FengShun Peiying Electro Acoustic MPQ914 User Manual

MPQ914

Wiring Diagram-Inputs/Outputs

TYPICPAL FRONT-LOAD DIN
MOUNTING METHOD

Button Operation

To download a complete owner’s manual

visit www.jensenmobile.com

or call customer service

1-888-921-4088

(Monday-Friday,9AM-5PM EST)

With the unit on, long press DISP to display clock time. Press and
hold DISP until the hours or minutes begin to flash, then
release. Rotate the volume knob to adjust the time.
Long press DISP to finish the clock setting.

IGNITION / ACC 12V(+) RED

BATTERY 12V (+) YELLOW

CHASSIS GROUND BLACK

REMOTE TURN-ON(+)
POWER ANTENNA (+)

WHITE

WHITE/BLACK

GRAY

GRAY/BLACK

GREEN

GREEN/BLACK

DARK BLUE

Touch PS to recall each preset station that has been
stored in memory for each band.
(Available with the Dual Smart Remote App only)

VIOLET

VIOLET/BLACK

FRONT LEFT SPEAKER

FRONT RIGHT SPEAKER

REAR LEFT SPEAKER

REAR RIGHT SPEAKER

MENU

,then press DISP

Front panel USB port support 1A charging/Play­back.

1.Mute/Power

2.Voice Activation

3.Open

4.End Call

5.USB

6.Aux Input

7.Folder Up

8.Folder Down

9.Play/Pause

Preparation

Pairing a New

Device

Streaming Audio

Troubleshooting

10.Introduce

11.Random

12.Reapt

13.Band/Disp

14.Mode

15.VOL Up/Down/Menu

16.Tune/Track Up

17.MIC

18.Tune/Track Down

Bluetooth®

Before using a Bluetooth device, it must be paired and
connected. Ensure that Bluetooth is activated on your
device before beginning the pairing process.

The head unit broadcasts the pairing signal constantly
when no devices are connected. Complete the pairing
sequence from your Bluetooth device. Refer to the
owner’s manual for your device for more details.

The device name is "Dual Media Player"
The Bluetooth passcode is "1234”

Note: If passcode "1234" does not pair your device to
the receiver, use passcode "0000".

Note: The head unit can be in any mode of operation
when pairing is performed.

The head unit supports A2DP wireless streaming audio
from a Bluetooth mobile device directly to your head unit.
The following functions can be used to control the music:

•

Press

ll

Press

•

nn

Press

•

l

playback.

/

Operation

to skip to the next available audio track.
to skip to the previous audio track.

II to toggle between play and pause during

Wireless Charging Operation

Putting Phone
on Wireless
Charging Pad

Charging Status

Phone Removal

LED Indicator：

LED I ndica tion St andby N ormal C hargi ng Fast C hargi ng Full F OD/Er ror Low P ower Ov er Temp eratu re

LED -A(Re d)

LED -B(Gr een)

Press the Open button on the front panel, and the
Wireless Charging Pad will automatically pop up
from the unit. Open the Wireless Charging Pad
switch after the pad has completely slid into the
position, and open the buckle on the top of the pad
to support the phone (With Wireless Charging
Function) and put down the buckle tightly.

After the phone enters charging mode, it’s in
normal charging mode when the red and green
LED indicator on the pad has 3S flashing. It starts
to enter the fast charge mode after the red LED
indicator off and the green LED indicator has 3S
flashing. The green LED indicator is always on
when the phone is fully charged.

If you don't need to charge it, please lift up the
buckle on top of the pad and remove the phone,
then close the wireless charging switch under the
pad and press the Open button on the front panel
to retract the wireless charging pad automatical­ly.
If the wireless charging switch on the pad is not
closed, the unit will not perform the wireless
charging pad retraction when you press the Open
button on the front panel, and it will display the
"CHARGE" warning on the LCD.

Off a fter
10S O n

Off

3S Fl ashin g

Off OffOff OffOn

3S Fl ashin g3S Fl ashin g

0.5 S Flash ing 0.5 S Flash ing

On

Off

Step #1

Step #2

Step #3

Step #4

Wireless Charging sequence

Press OPEN to open or close the
wireless charging pad.

Open phone holder on the
bottom of the pad.

Note – Use the phone holder
on the top of the pad in order to
hold the smartphone more firmly.

Put the smartphone on wireless charging
pad for wireless charge.

Note - Here is the information on
LED indicator for charging status
Charging : Green & Red
Fully Charged : Green

Press OPEN to close the
wireless charging pad.
Note - The pad will not be
closed if the phone holder is
still open.

APP Operation

The Jensen Smart App is the ultimate wireless remote control for your
receiver. You can download Jensen Smart app from Apple App Store or
Google Play Store and install it on your smartphone or tablet.

Please scan the following QR code to download Jensen J Link APP P2 to
your smart phone.

Voice Activation Operation

Bluetooth should be paired between your smartphone and the receiver.
Press the voice activation button , and the receiver will switch into Bluetooth mode,
This will activate Siri® or Google AssistantTM on your smartphone. You will need to manually
switch back to the previous or desired mode once this operation is terminated.

To download the complete Owner’s Manual for your radio,

please visit www.dualav.com/support/manuals.php.

Namsung America Inc.

Namsung America Inc.

1-888-921-4088

FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set
forth for uncontrolled enviroment. This equipment should be
installed and operated with minimum distance 20cm between the

radiator and your body.

FCCID: 2AFXA-MPQ914

www.jensenmobile.com

©2019 Namsung America Inc.

NSA1019-V01