Feig Electronic TSTPDFSAS User Manual

TST PD_FSAS

M

r

Multiturn Absolute Encoder w/ integrated

Wireless Safety System for industrial doors

– Stationary Unit

Mounting and Startup manual

!

ATTENTION

The content of the door controller manual and particularly the safety instructions
must get note!

2. Connection image inside with:

in terface cab le

coaxi al cabl e w ith

MC X conn ecto r

reset pi ns X3- 2

and X 3- 1

JST connector 8-pol e

Connector:

M12, 8-polig,
cable 0,4m 4x2x0.25

Encoder:

TST PDFSAS- 0.0-A

Antenna:

TST FSAS-0.1-A-circuit
board- Antenna with 0.9m long
coaxial cable

1. Pin connections:

1
2
3
4
5

6
7

8

GND

+24V
RS485 B
RS485 A

(not used)
safety e dge n o.

(safet y edge 2 optional)

breakaway

34
31
36

Controller

35

Si2

6

FU3P

TST

PDFSAS

weiß/white
braun/brown
grün/green
gelb/yellow
grau/grey
rosa/pink
blau/blue
rot/red

Remarks:

- For connection shielded cables with M12 A-encoded plug are recommended. The

shield has to be connected to earth ground only on the controller side.

- The housing of the plug is not allowed to be connected to earth ground.

- Not used wires must be isolated inside of FU3P

battery wi th co n ne ctor (see 2. 1)

2.1 battery change:

Attention

Disconnecting the battery effects clearing of position values from the
encoder! After reconnecting the battery a RESET must be done. Do not short
or charge the battery. Do not store or operate the system above the
specified temperature range. Connecting the encoder with switched on
supply voltage is not allowed.

) To do an Reset you must make an short cut between the Reset pins

X3-2 and X3-1 for a short moment

3. Mounting of encoder:

screw

magnet holder fixing

15.5 mm / 0.63 inch

17.5 mm / 0.69 inch

3 fo

...

- The assembling tolerance from shaft center to sensor center is

maximum +/-1 mm (+/- 0.039 inch).

- Torque for M3 screw / magnet holder fixing : maximum 0.4 Nm

magnet holder with magnet

24.5 mm / 0.965 inch ...

26.5 mm / 1.04 inch

engine shaft or gear box shaft
D = 12.0 mm + 0 mm / -0.1 mm
D = 0.49 inch + 0 inch / -0.004 inch

mounting plate

FEIG ELECTRONIC GmbH  Lange Str. 4  D-35781 Weilburg, Germany  Tel.: [phone] / 3109-0  Fax: [phone] / 3109-99  www.feig.de  Email:

[e-mail]

PD_FSAS_Eng_150409.Doc

4. Mounting of the stationary Antenna:

Side view Front view

Antenna

Mobile unit

Figure: Mounting of Antenna on door

5. Stationary Antenna + aluminum mounting bracket:

45

drill holes

5

0

1

39

7

4,2

8

4

Figure: Stationary Antenna + aluminum mounting bracket

Antenna

Mobi le uni t

alumin u m mo u n ti n g b racket

6

0

2

6. Technical Data:

Connection data: Supply voltage +24 V +/-10%, typical 50 mA.

Digital outputs: Three configurable outputs with the following standard setting:

Connecting to A-encoded M12 plug with 35cm long cable.

The max. allowed Length of the customer mounted cable is 50m

Radio : Operating range 2400 to 2483.5MHz

Temperature range: Operating range –40 to +70°C,

Protection class: IP65

Max. tolerable speed: 6000 U/min

Resolution: 13 Bit / turn (8192 Increments / turn)

Counter of turns: 15 Bit

Weight: Without cable but with magnet holder 220g

Lifetime of battery: typical 10 years

Dimensions (L x B x H): Encoder 92 x 69.5 x 24mm

Serial bidirectional Interface RS485 / 19,2k Baud

- Output 1 and 2: Safety output (N.O.) with 8.2kΩ terminal resistor

and testing of terminal resistor.

- Output 3: Breakaway output

(N.C. contact at 24V with 560Ω limiting resistor)

40 channels, Rated output power 0dBm

Storage range –40 to +70°C (recommended +20°C)

Antenna board 84 x 39 x 7.6mm (Antenna height 26mm)

7. FCC Statements:

1

2

0

Notice: This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

Notice: Changes or modifications made to this equipment not expressly approved by
FEIG ELECTRONIC may void the FCC authorization to operate this equipment.
Notice: This product has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and

24,5

6

,

7

44

used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or

5

1

television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures :

- Reorient or relocate the receiving antenna

- Increase the separation between the equipment and receiver

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

- Consult the dealer or an experienced radio / TV technician for help

FEIG ELECTRONIC GmbH  Lange Str. 4  D-35781 Weilburg, Germany  Tel.: [phone] / 3109-0  Fax: [phone] / 3109-99  www.feig.de  Email:

[e-mail]

PD_FSAS_Eng_150409.Doc