FEIMEX FX-500 User Manual

1

( 4 in 1)

USER MANUAL

LED BAR

2

1.BEFORE YOU BEGIN

What is included

Ø 1 x Fixture
Ø 1 x Power cable with plug
Ø 1 x User Manua

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton; check the
contents to ensure that all parts are present, and have been received in good
condition. Notify the shipper immediately and retain packing material for
inspection if any parts appear damaged from shipping or the carton itself shows
signs of mishandling. Save the carton and all packing materials. In the event that
a fixture must be returned to the factory, it is important that the fixture be returned
in the original factory box and packing.

AC POWER

This fixture has an auto-switching switch-mode power supply that can
accommodate a wide range of input voltages. The only thing necessary to do
before powering on the unit is to make sure the line voltage you are applying is
within the range of accepted voltages. This fixture will accommodate between
100V and 240V AC 50-60 Hz. Each light is connected end to end by the power
socket “POWER IN” and “POWER OUT” on the light, or use the waterproof power
cord. Please ensure the head and the tail tightening when connect the lights, to
prevent the power leakage occurred by water seepage to the plug.

Help preserve the environment! Ensure that this product is
recycled at the end of its life. Your supplier can give details

of local arrangements for the disposal of products.

3

Safety Instructions

!

WARNING!

Please read these instructions carefully, which includes

important information about the installation, usage and

maintenance of this product..

The following symbols are used to identify important safety information on the
product and in this manual:

!!

DANGER!
Safety hazard.
Risk of severe
injury or death

DANGER!
Hazardous
Voltage. Risk of
lethal or severe
electric shock.

WARNING!
Fire hazard

WARNING!
LED light
emission. Risk
of eye injury.

WARNING!
Refer to user

= This light belongs to grade I protection device, therefore the light must connect

to the earth excellently. And the power connection must be operated by the
professional technician.

= Make sure that the working voltage will not higher or lower than the rated value.
= Make sure that the cable didn't be damage or lacerated by sharp.
= The light must be power off when it's standing idle or before clearing.
= The cable must with plug, and you must pull out the cable by handle the plug.
= Please be careful when installing the lighting. Never touch the bared cable, or

it will cause the deadly electric shock.

= Please use the suitable and safe cable to connect the light.
= Please never remodel the light randomly, we will not take the guarantee for the

faulty and damage which caused by dismantle repair or remodel of the
nonprofessional person.

= Maximum ambient temperature 40°C. Do not operate fixture at temperatures

higher than this.

= Never connect the device to a dimmer pack.
= Do not daisy chain power to more than 8 units @ 120V and 12 units @ 230V.

4

2.INTRODUCTION

Specifications

l Voltage Rating: AC100V 240V 50-60Hz
l Power Rating: 110W
l LED Quantity: 15X4-in-1(RGBW)
l LED: 380mA
l Beam Angle: 20°/30° /40°(option)
l Ingress Protection: IP65 /indoor(option)
l Product Size: 990X120X145mm
l Package Size:1070X160X170 mm
l N/W:5.7Kg

Features

l RGBW color mixing with or without DMX controller
l special effect (minimum 16psc one group)
l 5 distinct dimming curves
l LED display with password protection
l Transfer custom programs between fixtures
l Operating Modes: DMX512 Connection /Master & Slave...

l DMX Channels: 11/04/06/15/17/21/60 channels

5

Product Overview

POWER IN

POWER IN

DMX IN

POOWER OUT

LED SIGNAL

LED SIGNAL

POWER OUT

DMX OUT

DMX OUT

DMX OUT

Dimensions

INDOOR

OUTDOOR

6

3.SETUP

Installation Requirement

l This product can be used in a variety of situations, can hang and put on

the ground.

l If hanging the fixture for over head use, then please follow the below steps.
l Please choose the suitable location to put or hang the light when installing it.

You must use the exclusive clamp hanger and screw when hanging it, and
make sure the weight of the light is within limits of the hanger.

l Please make sure without any flammable objects within 0.5m when

installing the light.

l The installation should be operated by professional person; any irregular

installation will cause the body injury or equipment damage.

l Block access below the work area and use suitable and stable platform

when installing or servicing fixture.

Hanging Clamp

Note: sold

separately

Safety Cable

Note: the cable must be
secured through the heat
sink ventilation
passageway.