives are mounted side-by-side with no clearance.

Typical drive heat losses are 3% of operating load conditions.

Above are guidelines only and the operating ambient temperature of the drive MUST be maintained at all times.

4. POWER WIRING

4.1. GROUNDING THE DRIVE

This manual is intended as a guide for proper installation. ERIKS Industrial Services Ltd cannot assume responsibility for the compliance or the noncompliance to any code, national, local or otherwise, for the proper installation of this drive or associated equipment. A hazard of personal injury and/or equipment exists if codes are ignored during installation.

This drive contains high voltage capacitors that take time to discharge after removal of main supply. Before working on the drive, ensure isolation of main supply from line inputs. Wait ten (10) minutes for capacitors to discharge to safe voltage levels. Failure to observe this precaution could result in severe bodily injury or loss of life.

Only qualified electrical personnel familiar with the construction and operation of this equipment and the hazards involved should install, adjust, operate, or service this equipment. Read and understand this manual and other applicable manuals in their entirety before proceeding. Failure to observe this precaution could result in severe bodily injury or loss of life.

Use the dedicated ground terminal to ground the drive. Do not use mounting screws/bolts or chassis screws for grounding

4.1.1. GROUNDING GUIDELINES

The ground terminal of each Fenner drive should be individually connected DIRECTLY to the site ground busbar. Fenner drive ground connections should not loop from one drive to another, or to, or from any other equipment. Ground loop impedance must confirm to local industrial safety regulations. To meet UL regulations, UL approved ring crimp terminals should be used for all ground wiring connections. The drive Safety Ground must be connected to system ground. Ground impedance must conform to the requirements of national and local industrial safety regulations and/or electrical codes. The integrity of all ground connections should be checked periodically.

Ground Fault Monitoring

If a system ground fault monitor is to be used, only Type B devices should be used to avoid nuisance tripping.

Drives with an EMC filter have an inherently higher leakage current to Ground (Earth). For applications where tripping occurs the EMC filter can be disconnected by removing the EMC screw on the side of the product.

The Fenner QD product range has input supply voltage surge suppression components fitted to protect the drive from line voltage transients, typically originating from lightening strikes or switching of high power equipment on the same supply.

When carrying out a HiPot (Flash) test on an installation in which the drive is built, the voltage surge suppression components may cause the test to fail. To accommodate this type of system HiPot test, the voltage surge suppression components can be disconnected by removing the VAR screw. After completing the HiPot test, the screw should be replaced and the HiPot test repeated. The test should then fail, indicating that the voltage surge suppression components are once again in circuit.

Safety Ground

This is the safety ground for the drive that is required by code. One of these points must be connected to adjacent building steel (girder, joist), a floor ground rod, or bus bar. Grounding points must comply with national and local industrial safety regulations and/or electrical codes.

Motor Ground

The motor ground must be connected to one of the ground terminals on the drive.

Shield Termination (Cable Screen)

The safety ground terminal provides a grounding point for the motor cable shield. The motor cable shield connected to this terminal (drive end) should also be connected to the motor frame (motor end). Use a shield terminating or EMI clamp to connect the shield to the safety ground terminal. When shielded cable is used for control and signal wiring, the shield should be grounded at the source end only, not at the drive end.

4.2. WIRING PRECAUTIONS

Connect drive according to section 4.3 Connection Diagram, ensuring that motor terminal box connections are correct. There are two connections in general: Star and Delta. It is essential to ensure that the motor is connected in accordance with the voltage at which it will be operated. For more information, refer to section 4.5 Motor Terminal Box Connections. For recommended cabling and wiring sizing, refer to section 10.2 Rating tables. It is recommended that the power cabling should be 3-core or 4-core PVC-insulated screened cable, laid in accordance with local industrial regulations and codes of practice.

NOTE

Fenner QDE User Guide 9/5/08 9:23 AM Page 7

Installation & Operating Instructions

Page 9

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 8

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

4.3. CONNECTION DIAGRAM

4.4. D

RIVE AND MOTOR CONNECTIONS

For 1 phase supply power should be connected to L1/L, L2/N. For 3 phase supplies power should be connected to L1, L2, L3. Phase sequence is not important. The Motor should be connected to U, V, W For drives that have a dynamic brake transistor an optional external braking resistor will need be connected to +DC and BR when required. The brake resistor circuit should be protected by a suitable thermal protection circuit. Further information can be found in the Advanced User Guide. The –DC, +DC and BR connections are blanked off by plastic tabs when sent from the factory. The plastic tabs can be removed if/when required.

Size 1 Connections

Size 2 & 3 Connections

4.5. MOTOR TERMINAL BOX CONNECTIONS

Most general purpose motors are wound for operation on dual voltage supplies. This is indicated on the nameplate of the motor

This operational voltage is normally selected when installing the motor by selecting either STAR or DELTA connection. STAR always gives the higher of the two voltage ratings. Typical ratings are:

5.1. CONTROL TERMINAL CONNECTIONS

5.2. RJ45 DATA CONNECTION

6. OPERATION

6.1. MANAGING THE KEYPAD

The drive is configured and its operation monitored via the keypad and display.

Control Signal Description

Terminal

1 +24V User Output, +24V, 100mA.

2 Digital Input 1 Positive logic

“Logic 1” input voltage range: 8V … 30V DC

3 Digital Input 2

“Logic 0” input voltage range: 0V … 4V DC

Digital Input 3 / Digital: 8 to 30V

Analog Input 2 Analog: 0 to 10V, 0 to 20mA or 4 to 20mA

5 +10V User Output +10V, 10mA, 1kΩ minimum

Analog Input 1 / Analog: 0 to 10V, 0 to 20mA or 4 to 20mA

Digital Input 4 Digital: 8 to 30V

7 0V User ground connected terminal 9

Analog Output / Analog: 0 to 10V, 20mA maximum

Digital Output Digital: 0 to 24V

9 0V User ground connected terminal 7

10 Relay Common

11 Relay NO Contact Contact 250Vac, 6A / 30Vdc, 5A

Default

Connections

For MODBUS RTU register map

information please refer to the

Fenner QD:E Advanced User Guide.

When using MODBUS control the Analog

and Digital Inputs

can be configured as shown in section 8.3

NAVIGATE

DOWN

RESET/

STOP

START

Used to display real-time information, to access and exit parameter edit mode and to store parameter changes

Used to increase speed in real-time mode or to increase parameter values in parameter edit mode

Used to decrease speed in real-time mode or to decrease parameter values in parameter edit mode

Used to reset a tripped drive. When in Keypad mode is used to Stop a running drive

When in keypad mode, used to Start a stopped drive or to reverse the direction of rotation if bi-directional keypad mode is enabled

Fenner QDE User Guide 9/5/08 9:23 AM Page 9

Installation & Operating Instructions

Page 11

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 10

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

6.1.1. C

HANGING PARAMETERS

To change a parameter value press and hold the key for >1s whilst the drive displays STOP. The display changes to P-01, indicating parameter 01. Press and release the key to display the value of this parameter. Change to the required value using the and keys. Press and release the key once more to store the change. Press and hold the key for >1s to return to real-time mode. The display shows STOP if the drive is stopped or the real-time information (e.g. speed) if the drive is running.

6.1.2. RESET FACTORY DEFAULT SETTINGS

To reset factory default parameters, press , and for >2s. The display shows P-dEF. Press the button to acknowledge and reset the drive.

6.2. TERMINAL CONTROL

When delivered, the Fenner drive is in the factory default state, meaning that it is set to operate in terminal control mode and all parameters (P-xx) have the default values as indicated in section 7 Parameters.

1. Connect motor to drive, checking star/delta connection for the voltage rating

2. Enter motor data from motor nameplate, P-07 = motor rated voltage, P-08 = motor rated current, P-09 = motor rated frequency.

3. Connect a control switch between the control terminals 1 and 2 ensuring that the contact is open (drive disabled).

4. Connect a potentiometer (1kΩ min to 10 kΩ max) between terminals 5 and 7, and the wiper to terminal 6.

5. With the potentiometer set to zero, switch on the supply to the drive. The display will show STOP.

6. Close the control switch, terminals 1-2. The drive is now ‘enabled’ and the output frequency/speed are controlled by the potentiometer. The display shows zero speed in Hz (H

0.0) with the potentiometer turned to minimum.

7. Turn the potentiometer to maximum. The motor will accelerate to 50Hz (the default value of P-01) under the control of the accelerating ramp time P-03. The display shows 50Hz (H 50.0) at max speed.

8. To display motor current (A), briefly press the (Navigate) key.

9. Press again to return to speed display.

10. To stop the motor, either turn the potentiometer back to zero or disable the drive by opening the control switch (terminals 1-2).

If the enable/disable switch is opened the drive will decelerate to stop at which time the display will show STOP. If the potentiometer is turned to zero with the enable/disable closed the display will show H 0.0 (0.0Hz), if left like this for 20 seconds the drive will go into standby mode, display shows Stndby, waiting for a speed reference signal.

6.3. KEYPAD CONTROL

To allow the Fenner drive to be controlled from the keypad in a forward direction only, set P-12 =1:

1. Connect Motor as for terminal control above.

2. Enable the drive by closing the switch between control terminals 1 & 2. The display will show STOP.

3. Press the key. The display shows H 0.0.

4. Press to increase speed.

5. The drive will run forward, increasing speed until is released.

The rate of acceleration is controlled by the setting of P-03, check this before starting.

6. Press to decrease speed. The drive will decrease speed until is released. The rate of deceleration is limited by the setting in P-04

7. Press the key. The drive will decelerate to rest at the rate set in P-04.

8. The display will finally show STOP at which point the drive is disabled

9. To preset a target speed prior to enable, press the key whilst the drive is stopped. The display will show the target speed, use the & keys to adjust as required then press the key to return the display to STOP.

10. Pressing the key will start the drive accelerating to the target speed.

To allow the Fenner drive to be controlled from the keypad in a forward and reverse direction, set P-12 =2:

11. Operation is the same as when P-12=1 for start, stop and changing speed.

12. Press the key. The display changes to H 0.0.

13. Press to increase speed

14. The drive will run forward, increasing speed until is released. Acceleration is limited by the setting in P-03. The maximum speed is the speed set in P-01.

15. To reverse the direction of rotation of the motor, press the

key again.

7. PARAMETERS

7.1. STANDARD PARAMETERS

Default parameter values for Horse Power rated drives are shown in brackets Standby mode is enabled automatically when the drive is at zero speed for > 20 seconds

NOTE

Par. Description Range Default Explanation

P-01 Maximum speed P-02 to 5*P-09 (max 500Hz) 50Hz (60Hz) Maximum speed limit – Hz or rpm. See P-10

P-02 Minimum speed 0 to P-01 (max 500Hz) 0Hz Minimum speed limit – Hz or rpm. See P-10

P-03 Acceleration ramp

0 to 600s 5s

Acceleration ramp time from 0 to base speed

time (P-09) in seconds

Deceleration ramp time from base speed (P-09) to standstill in seconds.

P-04

Deceleration ramp 0 to 600s 5s When P-04=0, the deceleration ramp is set by P-24.

time Setting P-04=0 also activates dynamic ramp control,

where the ramp may be extended automatically to prevent an O-Volt trip.

If the supply is lost and P-05=0 then the drive will

0 : Ramp stop try to continue running by reducing the speed of

P-05 Stop mode select

(brown-out ride-through) 0 the load using the load as a generator. 1 : Coast to stop If P-05 = 2, the drive will ramp to stop using the

2 : Ramp to stop (fast stop) P-24 decel ramp with dynamic brake control when

mains supply lost.

0: Disabled

When enabled, automatically reduces applied

P-06 Energy Optimiser

1: Enabled

0 motor voltage on light load. Minimum value is

50% of nominal.

0, 20V to 250V 230V

Rated (nameplate) voltage of the motor (Volts).

P-07 Motor rated voltage

0, 20V to 500V 400V (460V)

Value limited to 250V for low voltage drives. Setting to zero disables voltage compensation

P-08 Motor rated current 25% -100% of drive rated current Drive rating Rated (nameplate) current of the motor (Amps).

P-09

Motor rated

25Hz to 500Hz 50Hz (60Hz)

Rated (nameplate) frequency of the motor.

frequency

P-10 Motor rated speed 0 to 30 000 rpm 0

When non-zero, all speed related parameters are displayed in rpm

Size 1: 0.0 to 20.0% Applies an adjustable boost to the Fenner drive voltage

P-11

Voltage boost

Size 2: 0.0 to 15.0% Motor power output at low speed to assist with starting ‘sticky’ Size 3: 0.0 to 10.0% dependent loads. For continuous applications at low speed use of max output voltage. a forced ventilated motor.

Primary Control Mode of the drive.

0. Terminal control

0.Terminal control 1. Uni-directional keypad control. Keypad START

1. Keypad control – fwd only button does not reverse direction. Terminal / Keypad / 2. Keypad control - fwd and rev 2. Bi-directional keypad control. Keypad START MODBUS / PI 3. MODBUS network control with button toggles between forward and reverse.

P-12 Drive Control internal accel / decel ramps 0 3. Control via Modbus RTU (RS485) comms

Mode Selection 4. MODBUS network control withl interface using the internal accel / decel ramps

accel / decel ramp adjustment 4. Control via Modbus RTU (RS485) comms

5. User PI control nterface with accel / decel ramps updated via

6. User PI control with analog input Modbus

1 summation 5. User PI control with external feedback signal

6. User PI control with external feedback signal and summation with analog input 1 Previous 4 trips stored in order of occurrence, with the most recent first.

Press UP or DOWN to step through all four.

P-13 Trip log Last four trips stored Read only The most recent trip is always displayed first.

UV trip is only stored once. Further fault event logging functions are available through parameter group zero.

Set to “101” (default) for extended menu access.

P-14

Extended menu

Code 0 to 9 999 0 Change code in P-39 to prevent unauthorised

access

access to the Extended Parameter Set

Fenner QDE User Guide 9/5/08 9:23 AM Page 11

Installation & Operating Instructions

Page 13

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 12

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

7.1. STANDARD PARAMETERS

Par. Description Range Default Explanation

Defines the function of the digital inputs depending

P-15

Digital input

0 to 12 0

on the control mode setting in P-12.

function selec See section 8 Analog and Digital Input

Configurations for more information. Configures the voltage or current format of the

analog input signal. b 0..10V can be used for bipolar input signals. A

0..10V, b 0..10V, 0..20mA, 50% offset can be applied to P-39 and 200%

P-16 Analog input format t 4..20mA, r 4..20mA, 0..10V scaling in P-35 gives ± P-01

t 20..4mA r 20..4mA “t” indicates the drive will trip if signal removed

when drive is enabled. “r” indicates the drive will ramp to Preset Speed 1 if signal is removed when drive is enabled

Sets maximum effective switching frequency of the

P-17 Effective switching 4 .. 32kHz 8 / 16kHz drive. If “rEd” is displayed, the switching frequency

frequency has been reduced to the level in P00-14 due to

excessive drive heatsink temperature.

0 : Drive enabled Defines the function of the user relay, when the 1 : Drive healthy operating conditions are met. 2 : Motor at target speed Disabled : Contacts open

P-18 User relay output 3 : Drive tripped Enabled : Contacts closed

select 4 : Motor speed >= limit 1

5 : Motor current >= limit Options 4 to 7: the Relay output is enabled using 6 : Motor speed < limit the level set in P-19 7 : Motor current < limit

P-19

User relay output 0.0 to 100% for speed

100%

Sets the limit for P-18 & P-25

limit 0.0 to 200% for current

P-20 Preset speed 1 -P-01 to P-01 0 Hz Sets jog / preset speed 1 P-21 Preset speed 2 -P-01 to P-01 0 Hz Sets jog / preset speed 2 P-22 Preset speed 3 -P-01 to P-01 0 Hz Sets jog / preset speed 3 P-23 Preset speed 4 -P-01 to P-01 0 Hz Sets jog / preset speed 4

2nd Deceleration ramp time from base speed (P-09)

P-24

2nd decel ramp time to standstill in seconds. (Fast Stop) 0…25.0s 0 Selected using fast stop function via digital input

setting or on mains loss as set by P-05 If set to zero drive will coast to STOP.

Digital output mode Digital Output Mode 0 : Drive enabled Options 0 to 7 select a digital voltage output signal 1 : Drive healthy Disabled : 0V 2 : Motor at target speed Enabled : +24V, (20mA limit) 3 : Drive tripped Options 4 to 7 : the Digital output is enabled using

P-25 Analog output 4 : Motor speed >= limit 8 the level set in P-19

function select 5 : Motor current >= limit Analog Output Mode

6 : Motor speed < limit Option 8 : Motor Speed signal range 7 : Motor current < limit 0..10V = 0..100% of P-01 Analog output mode Option 9 : Motor Current signal range 8 : Motor speed 0..10V = 0..200% of P-08 9 : Motor current

Set P-09 before adjusting.

Skip frequency

Speed reference held at upper or lower skip

P-26

hysteresis band

0 to P-01 0 Hz frequency limit until input signal reaches the

opposite skip frequency limit. Speed ramps through the skip frequency band at a rate set by P-03 and P-04.

P-27

Skip frequency P-02 to P-01

0 Hz

Set P-09 before adjusting. Skip frequency centre point

P-28

V/F characteristic

0 … P-07 0

Adjusts the applied motor voltage to this value at

adjustment voltage the frequency set in P-29

Sets the frequency at which the adjustment voltage set in P-28 is applied

0 … P-09

0.0Hz

Edge-r : if drive is powered up with Digital Input 1

P-29

V/F characteristic

closed (enabled), drive will not run. The switch must

frequency adjust

be opened & closed after power up or after clearing a trip for the drive to run.

Auto-0 : drive will run whenever digital input 1 is closed (if not tripped).

Terminal mode Auto-1..5 : drive will make 1..5 attempts to

P-30

restart function EdgE-r, Auto-0 .. Auto-5 Auto-0 automatically restart after a trip (25s between

attempts). If fault has cleared drive will restart. To reset the counter the Drive must be powered down, reset on the keypad or by re-enabling the drive.

If set to 0 or 2, drive will always start from

0 : Minimum speed minimum speed.

Keypad mode 1 : Previous speed If set to 1 or 3, drive ramps up to the operating

P-31 restart function 2 : Minimum speed (Auto-run) 1 speed prior to the last STOP command.

3 : Previous speed (Auto-run) If set to 2 or 3, the status of digital input 1 controls.

drive to start or stop. The start and stop button on the drive will not function in this case.

When > 0, DC injection braking activated when

0 to 25.0s 0 speed reaches zero with stop signal applied.

P-32

DC injection on stop (disabled) Only applied on disable (Stop), not on enable.

Uses the level set in P-11.

When enabled, drive starts from detected motor rotor speed. Short start delay possible if rotor

Spin Start 0 : Disabled stationary. Recommended for high inertia load

P-33 (S2 & S3 only) 1 : Enabled 0 applications.

DC injection on For Size 1 drives, P-33 = 1 enables DC injection start (S1) braking on enable. The duration and levels are set

by P-32 and P-11 respectively.

Brake chopper Software protection for Fenner standard brake

P-34

enable (not S1) 0 : Disabled resistors (200W).

1 : Enabled with s/w protection For Non-Fenner approved resistors and higher 2 : Enabled without s/w protection 0 braking applications set to 2.

P-35 Analog input scaling 0 … 500.0% 100% Analog input scaling, resolution 0.1%.

Serial Adr : 0 disable, 1..63 Adr : Unique drive address for communication Communications 1 network address When set to OP-buS, MODBUS disabled. MODBUS enable / OP-buS (fixed at 115.2 kbps) 0P-buS Communication with PDA, PC and QPort:E baudrate select 9.6k to 115.2kbps (Modbus) possible

Setting a baudrate enables MODBUS at that baudrate and disables OP-buS.

0 (no trip) t 3000 The time before a trip in the event of a

P-36 Trip enable / delay t 30, 100, 1000, 3000 (ms) (3 second trip) communication loss can be set in milliseconds.

r 30, 100, 1000, 3000 (ms)) Setting “0” disables the communications trip.

“t” indicates the drive will trip if time exceeded. “r” indicates the drive will ramp to stop if time exceeded.

P-37

Access code

0 to 9 999

101

Defines Extended Parameter Set access code, P-14

definition

0: Parameters can be changed &

Controls user access to parameters. When P-38 = 0,

P-38

Parameter access

automatically saved on power down

all parameters can be changed and will be stored

lock

1: Read-only. No changes allowed.

automatically. When P-38 = 1, parameters are locked and cannot be changed.

P-39 Analog input offset -500.0 … 500.0% 0%

Introduces an offset to the analog input level with a resolution 0.1%. e.g. 10% = 1V = 0Hz

Custom scaling factor applied to drive speed. If P-10

P-40

Display speed

0.000 to 6.000

= 0, speed in Hz scaled by this factor. If P-10 > 0,

scaling factor speed in RPM scaled. Displayed as real-time

variable on the drive display, indicated by a “c”.

P-41

User PI Proportional

0.0 ... 30.0 1.0

Higher value used for high inertia. Too high a value

Gain gives instability.

P-42

User PI Integral

0.0s ... 30.0s 1.0s Higher value gives slower, more damped response. time constant

P-43

User PI operating 0: Direct 0 If an increasing feedback signal should increase the mode 1: Inverse speed of the motor, set to ‘Inverse’ mode.

P-44

User PI reference 0: Digital Sets the source for the PI control reference signal. select 1: Analog

When set to 1, analog input 1 is used.

P-45

User PI digital

0 … 100% 0.0 % Sets the preset reference used when P-44 = 0.

reference

User PI feedback 0 : 2nd analog input (T4)

P-46 select 1 : 1st analog input (T6) 0 This parameter selects the feedback signal source.

2 : motor load current

Selects the format of the 2nd analog input.

2nd analog input 0..10V, 0..20mA, “t” indicates the drive will trip if signal removed

P-47 format t 4..20mA, r 4..20mA, 0 ..10V when drive is enabled.

t 20..4mA r 20..4mA “r” indicates the drive will ramp to Preset Speed 1

if signal is removed when the drive is enabled

Fenner QDE User Guide 9/5/08 9:23 AM Page 13

Installation & Operating Instructions

Page 15

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 14

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

DJUSTING THE VOLTAGE / FREQUENCY (V/F) CHARACTERISTICS

The V/f characteristic is defined by several parameters as shown. Reducing the voltage at a particular frequency reduces the current in the motor and hence the torque and power. The V/f curve can be further modified by using P-28 and P-29, where P-28 determines the percentage increase or decrease of the voltage applied to the motor at the frequency specified in P-29. This can be useful if motor instability is experienced at certain frequencies, if this is the case increase or decrease the voltage (P-28) at the speed of instability (P-29).

For applications requiring energy saving, typically HVAC and pumping, the energy optimiser (P-06) parameter can be enabled. This automatically reduces the applied motor voltage on light load.

P-00 READ ONLY DRIVE STATUS PARAMETERS

7.2.1. PARAMETER GROUP ZERO ACCESS AND NAVIGATION

When P-14 = P-37, all P-00 parameters are visible. Default value is 101.

When the user scrolls to P-00, pressing will display “P00-HH”, where HH represents the secondary number within P-00. (i.e. 1 to 20). The User can then scroll to the required P-00 parameter.

Pressing once more will then display the value of that particular group zero parameter.

For those parameters which have multiple values (e.g. software ID), pressing the and keys will display the different values within that parameter.

Pressing returns to the next level up. If is then pressed again (without pressing or ), the display changes to the next level up (main parameter level, i.e. P-00).

If or is pressed whilst on the lower level (e.g. P00-05) to change the P-00 index, pressing <NAVIGATE> quickly displays that parameter value.

8. ANALOG AND DIGITAL INPUT CONFIGURATIONS

8.1. TERMINAL MODE (P-12 =0)

Negative Preset Speeds will be inverted if Run Reverse selected.

NOTE

TYPICAL APPLICATIONS

Analog speed input with 1 preset speed

and fwd/rev switch

Analog speed input with 2 preset speeds 4 preset speeds and max speed select

switch. Effectively giving 5 preset speeds

Description Display range Explanation

P00-01 1st Analog input value 0 … 100% 100% = max input voltage

P00-02 2nd Analog input value 0 … 100% 100% = max input voltage

P00-03 Speed reference input -P1-01 … P1-01 Displayed in Hz if P-10 = 0, otherwise displayed in RPM

P00-04 Digital input status Binary value Drive digital input status

P00-05 Reserved 0 Reserved

P00-06 Reserved 0 Reserved

P00-07 Applied motor voltage 0 … 600V AC Value of RMS voltage applied to motor

P00-08 DC bus voltage 0 … 1000V dc Internal DC bus voltage

P00-09 Internal Heatsink temperature -20 … 100 °C Temperature of heatsink in °C

P00-10 Hours run meter 0 to 99 999 hours Not affected by resetting factory default parameters

Run-time clock stopped by drive disable (or trip), reset on next

P00-11 Run time since last trip (1) 0 to 99 999 hours enable only if a trip occurred. Reset also on next enable after a drive

power down.

Run-time clock stopped by drive disable (or trip), reset on next

P00-12 Run time since last trip (2) 0 to 99 999 hours

enable only if a trip occurred (under-volts not considered a trip) – not reset by power down / power up cycling unless a trip occurred prior to power down

P00-13 Run time since last disable 0 to 99 999 hours Run-time clock stopped on drive disable, value reset on next enable

Actual drive effective output switching frequency. This value maybe

P00-14

Drive Effective Switching 4 to 32 kHz

lower than the selected frequency in P-17 if the drive is too hot.

Frequency

The drive will automatically reduce the switching frequency to prevent an over temperature trip and maintain operation.

P00-15 DC bus voltage log 0 … 1000V 8 most recent values prior to trip, updated every 250ms

P00-16 Thermistor temperature log -20 … 120 °C 8 most recent values prior to trip, updated every 500ms

P00-17 Motor current 0 to 2x rated current 8 most recent values prior to trip, updated every 250ms

Version number and checksum.

P00-18 Software ID, IO & motor ctrl e.g. “1.00”, “47AE” “1” on LH side indicates I/O processor,

“2“ indicates motor control

P00-19 Drive serial number

000000 … 999999 Unique drive serial number

00-000 … 99-999 e.g. 540102 / 32 / 005

P00-20 Drive identifier Drive rating

Drive rating, drive type e.g. 0.37, 1 230,3P-out

P-15 Digital input 1 (T2) Digital input 2 (T3) Digital input 3 (T4) Analog input (T6) Comments

Open: Stop (disable) Open : Forward run Open : Analog speed ref

Analog input 1 reference

Closed: Run (enable) Closed : Reverse run Closed : Preset speed 1

Open: Stop (disable) Open: Analog speed ref Open: Preset speed 1

Analog input 1 reference

Closed: Run (enable) Closed:Preset speed 1/2 Closed:Preset speed 2

Open: Stop (disable) Digital Input 2 Digital Input 3 Preset Speed 4 Preset speeds Closed: Run (enable) Open Open Preset Speed 1 Open: Preset speeds 1-4 selectable.

2 Closed Open Preset Speed 2 Closed:Max Speed(P-01) Analog input used as

Open Closed Preset Speed 3 digital input Closed status: Closed Closed Preset Speed 4 8V < Vin < 30V

Open: Stop (disable) Open : Analog speed ref External trip input : Connect external

Closed: Run (enable) Closed : Preset speed 1 Open: Trip, Analog input 1 reference thermistor type PT100 or

Closed: Run similar to digital input 3

Open: Stop (disable) Open : Analog input 1

Analog input 2 reference Analog input 1 reference

Switches between analog

Closed: Run (enable) Closed : Analog input 2 inputs 1 and 2

Open: Fwd Stop Open: Reverse Stop Open : Analog speed ref Closing digital inputs 1

5 Closed: Fwd Run Closed: Reverse Run Closed : Preset speed 1 Analog input 1 reference and 2 together carries out

a fast stop (P-24)

Open: Stop (disable) Open : Forward External trip input : Connect external

Closed: Run (enable) Closed : Reverse Open: Trip, Analog input 1 reference thermistor type PT100 or

Closed: Run similar to digital input 3

Open: Stop (disable) Open: Stop (disable) External trip input : Closing digital inputs 1

7 Closed: Fwd Run (enable) Closed: Rev Run (enable) Open: Trip, Analog input 1 reference and 2 together carries

Closed: Run out a fast stop (P-24)

Digital Input 3 Analog Input 1 Preset Speed

Open: Stop (disable) Open : Forward Open Open Preset Speed 1

8 Closed: Run (enable) Closed : Reverse Closed Open Preset Speed 2

Open Closed Preset Speed 3 Closed Closed Preset Speed 4

Digital Input 3 Analog Input 1 Preset Speed

Open: Stop (disable) Open: Stop (disable) Open Open Preset Speed 1 Closing digital inputs 1

9 Closed: Forward Run Closed: Reverse Run Closed Open Preset Speed 2 and 2 together carries out

(enable) (enable) Open Closed Preset Speed 3 a fast stop (P-24)

Closed Closed Preset Speed 4

Normally Open (NO) Normally Closed (NC) Open : Analog speed ref

Analog input 1 reference

Momentary close to run Momentary open to stop Closed:Preset speed 1

Normally Open (NO) Normally Closed (NC) Normally Open (NO) Closing digital inputs 1

11 Momentary close to run Momentary open to stop Momentary close to rev Analog input 1 reference and 3 together carries out

a fast stop (P-24)

Open: Stop (disable) Open: Fast Stop (disable) Open : Analog speed ref

Analog input 1 reference

Closed: Run (enable) Closed: Run (enable) Closed : Preset speed 1

Fenner QDE User Guide 9/5/08 9:23 AM Page 15

Installation & Operating Instructions

Page 17

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 16

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

Analog speed input with 1 preset speed

and motor thermistor trip

Local or remote analog speeds

(2 analog inputs)

Push button fwd/rev/stop with fast stop

using 2nd deceleration ramp

8.2. KEYPAD MODE (P-12 = 1 OR 2)

EXAMPLE WIRING

Remote push button speed control with

fwd/rev

Analog speed input with 2 preset speeds

By default if the enable signal is present the drive will not Enable until the START button is pressed. To automatically enable the drive when the enable signal is present set P-31 = 2 or 3. This then disables the use of the START & STOP buttons

NOTE

8.3. MODBUS CONTROL MODE (P12 = 3 OR 4)

Further information the MODBUS RTU Register Map information and communication setup; please refer to the Advanced User Guide.

8.4. USER PI CONTROL MODE (P-12 = 5 OR 6)

EXAMPLE WIRING

Remote closed loop PI feedback control

with Local Preset speed 1

Remote closed loop PI feedback control

with Local Analog speed input

Remote closed loop PI feedback control

with Local Preset speed 1 and motor

thermistor trip

By default the PI reference is set for a digital reference level set in P-45. When using an Analog reference set P-44 = 1 (analog) and connect reference signal to analog input 1 (T6). The default settings for proportional gain (P-41), integral gain (P-42) and feedback mode (P-43) are suitable for most HVAC

and pumping applications.

The analog reference used for PI controller can also be used as the local speed reference when P15=1.

NOTE

Further information on configuring the PI controller for typical feedback applications; please refer to the Advanced User Guide.

P-15 Digital input 1 (T2) Digital input 2 (T3) Digital input 3 (T4) Analog input (T6) Comments

0, 1,

Open: Stop (disable) Closed : remote UP Closed : remote DOWN Open : Forward

Closed: Run (enable) push-button push-button +24V : Reverse

8..12

Open: Stop (disable) Closed : remote UP Closed : remote DOWN Open : Keypad speed ref Closed: Run (enable) push-button push-button +24V : Preset speed 1

Open: Stop (disable) Closed : remote UP External trip input : Closed : remote DOWN

Connect external

Closed: Run (enable) push-button Open: Trip, Closed: Run push-button

thermistor type PT100 or similar to digital input 3

Open: Stop (disable) Closed : remote UP Open : Keypad speed ref

Analog input 1

Closed: Run (enable) push-button Closed : Analog input 1

Open: Stop (disable) Open : Forward run External trip input : Open : Keypad speed ref

Connect external

Closed: Run (enable) Closed : Reverse run Open: Trip, Closed: Run +24V : Preset speed 1

thermistor type PT100 or similar to digital input 3

Open: Forward Stop Open: Reverse Stop External trip input : Open : Keypad speed ref

Closing digital inputs 1

Closed: Forward Run Closed: Reverse Run Open: Trip, Closed: Run +24V : Preset speed 1

and 2 together carries out a fast stop (P-24)

P-15 Digital input 1 (T2) Digital input 2 (T3) Digital input 3 (T4) Analog input (T6) Comments

0..2,

Run and stop commands

4..5,

Open: Stop (disable)

No effect No effect No effect

given via the RS485 link

8..12

Closed: Run (enable) and Digital input 1 must be

closed for the drive to run.

Open: Stop (disable) Open : Master speed ref External trip input :

Connect external

Closed: Run (enable) Closed : Preset speed 1 Open: Trip, Closed: Run

No effect thermistor type PT100 or

similar to digital input 3

Open: Stop (disable) Open : Master speed ref External trip input : Analog input reference Master Speed Ref - start Closed: Run (enable) Closed : Analog input Open: Trip, Closed: Run and stop controlled via

RS485. Keypad Speed Ref

Open: Stop (disable) Open : Master speed ref External trip input :

No effect

- drive auto runs if digital

Closed: Run (enable) Closed : keypad speed ref Ope n: Trip, Closed: Run input 1 closed, depending

on P-31 setting

P-15 Digital input 1 (T2) Digital input 2 (T3) Digital input 3 (T4) Analog input (T6) Comments

0, 2,

Open: Stop (disable) Open : PI control

PI feedback analog input No effect

4..5,

Closed: Run (enable) Closed : Preset speed 1

8..12

Open: Stop (disable) Open : PI control

PI feedback analog input Analog input 1

Closed: Run (enable) Closed : Analog input 1

3, 6, Open: Stop (disable) Open : PI control External trip input :

Connect external

Closed: Run (enable) Closed : Preset speed 1 Open: Trip, Closed: Run PI feedback analog input

thermistor type PT100 or similar to digital input 3

Fenner QDE User Guide 9/5/08 9:24 AM Page 17

Installation & Operating Instructions

Page 19

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Page 18

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

9. TROUBLESHOOTING

9.1. FAULT MESSAGES

10. T

ECHNICAL DATA

10.1. ENVIRONMENTAL

Operational ambient temperature range: 0 … 50°C (frost and condensation free) Storage ambient temperature range: -40 … 60°C Maximum altitude: 2000m. Derate above 1000m : 1% / 100m Maximum humidity: 95%, non-condensing

10.2. RATING TABLES

kW HP Frame Nominal Input Supply Nominal 150% Motor Max Min

Size Input MCB Cable Output Output Cable Motor Brake

Current (type B) Size Current Current Size Cable Res

60secs Length Value

Amps Amps mm2 Amps Amps mm2 m Ω

0.37 0.5 1 6.7 6 1.5 2.3 3.45 1.5 25 -

0.75 1 1 12.5 10 1.5 4.3 6.45 1.5 25 -

1.5 2 1 19.3 20 4 7 10.5 1.5 25 -

1.5 2 2 19.3 20 4 7 10.5 1.5 100 47

2.2 3 2 28.8 32(35)* 4 10.5 15.75 1.5 100 47

200-240V ±10% - 1 Phase Input – 3 Phase Output

kW HP Frame Nominal Input Supply Nominal 150% Motor Max Min

Size Input MCB Cable Output Output Cable Motor Brake

Current (type B) Size Current Current Size Cable Res

60secs Length Value

Amps Amps mm2 Amps Amps mm2 m Ω

0.37 0.5 1 3 6 1.5 2.3 3.45 1.5 25 -

0.75 1 1 5.8 10 1.5 4.3 6.45 1.5 25 -

1.5 2 1 9.2 16(15)* 2.5 7 10.5 1.5 25 -

1.5 2 2 9.2 16(15)* 2.5 7 10.5 1.5 100 47

2.2 3 2 13.7 20 4 10.5 15.75 1.5 100 47

4.0 5 3 20.7 32(35)* 4 18 27 2.5 100 47

200-240V ±10% - 3 Phase Input – 3 Phase Output

kW HP Frame Nominal Input Supply Nominal 150% Motor Max Min

Size Input MCB Cable Output Output Cable Motor Brake

Current (type B) Size Current Current Size Cable Res

60secs Length Value

Amps Amps mm2 Amps Amps mm2 m Ω

0.75 1 1 2.9 5 1.5 2.2 3.3 1.5 25 -

1.5 2 1 5.4 10 1.5 4.1 6.15 1.5 25 -

1.5 2 2 5.4 10 1.5 4.1 6.15 1.5 100 47

2.2 3 2 7.6 10 1.5 5.8 8.7 1.5 100 47

4 5 2 12.4 16(15)* 2.5 9.5 14.25 1.5 100 47

5.5 7.5 3 17.6 20 4 14 21 2.5 100 22

7.5 10 3 22.1 25 4 18 27 2.5 100 22

11 15 3 28.2 32(35)* 6 24 36 4 100 22

380-480V ±10% - 3 Phase Input – 3 Phase Output

Output Frequency range: 0 - P-01 (500Hz max) For UL compliance Motor Cable to be Copper 75C and Fuse current rating defined by ratings marked ( )*

10.3. MAXIMUM SUPPLY RATINGS FOR UL COMPLIANCE:

All the drives in the above table are suitable for use on a circuit capable of delivering not more than the above specified maximum short-circuit Amperes symmetrical with the specified maximum supply voltage.

Drive rating Maximum supply voltage Maximum supplyshort-circuit current

230V ratings – 0.37kW (0.5HP) to 3.7kW (5HP) 240V rms (AC) 5kA rms (AC)

400/460V ratings – 0.75kW(1HP) to 7.5kW(10HP) 480V rms (AC) 5kA rms (AC)

P-15 Digital input 1 (T2) Digital input 2 (T3)

P-dEF

Factory Default parameters Press STOP key, drive is ready to configure for particular application have been loaded

Motor at constant speed: investigate overload or malfunction.

Over current on drive output. Motor starting: load stalled or jammed. Check for star-delta motor

O-I

Excess load on the motor. wiring error. Over temperature on the Motor accelerating/decelerating: The accel/decel time too short drive heatsink requiring too much power. If P-03 or P-04 cannot be increased, a

bigger drive is required. Cable fault between drive and motor.

Drive has tripped on overload Check to see when the decimal points are flashing (drive in overload) after delivering >100% of and either increase acceleration ramp (P-03) or decrease motor load.

I. t-trP value in P-08 for a period of Check cable length is within drive specification. Check the load

time. mechanically to ensure it is free, and no jams, blockages or other

mechanical faults exist

Over current in the brake resistor circuit. Check the cabling to the

OI-b Brake channel over current brake resistor. Check the brake resistor value. Ensure minimum

resistance values form the rating tables are observed.

Brake resistor overload. Increase deceleration time, reduce load

OL-br Brake resistor overload inertia or add further brake resistors in parallel. Ensure minimum

resistance values form the rating tables are observed.

Check wiring to motor, look for ph-ph or ph-Earth short circuit.

PS-trp Internal power stage fault Check drive ambient temp, additional space or cooling needed?

Check drive is not forced into overload.

O.Uolt Over voltage on DC bus Supply problem, or increase decel ramp time P-04.

U.Uolt Under voltage on DC bus

This occurs routinely when power is switched off. If it occurs during running, check power supply voltage.

O-t Heatsink over temperature Check drive ambient temp. Additional space or cooling required.

U-t Under temperature

Trip occurs when ambient temperature is less than -10°C. Temperature must be raised over -10°C in order to start the drive.

th-Flt Faulty thermistor on heatsink. Refer to your local Fenner authorised distributor.

External trip

E-trip requested on digital input 3. Normally closed contact has

E-triP

(on digital Input 3)

opened for some reason. If motor thermistor is connected check if the motor is too hot.

SC-trP Comms loss trip

Check communication link between drive and external devices. Make sure each drive in the network has its unique address.

P-LOSS Input phase loss trip

Drive intended for use with a 3 phase supply has lost one input phase.

SPIn-F Spin start failed Spin start function failed to detect the motor speed.

data-F Internal memory fault.

Parameters not saved, defaults reloaded. Try again. If problem recurs, refer to your local Fenner authorised distributor.

4-20 F

Analog input current out of

Check input current in range defined by P-16.

range

SC-FLt Internal drive Fault Refer to your local Fenner authorised distributor.

FAULTY Internal drive Fault Refer to your local Fenner authorised distributor.

Fenner QDE User Guide 9/5/08 9:24 AM Page 19

Page 20

www.fptgroup.com

Fenner is a registered trademark of J.H. Fenner & Co. Limited

Installation & Operating Instructions

Fenner®QD:E

Fenner QDE User Guide 9/5/08 9:24 AM Page 21

Fenner QDE User Guide 9/5/08 9:24 AM Page 23

Fenner QD:E Installation And Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual