Fender Stage100, Stage100H, Stage160 Operation Manual
ENGLISH - PAGES 4-5
READ ALL INSTRUCTIONS
BEFORE OPERATING UNIT!
ESPAÑOL - PÁGINAS 6-7
¡LÉANSE ANTES DE UTILIZAR EL APARATO Y
GUARDENSE PARA SU USO POSTERIOR!
FRANçAIS - PAGES 8-9
PRIERE DE LIRE AVANT L’EMPLOI ET A
CONSERVER POUR UTILISATION ULTERIEURE!
®
ITALIANO - PAGINE 10-11
LEGGERE ATTENTAMENTE PRIMA DELL’USO E
CONSERVARE PER UN UTILIZZO SUCCESSIV0!
DEUTSCH - SEITEN 12-13
BITTE VOR GEBRAUCH LESEN UND FÜR
SPÄTEREN GEBRAUCH AUFBEWAHREN!
- 14-15
2
• TO PREVENT DAMAGE, FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
• NO USER SERVICEABLE PA RTS INSIDE, REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
• THIS UNIT MUST BE EARTH GROUNDED.
• UNPLUG THE AC POWER LINE CORD BEFORE CLEANING THE UNIT’S COVERING WITH ONLY A DAMP
CLOTH; WAIT UNTIL THE UNIT IS COMPLETELY DRY
BEFORE RECONNECTING IT TO POWER.
ELÉCTRICAS, NO EXPONGA ESTA UNIDAD A LA LLUVIA
NI A LA HUMEDAD.
PUEDE REALIZAR EL USUARIO, SINO SÓLO
PERSONAL CUALIFICADO.
• NO MODIFIQUE EL ENCHUFE DE CA.
• E S TA UNIDAD DEBE CONECTARSE CON TOMA DE TIERRA.
• DESCONECTE EL CABLE DE ALIMENTACIÓN DE CA
ANTES DE LIMPIAR LA CUBIERTA DE LA UNIDAD; ESPERE
A QUE LA UNIDAD ESTÉ COMPLETAMENTE SECA ANTES
DE VOLVER A CONECTARLA A LA CORRIENTE.
UN DEPA RT D'INCENDIE, OU UN CHOC ELECTRIQUE,
NE L'EXPOSEZ JAMAIS A L'HUMIDITE OU A LA PLUIE.
POUR LES PIECES SITUEES DANS L'APPAREIL. LES
R E PA R ATIONS ET LA MAINTENANCE DOIVENT ETRE
EXECUTEES UNIQUEMENT PAR UN PERSONNEL
Q U A L I F I E .
• NE MODIFIEZ PAS LA PRISE DE CA.
• CET APPAREIL DOIT ETRE MIS A LA TERRE.
• DEBRANCHEZ LE CABLE D'ALIMENTATION AVANT DE
NETTOYER LE BOITIER DE L'APPAREIL ET AT T E N D E Z
QUE L'APPAREIL SOIT COMPLETEMENT SEC AVA N T
DE LE REBRANCHER SUR LE SECTEUR.
ELETTRICHE, NON ESPORRE QUESTA UNITÀ ALLA
PIOGGIA O ALL'UMIDITÀ.
FARE ESEGUIRE LA MANUTENZIONE SOLTANTO DA
PERSONALE QUALIFICAT O .
• NON ALTERARE LA PRESA C.A.
• Q U E S TA UNITÀ DEVE ESSERE COLLEGATA A TERRA.
• DISCONNETTERE IL CAVO DI ALIMENTAZIONE C.A.
PRIMA DI PULIRE LA COPERTURA DELL'UNITÀ; AT T E NDERE CHE L'UNITÀ SIA COMPLETAMENTE ASCIUTTA
PRIMA DI RICOLLEGARLA ALL'ALIMENTA Z I O N E .
FEUCHTIGKEIT AUS, UM BESCHÄDIGUNG, BRANDENTWICKLUNG UND ELEKTRISCHE SCHLÄGEN ZU VERMEIDEN.
UND REPERATUREN DÜRFEN NUR VON QUALIFIZIERT E N
TECHNIKERN DURCHGEFÜHRT WERDEN.
• MANIPULIEREN SIE AUF KEINEN FALL DIE NETZANS C H L U S S B U C H S E .
• DAS GERÄT MUSS GEERDET SEIN.
• STECKEN SIE DAS NETZKABEL AUS, BEVOR SIE DAS
GEHÄUSE DES GERÄTS REINIGEN. SCHLIESSEN SIE
DAS GERÄT ERST WIEDER ANS STROMNETZ AN,
WENN ES VOLLSTÄNDIG GETROCKNET IST.
3
FFeennddeer
r
SSttaaggee 110000 // 110000HH // 116600
FFrroonntt PPaanneell FFuunnccttiioonns
s
Congratulations on your purchase of a Fender
®
harmonically rich leads.
(100 watts @ 8 ohms).
to external effects devices or “add-on” ampli-
fiers.
• Balanced 3-pin XLR line out jack for connection to re c o rding or sound-re i n f o rc e m e n t
equipment.
• Classic Fender spring Reverb effect.
• Footswitch jack with channel and pre-amp
switching capabilities.
The operation and functions of all three versions
(Stage 100 and Stage 160 “amplifier/speaker
combinations” and the Stage 100H “amplifier
head only”) are identical except for the speaker
output functions (see items 3-5 under Rear
Panel Functions).
input for guitars with active pickups. Both
inputs are identical if used simultaneously.
N o rmal channel must be
selected for items 3-7 to function. See
CHANNEL SELECT (item 10).
loudness of the of the amplifier while in the
Normal channel.
the Normal channel.
Normal channel.
Normal channel.
the Normal channel.
• NOTE: The Drive channel must be selected
for items 8-9 and 11-16 to function. See
CHANNEL SELECT (item 10).
Red LED indicates MORE DRIVE boost is ON.
Yellow LED indicates MORE DRIVE boost is OFF.
See MORE DRIVE pre-amp boost (Item 12).
9. DRIVE - Adjusts the pre-amp level (distortion/sustain) of the Drive channel in conjunction with Drive channel VOLUME c o n t ro l
(item 11) to set the overall amplifier loudness.
10.CHANNEL SELECT - Button IN selects the
Drive channel. Button OUT selects the
Normal channel.
11.VOLUME (Drive channel)- Adjusts the amplifier loudness while in the Drive channel in
conjunction with the DRIVE control (item 9).
12.MORE DRIVE - Button IN activates the MORE
DRIVE pre-amp boost. This boost enhances
the intensity of the DRIVE control (item 9).
Button OUT deactivates MORE DRIVE boost.
13.TREBLE - Adjusts the high-frequency level of
the Drive channel.
14.MID - Adjusts the middle-frequency level of
the Drive channel.
15.BASS - Adjusts the low-frequency level of the
Drive channel.
16.REVERB - Adjusts the REVERB effect level of
the Drive channel.
17.POWER INDICATOR - Illuminates when the
amplifier is ON and receiving power.
8
91011
12
13
14 15 16 17
1 2
3 4 5 6 7
4
PART NUMBER: 22-6700 (120V, 60Hz) US 22-6800 (120V, 60Hz) US 22-6900 (120V, 60Hz) US
22-6730 (240V, 50Hz) Aust 22-6830 (240V, 50Hz) Aust 22-6930 (240V, 50Hz) Aust
22-6740 (230V, 50Hz) UK 22-6840 (230V, 50Hz) UK 22-6940 (230V, 50Hz) UK
22-6760 (230V, 50Hz) Eur 22-6860 (230V, 50Hz) Eur 22-6960 (230V, 50Hz) Eur
22-6770 (100V, 50/60Hz) Jpn 22-6870 (100V, 50/60Hz) Jpn 22-6970 (100V, 50/60Hz) Jpn
(WITH EXTENSION SPEAKER): 160W RMS into 4Ω @ 5%THD N/A 160W RMS into 4Ω @ 5%THD
620mV for 100W into 8Ω @1kHz N/A 620mV for 100W into 8 Ω @1kHz
2A250V for 230V / 240V ver 2A250V for 230V / 240V ver 2A250V for 230V / 240V ver
Normal/Drive, Drive/More Drive Normal/Drive, Drive/More Drive Normal/Drive, Drive/More Drive
SPEAKER COMPLIMENT: One 8Ω Celestion G12T-100 Two 8Ω Celestion G12T-100 N/A
12” speaker (P/N 054420) 12” speakers (P/N 054420)
WIDTH: 22.4 in. (57 cm) 26.1 in. (66 cm) 22.4 in. (57 cm)
DEPTH: 10.2 in. (26 cm) 10.3 in. (26 cm) 9.5 in. (24 cm)
Product specifications are subject to change without notice.
5
IEC grounding type supply cord to reduce the
possibility of shock hazard. Be sure to connect it
to a grounded AC receptacle in accordance with
the voltage and frequency ratings listed on the
rear panel under INPUT POWER.
Stage 100H.
put jack when only one8Ω speaker enclosure is to
be connected to the Stage 100H. If two 8Ω
speaker enclosures are to be connected, use both
parallel speaker output jacks (total load of 4Ω).
jack when o n e 4Ω speaker enclosure is to be connected to the Stage 100H. (Using this jack internally switches the Stage 100H to accept a 4Ω load.)
• NOTE: Item 5 applies only to the Stage 100.
5. EXTERNAL SPEAKER (8Ω minimum) - Use this
output jack when one 8Ω speaker enclosure is to
be connected to the Stage 100 for additional output. The Stage 100’s internal speaker must be
connected while using this jack.
6. LINE OUT - This balanced XLR line-level output is
designed for connection to an external power
amplifier or main house mixer. The signal from
this output jack includes all tone shaping done by
the amplifier.
7. RETURN - This 1/4 inch, unbalanced, TS, line-
level input jack is designed to accept a signal
from external effects devices or another amplifier
in a “daisy-chain” configuration.
8. SEND - This 1/4 inch, unbalanced, TS, line-level
output jack is designed to feed the preamp signal
to external effects devices or to an “add-on”
amplifier in a daisy-chain configuration.
9 . FOOTSWITCH - Connect the footswitch at this jack.
The two-button footswitch enables switching
between Normal and Drive channels and ON/OFF
switching of the MORE DRIVE p re-amplifier boost.
Using this jack disables these switching functions
f rom the front panel. NOTE: Connecting the
footswitch with an unshielded speaker type cord is
p referable to using a shielded coaxial guitar cord .
RReeaarr PPaanneell FFuunnccttiioonns
s
SSppeecciiffiiccaattiioonns
s
1
2
5
6 7 8
9
3 4
STAGE 100H
SPEAKER
JACKS
STAGE 100
SPEAKER
JACK
Stage 100 (combo) Stage 160 (combo) Stage 100H (head only)
Loading...