Federal Signal Corporation VIEWPOINT FVPK Installation Instructions Manual
INSTALLATION INSTRUCTIONS
FOR
MODEL FVPK PERMANENT MOUNTING KIT
ON
VIEWPOINT™ LIGHT ASSEMBLY
2561048B
REV. B 195
Printed in U.S.A.
SAFETY MESSAGE TO INSTALLERS
People’s lives depend on your safe installation of
our products. It is important to read, understand and
follow all instructions shipped with the products. In
addition, listed below are some other important
safety instructions and precautions you should
follow:
• To properly install mounting kit, you must
have a good understanding of emergency
vehicle procedures and systems.
• When drilling into a vehicle structure, be
sure that both sides of the surface are clear
of anything that could be damaged.
• Refer to installation instructions packed with
light assembly for proper electrical installation and precautions.
• You should frequently inspect the light
system to ensure that it is operating properly
and that it is securely attached to the vehicle.
• File these instructions in a safe place and
refer to them when maintaining and/or reinstalling the product.
Failure to follow all safety precautions and
instructions may result in property damage, serious
injury, or death to you or others.
A. UNPACKING.
C. INSTALLATION OF MOUNTING BRACKET TO
LIGHT.
1. Carefully turn one of the ViewPoint halves
upside down and place it on a surface which will not
scratch the domes.
NOTE
Step C.2. requires the use of the 3/8-16 nuts
and 3/8" flat washers saved during unpacking.
2. Assemble the appropriate pair of mounting
brackets on the carriage bolts (factory installed)
using nuts, flat washers, and lockwashers as shown
in figure 1. Position the brackets adjacent to the
inboard and outboard pods allowing access to the
holes used to mount the light assembly on the vehicle
roof. Secure the brackets in position.
3. Repeat steps C.1. and C.2. on the other
ViewPoint half.
D. INSTALLATION ON VEHICLE ROOF.
1. See figure 2. Position one ViewPoint half on
the vehicle roof at the desired location. The unit
should be positioned with the pods aligned facing
forward. In addition, ensure that the unit does not
interfere with operation of other apparatus.
2. Using the mounting brackets as templates,
scribe four drill position marks on the mounting
surface.
After unpacking the mounting kit, carefully
check all envelopes, shipping labels, and tags before
removing or destroying them. Ensure that the parts
listed in the KIT CONTENTS LIST are contained in
the packing carton.
B. KIT CONTENTS LIST.
Qty. Description Part Number
8 Screw, 1/4" x 3/4", Type B, 7011A158-12
Thd. Forming
16 Pad, Mounting, Rubber 8422A033
2 Bracket, Permanent, Left 8572280
2 Bracket, Permanent, Right 8572281
4 Nut, Hex, 3/8-16, S.S. 7059A063
4 Washer, 3/8, S.S. 7072A035
8 Lockwasher, Split, 3/8, S.S. 7074A046
Figure 1.
3. See figure 2. Position the other ViewPoint
half on the vehicle roof. Using the mounting brackets
as templates, scribe four drill position marks on the
mounting surface.
CAUTION
Avoid damage to electrical wiring and other
parts of vehicle. When drilling or cutting on
ANY part of the vehicle, ensure that both sides
of the surface are clear of parts that could be
damaged.
Also, when drilling mounting holes, ensure
that holes are drilled only through sheet metal
and not through upholstery.
4. Prior to drilling, move the units out of the
way. Drill eight 0.199" (#8 drill) diameter holes at the
previously scribed drill position marks.
5. Place the light assembly halves in position on
the roof. Insert two mounting pads between the light
assembly halves and roof for each mounting bracket
leg (see figure 3). Secure the light assembly halves to
the roof using eight 1/4" x 3/4" thread-forming screws
and tighten securely. The ViewPoint should now be
solidly anchored to the roof.
6. Ensure that all fasteners are properly tightened.
Figure 3.
Figure 2.
Loading...