MODEL S8PHMWM/850/DD/BZ
SECURITY HALF MOON LIGHT INSTALLATION INSTRUCTIONS
WARNING: These products may represent a possible shock or re hazard if improperly installed or attached in any way.
Products should be installed in accordance with the owners manual, current electrical codes and/or the current National
Electric Code (NEC).
PARTS INCLUDED
(1) Security half moon light
(1) Mounting bracket
(3) Wire nuts
CAUTION, IMPORTANT SAFETY INSTRUCTIONS -
same as the rated luminaire voltage. Do not install where marked operating temperatures
exceed the ignition temperature of the hazardous atmosphere. Do not operate in ambient
temperatures above those indicated on the luminaire nameplate. To avoid the risk of fire,
explosion, or electric shock, this product should be installed, inspected and maintained by a
qualified electrician only, in accordance with all applicable electrical codes. Be certain
electrical power is OFF before and during installation and maintenance.
Make sure the supply voltage is the
Note: Save these instructions for future reference.
For supply connections use wire rated for at least 90°C
CAUTION: Input 120VAC
8.7”
5”
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Note: This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
2.6”
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving antenna. Increase
the separation between the equipment and receiver. Connect the equipment
into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Any changes
or modications not expressly approved by the manufacture could void the
user's authority to operate the equipment.
LIMITED WARRANTY
This product is warranted to be free from
defects in workmanship and materials for up
to 5 years from date of purchase. If it fails to
do so, please contact Feit Electric at
info@feit.com or call 1-866 326-BULB (2852)
for instructions on replacement. Do not
return the product to the store.
For comments please write to:
Feit Electric
Customer Service Department
4901 Gregg Road, Pico Rivera, CA 90660
FEIT ELECTRIC COMPANY | PICO RIVERA, CA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
MODEL S8PHMWM/850/DD/BZ
WARNING: TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE
INSTALLING THE FIXTURE IN ORDER TO PREVENT POSSIBLE ELECTRIC SHOCK.
J-Box Mount Installation
1. Remove fixture from mounting bracket by
unscrewing the 2 side screws on the fixture
(Fig. A).
Fig A.
screws
3. Connect the power supply wires to the
fixture, ground to green, neutral to white
and hot to black. Feed wires into the
J-box (Fig C).
2. Make sure power is off. Feed power
supply wires through center mounting
bracket's hole. Install mounting bracket
onto the J-box (Fig B).
Fig B.
Mounting
bracket
4. Mount fixture and screws onto the
mounting bracket. Hand tighten the
screws with a screw driver. Caulk
between the fixture and the wall surface
with silicone sealant (not included). (Fig D).
J-box
Fig C.
FEIT ELECTRIC COMPANY | PICO RIVERA, CA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
Fig D.
Loading...