Feiss F2223-2 User Manual
ASSEMBLY INSTRUCTIONS FOR F2223/2
(E) 4/07
Canopy
(Fixture Plate)
Short
Threaded Pipe
Screws
Long
Threaded Pipe
Flat Washer
Canopy
(Fixture Plate)
Fixture Wire
& Ground Wire
Mounting Plate
Threaded
Chain Link
Chain
Threaded
Chain Link
Cap
Finial
Hex Nut
Lock Washer
Cover
Arm
Center Pipe
Bulb
(not included)
Socket Assembly
Pan
Glass Shade
Hex Nut
FIG. 1 CHAIN HUNG
INSTALLATION
Mounting Screws
Ball Cap Nut
Canopy Loop
Fixture Loop
Canopy
Threaded Pipe
Canopy Loop
Ball Cap Nut
TURN OFF THE POWER AT THE MAIN FUSE
IMPORTANT
OR CIRCUIT BREAKER BOX BEFORE STARTING INSTALLATION
Carefully unpack and identify all parts before assembly.
Bulbs are not included.
1. Thread fixture wires through center column. Install center column by
screwing onto top of socket assembly.
2. Install arms:
A. Take one arm and hook onto top section of center column. Make
certain arm is hooked onto a notch.
B. Then install bottom end of arm onto plate located at socket
assembly by fastening with a screw from the bottom.
C. Repeat others. Note: make certain top and bottom section of each
arm is aligned in correct angle.
3. Install a hex nut onto one end of long threaded pipe leaving about
3/8" (10 mm) thread exposed. Screw same end of threaded pipe into
bottom of socket assembly. Tighten hex nut.
4. This fixture can be mounted onto ceiling either aschain hung or flush
mount:
CHAIN HUNG INSTALLATION - Fig. 1:
A.Install a hex nut onto bottom end of short threaded pipe leaving
about 3/8" (10mm) of thread exposed. Slide short threaded pipe,
cover, and fixture loop through fixture wires. Screw the short
threaded pipe into coupler located at top of fixture. Tighten hex nut.
Then slip cover through the threaded pipe. Lock all together by
fastening the fixture loop onto protruding threaded pipe.
B.This fixture is supplied with 2 threaded chain links. These links
are opened and closed by twisting cylinder on chain link. One
threaded chain link should be installed onto canopy loop and the other
should be installed onto fixture loop. The standard chain should be
installed in between these 2 threaded chain links.
C.Determine the desired length of chain to hang. Remove any
unwanted links with chain plier.
D.Take ground wire and weave through above chain links, then
thread through center hole in canopy loop. Repeat with fixture wire
(wire with plastic insulation).
FLUSH MOUNT INSTALLATION - Fig. 2:
A. Remove and discard loop and threaded pipe from canopy by
loosening hex nut from above.
B.Install a hex nut onto bottom end of threaded pipe leaving about
3/8" (10mm) of thread exposed. Threaded fixture wires through the
threaded pipe, cover, and fixture plate. Install the threaded pipe by
screwing into coupler located at top of fixture. Tighten hex nut.
C. Slide cover and fixture plate, and install onto the threaded pipe by
fastening with lock washer and hex nut.
5. Cut excess wires leaving only 6" (15cm) length ofwires above
canopy. Split fixture wire into two strands. Then strip off 3/4" (19mm)
of outer plastic insulation.
6. Follow enclosed “Multiple Standard Installation Instructions” for
electrical and fixture installation onto ceiling outlet box.
NOTE: Before starting wire connection, enlist a helper to support the
fixture, or make a hook from a wire coat hanger and temporarily
suspend the fixture from mounting plate.
FIG. 2 FLUSH MOUNT
INSTALLATION
7. Install light bulbs (not included). See relamping label located near
socket area for type and maximun allowed wattage.
8. Sit decorative pan on top of glass shade. Then while holding securely
onto the glass shade, slide through the installed threaded pipe until
pan touches bottom end of arms. Secure into position by fastening
with a flat washer and hex nut. Afterward install finial by screwing
onto protruding threaded pipe.
Loading...