Federal LPRSS Series, ELPRSS Series, LPRSS3, LPRSS4, LPRSS5 Installation & Operation Instructions

...

Download

Page 1

E2915-3 Rev. A 09/01/2018

Installation & Operation Instructions

Refrigerated LPRSS & ELPRSS Models

Federal Industries 215 Federal AVE Belleville, WI 53508

Toll Free: (800) 356-4206 WI Phone: (608) 424-3331 Fax: (608) 424-3234

Page 2

Page 2 of 40

Contents

(1) Introduction ..................................................................................................................................... 4

1.1 Serial Number ............................................................................................................................... 4

(2) Warning Labels & Safety Instructions .............................................................................................. 5

(3) Pre-Installation Procedures ............................................................................................................. 6

3.1 Inspection for Shipping Damage .................................................................................................. 6

(4) General Electrical & Grounding ....................................................................................................... 7

4.1 Cord Connected ............................................................................................................................ 7

4.2 Permanent Connected (Option) ................................................................................................... 7

(5) Installation Instructions ................................................................................................................... 8

5.1 Locating the Display Case ............................................................................................................. 8

5.2 Removing Case From Shipping Skid and General Installation ..................................................... 8

5.3 Cleaning ........................................................................................................................................ 8

5.4 Center Panel Joining (Option) ...................................................................................................... 8

5.5 Refrigeration System .................................................................................................................. 10

5.5.1 Self Contained Models ............................................................................................................ 10

5.5.2 Remote Models ...................................................................................................................... 10

5.6 Evaporator Condensate Drain Tube ........................................................................................... 10

5.7 Condensate Pump ...................................................................................................................... 11

(6) Shelving Installation & Removal .................................................................................................... 13

6.1 Metal Shelves ............................................................................................................................. 13

6.2 Glass Shelves .............................................................................................................................. 14

6.3 Optional Shelf Lights (ELPRSS) .................................................................................................... 15

(7) Plastic End Removal & Installation ................................................................................................ 16

(8) Rear Doors (Options) ..................................................................................................................... 17

(9) Night Curtain .................................................................................................................................. 18

(10) Security Night Curtain (Option) ..................................................................................................... 19

(11) Operating Instructions ................................................................................................................... 20

11.1 User Controls Overview ............................................................................................................. 20

11.2 Using the electronic control ....................................................................................................... 21

11.2.1 Button and Display Overview ................................................................................................. 21

11.2.2 Powering on control ............................................................................................................... 21

11.2.3 Adjusting the set point ........................................................................................................... 22

11.2.4 Entering manual defrost mode............................................................................................... 22

11.2.5 Error codes .............................................................................................................................. 22

11.3 Initial Startup .............................................................................................................................. 23

11.4 Placing Product in Case .............................................................................................................. 24

(12) Maintenance .................................................................................................................................. 26

12.1 Light Replacement ...................................................................................................................... 26

(13) Periodic Maintenance .................................................................................................................... 27

13.1 Cleaning Condenser Coil............................................................................................................. 27

Page 3

Page 3 of 40

(14) Cleaning Instructions ..................................................................................................................... 28

14.1 Daily Cleaning ............................................................................................................................. 28

14.2 Weekly Cleaning ......................................................................................................................... 28

(15) Sale & Disposal ............................................................................................................................... 31

15.1 Owner Responsibility ................................................................................................................. 31

(16) Service Information ........................................................................................................................ 32

16.1 Pre-Service checklist ................................................................................................................... 32

16.1.1 Case does not operate ............................................................................................................ 32

16.1.2 Lights do not operate ............................................................................................................. 32

16.1.3 Case temperature too warm (product is exceeding 41°F) ..................................................... 32

16.2 Special Service Instructions ........................................................................................................ 33

16.3 Refrigeration & Electrical Data ................................................................................................... 33

16.4 Electronic Control Operation ..................................................................................................... 33

16.4.1 Operation ................................................................................................................................ 33

16.4.2 Defrost Cycle ........................................................................................................................... 34

16.5 Control Parameters .................................................................................................................... 34

16.6 Error Codes ................................................................................................................................. 34

16.7 Refrigeration Operation ............................................................................................................. 35

16.7.1 Self Contained Models ............................................................................................................ 35

16.7.2 Remote Models ...................................................................................................................... 35

(17) Wiring Diagrams ............................................................................................................................. 37

17.1 Self Contained ............................................................................................................................ 37

17.2 Remote ....................................................................................................................................... 37

(18) Replacement Parts ......................................................................................................................... 38

Tables

Table 1- Shelf Loading Limits .................................................................................................................... 24

Table 2 - Electrical Ratings ........................................................................................................................ 33

Table 3 - Control Parameters .................................................................................................................... 34

Table 4 - Error Codes and Resolutions ...................................................................................................... 34

Table 5 - Temperature Probe Common Resistance Chart ........................................................................ 35

Page 4

Page 4 of 40

(1) INTRODUCTION

Thank you for purchasing a Federal Industries display case. This manual contains important instructions for installing and servicing the LPRSS refrigerated self-service merchandisers. A repair parts list and wiring diagram are also included in the manual. Read all of these documents carefully before installing or servicing your case.

NOTICE

Read this manual before installing your case. Keep this manual and refer to it before doing any service on the equipment. Failure to do so could result in personal injury or damage to the case.

NOTICE

Installation and service of the electrical components in the case must be performed by a licensed electrician.

The portions of this manual covering components contain technical instructions intended only for persons qualified to perform electrical work.

DANGER

Improper or faulty hookup of electrical components in the case can result in severe injury or death.

All electrical wiring hookups must be done in accordance with all applicable local, regional, or national standards.

1.1 SERIAL NUMBER

Record the model and serial numbers of the case for easy reference. Always refer to both model and serial numbers in your correspondence with Federal regarding the case.

Case Model__________________________ Serial Number______________________ Condensing Unit Model________________ Serial Number______________________

This manual cannot cover every installation, use, or service situation. If you need additional information, call or write us:

WARRANTY/TECHNICAL SERVICE DEPARTMENT Federal Industries 215 Federal AVE Belleville, WI 53508 Toll Free (800) 356-4206 / WI Phone (608) 424-3331

Page 5

Page 5 of 40

(2) WARNING LABELS & SAFETY INSTRUCTIONS

This is the safety-alert symbol. When you see this symbol on your case or in the manual, be alert to the potential for personal injury or damage to your equipment.

Be sure you understand all safety messages and always follow recommended precautions and safe operating procedures.

NOTICE TO EMPLOYERS:

You must make sure that everyone who installs, uses, or services your case is thoroughly familiar with all safety information and procedures.

Important safety information is presented in this section and throughout the manual. The following signal words are used in the warning and safety messages:

DANGER:

Severe injury or death will occur if you ignore the message.

WARNING:

Severe injury or death can occur if you ignore the message.

CAUTION:

Minor injury or damage to your case can occur if you ignore the message.

NOTICE:

This is important installation, operation, or service information. If you ignore the message, you may damage your case.

The warning and safety labels shown throughout this manual are placed on your Federal Industries case at the factory. Follow all warning label instructions. If any warning or safety labels become lost or damaged, call our customer service department at (800) 356-4206 for replacements.

This label is located on the back of the display case

This label is located below the display pan.

Page 6

Page 6 of 40

(3) PRE-INSTALLATION PROCEDURES

3.1 INSPECTION FOR SHIPPING DAMAGE

You are responsible for filing all freight claims with the delivering truck line. Inspect all cartons and crates for damage as soon as they arrive. If damage is noted to shipping crates, cartons, or if a shortage is found, note this on the bill of lading (all copies) prior to signing.

If damage is discovered when the case is uncrated, immediately call the delivering truck line and follow up the call with a written report indicating concealed damage to your shipment. Ask for an immediate inspection of your concealed damage item. Crating material must be retained to show the inspector from the truck line.

Page 7

Page 7 of 40

(4) GENERAL ELECTRICAL & GROUNDING

DANGER:

Improper or faulty hookup of electrical components in the display case can result in severe injury or death.

4.1 CORD CONNECTED

All standard models are supplied with a power cord that is properly sized to the amperage requirements of the case. See the electrical data plate located on the rear left interior of the case for the proper circuit size for each case. The cord is factory installed protruding from the bottom rear corner of the case. A separate circuit for each display case is required to prevent other appliances on the same circuit from overloading the circuit and causing malfunction.

4.2 PERMANENT CONNECTED (OPTION)

Only a licensed electrician must perform all case electrical connections. All electrical wiring hookups must be done in accordance with all applicable local, regional, or national electrical standards. A separate circuit for each display case is required to prevent other appliances on the same circuit from overloading the circuit and causing malfunction. The electrical service must be grounded upon installation. See the electrical data plate located at the rear of the case for proper circuit size and wire ampacity. The electrical connection box is accessible from the rear of the case with rear grill removed.

FIELD CONNECTION BOX

POWER CORD OR CONDUIT CONNECTION HOLE (7/8"O)

REAR BASE PANEL

(6) REAR BASE PANEL SCREWS

Page 8

Page 8 of 40

(5) INSTALLATION INSTRUCTIONS

5.1 LOCATING THE DISPLAY CASE

The case should be located where it is not subjected to the direct rays of the sun, heating ducts, grills, radiator, or ceiling fans, nor should it be located near open doors or main door entrances. Also, avoid locations where there are excessive air movement or air disturbances.

The case requires a minimum of 6 inches of clearance at the rear of the unit for air discharge. Do not locate case with back tight against the wall. The louvers located on front of base must remain clear for air intake. If rear clearance or front clearance is not possible see a Federal representative for air intake and discharge kit options.

No clearance is needed on sides of the unit.

5.2 REMOVING CASE FROM SHIPPING SKID AND GENERAL INSTALLATION

CAUTION:

Do not push or pull against the top panel, plastic end, end glass, or door frames when removing the case from the skid or moving the case. Case damage or glass breakage could result.

1. Remove crate top and sides and note missing or damaged items as explained in the pre-installation

procedures outlined above.

2. Move the case as near as possible to the final location and before removing it from the shipping skid.

3. Remove the (4) brackets that secure the case to the shipping skid.

4. Prepare cabinet according to instructions in this section that pertain to your model.

5. Lift the case off of skid and into required position. Only lift the case from under the rear lip and front

bottom trim channel above the base. Note: Do not push or pull on front bottom trim channel or lift using the plastic end panel.

6. The case must be level for proper drainage of defrost condensate to the condensate evaporator. Using

the wrench provided level and square the case as needed by adjusting the leg leveler in each corner of base. The 6ft cases also have a set of leg levelers in the center. These must be adjusted so the base is flat.

7. The leveled case must be sealed to the floor using a NSF listed sealant.

5.3 CLEANING

For initial setup, clean the case as outlined in the “Weekly Cleaning” section of this manual.

5.4 CENTER PANEL JOINING (OPTION)

If your cases where ordered with the Center Panel Joining Option you will need to perform the following installation procedures.

Page 9

Page 9 of 40

FRONT JOINING BRACKET

REAR JOINING TRIM

CENTER PANEL BASE MOUNTING HOLES (4)

RIGHT CASE

LEFT CASE

LEFT CASE REAR BASE PANEL

LEFT CASE FRONT BASE PANEL

TOP JOINING BRACKET

INTERIOR JOINING FLANGE

1. Place the right case into desired location and level case by adjusting leg levelers with provided

wrench.

2. Remove the front base panel (4) screws and rear base panels (6) screws from the left case. Push

the left case end tightly against the right case end. The rear joining trim on the right case must be behind the back panel of the left case and the front joining bracket on the right case must be inside the front aluminum trim channel of the left case.

3. Adjust the leg levelers on the left case so it is level and exactly aligned with the right case. The (4)

base mounting hole in the right case panel must align with the (4) mounting holes located in base compartment of left case.

4. Push the cases together as tightly as possible and the gap between the cases must be tight and

even. If the gap is larger at the top or the bottom adjust leg levelers accordingly. HOLD CASES TOGETHER AS TIGHT AS POSSIBLE WHILE ATTACHING ALL JOINING BRACKETS AND DO NOT OVER TIGHTEN SCREWS OR SCREWS WILL STRIP OUT.

5. Attach the bottom of the left case to the right case center panel base mounting holes through the

holes located inside of the left case base. Use the (4) large 10-12x1/2 screws provided.

6. Attach the rear top of left case through the holes in the rear joining bracket using the (3) black

#10-12x1/2 self drilling screws provided.

7. Attach the front of left case through the holes in the front joining bracket using the (2) smaller

#8-12x1/2 self drilling screws provided.

8. Attach the top of left case through the holes in the top joining bracket using the (2) smaller

#8-12x1/2 self drilling screws provided.

9. Attach the interior of left case through the holes in the interior joining flange using the (3) smaller

#8-12x1/2 self drilling screws provided

10. If any there are any gaps along the joining seam fill them with NSF black silicone.

11. Reinstall front and rear grills.

Page 10

Page 10 of 40

5.5 REFRIGERATION SYSTEM

5.5.1 Self Contained Models

The self-contained models are shipped from the factory with a completely operational 404A refrigeration system and require no modifications or adjustments upon installation. Case must be installed as per the installation section of this manual to provide proper condensing air cooling.

5.5.2 Remote Models

The remote models are designed to use 404A refrigerant and shipped from the factory with the evaporator coil, expansion valve, sight glass, service valves and refrigerant solenoid valve. Installation must be performed by a licensed Refrigeration Technician. See the Service section of this manual for installation requirements.

5.6 EVAPORATOR CONDENSATE DRAIN TUBE

WARNING TO INSTALLER:

Evaporator Condensate Drain Tube may become dislodged during shipping. Installer must check Evaporator Condensate Drain Tube upon installation to be sure drain tube is properly seated and installed correctly.

Evaporator Drain Tube must be attached to tube protruding from bottom of Evaporator Tub and must either be inside the Condensate Pan area or inside of hole of Condensate Pump.

Page 11

Page 11 of 40

5.7 CONDENSATE PUMP

A condensate pump is Standard on some models and Optional on all models. Installer must check unit to see if a condensate pump has been provided with case.

WARNING TO INSTALLER:

Installer must determine if case was provided with condensate pump. Failure to hook up pump hose to drain will cause water on floor and cause a slip hazard.

Page 12

Page 12 of 40

Instead of using heat energy to remove condensate run off from the evaporator coil a condensate pump moves the water to a nearby drain.

• The Condensate Pump is provided with 50ft of clear 1/2in OD x 3/8in ID tubing that must be run out of

the base area to a drain.

• There are several drain tube exit locations provided in the base as noted in the drawing above. Plugs or

caps will need to be removed in the desired exit location.

• The hose can be run the entire 50ft in any direction as required, but no higher than 20ft from the

pump base. A check valve is provided in the pump to prevent water from flowing back into the reservoir. For best efficiency extend the hose level below the level of the pump base to create a siphoning effect. Never run the hose to or through an area below freezing (32°F, 0°C) or freezing water will block the tube.

Page 13

Page 13 of 40

(6) SHELVING INSTALLATION & REMOVAL

6.1 METAL SHELVES

SHORTER TOP SHELF

WIDER BOTTOM SHELF

SHORTER TOP SHELF BRACKET

LONGER BOTTOM SHELF BRACKET

SHELF NOTCH

SHELF BRACKET FRONT TAB

1. Follow the instructions in the illustration below and insert (1) of the shelf brackets in the desired shelf

standard slot on one side of the case. Place the additional bracket in the same shelf standard slot on the opposite end of case. If the case was supplied with shelf light option (ELPRSS), the bracket with a clear plastic cord retainer clip must be on the side with the shelf light. For LPRSS case with (2) shelves repeat for shorter top shelf brackets.

0v NOTCH

6v NOTCH

INSTALLATION

REMOVAL

TOP HOOK

BOTTOM TAB

SHELF BRACKET

SHELF STANDARD

1. Place shelf bracket top hook into desired shelf standard slot.

2. Lift shelf bracket top hook to allow shelf bracket bottom tab to clear shelf standard slot.

3. Swing shelf bracketbottom tab into shelf standard slot.

4. Place the desired shelf bracket notch of 0, 6, or 12 degrees onto bottom of shelf standard slot.

1. Lift shelf bracket up to allow shelf bracket notch to clear the bottom of shelf standard slot.

2. Swing shelf bracket bottom tab out of shelf standard slot.

3. Drop shelf bracket down to allow shelf bracket top hook to clear top of shelf standard slot.

4. remove shelf bracket top from shelf standard slot.

CLEAR BUMPER TOWARDS END PANEL

2. Place the longer bottom shelf on top of the longer bottom shelf brackets with the flanges on each end of

the shelf overhanging the outside of the bracket. Place the front tab of the shelf bracket into the notch located on the front of the shelf.

Page 14

Page 14 of 40

3. On the LPRSS case with (2) shelves place the shorter top shelf on top of the shorter top shelf brackets

with the flanges on each end of the shelf overhanging the outside of the bracket. Place the front tab of the shelf bracket into the notch located on the front of the shelf.

4. If shelf includes optional light (ELPRSS), plug the cords into the plug receptacle located toward rear of

case.

6.2 GLASS SHELVES

SHORTER GLASS TOP SHELF

LONGER GLASS BOTTOM SHELF

SHORTER TOP SHELF BRACKETS

LONGER BOTTOM SHELF BRACKETS

SHELF BRACKET FRONT TAB

SHELF SUPPORT

SHELF SUPPORT, LONG CORD WHEN SUPPLIED WITH SHELF LIGHT OPTION.

CORD RETAINER CLIP ON THIS SIDE WHEN ORDERED WITH SHELF LIGHT OPTION

GLASS SHELF RETAINER CLIPS. MUST INSTALL TO GLASS

GLASS SHELF RETAINER CLIP LOCATED IN FAR CORNER OF GLASS SHELF. (FIELD INSTALLED TO GLASS BOTTOM)

TOP VIEW

CLEAR PRODUCT STOP

CLEAR PRODUCT STOP (FIELD INSTALLED TO GLASS FRONT LIP)

GLASS SHELF RETAINER CLIP

1. When installing for the first time, attach (2) glass shelf retainers to each glass shelf. Remove the backing

from the tape located on the flat side of the glass shelf retainer. Position the glass shelf retainer in the (2) far corners of the glass as shown in the above figure. Repeat for each glass shelf.

NOTE: Clean the area of glass where the glass shelf holder is to be located with isopropyl alcohol and let it air dry before installing the glass shelf holder.

2. When installing for the first time attach (1) clear glass product stop to each glass shelf as shown in the

figure above. Align the clear product stop edge with the edge of the glass and push the “U” portion of the glass product stop onto the glass lip across the entire front of the glass. Repeat for each glass shelf.

3. Install the shelf brackets into the shelf standard as described in Step (1) of “Metal Shelves Installation” of

this manual.

Page 15

Page 15 of 40

4. Place the front of the glass shelf onto the front shelf support.

5. Set the rear side of the glass shelf onto the rear shelf support so that the glass shelf retainers straddle the

rear shelf support.

6. Repeat steps 2 & 3 for each tier.

6.3 OPTIONAL SHELF LIGHTS - ELPRSS

1. Install shelves as described in the Metal Shelves Installation and Glass Shelves Installation sections in this

manual. Note: On models with glass shelves with lights, a shelf support will be placed on the back and front of the shelf bracket.

2. Remove the cap from the appropriate female light sockets.

3. Plug in each shelf light by plugging the male plug on the appropriate shelf light cord plugs with the female

light sockets and push together.

Shelves and shelf light quantity

It is not required that all shelves and shelf lights supplied with each case are used. The quantity of shelves and shelf lights can be tailored to your specific needs. If the supplied quantity of shelves and shelf lights are not required, cap unused female socket located in interior of the case mullion with caps supplied.

Page 16

Page 16 of 40

(7) PLASTIC END REMOVAL & INSTALLATION

(2) VELCRO STYLE PADS ON CASE

PLASTIC END PANEL

(4) SCREWS WITH SPACERS ON CASE

(4) KEY SLOTS IN BACK OF PANEL

(2) VELCRO STYLE PADS ON BACK OF PANEL

Right and Left plastic end panels are ordinarily shipped installed from the factory but can be easily removed for cleaning. Removing end panels make it easier to grab on to case when moving or installing case and can easily be reinstalled.

REMOVAL:

1. Lift the back side of the panel out to disengage (2) Velcro style pads

2. Slide the panel forward to disengage the (4) Key slots in panel from (4) screws in case.

INSTALLATION:

1. Hold panel tightly against the side of the case with the front lip of panel tight against front of case.

2. Slide panel forward about ½ until screws fall into key slots. Slide the panel towards the back of case

making sure all (4) key slots engage.

3. Push in on end panel in location of the (2) Velcro style pads to lock panel in place.

Page 17

Page 17 of 40

(8) REAR DOORS (OPTIONS)

1. LIFT UP

2. SWING BOTTOM OUT

LOWER TRACK

UPPER TRACK

1. Start with the outer door and lift the door upward until the bottom edge of door clears the lower track

and then swing the bottom of the door outward and down out of upper track.

2. After the outer door is removed repeat the procedure for the inner door.

3. Reverse this procedure for door reinstallation. The doors are not interchangeable.

Page 18

Page 18 of 40

(9) NIGHT CURTAIN

NIGHT CURTAIN STRAP WITH SNAP

SNAP

NIGHT CURTAIN HOLDER BRACKETS

FRONT TRIM

OPENING:

1. Grab night curtain strap and lift the rolled night curtain out of the night curtain holder brackets. Pull

the night curtain across the top of case and down the front.

2. Attach the snap located under the night curtain strap on to the snap located on the front trim.

CLOSING:

1. Grab the night curtain strap and detach the snap from the snap located in the front top trim.

2. While holding the night curtain strap allow the night curtain to roll up and place the rolled night curtain

carefully into the night curtain holder brackets.

Note: The 5’ and 6’ models have (2) night curtains.

Page 19

Page 19 of 40

(10) SECURITY NIGHT CURTAIN (OPTION)

SECURITY NIGHT COVER LOCK HANDLE

SECURITY NIGHT COVER FRONT HANDLE

SECURITY NIGHT COVER LOCK HANDLE CATCH

FRONT TRIM

BOTTOM FLANGE

TOP FLANGE

TOP PANEL

REMOVAL:

1. Unlock the lock handle and turn handle to disengage from lock handle catch.

2. Grab the lock handle and the front handle and lift the cover straight up out of the case opening.

INSTALLATION:

1. Turn the lock handle so the latch is horizontal to the top of the case.

2. Holding the lock handle and the front handle place the bottom flange of the security night cover inside

of case opening. The bottom flange of the security night cover must be tight against the flat inner side of the front trim.

3. Set the top flange of the security cover down against the top panel.

4. Turn the lock handle so it engages the lock handle catch and use key to lock it in place.

Note: The 6’ models have (2) security covers.

IMPORTANT: Cleaning the Acrylic plastic security night cover require special care to prevent hazing of

material. Lightly dust (not wipe) the surface with clean soft cloth. Then the surface can be wiped carefully with a soft, wet cloth or chamois. The cloth or chamois must be kept free of grit by frequently rinsing in clean water. Grease and oil can be removed with kerosene. Do not use window cleaners or kitchen scouring compounds. DO NOT use solvents such as Acetone, Benzene, Carbon Tetrachloride, and Lacquer Thinners. A spray wax such as Pledge or Maguire’s polish can be applied and wiped with a clean soft cloth. The wax tends to fill in and hide small scratches.

Page 20

Page 20 of 40

(11) OPERATING INSTRUCTIONS

11.1 USER CONTROLS OVERVIEW

POWER SWITCH

TEMPERATURE CONTROL

LIGHT SWITCH

Power Switch

The unit has a power switch that turns off power to the entire unit, including the condensate evaporator and the lights. This switch is located behind a lift up panel on the unit base.

Light Switch

The unit has a light switch that turns on and off the interior lights of unit. The switch is located inside the display case on the left upright frame member near the top.

Temperature Control

Located in the front grille of the display case, the temperature control allows the user to adjust the temperature of the display merchandiser to their needs.

Page 21

Page 21 of 40

11.2 USING THE ELECTRONIC CONTROL

POWER TOGGLE & SET POINT UP ADJUST

MANUAL DEFROST AND SET POINT DOWN ADJUST

SET POINT ADJUST MODE

DIGITAL DISPLAY

11.2.1 Button and Display Overview

Press and hold this button for 3s to turn system on (if off) or off (if on). Also used to adjust set point when in set point adjust mode

Press to enter set point adjust mode, confirm set point changes, and mute alarms.

Press and hold this button for 3 seconds to initiate a manual defrost (and cancel defrost if initiated), also adjusts set point down when in set point adjust mode

Press both buttons simultaneously to check air stream probe temperature. This is not an indicator of product temperature.

11.2.2 Powering on control

To turn power on to the refrigeration system press and hold, for three seconds, the blue up arrow on

the control’s keypad. The keypad will read “On” while the button is depressed. When the system

powers on, the display will read the current set point (a number “1” through “9”). The orange compressor run indicator will illuminate on the display.

Page 22

Page 22 of 40

11.2.3 Adjusting the set point

The set point is what determines how cold the display case will hold food and beverage. To adjust the set point press and hold the wrench button until the display begins to flash a number (three seconds). Then use the up and down arrows of the keypad to scroll through the set point options. There are nine (9) available set points, the higher the number of the set point name, the colder the display case will run, with setting “9” being the coldest and setting “1” being the warmest. Once you have chosen your desired setting press the wrench button again to confirm your choice.

11.2.4 Entering manual defrost mode

In order to initiate a manual defrost press and hold the red down arrow for 3s. The control will read “dEF” while the button is being held. The defrost is initiated when the orange snowflake appears on the control display.

11.2.5 Error codes

It is possible for error codes to be displayed on the control screen. In the event of a malfunction an alarm will sound and a red ringing bell will be displayed on the screen. An error code or codes will flash intermittently on the display. If there are multiple codes, the display will continuously cycle through them. The following photo shows error code “E0” as an example next to the red bell.

You may mute the alarm by pressing and releasing the wrench button. The red ringing bell and all error codes will still be displayed. When the fault is remedied the control will return to normal operation and will automatically clear the codes from the display.

Page 23

Page 23 of 40

11.3 INITIAL STARTUP

After all the checks outlined in the installation section of this manual have been made, the case is ready to be put into service. Turn on the Power at the breaker box and flip the Power Switch and Light Switch on unit to the on position. Also ensure that the control is powered on as described above in “11.2.2”.

At start up from a warm unit, it is recommended that the temperature control is set to a warmer setting, such as 1. After the unit has gone through several cycles, adjust the control to a mid range setting, then to a colder setting if necessary to maintain desired product temperature

NOTICE:

This refrigerated display case is designed to operate in a maximum environment of 75°F (23.9°C) and 55% relative humidity. Exceeding these limits will cause poor case performance and excessive sweating.

Page 24

Page 24 of 40

11.4 PLACING PRODUCT IN CASE

• Do not exceed weight limits shown in the table below when loading product into the display case.

Table 1- Shelf Loading Limits

Model

Top Shelf/ELPRSS Shelf

Bottom Shelf

Display Deck

E/LPRSS3

70lbs (32kg)

100lbs (45kg)

250lbs (114kg)

E/LPRSS4

100lbs (45kg)

135lbs (61kg)

320lbs (146kg)

E/LPRSS5

120lbs (55kg)

170lbs (77kg)

390lbs (177kg)

E/LPRSS6

150lbs (68kg)

210lbs (95kg)

460lbs (209kg)

• Determine desired shelving location before placing product in case. Product must be removed to

readjust shelf location.

• Allow a minimum of 2inches between top of product and bottom of shelf as shown below.

2.00 MIN

LEAVE 1/2" GAP BETWEEN PRODUCT TO ALOW AIR FLOW AROUND PRODUCT

2.00 MIN

Page 25

Page 25 of 40

• Do not overhang the front or rear of shelves with product. Improper clearance in front and rear of shelf

will block the refrigerated air flow and will cause product loss.

• Do not block the slots along the front and rear air discharge slots. Covering these slots will block the

refrigerated air flow and will cause product loss.

• The display deck is removable for cleaning and can become dislodged in shipment. To ensure proper

airflow and performance of the case, make sure that the display deck is pushed completely down.

• Allow refrigerated models to run for at least two hours before placing pre-chilled product into unit.

NOTICE:

Case must be stocked with pre-chilled product only. Product should be at or below 40°F (4.5°C) before adding it to the display case. Use a refrigerator to pull down product that is above 40°F (4.5°C). This display case is temperature holding product only it will not pull down product that is above the recommended temperature..

Page 26

Page 26 of 40

(12) MAINTENANCE

12.1 LIGHT REPLACEMENT

1. All lights are LED Bar type. The TOP LIGHT is attached to LIGHT LINER using plastic clips. SHELF LIGHTS

are attached using double sided tape. If replacement should become necessary follow the directions below to replace LED light.

TOP LIGHT

- Unplug cord from light

- Carefully pry plastic clip tab away from lip on LED light body, with a slight twist

motion, disengage the clip locking tab on each of the plastic clips. Install replacement LED by inserting replacement LED lip on the body under the locking tab on plastic clip.)

- Re-install cord plug.

SHELF LIGHTS

- Unplug cord from light

- Use putty knife to pry LED light body from Shelf and or Top Light Liner. It may be

useful to slide the putty knife along the length of light once putty knife is between LED light body and component surface. (it is recommended to remove shelves from case when replacing LED lights)

- Remove residual adhesive tape from shelf / top light liner and clean surface with

alcohol

- Remove liner from Double Sided Tape on replacement Light

- Use small holes in Top Light Liner & Shelves as a locational guide for LED placement

- Mount light and apply pressure along the length of LED body to ensure good adhesion Re-install shelf and cord plug.

Page 27

Page 27 of 40

(13) PERIODIC MAINTENANCE

13.1 CLEANING CONDENSER COIL

It is very important that the condenser coil is cleaned twice per month to insure proper refrigeration performance and to prevent compressor failure. Failure to clean condenser coil will void condenser warranty.

1. Disconnect power to the unit

2. Remove the front panel located on the front bottom of unit by removing the (4) front panel retaining

screws.

3. Carefully vacuum the front surface of condenser coil. Take care not to bend coil fins with vacuum

cleaner nozzle, a brush attachment works well to prevent this.

4. Reinstall front panel and retaining screws.

(4) FRONT BASE PANEL SCREWS

VACUUM FRONT SURFACE OF CONDENSER COIL

Figure 1 - Condenser Cleaning

Page 28

Page 28 of 40

(14) CLEANING INSTRUCTIONS

14.1 DAILY CLEANING

The case should be cleaned thoroughly, as described in the weekly cleaning section, before it is used for the first time.

NOTICE:

Avoid splashing or soaking any electrical components with water to prevent electrical damage to the case.

NOTICE:

Shut off lights and power switches and remove all product from case. Allow sufficient time for the unit to reach room temperature before proceeding with cleaning.

NOTICE:

Remove all product from case before proceeding with cleaning procedure.

NOTICE:

Acrylic end panels and top panel require special washing procedures to prevent hazing and yellowing of material. Read cleaning of end panel and top panel procedure carefully.

NOTICE:

This case is not designed to be cleaned by flushing.

Note: For major spills or foreign material buildup perform the weekly cleaning instructions.

1. (If Supplied With Optional Rear Doors.) Clean all foreign materials from the door opening and clean

both sides of the doors with a damp cloth

2. Wipe complete interior and exterior of case using a damp cloth.

3. Clean both sides of end glass panels using any common window cleaner.

14.2 WEEKLY CLEANING

This procedure is recommended on a weekly basis. It may need to be performed more often if necessary to maintain a clean, sanitary case. The case should be cleaned to this procedure before using the first time.

NOTICE:

Avoid splashing or soaking any electrical components with water to prevent electrical damage to the case.

NOTICE:

Shut off lights and power switches and remove all product from case. Allow sufficient time for the unit to reach room temperature before proceeding with cleaning.

Page 29

Page 29 of 40

NOTICE:

Remove all product from case before proceeding with cleaning procedure.

NOTICE:

This case is not designed to be cleaned by flushing.

DISPLAY DECK

FAN COVER

FAN SHROUD ASSEMBLY

FAN SHROUD RETAINING LATCH

FAN SHROUD RETAINER

EVAPORATOR AIR DISCHARGE GRILL

EVAPORATOR AIR RETURN GRILL

1. If supplied with rear door option remove both rear doors as described in the “Door Removal” section

of this manual.

2. Remove shelving from unit as described in the “Shelving Installation and Removal” section of this

manual. Remove all interior shelving as described in the shelving installation and removal section of this manual.

3. Remove both shelf standards from interior of case by removing the (2) thumbscrew from top and

bottom.

4. Lift the display deck up and out of evaporator tub.

5. Lift the grab tab of the fan cover and slide the fan cover tabs out of the fan shroud assembly slots. and.

6. Remove the fan shroud assembly by lifting (4) black tabs up on each end of evaporator coil. Lift the

rear of the evaporator fan shroud and slide the front lip out of the fan shroud retainer. Reach in and unplug the evaporator fan motor cord. Remove evaporator fan shroud.

Page 30

Page 30 of 40

7. Clean the entire interior of the case using warm soapy water. Wipe off all soapy water with a damp

cloth and allow to dry. (DO NOT use solvents such as Acetone, Benzene, Carbon Tetrachloride, and Lacquer Thinners)

NOTE: Depending on the amount of usage and spillage of foreign material, some fasteners may have to be removed and parts disassembled to allow proper cleaning of the unit.

8. Clean all shelves, shelf support bars, shelf brackets, and display pans using warm soapy water and a

brush. Rinse thoroughly and allow to dry.

9. If supplied with rear door option clean all foreign material from inner and outer rear door tracks and

clean them and both sides of the doors using warm soapy water and a brush. Apply a light film of lubricant such as PAM to door tracks to make the doors operate smoother.

10. Clean end glass panels using any common window cleaner.

11. Reassemble the case in reverse order.

Page 31

Page 31 of 40

(15) SALE & DISPOSAL

15.1 OWNER RESPONSIBILITY

If you sell or give away your Federal Industries case you must make sure that all safety labels and the Installation-Service Manual are included with it. If you need replacement labels or manuals, Federal Industries will provide them free of charge. Contact the customer service department at Federal Industries at (800) 356-

4206. The customer service department at Federal Industries should be contacted at the time of sale or disposal of

your case so records may be kept of its new location. If you sell or give away your Federal Industries case and you evacuate the refrigerant charge before shipment.

Federal Industries recommends that the charge be evacuated into a recovery system to prevent the possibility of HFC’s from being released into the atmosphere.

Page 32

Page 32 of 40

(16) SERVICE INFORMATION

CAUTION:

RISK OF ELECTRIC SHOCK!!!

DISCONNECT POWER BEFORE SERVICING UNIT!!!

Before any service work is performed on the case, make sure all power is disconnected to the case.

Service problems or request for repair parts from authorized service agencies, trained service personnel, or owners should be referred to:

CUSTOMER SERVICE DEPARTMENT

Federal Industries 215 Federal AVE Belleville, WI 53508

Toll Free: (800) 356-4206 / WI Phone (608) 424-3331

Fax: (608) 424-3234

16.1 PRE-SERVICE CHECKLIST

You may avoid the cost and inconvenience of an unnecessary service call by first reviewing this checklist of frequently encountered situations that can cause unsatisfactory case performance.

CAUTION:

Before servicing case, turn off power at the main breaker of fuse box.

16.1.1 Case does not operate

 Check for disconnected power supply.  Check for tripped breaker or blown fuse.  Check that power switch is on.

16.1.2 Lights do not operate

 Check that light switch is on.  Shelf light: Check that shelf light cords are tight in the sockets

16.1.3 Case temperature too warm (product is exceeding 41°F)

 Check that the cold air inlet and outlet slots are not blocked.  If supplied with rear door option be sure that the rear doors are closed and tightly sealed  Check for blocked or dirty condenser coil fins and clean them (see “13.1 Cleaning Condenser

Coil” page 27).

Page 33

Page 33 of 40

16.2 SPECIAL SERVICE INSTRUCTIONS

There are rare occasions when the refrigerant charge must be evacuated from a case in order to perform service work. In those situations, Federal Industries recommends that the refrigerant charge be evacuated

into a recovery system to prevent the possibility of hydrofluorocarbons (HFC’s) from being released into the

atmosphere. If moisture or liquid is observed around or under a Federal Industries case, an immediate investigation should

be made by qualified personnel to determine the source of the moisture or liquid. The investigation made should determine if the case is malfunctioning or if there is a simple housekeeping problem.

Moisture or liquid around or under a case is a potential slip/fall hazard for persons walking by or working in the general area of the case. Any case malfunction or housekeeping problem that creates a slip/fall hazard around or under a case should be corrected immediately.

16.3 REFRIGERATION & ELECTRICAL DATA

Table 2 - Electrical Ratings

SELF CONTAINED

REMOTE

MODEL

404A

REFRIG.

VOLTAGE

AMPERAGE

CORD STYLE

VOLTAGE

AMPERAGE

CORD STYLE

LPRSS3 ELPRSS3

2 LBS

120/60/1

20AMP

NEMA 5-20

120/60/1

15AMP

NEMA 5-15

LPRSS4 ELPRSS4

3 LBS

120/60/1

20AMP

NEMA 5-20

120/60/1

15AMP

NEMA 5-15

LPRSS5 ELPRSS5

4 LBS

230/60/1

15AMP

NEMA 6-15

120/60/1

15AMP

NEMA 5-15

LPRSS6 ELPRSS6

4 LBS

230/60/1

15AMP

NEMA 6-15

120/60/1

15AMP

NEMA 5-15

16.4 ELECTRONIC CONTROL OPERATION

This unit is equipped with an electronic temperature control. The control parameters are set at the factory and cannot be manually changed in the field. The pre set control parameters are listed on the chart in the Settings Chart below.

16.4.1 Operation

The control uses two sensors, one located in the air stream and one located on the evaporator coil. The sensor located in the air stream is referred to as the temperature control sensor. The sensor located on the evaporator coil is referred to as the defrost probe.

The temperature control sensor is located on the plastic tub behind the evaporator coil on the centerline of the display case in the cold air stream. The sensor location is critical for proper operation on the unit. Do not move or relocate this sensor.

The coil sensor is strapped to the evaporator coil. This sensor location is critical for proper operation of the unit. Do not move or relocate this sensor.

Page 34

Page 34 of 40

The temperature control is set to cut in at 38°F (3.3°C). The Temp control cuts out at 16°F (-8.9°C) at

the coldest setting (“9”) and 28°F (-2.2°C) at the warmest setting (“1”). See “11.2 Using the electronic control” on page 21 for more details on using the control.

16.4.2 Defrost Cycle

The control is programmed to initiate defrost via two different methods. There are 3 programmed defrost cycles in the case which will initiate a defrost cycle every 8 hours. The unit does not have a time clock so the defrost cycles cannot be set for any specific time of day.

The unit also has an ‘On demand’ defrost feature that will initiate a defrost when the temperature differential between the evaporator temperature and the air temperature is more than 12°F (6.7°C) for 5 minutes after 30 minutes into the refrigeration cycle (e.g. if the air stream probe measures 32°F/0°C or greater and the defrost probe measures 20°F/-6.7°C or lower for five minutes). Once initiated the defrost cycle will terminate when evaporator coil sensor reaches 45°F (7.2°C).

If a manual defrost is required, one can be initiated by pressing and holding the down arrow for three (3) seconds. This is typically unnecessary and should only be performed if special circumstances require it.

16.5 CONTROL PARAMETERS

Table 3 - Control Parameters

Parameter Description



Control Setpoint 

1 2 3 4 5 6 7 8 9

Compressor Cut in [°F]

38.0

Compressor Cut out [°F]

28.0

26.5

25.0

23.5

22.0

20.5

19.0

17.5

16.0

Compressor Min On Time

5 min

Compressor Min Off Time

2 min

Compressor Max Run Time

75 min

Defrost Termination Temp [°F]

45.0

Time to first defrost

8 hr

Time to subsequent defrost

8 hr

Defrost duration

30 min

Defrost on demand differential [°F]

12.0

Delay for defrost on demand

5 min

Time delay to the next defrost on demand

30 min

16.6 ERROR CODES

Error codes may be encountered if either the controller or the display case is malfunctioning. The following is a list of error codes that may be encountered.

Table 4 - Error Codes and Resolutions

Code

Description

Cause

Resolution

Page 35

Page 35 of 40

Temperature probe error

Probe signal is interrupted or short-circuited

1. Check to ensure probe wires and quick

disconnect are secure in control.

2. Check probe resistance to table below. If 0

resistance is present check wiring insulation. If infinite resistance is present check for breaks in wiring (meter will likely read overload or very high in the mega-ohm range).

3. Ensure that probes are wired per the wiring

diagram provided.

4. Replace probe if other remedies fail, or if

probe resistance deviates from “Table 5” below

Defrost probe error

See E0

Unit parameter reading error

Operating conditions

1. Remedy abnormal operating conditions. The

control is rated to operate in a range of 14 to 122°F (-10 to 50°C) and less than 90%RH noncondensing.

2. Replace control if problem persists.

Operating parameter reading error

See EE

Table 5 - Temperature Probe Common Resistance Chart

Probe Temp

Maximum Resistance [Ω]

Normal Resistance [Ω]

Minimum Resistance [Ω]

32°F (0°C)

27.83

27.28

26.74

77°F (25°C)

10.1

9.9

212°F (100°C)

0.97

0.94

16.7 REFRIGERATION OPERATION

16.7.1 Self Contained Models

The unit temperature is controlled by the electronic control outlined in the control section of this manual.

Note: The condenser fan runs continuously.

16.7.2 Remote Models

Refrigeration R404 Charge

CHARGED IN FIELD

Remote Low Press. Switch Cut In

50 psi

Remote Low Press. Switch Cut Out

15 psi

Adjustable Head Master

200 psi

Remote High Press. Switch Cut Out

400 psi

The remote models are designed to use 404A refrigerant and shipped from the factory with the evaporator coil, expansion valve, sight glass, and refrigerant solenoid valve. Filter Drier must be installed in field. Electronic control runs identical to the self contained models except the electronic control opens and closes a

Page 36

Page 36 of 40

refrigeration solenoid valve located on the suction line instead of turning on and off a compressor. The solenoid valve closes and shuts off the refrigeration flow to the unit and initiates a pump down cycle. This will allow the remote low pressure switch to open and shut off remote compressor.

The condensing unit and pressure controls are optionally supplied from the factory for remote location installation. The condensing unit must be mounted and wired by the installer. The high low pressure switch must be wired in series with the compressor power supply as shown in diagram below

1. Mount condensing unit indoors as close to the remote display case as practical. The refrigeration line

should be as short as possible and must not exceed 30 feet.

2. All refrigeration and/or electrical materials between the condensing unit and display case are to be

supplied by installing contractor.

3. Route properly sized and designed refrigeration lines from the condensing unit to the cabinet.

4. Horizontal suction lines should be pitched downward towards the condensing unit at least ½” per 10’

run to aid the oil drainage. A “P” trap must be installed in the suction line at the foot of every riser to

insure oil return. Dry nitrogen must be used to flow through tubing while brazing refrigeration lines.

5. Suction line must be insulated the entire length with Armaflex (or equivalent). Do not run liquid line

inside insulation with suction line.

6. The remote high/low-pressure control must be mounted, wired and set pressures by the installer.

7. Leak check condensing unit, cabinet, and all connecting tubing. Cabinet and condensing unit tubing

should be checked to insure no leaks occurred during shipping or from rough handling.

8. Make certain all refrigeration valves are opened and evacuate system to 500 microns. Charge the

system with refrigerant type specified on the data plates.

REMOTE HIGH LOW PRESSURE CONTROL

LIQUID LINE

SUCTION LINE (INSULATED)

REMOTE CONDENSING UNIT

EVAPORATOR COILS

DISPLAY CASE

EXPANSION VALVE

HIGH

LOW

LIQUID LINE SOLENOID VALVE

SIGHT GLASS

DRIER/FILTER

FIELD CONNECTION

HOT

FUSED POWER SUPPLY

DEFROST TERMINATE PROBE

ELECTRONIC CONTROL

AIR TEMP. CONTROL PROBE

FUSED CASE POWER

Figure 2 - Remote Refrigeration Diagram

Page 37

Page 37 of 40

(17) WIRING DIAGRAMS

17.1 SELF CONTAINED

LAMP

TOP LIGHT

LAMP

BLU

BLK

SHELF LIGHT

LAMP

POWER

SUPPLY

BLK

BLU

SHELF LIGHT

COLOR CODE

B = BLUE Y = YELLOW

W = WHITE

R = RED

BLK = BLACK

BRW= BROWN

CORD & PLUG

91-19493 REV C - 5/1/18

CONDENSATE PUMP

OR EVAPORATOR

BLK

EVAP. FAN

BLK/RIB

BLK

BLK/RIB

BLK

BLK/RIB

BLK

FAN

4 5

RELAY

LAMP

BLU

BLK

POWER SUPPLY

BLK

TOP LIGHT

TOP & SHELF LIGHTS (OPTIONAL)

TOP LIGHT ONLY

BLK

EVAP. FAN

BLK/RIB

BLK

BLKBLK

4', 5' AND 6' MODELS

PLUG

LIGHT SWITCH

DARK LINES REPRESENT (3) CONDUCTOR CORD

BLK

POWER

BLU

SWITCH

HI/LO PRESS SWITCH, NC

BLK

COMPRESSOR

Y/G

G = GREEN

NOTE PROBE WIRING

BLK

SEE CAREL WIRING

TEMP PROBE

DEFROST PROBE

ALTERNATE CONTROL (RANCO)

9 8

7654

CAREL CONTROL

9 8

7654

TEMP PROBE

DEFR

RANCO

BLU

17.2 REMOTE

COLOR CODE

B = BLUE Y = YELLOW

W = WHITE

R = RED

BLK = BLACK

BRW= BROWN

CORD & PLUG

91-19494 REV B - 06/05/18

CONDENSATE PUMP

OR EVAPORATOR

BLK

EVAP. FAN

BLK/RIB

BLK

BLK/RIB

BLK

BLK/RIB

BLK

EVAP. FAN

BLK/RIB

BLK

4', 5' AND 6' MODELS

PLUG

DARK LINES REPRESENT (3) CONDUCTOR CORD

BLK

POWER

SWITCH

HI/LO PRESS SWITCH, NC

BLK

Y/G

G = GREEN

NOTE PROBE WIRING

BLK

SEE CAREL WIRING

TEMP PROBE

DEFROST PROBE

ALTERNATE CONTROL (RANCO)

9 8

7654

CAREL CONTROL

9 8

7654

TEMP PROBE

DEFR

RANCO

REFRIG SOLENOID

FAN

RELAY

REMOTE

COMPRESSOR

HI/LO PRESS SW

OPTIONAL REMOTE MOUNTED & WIRED COMPONENTS

ALL FIELD WIRED

SEPARATE POWER SUPPLY

PRESSURE

CONTROL

REMOTE

LAMP

BLU

BLK

POWER SUPPLY

BLK

TOP LIGHT

TOP LIGHT ONLY

LIGHT SWITCH

BLU

LIGHT SWITCH

SHELF LIGHT

BLK

POWER

SUPPLY

SHELF LIGHT

BLK

BLU

LAMP

TOP & SHELF LIGHTS (OPTIONAL)

LAMP

TOP LIGHT

BLU

LAMP

Page 38

Page 38 of 40

(18) REPLACEMENT PARTS

REFRIGERATION

LPRSS3,

ELPRSS3

120V

LPRSS4,

ELPRSS4

120V

LPRSS5,

ELPRSS5

240V

LPRSS6,

ELPRSS6

240V

Condensing Unit (Self Contained)

30-17726

30-17887

30-17888

Evaporator Coil

33-17700-1

33-17700-2

33-17700-3

33-17700-4

TXV Expansion Valve

32-19420

32-19419

32-19416

Filter Drier

32-12626

Site Glass (LPRSS ONLY)

32-54010

Temperature Control

32-19445

Temperature Probe

32-19094

Control Display

32-19446

Digital Display Ribbon Cable

32-19093

Pressure Control

32-51009

Evaporator Fan Motor Self Cont.

41-16025

41-17811

Evaporator Fan Motor Remote

41-16025

Evaporator Fan Blade (Before 5/13)

72-11450 (1)

72-17987 (2)

72-11450 (2)

Evaporator Fan Blade (After 5/13)

72-11450 (1)

72-11450 (2)

Latch Evaporator Housing to Coil

66-13640

Condnsate Pump (Std 5 & 6)

47-15686

47-15687

Condensate Base Fan Motor(Opt on Rem)

41-11628

Condensate Base Fan Blade(Opt on Rem)

72-32507

Condensate Pan Ass'y (Std 3 & 4)

SA5202

Condensate Pan PTC Heater

40-19498

Condensate Pan Wick

15-19469

Condensate Drain Tube

06-17699

SA5210

Thermometer

32-13662

ELECTRICAL

LPRSS3,

ELPRSS3

120V

LPRSS4,

ELPRSS4

120V

LPRSS5,

ELPRSS5

240V

LPRSS6,

ELPRSS6

240V

Light Switch

41-11066

Power Switch

41-18186

LED Light Power Supply

39-20986

Top Light Cord

43-20860-1B

LED Light

42-20871-

25C35

42-20871-

38C35

42-20871-

48C35

42-20871-

66C35

LED Plastic Mounting Clip

67-20869

Harness Power Supply

43-20974

Page 39

Page 39 of 40

Top Shelf Light Cord (ELPRSS Optional)

43-20862-3B

Bottom Shelf Light Cord (LPRSS)

43-20862-4B

Main Wire Harness

43-19492

Power Cord

43-30818

43-17839

Wiring Diagram

91-19493 SC / 91-19494 REM

LPRSS PANELS

LPRSS3

LPRSS4

LPRSS5

LPRSS6

Glass End Clear

50-17701

Glass End Reflective Left(Optional)

50-17701-1L

Glass End Reflective Right(Optional)

50-17701-1R

End Panel Mirror Int.Left(Optional)

SA4287-L

End Panel Mirror Int.Right(Optional)

SA4287-R

Cover Top Black

M15910-1

M15910-2

M15910-3

M15910-4

Cover Top Stainless (Optional)

M15910-1A

M15910-2A

M15910-3A

M15910-4A

End Glass Trim Front Black

M15959

EndGlass Trim Stainless (Optional)

M15959-A

End Panel Ass'y Left (color needed)

SA4361-L

End Panel Ass'y Right (color needed)

SA4361-R

Pad 1x1 End Panel (Dual Lock 250)

77-17849

Pad 1x1 Cabinet (Dual Lock 170)

77-17848

ELPRSS PANELS

ELPRSS3

ELPRSS4

ELPRSS5

ELPRSS6

Acrylic End Clear

15-19808

LPRSS SHELVING

LPRSS3

LPRSS4

LPRSS5

LPRSS6

Shelf Top Black

M20969-1

M20969-3

M20969-5

M20969-7

Shelf Bottom Black

M20969-2

M20969-4

M20969-6

M20969-8

Shelf Top Stainless (Optional)

M20969-1A

M20969-3A

M20969-5A

M20969-7A

Shelf Bottom Stainless (Optional)

M20969-2A

M20969-4A

M20969-6A

M20969-8A

Glass Shelf Top (Optional)

52-17991-1

52-17991-2

52-17991-3

52-17991-4

Glass Shelf Bottom (Optional)

52-17992-1

52-17992-2

52-17992-3

52-17992-4

Glass Shelf Retainer(Optional)

SA4091

Shelf Bracket Top

67-17732-1

Shelf Bracket Bottom

67-17732-2

Shelf Standard

M14679-A

ELPRSS SHELVING

ELPRSS3

ELPRSS4

ELPRSS5

ELPRSS6

Shelf Black

M20969-9

M20969-10

M20969-11

M20969-12

Shelf Bracket

67-17732-2

Shelf Standard

M14679-A

LPRSS MISCELLANEOUS OPTIONS

LPRSS3

LPRSS4

LPRSS5

LPRSS6

Page 40

Page 40 of 40

Rear Door Inner Black(Optional)

53-17912-1

53-17912-2

53-17912-3

53-17912-4

Rear Door Outer Black (Optional)

53-17913-1

53-17913-2

53-17913-1

Rear Door Top Track (Optional)

57-17910-1

57-17910-2

57-17910-3

57-17910-4

Rear Door Bottom Track (Optional)

57-17909-1

57-17909-2

57-17909-3

57-17909-4

Rear Door Jamb (Optional)

57-17911

Security Night Cover Panel (Optional)

M16107-1

M16107-2

M16107-3

M16107-4

Security Night Cover Latch (Optional)

66-11727

Night Curtain Black

65-19459

65-19460

65-19458

65-19300

Step Riser Top (Optional)

SA4367-1

SA4367-2

SA4367-3

SA4367-4

Step Riser Bottom (Optional)

SA4367-5

SA4367-6

SA4367-7

SA4367-8

California Residents Only.

WARNING

This product can expose you to chemicals including chromium which is known to the State of California to cause

cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov