Fellowes Fortishred 4250C, Fortishred 4250S User Manual
FORTISHREDTM
4250C/4250S
Please read these instructions before use.
Do not discard: keep for future reference.
Veuillez lire ces instructions avant d’utiliser l’appareil.
Ne pas jeter : conserver afin de consulter les directives
ultérieurement, en cas de besoin.
Lea estas instrucciones antes del uso.
No las deseche: consérvelas como referencia futura.
Quality Office Products Since 1917
ENGLISH
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Models 4250C/4250S
A
.
B
.
C.
D.
E.
F.
CAPABILITIES
Will shred: Paper, credit cards, CD/DVDs, staples, paper clips and junk mail
Will not shred: Adhesive labels, transparencies, newspaper, cardboard, laminates, file
folders, X-rays or plastic other than noted above
Paper shred size:
Strip-Cut ...........................................................................................5/32 in. (4mm)
Cross-Cut ........................................................ 5/32 in. x 1-9/16 in. (4mm x 40mm)
G.
H.
KEY
A. Safety Shield
B. Paper entry
C. Disconnect switch (open door)
D. Door
E. Basket (inside)
F. Casters
H. Control Panel and LEDs
1. ON/OFF (blue)
R 2. Reverse (red)
3. Bin full (yellow)
4. Door open (red)
5. Safety Shield Open (red)
G. See safety instructions
Maximum:
Paper entry width .......................................................................... 12-1/5”(310mm)
8.5”x11”, 20lb., (75g) paper at 120V, 60 Hz, 8Amps; heavier paper, humidity or other than
rated voltage may reduce capacity.
* In order to perform at capacity, shredder must be plugged into a dedicated 15Amp,
120V outlet.
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
• Operation, maintenance, and service requirements are covered in the instruction
manual. Read the entire instruction manual before operating shredders.
• Keep away from children and pets. Keep hands away from paper entry. Always set
to off or unplug when not in use.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away from shredder
openings. If object enters top opening, switch to Reverse (R) to back out object.
• Never use aerosol products, petroleum based lubricants or other flammable
products on or near shredder. Do not use canned air on shredder.
• Do not use if damaged or defective. Do not disassemble shredder. Do not place
near or over heat source or water.
• Do not operate the machine without the safety shield closed (A)
• This shredder has a Disconnect Power Switch in the cabinet door. The door must
be fully closed to operate shredder. In case of emergency, open cabinet door. This
action will stop shredding immediately.
• Avoid touching exposed cutting blades under shredder head.
• Do not put foreign objects in paper entry.
• Shredder must be plugged into a properly grounded wall outlet or socket of the
voltage and amperage designated on the label. The grounded outlet or socket
must be installed near the equipment and easily accessible. Energy converters,
transformers, or extension cords should not be used with
this product.
• FIRE HAZARD – Do NOT shred greeting cards with sound chips or batteries.
• For indoor use only.
• Unplug shredder before cleaning or servicing.
BASIC SHREDDING OPERATIONBASIC SET UP
TO SHRED
1
Plug in and make
sure door is closed
2
Press ( ) ON to
activate
3
Feed paper straight
into paper entry and
release
4 5
or
When finished
shredding set to
( ) OFF
Do nothing and shredder
will automatically shut
off after 30 minutes of
inactivity
SHREDDER SET-UP
1
Open the door
2
Place cutter head into
top of cabinet, use 2
people
3
Ensure access to a
dedicated 15Amp,
120V outlet
4
Make sure safety flap
is securely in place
2
R
R
R
R
R
R
R
R
R
R
R
R
R
R
ADVANCED PRODUCT FEATURES
R
R
R
R
R
R
R
R
R
R
R
R
R
SilentShred™ Technology
SilentShred™ noise quality
shreds without noisy disruptions
SHEET CAPACITY SENSOR
Eliminates frustrating jams by preventing overloads.
Electronically measures paper thickness to prevent
paper jams:
Sheet Capacity Sensor
Helps prevent paper jams
by indicating sheet capacity
levels during the shredding
process
Up to RED: Too many sheets have been
inserted. Automatic reverse of paper.
Up to YELLOW: Maximum sheet capacity.
Safety Shield
Electronically controlled
shield stops shredder
when opened for
advanced safety
30
Auto Shut Off
After 30 minutes of
inactivity, shredder
automatically turns off for
zero energy consumption
R
Up to GREEN: Normal sheet capacity
during shredding process.
PRODUCT MAINTENANCE
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However,
on rare occasions the sensors may become blocked by paper dust causing the
motor to run even if there is no paper present (Note: two paper detection sensors are
located in the center of the paper entry).
TO CLEAN THE SENSORS
1
Turn off and unplug
shredder
2
Locate Auto-start
infared sensor
3
Use thin, long-handled brush
to clean sensors. Make sure
brush is clean and dry
4
Clean any contamination
from the paper sensors
TROUBLESHOOTING
OILING SHREDDER
All shredders require oil for peak performance. If not oiled, a machine may experience
diminished sheet capacity, intrusive noise when shredding and could ultimately stop
running. To avoid these problems, we recommend you oil your shredder each time you
empty your waste bin.
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
1
Set to Off (O)
2
*Apply oil
across entry
*Only use a non-aerosol vegetable oil in long nozzle
container such as Fellowes 35250
3
Set to Reverse (R) 2-3
seconds
Bin Full Indicator: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 3604101.
Safety Shield Indicator: When flashing alternatively with On/Off
Door Open Indicator: When flashing alternatively with On/Off
( )
LED, safety shield is open and shredding will stop. To resume shredding, make sure safety shield is closed.
( )
LED, safety shield is open. To resume shredding, make sure the door is closed.
Paper Capacity Indicator: When flashing blue, too much paper is inserted. Shredder will automatically stop and reverse paper. See Paper Jam section below.
Overheat Indicator: When flashing alternatively with On/Off
R
( )
LED, shredder requires a 10-15, minute cool down period. When
( )
is blue, resume shredding
PAPER JAM
3
If necessary, press
Reverse (R) to run
shredder in reverse and
then pull uncut paper
from shredder
Gently pull uncut paper
from paper entry
2
1
When flashing blue,
too much paper is
inserted. Shredder
will automatically stop
and reverse paper
4
Shred 1 sheet of
paper to clear
cutters. Resume
normal shredding
3
Loading...