Federal Signal Corporation DTX Series, DTX-UNI Installation Instructions Manual

Installation Instructions for the Model DTX-UNI
Universal Mount for the Model DTX-RC Rear Camera

2562586A REV. A 1010

Safety Messages to Installers of Federal Signal Products

People’s lives depend on your proper installation and servicing of our products. It is important to
read and follow all instructions shipped with this product. In addition, listed below are some other
important safety instructions and precautions you should follow:

• To properly install a vehicular camera system and the options, you must have a good

understanding of automotive electrical systems along with proficiency in the installation and
use of safety warning equipment.

• Read and follow all safety and operating instructions before installing, conguring, or
operating the entire DTX Series system. Safety and operating instructions are also located
in the DTX Series software interface and can be accessed by clicking the Help button.

• DO NOT install equipment or route wiring in the deployment path of an airbag.

• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the seat

needs to be recalibrated for proper airbag deployment.

• When drilling into a vehicle structure, be sure that both sides of the surface are clear of
anything that could be damaged. Remove all burrs from drilled holes. To prevent electrical

shorts, grommet all drilled holes through which wiring passes. Also ensure that the mounting
screws do not cause electrical or mechanical damage to the vehicle.

• You should frequently inspect the DTX Series System to ensure that it is operating properly

and that it is securely attached the vehicle.

• File these instructions in a safe place and refer to them when maintaining or reinstalling the

product.

Failure to follow all safety precautions and instructions may result in property damage, serious

injury, or death.

Product Overview

The Model DTX-UNI Universal Mount (FSC Part No. 8605205) is a mounting option for the
Model DTX-RC Rear Camera. The DTX-UNI is ideal for applications requiring a greater viewing
range than that available with the standard camera mounting bracket. The dual gimbal mounts

provide universal viewports while balancing the weight of the camera from above rather than

from below, xing the camera in a highly stable position. The DTX-UNI is preassembled to make
attaching the rear camera quick and easy, and comes with an Allen key to aid in the installation.

Required Tools

• Drill and drill bit suitable for the material and type of screw used (machine or Type A)

• Screwdriver for installer-supplied #10 screws

• Allen key supplied with the DTX-UNI

DTX Series Installation Instructions

Universal Mount

UNIVERSITY PARK

FEDERAL SIGNAL

CORPORATION

#805205A

DTX Series Rear Cam

290A6590

*

KNOB FOR ADJUSTING

CAMERA ANGLE: LOOSEN

TO REMOVE MOUNTING FLANGE

*

PANORAMIC ROTATION

FRONT TILT

LATERAL TILT

*

SIDE ARM FOR
ADJUSTING
CAMERA ANGLE

MOUNTING HEAD

CAMERA BRACKET

MOUNTING FLANGE:

CHOOSE THREE HOLES

FOR BEST STABILITY

HEX-HEAD SCREWS, LOCKWASHERS,
AND WASHERS (3 PER SIDE)
SECURING CAMERA: LOOSEN,
ADJUST TILT, THEN TIGHTEN

DTX-RC REAR CAMERA

LIGHT SHIELD (OPTIONAL)

THREE PHILLIPS SCREWS AND

TOOTHED LOCKWASHERS SECURING

DTX-UNI BRACKET TO MOUNTING HEAD

Required Hardware

• Three #10 installer-supplied screws
(type dependent on thickness and material composition of mounting surface

Figure 1 DTX-UNI Universal Mount

Installing the DTX-UNI Universal Mount

To install the DTX-UNI Universal Mount in the vehicle:

Step 1: Locate a fixed, rigid mounting surface that provides a wide viewing range toward the

rear of the vehicle.

Step 2: Remove the circular mounting ange from the assembly by loosening the knob

(Figure 1).

Step 3: Use the ange as a template to mark three holes for securely attaching the universal

mount and camera assembly (Figure 2 on page 3). Ensure that no devices and wires

behind the panel are damaged when you drill through the mounting surface.

Step 4: Select a drill-bit size appropriate to the screw type and surface material you are using

to mount the DTX-UNI. Drill the three mounting holes.

Step 5: Secure the ange on the mounting surface with the three installer-supplied #10 screws.

2

Model DTX-UNI Rear Camera Universal Mount

DTX Series Installation Instructions

Ø 1.860"

Ø 1.920"

Ø 2.440"

Ø 0.220"

290A6587

Figure 2 DTX-UNI mounting ange

Attaching the Camera to the DTX-UNI Universal Mount

To attach the rear camera to the universal mount:

Step 1: Remove the standard mounting bracket from the Model DTX-RC camera by using the

Allen key to remove the six socket screws, lockwashers, and washers securing it to the
camera (Figure 1 on page 2).

Step 2: Attach the camera (with the light shield, if required) to the DTX-UNI mounting bracket

with the mounting hardware removed in step 1: three screws, lockwashers, and

washers per side.

Step 3: Re-attach the universal mount assembly to the ange and tighten the knob.

Step 4: Pivot the camera to the selected viewpoint by loosening the knob and side arm locking

the gimbal joints. Tighten the knobs to ensure the assembly remains stable during
everyday use (Figure 1).

Step 5: To aim the camera in the bracket, loosen the six socket screws, tilt the camera, then

tighten the screws.

Connecting the Camera Cable

To connect the camera to the DTX system:

Step 1: Route and connect the 17-foot video cable of the DTX-RC camera to the black

connector of the DTX-CC peripherals cable from the DTX-2-DVR. Ensure that the

cables do not interfere with the operation of any equipment or hinder the activities of
the driver and passenger.

Step 2: Test the connection to the DTX-2-DVR to ensure the camera cable connection is

working properly.

Model DTX-UNI Rear Camera Universal Mount

3

DTX Series Installation Instructions

Obtaining Technical Support and Service

If a DTX Series system device does not operate properly and falls within the warranty coverage

provided, or if servicing assistance is needed, contact technical support at:

Federal Signal Corporation
2645 Federal Signal Drive
University Park, IL 60484-3167
Phone: [phone]

[e-mail]

Returning a Product to Federal Signal

Before returning a product to Federal Signal, call 800-264-3578, 800-433-9132, or 800-824­0254 to obtain a Returned Merchandise Authorization number (RMA number). To expedite the

process please be prepared with the following information:

• Your Federal Signal customer or account number.

• The purchase order number under which the items were purchased.

• The shipping method.

• The model or part number of the product being returned.

• The quantity of products being returned.

• Drop ship information as needed.

• Any estimate required.

When you receive your RMA Number:

• Write the RMA number on the outside of the box of returned items.

• Reference the RMA number on your paperwork inside of the box.

• Write the RMA number down, so that you can easily check on status of the returned

equipment.

Send all material with the issued RMA Number to:

Federal Signal Corporation
Public Safety Systems
2645 Federal Signal Drive
University Park, IL 60484-3167
Attn: Service Department
RMA: #__________
800-433-9132
800-343-9706 (fax)

www.fedsig.com

4

© 2010 Federal Signal Corporation

Model DTX-UNI Rear Camera Universal Mount