Federal Industries SQRIC45SS Installation Manual

SQROC90SS, SQROC45SSR

SQRIC91SS, SQRIC45SS

Self-Contained & Remote Models

INSTALLATION & OPERATION

INSTRUCTIONS

KEEP THIS MANUAL FOR FUTURE REFERENCE

Engineering and technical data are subject to change without notice.

Federal Industries P.O. Box 290 Belleville, WI 53508
Toll Free 1(800) 356-4206 WI Phone [phone] Fax: [phone]

INTRODUCTION

Thank you for purchasing a Federal Industries display case. This manual contains important
instructions for installing and servicing the Market Deli Refrigerated Cases. A repair parts list and
wiring diagram are also included in the manual. Read all of these documents carefully before
installing or servicing your case.

NOTICE

Read this manual before installing your case. Keep this manual and refer to it before doing any service
on the equipment. Failure to do so could result in personal injury or damage to the case.

NOTICE

Installation and service of the electrical components in the case must be performed by a licensed
electrician.

The portions of this manual covering electrical components contain technical instructions intended only for
persons qualified to perform electrical work.

DANGER

Improper or faulty hookup of electrical components in the case can result in severe injury or death.
All electrical wiring hookups must be done in accordance with all applicable local, regional, or national

standards.

SERIAL NUMBER

Record the model and serial numbers of the case for easy reference. Always refer to both model and
serial numbers in your correspondence regarding the case.

Case Model__________________________ Serial Number______________________
Condensing Unit Model________________ Serial Number______________________

This manual cannot cover every installation, use, or service situation. If you need additional
information, call or write us:

Warranty/Technical Service Department

Toll Free [phone]
WI Phone [phone]

[e-mail]

WARNING LABELS & SAFETY
INSTRUCTIONS

This is the safety-alert symbol. When you see this symbol on your case or
in the manual, be alert to the potential for personal injury or damage to
your equipment.

Be sure you understand all safety messages and always follow recommended precautions and safe
operating practices.

You must make sure that everyone who installs, uses, or services your case is thoroughly familiar with
all safety information and procedures.

Important safety information is presented in this section and throughout the manual. The
following signal words are used in the warnings and safety messages:

DANGER: Severe injury or death will occur if you ignore the message.
WARNING: Severe injury or death can occur if you ignore the message.
CAUTION: Minor injury or damage to your case can occur if you ignore the message.
NOTICE: This is important installation, operation, or service information. If you ignore the

The warning and safety labels shown throughout this manual are placed on your Fede ral Industries case

NOTICE TO EMPLOYERS

message, you may damage your case.

at the factory. Follow all warning label instructions. If any warning or safety labels become lost or
damaged, call our customer service department at 1(800) 356-4206 for replacements.

DANGER

HIGH VOLTAGE.
Turn power off
before servicing.
May have more than
one disconnect

CA UTION
HAZARDOUS MOVING PARTS
DO NOT OPERATE UNIT WITH
DISPLAY PANS REMOVED.

switch.

This label is located on the back of the display case. This label is located below the display pan.

Floor surface around case may become slippery.

Excess condensation can occur and run onto the
floor if case is operated in an environment
above recommended temperature and humidity
levels.

Case is designed to operate in an environment
not to exceed 75º F.

This label is located on the back of the display case.

PRE-INSTALLATION PROCEDURES

Inspection For Shipping Damage

You are responsible for filing all freight claims with the delivering truck line. Inspect all cartons
and crates for damage as soon as they arrive. If damage is noted to shipping crates or
cartons, or if a shortage is found, note this on the bill of lading (all copies) prior to signing.

If damage is discovered when the case is uncrated, immediately call the delivering truck line
and follow-up the call with a written report indicating concealed damage to your shipment. Ask
for an immediate inspection of your concealed damage item. Crating material must be
retained to show the inspector from the truck line.

INSTALLATION INSTRUCTIONS

Locating The Display Case

The case should be located where it is not subjected to the direct rays of the sun, heating
ducts, grills, radiator, or ceiling fans, nor should it be located near open doors or main door
entrances. Also, avoid locations where there is excessive air movement or air disturbances.

The condenser air inlet is located at the rear of the case. Do not block this inlet and do not
locate the air inlet near a source of heat.

Removing Case from Shipping Skid

CAUTION: Do not push against the curved glass, end glass, doors, or

doorframes when removing the case from the skid or moving

Move the case as near as possible to the final location before removing it from the
shipping skid.

Remove the screws that secure the case to the skid.