Fego Precision Co RF152 Users manual
Canopy
Antenna
SMART REMOTE
ACIN_N(WHITE)
ACIN_L(BLACK)
ON
SECURITY CODE
ON
LOW BATTERY
NOTICE
15.21- Any changes or modifications
not expressly approved by the
grantee of this device could void the
user's authority to operate the
equipment.
IMPORTANT SAFETY PRECAUTIONS
WARNING: To avoid electrical shock, be sure that
electricity has been turned off at the circ uit breaker or
fuse box before wiring
ALL wiring must be in accordance with the National
Electrical Code and local electrical codes. A qualified
electrician should perform electrical installation.
DO NOT use water or detergents to clean the remote
transmitting unit. A dry dust cloth will be suitable for
most cleaning.
ONLY the flip switch and transmitter unit should
change the fan s peeds.
Do not use the pull chain to change fan speeds after
installation, as damage could result to your remote
control or ceiling fan.
DO NOT use the reverse s witch when the ceiling fan
is operating. This could result in damage to your
Remotel control or ceiling fan.
INSTALLATION AND WIRING
WARNING: To avoid electrical shock, be sure that
Receiver
Bracket
Figure1.
electricity has been turned off at the circ uit breaker or
fuse box before wiring.
IMPORTANT: Follow these steps to insure proper
installation and operation
Install your ceiling fan by the wiring diagram provided
with the fan without the receiver in place.
Turn on electrical power at the circuit breaker or fus e
box. Turn wall switch‘’ON’’.
Set your ceiling fan to HIGH s peed with its pull chain
Control. Do not adjust the ceiling fan pull chain after this
Step.
Turn on light kit (if present)
Turn wall switch ‘’ OFF ‘’
Turn off electrical power at the circuit breaker or Fuse
box.
Connecting the Receiver
1. Disconnect the wires from the ceiling to the fan.
Install the rec eiver to the ceiling fan according to
your mounting type (Figure 1). Be sure the
antenna is positioned so it is exposed when
canopy is attached. Do not modify or damage the
antenna wire as control performanc e may be
reduc ed.
2. Use the two larger wire nuts supplied to connec t
the rec eiver and house wiring; then use the three
small wire nuts supplied to connect the receiver
and ceiling fan wiring. See Wiring Diagram in
Figure 2.
BLACK ‘’AC in L‘’ to HOT wire in ceiling
WHITE ‘’AC in N‘’ to NEUTRAL from ceiling
ANT ANTENNA
Figure 2.
WHITE (TO MOTOR N) to wire from fan.
BLACK (TO MOTOR L) to wire from fan
ORANGE (FOR UP LIGHT) to wire from fan.
BLUE (FOR DOWN LIGHT) to wire from fan.
PREFER: connect the ceiling to a power switch in
the power line to get the flip switch control
function.
3. Complete ceiling fan installation and assembly
according to its provided instruction.
IMPORTANT: When the frequency code is
changed a new c ode needs to be set by sliding
the FREOUENCY CODE SWITCH on the receiver.
TRANSMITTER OPERATION
SPEED BOTTON to set the fan speeds.
Light on/off: to toggle set the light on/off.
Dimmer: to set the light power rating. This key function
is only when the light is ON.And keep the light key.
PRESET FUNCTION (MEMORY):
If you use the wall switch to turn off the fan, the
speed and lighting level that you previously set will
remain in the remote control’s memory. The next time
electricity is turned on, fan operation will resume at the
same speed and lighting level when you press the FAN
and/or LIGHT key on the remote unit. NOTE For
convenient access and safe keeping of your remote
control unit. Mount near a wall switch by using the
bracket provided.
POWER RATING:
120V/60Hz
LIGHT: 300W MAX
FAN: 85W (MAX)
SWITCH
NOTICE
THE BATTERY OF THE REMOTE THAT USE THE ALKALINE BATTERY IS BETTER.
General information:
15.203 - The transmitter shall not be collocated
with other transmitters or antennas.
2.1091 & 2.1093 - To comply with FCC RF
exposure compliance requirements, a separation dis tance of at least 20 cm must be maintained between the antenna of this device and
all persons. This Transmitter must not be
collocated or operating in conjunction with any
other antenna or transmitter.
RF152-1
Loading...