Fego Precision Co BRC7000 Users manual

GALILEO

digital heater

MODEL BH3930

Read instructions before operating. Retain for future reference.

Instruction Leaflet

INFO-LINE

If after having read this leaflet, you have any

questions or comments on your heater,

call 1-800-253-2764 in North America.

☎

428-0771

MODEL BH3930 SHOWN

™

HEATER SAFETY

PLEASE READ AND SAVE
THESE IMPORTANT
SAFEGUARDS.

When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:

1. Read all instructions before using the appliance.

2. To avoid fire or shock hazard, plug the appliance directly
into a 120V AC electrical outlet.

3. The heater is hot when in use. To avoid burns, DO NOT
let bare skin touch hot surfaces. If provided, use handles
when moving this heater. Keep combustible materials, such
as furniture, pillows, bedding, papers, clothes, and curtains
at least 3 ft (0.9 m) from the front of the heater and keep
them away from the sides and rear.

4. DO NOT run cord under carpeting. DO NOT cover cord with
throw rugs, runners, or the like. Arrange cord away from traf­fic area and where it will not be tripped over.

5. This heater is not intended for use in bathrooms, laundry
areas and similar indoor location. NEVER locate heater where
it may fall into a bathtub or other water container.

6. Extreme caution is necessary when any heater is used by,
or near children or invalids, and whenever the heater is left
operating and unattended.

7. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the heater.

8. DO NOT operate heater with a damaged cord or plug,
or after the heater malfunctions, has been dropped or
damaged in any manner. Return appliance to manufacturer
for examination, electrical or mechanical adjustment, or
repair.

9. A heater has hot and arcing, or sparking, parts inside. DO
NOT use it in areas where gasoline, paint, or flammable liq­uids are used or stored.

1

10. Use appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by Bionaire

®

may

cause hazards.

11. DO NOT use outdoors.

12. To prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces,
like a bed, where openings may become blocked.

13. To disconnect heater, set controls to OFF, then remove
plug from outlet.

14. Avoid the use of an extension cord because the extension
cord may overheat and cause a risk of fire. However, if you
have to use an extension cord, the cord shall be No. 14
AWG minimum size and rated not less than 1875 watts.

15. Always unplug the heater when not in use.

16. Discontinue use if plug outlet is hot. We recommend

outlet be replaced if plug or outlet is hot to touch.

PLEASE SAVE THESE
INSTRUCTIONS.

CONSUMER SAFETY INFORMATION

To avoid an electrical circuit overload, do not operate another
high wattage product on the same circuit with the heater. This
appliance is equipped with a grounded type 3-wire cord (3-

prong plug). This type of plug
will only fit into an electrical
outlet made for a 3-prong plug.
This is a safety feature intended
to help reduce the risk of
electrical shock. If the plug
should fail to fit, contact a
qualified electrician to replace
the obsolete outlet.

DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
GROUNDED PLUG IN ANY WAY.

The length of the cord used on this product was selected
to reduce the hazards of becoming tangled in, or tripping

over a longer cord. If a longer cord is necessary an approved
extension cord may be used. The electrical rating of the
extension cord must be equal to or greater than the rating
of the heater. Care must be taken to arrange the extension
cord where it cannot be pulled on by children or accidentally
tripped over.

This device complies with Part15 of the FCC Rules.
Operation is subjected to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

AUTO SHUT-OFF

This heater is equipped with a patented, technologically­advanced safety system that requires the user to reset the
heater if there is a potential overheat situation. When a
potential overheat temperature is reached, the system will
automatically shut the heater off. It can only resume
operation when the user resets the unit.

To Reset the Heater:

1. Unplug the heater and wait 10 minutes for the unit to
cool down

2. After the 10 minutes, plug the unit in again and operate
normally.

HOW YOUR BIONAIRE

®

CONSOLE HEATER WORKS

Your Bionaire®heater uses natural convection heat to draw
cool air in and exhale warm air without the use of a fan.
Within this unit are heat-panel filaments that get warm in a
matter of seconds and hold their temperature evenly. The
air surrounding these filaments heats up, rises, and flows
out into the room. Cooler air is then drawn in to replace the
warm air and the process continues like a revolving door.
Because there is no fan, there is almost no noise.

PRE-OPERATING INSTRUCTIONS

1. Carefully remove your heater from the box (please save
the carton for off-season storage).

2. Place heater on firm level surface.

3. Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.

Note: The power light will remain lit during operation

2 3

ASSEMBLY INSTRUCTIONS
Wheel Assembly

Tools required for assembly: Phillips head screwdriver
Carefully unpack your Bionaire

®

heater from the box (it is
recommended to save the box for off-season storage).
You will find the following pieces:

1. Four casters (wheels) 2. Four screws 3. Two caster (wheel platforms)

WARNING DO NOT ATTEMPT TO OPERATE THE
HEATER WITHOUT THE WHEELS IN PLACE

1. Make sure the unit is unplugged. Using a slotted or Phillips

head screwdriver, attach two casters to each caster

platform.

2. Carefully turn the unit over
so the caster platforms can
be attached.

3. Slide the caster platform
into the bottom of the plas­tic end cap, following the
grooves (shown in Fig. 1).

4. Repeat this sequence on the other side of the heater, making
sure both sides are secure.

5. Return the console to its upright position.

FIRST USE ONLY:

1. Put batteries into Remote. The "Room" temperature is

displayed at all times. (Use 3 AAA Alkaline batteries
only, do not mix batteries)

2. Plug unit into outlet. The first time the unit is plugged

in, it will beep every two seconds until it is synced with
the remote. To sync unit with remote follow the below
steps:

Unlock remote. (This must be done before each use of
the remote) To Unlock remote, hold down the mode
button for 2 seconds until the lock symbol disappears
on the screen. Once the remote is unlocked, press the
mode button again and the unit will quickly beep 5
times telling the user the signal was received. DO NOT
SYNC more than 1 unit at once. A hazardous situation
may occur.

Note: If the batteries are running low on power, a low
battery indicator will appear on the remote. Low batteries
will affect transmission distance and the screen contrast.

We recommend replacing batteries immediately.
Note: The transmission distance for this remote is 30 ft,

do not use outside of 30 ft area of appliance. Remote
must be used in same room as appliance.

Note: Galileo can be used in either Fahrenheit or Celsius.
To change the reading on the remote, flip the remote over
and push the button located on the left hand side with a
ball point pen tip. This switch will change the reading from
F to C and vice versa.

Note: Every minute while in Auto mode, the Galileo com­munications with the base unit. If the Galileo goes out of
range and/or has low batteries, the communication will
stop, and after 8 minutes of non-communication the unit
wil shut off.

MANUAL OPERATION WITH REMOTE

1. Press Mode button on the remote. "Low" illuminates
on remote screen indicating mode. The power light
on the unit will turn on. The unit turns on and
operates in "Low" mode. The units "Low" light will
illuminate. In this mode, the unit will continuously run at
its low wattage.

4

Fig. 1

Caster

Platform

Casters

(Wheels)

X 4

Figure 2

Figure 3

5

mode

high

auto

low

(1000 Watts)

LOW

mode

HIGH
(1500 Watts)

AUTO

MODE

2. Press Mode button on remote a second time. The
remote screen will now display "High" (1500 Watts).
The unit’s "High" light will illuminate and the unit will
run in this mode. In this mode the unit will
continuously run at 1500 Watts.

Note: While using the remote, the backlight function will
turn on when any button is pushed and will turn off after
10 seconds of non-use.

Note: Do not cover remote while in use, this may affect
the accuracy of the temperature reading.

Note: Do not place remote under lamps as the radiant
heat from the lamp may affect the accuracy of the
thermostat.

Note: Because heat rises, and the Galileo remote senses
temperature, Bionaire recommends that you do not locate
the Galileo remote higher than 4ft from the ground. By
locating the Galileo more than 4 ft from the ground, you will
get a less accurate temperature reading than under normal
circumstances.

THERMOSTAT OPERATION WITH REMOTE

1. Press Mode button on remote until the remote screen
displays "Auto" and "low". The "Set" temperature is
displayed next to the "Room" temp. The "Auto" light
on unit will illuminate. The unit will cycle on and off to
main tain the "Set" temperature. The default room temp
= 72ºF. In this mode the unit will run to maintain the
"Set" temperature.

2. Press Mode button on remote again. The remote
screen displays "Auto" and "high". The "Set"
temperature is displayed next to the "Room" temp.
The "Auto" light on unit stays illuminated. The unit will
cycle on and off to maintain the "Set" temperature at
high wattage (1500 Watts).

3. To turn unit "Off", press the Mode button and the LCD
will go blank (except for the "Room" temperature
display which is always displayed while batteries are in
the remote) and the unit will shut off.

Note: It is normal for the heater to cycle on and off as it
maintains the preset temperature. To prevent the unit from
cycling, you need to raise the thermostat setting.

ADJUSTING SET TEMP:

1. When in "Auto" mode, press the (+) button on the
remote. The "Set" number will increase with each

press. Hold the button down to scroll. The minimum
temp is 55ºF and the maximum is 85ºF. The unit scrolls
one digit at a time in a continuous loop. 55º, 56º…, 84º,
85º, 55º, 56º….

2. When in "Auto" mode, press the (-) button on the
remote to decrease the "Set" temperature. The
unit scrolls one digit at a time in a continuous loop.

UNIT OPERATION WITHOUT REMOTE

A. Remote and Unit are OFF:

1. Press the Mode button on the unit the first time. The
"Low" light illuminates and the unit runs in "Low" mode.
The power light turns on.

2. Press the Mode button a second time to run in "High"
mode (1500 Watts).

3. Press the Mode button a third time and the unit shuts
off.

Note: The "auto" light only illuminates when the unit is set
to "auto" mode by the remote.

B. Remote is ON and Unit is ON:

1. Press the Mode button on the unit. The unit will then
switch "Modes"; either from "Low" to "High", "High" to
"Off" or "Auto" to "Off" . The unit’s lights will reflect the
change. The Remote will display a different mode – the
mode in which it was left. If a button is pressed on the
Remote, the Remote’s signal will override the "Mode"
on the unit and the two will be back in sync.

TIMER FUNCTION:

To turn unit off while remote and unit are on (in low, high,
auto state).

1) Hold mode button for 2 seconds to unlock remote.

2) Push + and - together.

2.1) "timer" turns on. 1 Hr appears on the screen.

2.2) the current mode will remain displayed on the
screen ("low" or "high" or "auto")

3) Push + or - to adjust the number of hours the unit will
run before it shuts itself off.

3.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8 hours

3.2) 1 through 8 will scroll in a continuous loop

4) After you have made your selection, "timer" flashes for
5 seconds after last button push of + or - then goes

6

7

back to previous mode

4.1) "timer" remains lit to show the timer function has
been set.

5) At any time if you unlock the remote and push the
mode button to turn the unit off the timer setting
will be erased and "timer" will disappear from the
remote. To check how much time is remaining, press
and hold the + and – buttons simultaneously.

5.1) To turn unit on while remote and unit are off (only
ambient temp is displayed on remote).

This function is meant for a person to preheat a room by
setting the timer. For Example: Locating the unit in the
bedroom and setting the timer at 8AM for 12hrs, this
allows the room to preheat for 2 hours. The unit will turn
on at 8PM and shut off at 10PM. Your room will be pre­heated before you go to bed at 10PM.

1) Hold mode button for 2 seconds to unlock remote.

2) DO NOT push mode again as this will turn unit on.

3) Push + and - together.

3.1) Unit remains off.

3.2) "timer" and "auto - high" turns on and flashes on
the remote, and 1 Hr appears on the screen

4) Push + or - to adjust the number of hours that will pass
before it turns itself on.

4.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
11, 12, 13, 14, 15, 16 hours

4.2) 1 through 16 will scroll in a continuous loop

5) "timer" flashed for 5 seconds after last button push of +
or - then goes back to previous mode

5.1) "timer" and "auto - high" remain lit to show the
timer function has been set.

5.2) The timer will turn the unit on and run for 2 hrs
then shut off and maintain the room in auto - high at
the default of 72 degrees F. After these 2 hours, the
unit will shut off.

6) At any time if you unlock the remote and push the
mode button on the remote the timer setting will be
erased and "timer" will disappear from the screen.

CLEANING/MAINTENANCE
During Season Care:

1. Always unplug the heater before cleaning

2. Clean the unit with a soft cloth moistened with a mild
soap solution.

3. NEVER use abrasive or flammable solvents to clean
the unit.

4. After cleaning, be sure to completely dry the unit with a
cloth or towel.

☛

TIP: Over time, dust may accumulate on the grills. This
can be removed by wiping the unit with a damp cloth.
Always unplug unit and allow to cool prior to cleaning.

After Season Care:

1. Store heater in a cool, dry location.

2. Bionaire®recommends that you store the unit in its
original carton.

TROUBLESHOOTING
If your heater fails to operate:

• UNPLUG THE UNIT

• Make sure the electrical outlet or circuit breaker is
working.

• Check for obstructions. If you find an obstruction turn
the heater OFF, and unplug the unit. Carefully remove
the obstruction and follow the reset instructions.

• The temperature may be set too low. Adjust the
thermostat until the heater restarts.

Please DO NOT attempt to open or repair the heater.
Please see the Warranty for Service Instructions.

HEATER SERVICE INSTRUCTIONS

1. Do NOT attempt to repair or adjust any electrical or

mechanical functions on this unit. Doing so will void the
warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed by
qualified personnel only.

2. If you need to exchange the unit, please return it in its

original carton, with a sales receipt, to the store where
you purchased it. If you are returning the unit more than
30 days after the date of purchase, please see the
enclosed warranty.

3. For service information please call

1-800-253-2764 or

visit our website at www.bionaire.com.

4. ✉If you have any other questions or commentor

feel free to write to us:

8

9

The Holmes Group, Inc.
Consumer Service Department
32B Spur Drive
El Paso, TX 79906

Canada
6385 Shawson Drive
Mississaugua, Ontario
Canada, L5T IS7

WARRANTY

Operation under conditions other than those recommended
or at voltages other than the voltage indicated on the unit,
or any attempts by unauthorized personnel to service the
unit or modify it, will render the guarantee void.

Bionaire®shall not be liable for any personal injury, property
damage or any incidental or consequential damages of any
kind (including water damage), resulting from defects,
malfunctions, misuse, improper installation or alteration of
the product.

BIONAIRE®EXPRESSLY DISCLAIMS ALL
RESPONSIBILITY FOR CONSEQUENTIAL
DAMAGES OR INCIDENTAL LOSSES
CAUSED BY USE OF THIS PRODUCT.

The provisions of this warranty are in addition to, and not a
modification of, or subtraction from the statutory warranties
and other rights and remedies contained in any applicable
legislation and to the extent that any such provision
purports to disclaim, exclude or limit any such statutory
warranties or other rights or remedies, such provisions
shall be deemed to be amended to the extent necessary
to comply therewith.

For Warranty Service, please call 1-800-253-2764
in North America.

A Bionaire®consumer service representative will help
determine which is the best procedure in order for your
heater to be repaired.

KEEP THIS NUMBER FOR FUTURE REFERENCE.

Galileo™ is a trademark of The Holmes Group, Inc.
Bionaire® and Bionaire

®

are registered trademarks of

The Holmes Group, Inc.

10

The Fego Precision Industrial Co., Ltd. Model: 3430TX;3930TX (referred to as the EUT in this report)

is a wireless transmitter of Heater Fan Remote Control.
A major technical descriptions of EUT is described as following:

A). Fundamental Frequency: 315 MHz

B). Modulation : Pulse Modulation

C). Antenna Designation: Non-User Replaceable (Fixed)

D). Power Supply: DC 4.5V, Battery Operated.

E). Transmitting Time: Periodic < 5 seconds by manual

F) Associated Receiver: FCC Doc

FCC Statement

of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
installed and used in accordance with the instructions, may cause harmful interference in to radiate

communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this

This device complies with part 15 of the FCC Rules. Operation is subject to the following two condition.(1).this
device may not cause harmful interference. (2).this device must accept any interference received, including
interference that may cause undesired operation

Warning:

Note: This equipment has been tested and found to comply with the limits for digital device, pursuant to Part 15
residential installation. This equipment generates, used and can radiate radio frequency energy and, if not

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

l Reorient or relocate the receiving antenna

l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different form that to which the receiver in connected.
l Consult the dealer or an experienced radio/TV technician for help.

equipment. Such modification could void the user ’s authority to operate the equipment.