Fendt 700 vario, 800 vario, 900 vario Service Manual

SmarTrax™ MD Installation Manual

Fendt Vario 700, 800, and 900 Series

Disclaimer

While every effort has been made to ensure the accuracy of this document,
Raven Industries assumes no responsibility for omissions and errors. Nor is any
liability assumed for damages resulting from the use of information contained
herein.

Raven Industries shall not be responsible or liable for incidental or consequential
damages or a loss of anticipated benefits or profits, work stoppage or loss, or
impairment of data arising out of the use, or inability to use, this system or any of
its components. Raven Industries shall not be held responsible for any
modifications or repairs made outside our facilities, nor damages resulting from
inadequate maintenance of this system.

As with all wireless and satellite signals, several factors may affect the availability
and accuracy of wireless and satellite navigation and correction services (e.g.
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the
accuracy, integrity, continuity, or availability of these services and cannot
guarantee the ability to use Raven systems, or products used as components of
systems, which rely upon the reception of these signals or availability of these
services. Raven Industries accepts no responsibility for the use of any of these
signals or services for other than the stated purpose.

©Raven Industries, Inc. 2014

Table of Contents

Chapter 1 Important Safety Information................................................. 1

Electrical Safety ........................................................................................................................2

Chapter 2 Introduction............................................................................. 3

Preparing for Installation ...........................................................................................................4

Recommendations ..............................................................................................................4

Point of Reference ...............................................................................................................4

Updates .....................................................................................................................................4

Kit Contents ...............................................................................................................................5

Chapter 3 Mechanical Drive Installation ................................................ 9

Remove the Steering Wheel .....................................................................................................9

Install the Anti-Rotation Bracket ..............................................................................................11

Install the Spline and Ring Gear Assemblies ..........................................................................13

Reinstall the Steering Wheel ...................................................................................................14

Install the Mechanical Drive ....................................................................................................15

Chapter 4 Node and Wiring Installation............................................... 19

Install the SmarTrax MD Node ................................................................................................19

Node Mounting Locations ..................................................................................................19

Mount the SmarTrax MD Node ..........................................................................................20

Install the Foot Switch .............................................................................................................21

Install the Node Harness .........................................................................................................22

Install the Chassis Cable - SmarTrax MD-Only Systems (If Applicable) .................................23

Connect SmarTrax MD to an Existing Chassis Cable (If Applicable) ......................................24

Manual No. 016-5030-043 Rev. A i

Table of Contents

ii Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

CHAPTER

Chapt er 1

Important Safety

Information

1

NOTICE

Read this manual and the operation and safety inst ructions included with your implement and/or controller
carefully before installing the SmarTrax™ MD system.

• Follow all safety information presented within this manual.

• If you require assistance with any portion of the installation or service of your Raven equipment, contact

your local Raven dealer for support.

• Follow all safety labels affixed to the SmarTrax MD system components. Be sure to keep safety labels in

good condition and replace any missing or damag ed labels. To obtain replacements for missing or damaged
safety labels, contact your local Raven dealer.

When operating the machine after installing SmarTrax MD, observe the following safety measures:

• Be alert and aware of surroundings.

• Do not operate SmarTr ax MD or any agr icultural e quipment while unde r the influence o f alcohol or a n illegal

substance.

• Remain in the operator’s position in the machine at all times when SmarTrax MD is engag ed.

• Disable SmarTrax MD when exiting the operator’s seat and machine.

• Do not drive the machine with SmarTrax MD enabled on any public road.

• Determine and remain a safe working distance from other individuals. The operator is responsible for

disabling SmarTrax MD when the safe working distance has diminished.

• Ensure SmarTrax MD is disabled prior to starting any ma intenance work on SmarTrax MD or the machine.

WARNING

• The machine must remain stationary and switched off during SmarTrax MD installation or maintenance.

Manual No. 016-5030-043 Rev. A 1

Chapter 1

CAUTION

Electrical Safety

• Always verify that the power leads are connected to the correct polarity as marked. Reversing the power

leads could cause severe damage to the equipment.

• Ensure that the power cable is the last cable to be connect ed .

2 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

CHAPTER

Chapt er 2

Introduction

2

Congratulations on your purchase of the SmarTrax™ MD system!
SmarTrax MD-assisted steering takes the stress out of driving and makes it quick and easy for you to improve

your operating efficiency and performanc e. SmarTrax MD is compatible with Cruizer II™ and Cruizer II™ R TK,
Envizio Pro™, Envizio Pro®, Envizio Pro XL™, and Viper Pro™ systems.

The following instructions are designed to assist with the proper installation of the SmarTrax MD system. Refer
to the SmarTrax MD Calibration & Operation Manual (P/N 016-5030-020) for assistance with calibrating the
software and using the SmarTrax MD system.

This manual applies to the following machines:

MAKE: Fendt
MODEL: Vario 700 Series - 712, 714, 716, 718, 720, 722, and 724
Vario 800 Series - 818, 820, 822, 824, 826, and 828
Vario 900 Series - 924, 927, 930, 933, 936, and 939

FIGURE 1. Fendt Vario 828

Manual No. 016-5030-043 Rev. A 3

Chapter 2

Preparing for Installation

Before installing the SmarTrax MD system, park the machine where the ground is level, clean, and dry. Turn of f
the machine and leave it turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.

Recommendations

Raven Industries recommends the following best practices when installing or operating the SmarTrax MD
system for the first time, at the start of the season, or when moving the SmarTrax MD system to another
machine:

• Use part numbers to identify the parts.

• Do not remove the plastic wrap from a part until it is necessary for installation.

• Do not remove plastic caps from a part until it is necessary for installation.

Point of Reference

The instructions in this manual assume that you are standing behind the ma chine, looking toward the cab.

Updates

Software and manual updates are available on the Raven Applied Technology website:

http://www.ravenhelp.com

At Raven Industries, we strive to make your experience with our products as rewarding as
possible. One way to improve this experience is to provide us with feedback on this manual.

Your feedback will help shape the future of our product documentation and the overall service
we provide. We appreciate the opportunity to see ourselves as our customers see us and are
eager to gather ideas on how we have been helping or how we can do better.

To serve you best, please send an email with the following information to

[e-mail]

-Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

-Manual No. 016-5030-043 Rev. A

-Any comments or feedback (include chapter or page numbers if applicable).

-Let us know how long have you been using this or other Raven products.
We will not share your email or any information you provide with anyone else. Your feedback

is valued and extremely important to us.
Thank you for your time.

4 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

Introduction

Kit Contents

This section contains a list of the components that are included in the SmarTrax MD kit. Before beginning the
system installation, compare the items in the kit with the components on this list. If you have questions about
the kit, contact your Raven dealer.

TABLE 1. SmarTrax MD Installation Kit (P/N 117-5030-043)

Picture Item Description Part Number Qty.

Not Pictured

Manual - Fendt 700, 800, and 900 Series
SmarTrax MD Installation

Assembly - Ring Gear 063-4001-011 1

Assembly - Spline Adapter 063-4001-022 1

Trim - Ring Gear Protective 019-0159-590 1

Bracket - Node Mounting 107-0172-084 1

016-5030-043 1

Bracket - Angle Mounting 107-0172-270 1

Bracket - Collar Weldment 116-0159-751 1

Bearing - 1/2” Plastic Flanged 325-0000-036 1

Screw - #10-16 x 3/4” Zinc Self-Tapping 310-1002-073 4

Manual No. 016-5030-043 Rev. A 5

Chapter 2

TABLE 1. SmarTrax MD Installation Kit (P/N 117-5030-043)

Picture Item Description Part Number Qty.

Bolt - #10-24 x 3/4” UNC Zinc Carriage 311-0069-082 2

Bolt - 5/16”-18 x 3/4” Grade 2 Carriage 311-0069-111 2

Nut - 3/8”-16 Zinc Flanged Lock 312-1001-167 3

Nut - 5/16”-18 Zinc Flanged Lock 312-1001-184 2

Nut - #10-24 Wing 312-3000-013 2

Washer - 0.265” ID x 0.505” OD x 0.060”
Thick

Tape - 3” Double-Sided 332-0000-019 6

TABLE 2. SmarTrax MD Controller Kit (P/N 117-5030-020)

Picture Item Description Part Number Qty.

Not Pictured

Not Pictured

Manual - SmarTrax MD Calibration &
Operation

Sheet - Field Computer Minimum Software
Installation

313-2300-120 4

016-5030-020 1

016-5030-023 1

Assembly - SmarTrax MD Mechanical Drive
Unit

063-4001-010 1

6 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

TABLE 2. SmarTrax MD Controller Kit (P/N 117-5030-020)

Picture Item Description Part Number Qty.

Node - SmarTrax MD 063-4001-013 1

Pin - Anti-Rotation 107-4001-004 1

Cable - SmarTrax MD Node Harness 115-4001-157 1

Switch - Foot 063-0173-593 1

Introduction

Drive - USB Flash 063-4001-020 1

Manual No. 016-5030-043 Rev. A 7

Chapter 2

8 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

CHAPTER

Nut

Washer

Female Spline
Adapter

Bolts

Male Spline
Adapter

Chapt er 3

Mechanical Driv e

Installation

3

FIGURE 1. Spline Assembly Disassembled

1. Locate the 20 mm x 36 tooth spline adapter assembly (P/N 063-4001-022).

2. Disassemble the spine adapter assembly as shown in Figure 1 above.

Remove the Steering Wheel

Note: The steps in this section require use of a steering wheel puller ( not supplied) . For questio ns on the

proper procedure for removing the steering wheel, contact your local equipment dealer.

Manual No. 016-5030-043 Rev. A 9

Chapter 3

Steering Wheel Nut

FIGURE 2. Steering Wheel Cap

1. Remove the cap from the center of the steering wheel.

FIGURE 3. Machine’s Steering Wheel Nut

2. Remove the nut used to secure the steering wheel to the steering column.

FIGURE 4. Steering Wheel Removed

3. Using the steering wheel puller, remove the steering wheel from the steering column.

10 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

Install the Anti-Rotation Bracket

FIGURE 5. Steering Column Cover

1. Remove the control arm cover.

Note: Keep the control arm cover for future use.

Mechanical Drive Installation

FIGURE 6. Bolt Removal

2. Remove the bolts used to secure the control clamp to the steering column.

3. Remove the control clamp.

Note: Keep the control clamp for future use.

Manual No. 016-5030-043 Rev. A 11

Chapter 3

Collar Weldment
Bracket
(P/N 116-0159-738)

#10-24 x 3/4” UNC
Carriage Bolts
(P/N 311-0069-082)

1/2” Plastic
Flanged Bearing
(P/N 325-0000-036)

#10-24 Wing Nuts
(P/N 312-3000-013)

FIGURE 7. Anti-Rotation Bracket Installed

4. Clamp the collar weldment bracket (P/N 116-0159-751) around the steering column and secure it using the

machine’s bolts that were removed in step 2.

FIGURE 8. Flanged Bearing Installed on Bracket

5. Install the 1/2” plastic flanged bearing (P/N 325-0000-036) on the end of the collar weldment bracket using

two #10-24 x 3/4” carriage bolts (P/N 311-0069-082) and two #10-24 wing nuts (P/N 312-3000-013).

12 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

Mechanical Drive Installation

Female Spline
Installed

Machine’s Steering
Wheel Nut

Install the Spline and Ring Gear Assemblies

FIGURE 9. Female Spline Adapter Installed on Steering Column

1. Install the female spline adapter on the machine’s steering column stem.

2. Install the machine’s steering wheel nut th at was removed during the steering wheel removal.

FIGURE 10. Ring Gear Installed

3. Place the ring gear (P/N 063-4001-011) over the female spline adapter with the V-ring facing down and the

holes in the ring gear aligned with the holes in the spline adapter.

Manual No. 016-5030-043 Rev. A 13

Chapter 3

Steering Wheel
Spokes Aligned with
Ring Gear Assembly
Spokes

FIGURE 11. Male Spline Adapter Assembly Installed

4. Align the bolt holes in the male spline adapter with the holes in the ring gear assembly.

5. Install and tighten the spline assembly bolts to secure the male spline adapter and ring gear to the female

spline adapter.

Reinstall the Steering Wheel

FIGURE 12. Steering Wheel Placement

1. Align the spokes of the steering wheel with the spokes on the installed ring gear.

14 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

FIGURE 13. Washer and Nut Installed

Nut and Washer from
Spline Assembly
Installed

2. Install the steering wheel on the male spline adapter.

3. Reinstall the machine’s nut on the protruding male spline adapter.

FIGURE 14. Steering Wheel Cap Reinstalled

Mechanical Drive Installation

4. Replace the steering wheel cap.

Install the Mechanical Drive

Note: Depending on the machine’s configur ation, it may be necessary to install the an ti-rotation pin in th e

Manual No. 016-5030-043 Rev. A 15

mechanical drive’s casing af ter the mechanical drive is installed instead of before as indicated in
the instructions below.

Chapter 3

Anti-Rotation Brackets
Installed on Right Side of
Steering Column

Anti-Rotation Brackets
Installed on Left Side of
Steering Column

Anti-Rotation Pin Inserted
into Anti-Rotation Bracket
Assembly

FIGURE 15. Anti-Rotation Pin Installation Locations

1. Determine the anti-rotation pin (P/N 107-4001-004) installation location on the mechanical drive (P/N 063-

4001-010) based on the anti-rotation bracket installation location.

2. Screw the anti-rotation pin into the mechanical drive’s casing.

FIGURE 16. Anti-Rotation Pin Installed in Bracket Assembly

3. Insert the anti-rotation pin into the installed flanged bea ring (P/N 325-00 00-036) on the anti-rot ation bracket

assembly.

16 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

Mechanical Drive Installation

FIGURE 17. Mechanical Drive Installed

4. Install the mechanical drive around the insta lled ring gear assembly, closing it firmly until the latch on the

housing is securely locked.

5. Ensure the anti-rotation bracket assembly is installed securely.

Manual No. 016-5030-043 Rev. A 17

Chapter 3

18 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

CHAPTER

Direction Arrows

Any two arrows must
be parallel with level
ground

Mounting Tabs

1

2

3

4

5

Chapt er 4

Node and Wiring

Installation

4

Install the SmarTrax MD Node

Node Mounting Locations

FIGURE 1. Node Mounting

When choosing the location for the SmarTrax MD node, consider the following points:

• Mount the SmarTrax node inside the machine ’s cab on a flat, level surface for proper performance and

cable connection.

• One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle

travel, one arrow pointing straight up, and two of the arrows parallel to the ground.

Note: Make a note of the number of the arrow that is oriented in the direction of forward vehicle travel.

• The node mounting location must not create tripping hazards.

• Mount the node in a location where it will not be kicked or jarred during normal equipment operation.

• The location must allow cable routing to avoid crimping or damaging the cables or the node connections.

• Securely fasten the node using bolts or screws through at least two of the th re e mo u nt ing hole s. When

mounted properly, the node should not become loose or rotate.

Manual No. 016-5030-043 Rev. A 19

This number will be needed during the SmarTrax calibration process.

Chapter 4

Mount the SmarTrax MD Node

V ario 700 & 800 Series M ounting

FIGURE 2. Node Mounting Bracket Assembled

1. Secure the leg of the angle mounting bracket (P/N 1 07-0172-270) co ntaining the squar e holes to the front of

the node mounting bracket (P/N 107-0172-084) using two 5/16”-18 x 3/4” grade 2 carriage bolts (P/N 311­0069-111) and two 5/16”-18 zinc flanged lock nuts (P/N 312-1001-184).

FIGURE 3. Node Installed

Note: The forward vehicle direction is 3 in the pictured node orientation.

2. Place the node mounting bracket assembly against the cab wall next to the parking brake so that the angle

mounting bracket is flush with the cab floor.

3. Secure the angle mounting bracket to the floor using two #10-16 x 3/4” self-tapping screws (P/N 310-1002-

073).

4. Install the node (P/N 063-4001-013) on the mounting bracket assemb ly so that the node connectors point to

the front of the machine.

20 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

Node and Wiring Installation

5. Secure the node to the mounting bracket assembly using three 3/8”-16 flanged lock nuts (P/N 312-1001-

167).

Vario 900 Series Mounting

FIGURE 4. Node Installed

Note: The forward vehicle direction is 1 in the pictured node orientation.

1. Place the node mounting bracket (P/N 107-0172-084) on the floor of the cab to the left of the operator’s

seat, behind the parking brake.

2. Secure the bracket to the floor of the cab using four #10-16 x 3/4” self-tapping screws (P/N 310-1002-073)

and four 0.265” ID x 0.505” OD x 0.060” thick washers (P/N 313-2300-120) or six strips of double-sided
tape (P/N 332-0000-019).

3. Secure the node (P/N 063-4001-013) to the node mounting bracket using three 3/8”-16 zinc flanged lock

nuts (P/N 312-1001-167).

Install the Foot Switch

FIGURE 5. Foot Switch Installed

Manual No. 016-5030-043 Rev. A 21

Chapter 4

1. Select a suitable location for the foot switch (P/N 063-0173-593) to be installed.

Note: The foot switch should be installed in a location where the operator has easy access to it and is

able to fully press the pedal.

2. Using the holes in the foot switch as a template, drill holes in the floor of the cab.

3. Secure the foot switch to the floor by installing the supplied screws in each of the mounting holes.

Install the Node Harness

FIGURE 6. Node harness Connected to the Node

1. Install the two large, rectangular connectors of the node harness (P/N 115-4001-157) into the correct ports

of the node.

2. Tighten the bolts on the connectors to secure the connections.

3. Connect the female 4-pin Deutsch connector on the node harn ess to the foot switch cable connector.

4. Connect the node harness to the operator presence switch, if applicable.
a. Locate and disconnect the machine’s existing OPERATOR PRESENCE connection behind the

operator’s seat.

b. Connect the round 4-pin connector on the node harness to the machine’s mating OPERATOR

PRESENCE connector.

22 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

Node and Wiring Installation

FIGURE 7. Mechanical Drive Connection

5. Connect the 8-pin Deutsch connector on the node harne ss into the 8-pin port of the mechanical drive (P/N

063-4001-010).

6. Install the terminator (P/N 063-0172-369) supplied with the node harness on the remaining 4-pin Deutsch

connector.

Install the Chassis Cable - SmarTrax MD­Only Systems (If Applicable)

If the machine does not contain an existing chassis power system (such as AutoBoom, produ ct control, etc.), it
is necessary to install the chassis power cable to operate the SmarTrax MD system. If a CAN system already
exists on the machine, refer to Connect SmarTrax MD to an Existing Chassis Cable (If Applicable) below to
connect power to the SmarTrax MD system.

Note: The chassis cable is sold separately. Contact your local Raven dealer for ordering information.

1. Locate the SmarTrax chassis cable (P/N 115-4001-085).

2. Connect the TO SMARTRAX NODE connector from the chassis cable to the round 16-pin conne ctor on the

node harness (P/N 115-4001-157).

3. Connect the TO CONSOLE CABLE connector to the Raven console cable.

4. Install a terminator (P/N 063-0172-369) on the CAN cable connector.

5. Loop and tie-off the REMOTE SWITCH cable connection, securing it with plastic cable ties as necessary.

Note: The REMOTE SWITCH connector is not used in the SmarTrax system. Ensure the cable is

secured away from moving parts and heat sources.

6. Connect the ring terminals to the battery.

Note: The positive connectors are fused.

Manual No. 016-5030-043 Rev. A 23

Chapter 4

Connect SmarTrax MD to an Existing
Chassis Cable (If Applicable)

Note: The SmarTrax MD interface tee is sold separately. Contact your local Raven dealer for ordering

information.

1. Locate and disconnect the connection between the Raven console cable and chassis cable on the

machine’s existing CAN system.

2. Install the SmarTrax MD inter face tee cab le ( P/N 115-4001-070 or 115-4001-071) between the chassis and

Raven console harness.

3. Connect the SmarTrax node harness (P/N 115-4001-157) to the remaining SmarTrax MD interface tee.

24 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

I

Important Safety Information 1

Electrical Safety 2

Introduction 3

Kit Contents 5
Preparing for Installation 4

Point of Reference 4
Recommendations 4

Updates 4

K

Kit Contents 5

M

Mechanical Drive Installation 9

Installing the Mechanica l Dr ive 15
Installing the Spline and Ring Gear Assemblies 13
Reinstalling the Steering Wheel 14
Removing the Steering Wheel 9

N

Node and Wiring Installation

Connecting SmarTrax MD to an Existing Chassis

Cable 24

Installing the Chassis Cable - SmarTrax MD-Only

Systems 23
Installing the Foot Switch 21
Installing the Node Harness 22
Installing the SmarTrax MD Node 19

Mounting the SmarTrax MD Node 20
Node Mounting Locations 19

Index

Manual No. 016-5030-043 Rev. A 25

Index

26 Fendt Vario 700, 800, and 900 Series SmarTrax™ MD Installation Manual

Limited Warranty

What Does this Warranty Cover?

This warranty covers all defects in workmanship or materials in your
Raven Applied Technology Division product under normal use,

maintenance, and service when used for intended purpose.

How Long is the Coverage Period?

Raven Applied Technology products are covered by this warranty for 12
months from the date of retail sale. In no case will the Limited Warranty
period exceed 24 months from the date the product was issued by
Raven Industries Applied Technology Division. This warranty coverage

applies only to the original owner and is non-transferable.

How Can I Get Service?

Bring the defective part and proof of purchase to your Raven dealer.
If the dealer approves the warranty claim, the dealer will process the
claim and send it to Raven Industries for final approval. The freight cost
to Raven Industries will be the customer’s responsibility. The Return
Materials Authorization (RMA) number must appear on the box and all
documentation (including proof of purchase) must be included inside

the box to be sent to Raven Industries.

Upon confirmation of the warranty claim, Raven Industries will (at our
discretion) repair or replace the defective product and pay for the
standard return freight, regardless of the inbound shipping method.

Raven Industries will not assume any expense or liability for repairs
made outside our facilities without written consent. Raven Industries
is not responsible for damage to any associated equipment or
products and will not be liable for loss of profit, labor, or other
damages. The obligation of this warranty is in lieu of all other
warranties, expressed or implied, and no person or organization is

Damages caused by normal wear and tear, misuse, abuse,
neglect, accident, or improper installation and maintenance are

016-0171-537 Rev. A, E19889

What Will Raven Industries Do?

Expedited freight is available at the customer’s expense.

What is not Covered by this Warranty?

authorized to assume any liability for Raven Industries.

not covered by this warranty.

Extended Warranty

What Does this Warranty Cover?

This warranty covers all defects in workmanship or materials in your Raven Applied
Technology Division product under normal use, maintenance, and service when

used for intended purpose.

Do I Need to Register My Product to Qualify for the

Extended Warranty?

Yes. Products/systems must be registered within 30 days of retail sale to receive
coverage under the Extended Warranty. If the component does not have a serial

tag, the kit it came in must be registered instead.

Where Can I Register My Product for the Extended Warranty?

To register, go online to www.ravenhelp.com and select Product Registration.

How Long is the Extended Warranty Coverage Period?

Raven Applied Technology products that have been registered online are covered
for an additional 12 months beyond the Limited Warranty for a total coverage period
of 24 months from the date of retail sale. In no case will the Extended Warranty
period exceed 36 months from the date the product was issued by Raven Industries
Applied Technology Division. This Extended Warranty coverage applies only to the

original owner and is non-transferable.

How Can I Get Service?

Bring the defective part and proof of purchase to your Raven dealer. If the dealer
approves the warranty claim, the dealer will process the claim and send it to Raven
Industries for final approval. The freight cost to Raven Industries will be the
customer’s responsibility. The Return Materials Authorization (RMA) number must
appear on the box and all documentation (including proof of purchase) must be
included inside the box to be sent to Raven Industries. In addition, the words
“Extended Warranty” must appear on the box and all documentation if the failure is

between 12 and 24 months from the retail sale.

Upon confirmation of the product’s registration for the Extended Warranty and the
claim itself, Raven Industries will (at our discretion) repair or replace the defective
product and pay for the standard return freight, regardless of the inbound shipping

Raven Industries will not assume any expense or liability for repairs made outside
our facilities without written consent. Raven Industries is not responsible for
damage to any associated equipment or products and will not be liable for loss of
profit, labor, or other damages. Cables, hoses, software enhancements, and
remanufactured items are not covered by this Extended Warranty. The obligation of
this warranty is in lieu of all other warranties, expressed or implied, and no person

Damages caused by normal wear and tear, misuse, abuse, neglect, accident,

or improper installation and maintenance are not covered by this warranty.

016-0171-536 Rev. A, E19889

What Will Raven Industries Do?

method. Expedited freight is available at the customer’s expense.

What is Not Covered by the Extended Warranty?

or organization is authorized to assume any liability for Raven Industries.

Fendt Vario 700, 800, and 900 Series
SmarTrax™ MD Installation Manual
(P/N 016-5030-043 Rev A 02/14 E22761)

Raven Industries
Applied Technology Division Toll Free (U.S. and Canada): (800)-243-5435
P.O. Box 5107 or Outside the U.S. :1 605-575-0722
Sioux Falls, SD 57117-5107 Fax: [phone]
www.ravenprecision.com www.ravenhelp.com

Notice: This document and the information provided are the property of Raven Industries, Inc. and may only be used as
authorized by Raven Industries, Inc. All rights reserved under copyright laws.

©Raven Industries, Inc. 2014