FENDA TECHNOLOGY PA922 User Manual

TM

PORTABLE 40-WATT BLUETOOTH

PARTY SPEAKER

Model: BWD19AAS10

PRODUCT GUIDE

Ver.01 Rev.01/22/18

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

R

plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your safety.
If the provided plug does not t into your outlet, consult an electrician for replacement of
the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the pointwhere they exit from the apparatus.

11. Only use attachment/accessories specied by the manufacturer.

12. Use only the cart, stand, tripod, bracket or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for
long periods of time

14. Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.

15. Power Sources - This product should be connected to a power supply only of the type
described in these operating instructions, or as marked on the unit.

1

16. Water and Moisture - This product should be kept away from direct contact with liquids. The
apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids,
such as vases, shall be placed on the apparatus.

17. CAUTION – Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type Batteries (a battery pack or an installed battery) shall not be exposes to
excessive heat such as sunshine, re, etc. .

18. Where the mains plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.

19. This symbol means the equipment is a Class II or double-insulated electrical
appliance. It has been designed in such a way that it does not require a safety
connection to electrical earth.

20. Do not install this equipment in a conned or "boxed-in" space such as a
bookcase or similar unit, and maintain good ventilation conditions. The ventilation
should not be impeded by covering the ventilation openings with items such as newspaper,
tablecloths, curtains, etc.

21. This apparatus is for professional use only.

22. When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable
tie). Be careful not to damage the power cord. Before using it again, make sure the power cord
has not been damaged. If the power cord has been damaged at all, bring the unit and cord to a
qualied service technician for repair or replacement as specied by the manufacturer.

23. WARNING: Please refer to any important information (e.g., electrical, safety, etc.) printed on
the exterior side enclosure before installing or operating the product.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or
moisture.The use of apparatus in moderate climates;No naked ame sources, such as lighted
candles, should be placed on the apparatus; Minimum distances 5cm around the apparatus
for sucient ventilation;To preserve our environment, dispose of used batteries according to
your local laws or regulations.

SERVICE INSTRUCTIONS

. Disconnect power cord before servicing.
. Replace critical components only with factory parts or recommended
equivalents
. For AC line powered units – Before returning repaired unit to user, use an ohmmeter to
measure from both AC plug blades to all exposed metal parts. The resistance should be
more than 2,000,000 ohms.

SAFETY NOTICES

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE ANY COVER. NO
USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
ONLY.

DANGEROUS VOLTAGE: triangle is intended to alert the user to the presence of
un-insulated "dangerous voltage" within the product's enclosure that may be of sucient
magnitude to constitute a risk of electric shock.

SA 1965

2 3 4 5 6 7

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

1. Lea estas instrucciones.

2. Conserve estas instrucciones.

3. Preste atención a las advertencias.

4. Siga todas las instrucciones.

5. No use este equipo cerca de agua.

6. Límpielo sólo con un paño seco.

7. No bloquee las aberturas de ventilación. Instale el equipo de acuerdo con las
instrucciones del fabricante.

8. No instale el equipo cerca de fuentes de calor tales como radiadores, aberturas de
entrada de calefacción, calefactores
u otros aparatos (incluidos amplicadores) que generen calor.

9. No anule la función de seguridad del enchufe tipo polarizado o con conexión a tierra. Un
enchufe polarizado tiene dos patillas, una más ancha que la otra. Un enchufe de tipo de
conexión a tierra tiene dos patillas y una clavija de puesta a tierra. La patilla ancha o la
tercera clavija son para su seguridad. Si el enchufe provisto no entra en su tomacorriente,
consulte a un electricista y solicítele el reemplazo del tomacorriente obsolete.

10. Proteja el cable de alimentación de modo que no lo pisen ni quede estrangulado,
particularmente en los enchufes, tomacorrientes y el punto donde sale del equipo.

11. Use sólo agregados y accesorios especicados por el fabricante. debe conectarse a un
tomacorriente del suministro eléctrico con una conexión a tierra de protección.

12. Use sólo el carrito, soporte, trípode, ménsula o mesa especicados por
el fabricante o vendidos con el equipo. Si usa un carrito, tenga cuidado al
mover la combinación de carrito/equipo para evitar que se vuelque y
produzca lesiones.

13. Desenchufe este equipo durante las tormentas eléctricas o cuando
no lo use por períodos prolongados.

14. Solicite todo servicio a personal de servicio calicado. Se requiere servicio cuando el
equipo se dañó de cualquier manera, por ejemplo si se dañaron el cable o el enchufe de
alimentación, si se derramó líquido o cayeron objetos dentro del equipo, si el mismo estuvo
expuesto a la lluvia o la humedad, si no funciona normalmente o se dejó caer.

15. Suministro eléctrico – Conecte este producto solamente a un suministro eléctrico del tipo
que se describe en estas instrucciones de operación o según se indique en la unidad.

16. Agua y humedad - Este producto se debe mantener fuera del contacto directo con los
líquidos. El aparato no debe ser expuesto al goteo o a la salpicadura y ningun objeto lleno de
líquidos, como serián los oreros, debe ser colocados cerca del aparato.

17. PRECAUCIÓN –Peligro de la explosión si la batería se substituye incorrectamente. Substituir
solamente por el mismo o el tipo equivalente. Las baterías (un bloque de baterías o una batería
instalada) no se deben exponer a calor excesivo, tal como la luz solar, el fuego, etc.

18. Cuando se usa el enchufe del suministro eléctrico o el acoplador de un artefacto como
dispositivo de desconexión, el mismo debe permanecer listo a operar.

19. Este símbolo signica que el equipo es un artefacto eléctrico Clase II o de doble
aislamiento. Está diseñado de manera tal que no requiere una conexión de seguridad
a la tierra eléctrica.

20. No instale este equipo en un espacio connado o "dentro de una caja" tal como una
biblioteca o una unidad similar, y mantenga buenas condiciones de iluminación. No debe
impedirse la ventilación cubriendo las aberturas correspondientes con elementos tales como
periódicos, manteles, cortinas, etc.

21. Este aparato es para uso profesional únicamente.

22. Cuando traslade o no use el artefacto, sujete el cable de alimentación (por ejemplo,
envuélvalo con un precinto). Tenga cuidado de no dañar el cable de alimentación. Antes de
usarlo nuevamente, asegúrese de que el cable de alimentación no esté dañado. Si dicho cable
presenta algún daño, lleve la unidad y el cable a un técnico de servicio calicado para
reparación o reemplazo según lo especique el fabricante.

23. ADVERTENCIA: Antes de instalar u operar el producto, consulte toda la
información importante (como la relativa a electricidad, seguridad, etc.) impresa
en la envuelta inferior exterior o el panel trasero.

ATTENTION : Pour réduire le risque du feu et du choc électrique, ne pas exposer cet appareil
aux pluies ou à l'humidité. L'usage de cet appareil sous un climat tempéré, défense de source
des ammes non protégée, parexemple, des bougies éclairées doivent être placées sur cet
appareil, 5cm de diatance au minimum autour de cet appareil pour la ventilation sussante;
pour protéger notre environnement, la disposition de batteries usées conformément à la loi
locale ou aux règlements.

LAS INSTRUCCIONES DE SERVICIO

. Desconecte el cable eléctrico antes de empezar el servicio.
. Substituya los componentes críticos solamente por las piezas de la fábrica o las
piezas equivalentes recomendadas.
. Para las unidades accionadas por CA - Antes de devolver la unidad reparada al utilizador,
utilice un ohmímetro para
medir entre las dos láminas del enchufe de CA y todas las partes expuestas. La resistencia
tiene que ser más de 2,000,000 ohms.

SEÑALES DE ADVERTENCIA

PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA NO QUITE NINGUN
TAPADERO. DENTRO DE LA UNIDAD NO HAY COMPONENTES ÚTILES PARA EL
UTILIZADOR. PARA EL SERVICIO SE DEBE DIRIGIRSE SOLAMENTE AL PERSONAL DE
SERVICIO CUALIFICADO.

SA 1965

VOLTAJE PELIGROSO NO AISLADO: La seña de relámpago con la punta de la echa
dentro del triángulo equilátero está puesto para alertar al utilizador de la presencia del
"voltaje peligroso no aislado" dentro del recinto de producto que puede tener la magnitud
suciente de correr un riesgo de descarga eléctrica.

Speaker Overview

5 6 7

1

2

3 4

8 9 10

1. Microphone/Guitar input

2. Aux input

3. Microphone/Guitar volume control

4. LED Display

5. Play/Pause

6. Previous (hold to seek FM station)

-TUNE/TRACK­HOLD FOR SEEK

/FM/AUX

11

12

7. Next (hold to seek FM station)

8. Power ON/OFF

9. Source(BT/AUX/FM)

10. Light mode

11. USB charging output

12. Master volume control

Package Contents

Main unit x 1
Power cable x 1
Product Guide x 1

Product Guide

8

Charging Bluetooth pairing

9

Insert the included power cable to charge
the unit. The charging icon will be on in
the display when charging.

Notes: The unit can be used with the
power cable while it simultaneously
charges the battery.
When four charging indicators light up,
indicates that the battery is fully charged.
When the red indictor ashes, it indicates
that the battery is low and needs to be
recharged.

Bluetooth

Bluetooth

Devices

Blackweb Party SPK

1. Hold to power on the product.

2. The Bluetooth icon in the display will start blinking rapidly.

3. Active the Bluetooth function on your device and search Bluetooth devices, and
select “Blackweb Party SPK” to start connecting.

4. Once paired, the Bluetooth icon in the display will turn on steadily, and you will
hear “Bluetooth Connected”.

5. Play music on your device paired and connected with the speaker.

During music play:
. Turn the right Master volume knob to adjust volume.
. Press to pause or resume music play.
. Press to skip to the previous/next song.

Notes: This speaker supports automatic connection with a previously paired
device after power-o and power-on again.
To pair with a new Bluetooth device or connect a previously paired device, rst
hold to disconnect the current Bluetooth device, and then repeat the above
step 3.

-TUNE/TRACK­HOLD FOR SEEK

/FM/AUX

AUX

Press to the AUX mode, then use a 3.5mm cable (not included)
to connect the speaker to another audio source.
Play and control music on your audio device, and use the volume
knob on the speaker to adjust volume if necessary.

Notes: In AUX mode, can’t be controlled.

AUX

10

11

1. Press to the FM mode.

2. A. Press repeatedly to tune to a
station step by step.
B. Hold to tune to a station
automatically.

3. Turn the right Master volume knob to
adjust volume.

To program FM radio station

1. Hold 2 seconds to search and
program available stations.

2. LED display will show the program
numbers such as: P_1 or P_2
…P_10(Max).

3. Tune to a station with , and
then press to assign above program
number to it. When successfully, the LED
display will show “SAVE”.

4. Short press to select the
corresponding station in your program
list.

Notes: The speaker will remember the
last station it was on and start at that
station when powered o and on again.

1. Connect your Microphone(not
included) or Guitar(not included)
to the MIC/Guitar socket.

2. Play Guitar through the speaker.

3. Sing along with the Microphone
when music played on
Bluetooth/Aux/FM mode.

4. Turn the MIC/GUITAR knob to
adjust the Microphone or Guitar
volume.

12

13

Connect your device’s charging cable
through the 5V 1A charging socket to
charge it. USB charging only functions
when the unit’s power if turned on.

Notes: To charge smartphones and tablets
faster, put the device’s screen to sleep.

1. Hold to turn on / turn o the light mode.

2. Short press repeatedly to select 5 available display modes.

1. Warning: Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

2. NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.

However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to

which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

3. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.

4. RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed
and operated with minimum distance between 20cm the radiator your body: Use only the
supplied antenna.
Product for Wal-Mart Stores, Inc. Bentonville, AR72716,Hotline [phone]

USER MANUAL INSERTS FOR FCC ID

.

1614 15