Fbii XL-2 SILVER User Manual
N9512 Rev.A 8/95
Quick Reference
TURN SYSTEM ON
Check to make sure the system is READY - Green ready light is lit
Enter your four digit user code
The On/Off (Arm) light will light
Exit through a door designated by your installer as an exitientry door.
TURN SYSTEM OFF
Enter through a door designated by your installer as an exiffenty door,
Enter your four digit user code
The System On (Arm) light will go out
TURN SYSTEM ON AND STAY INSIDE
Check to make sure the system is READY - Green ready light is lit
❑ unn
❑ oon
~
The On/Off (arm) fight and the Stay light will both light
REMEMBER: You must turn the system off if you want to open the door or
leave the premises after the exit time has passed,
TURN THE SYSTEM ON: PERIMETER SENSORS
INSTANT MODE AND STAY INSIDE
Check to make sure the system is READY - Green readv light is tit
~
~
H
The On/Off light, the Instant light and the Stay light will all be on
SMOKE DETECTOR RESET
Enter your four digit user code ❑❑❑❑
ALARM COMPANY SERVICE NUMBER
Followed by your user code
followedby - -
followed by your user code ❑ ❑ ❑ ❑
❑ DDD
Introduction
Congratulations on your decision to protect your home or business wiih the
XL-2S security system. You have chosen a reliable, state of the afl se:urity
system that is remarkably easy to operate. Your system hae been
professionally installed by your local Security Company who can explain
the specifics of your system.
The keypad is the input and display device for your security system. The
following keypad models can interact with your system. Your Security
Company will suggest the model most appropriate for your premises and
your needs.
XL-4600SM — A surface mount keypad containing indicator tights for each
of the 6 zones (areas of protection). The door coveting the buttons is
optional and can be removed.
6805 — Keypad with a plastic case and a two line English read-out LCD
(liquid crystal display). Status messages for the zones (areas of protection)
are displayed in simple English.
The XL-2S is listed by Undemriters Laboratories for Household Rn? and
Burgla~ applications.
Throughout this manual the following conventions are used to display the
keystrokes required to perform the functions.
~ - Button labeled BYPASS
~
~ - Butte” labeled STAY
1 -Button labeled CODE
:
❑ uun
Please keep your manual in a convenient location so you can refer to it if
needed.
- Button labeled INSTANT
- Four digit user code
SYSTEM REFERENCE
ZONE PROTECTED AREA
1
2
3
4
5
6
Entry time
Entry time
USER ID
1
2
3
4
5 Only Turns System On-Yesn Non
6 Ambush/Duress Code -Yesn Non
“Master User can Add, Change, or Erase other user codes.
The following SEND HELP ALERTS are programmed into my system. Both
Buttons must be pressed at the same time to activate the alert.
BUTTONS DESCRIPTION
ASSIGNED TO
Door Exit time
Door
(MASTER USER .)
If No
If No
Leff
Center
Right
Monitoring Station Information
Account #
Telephone #
TU~ING T~ SYSTEM ON
You can turn the Burglar portion of your security system on and off. Before
you turn the system on it must be ready, If you have a protected door c)pen,
or someone is moving by a motion detector the system will not show ready
syetemis ready if the ready light ie on or if the display shows:
The
~
TURN THE SYSTEM ON AND LEAVE
Enter your four digit user code ❑ oon
The System On (Arm) light will go on or the display will show
~
Exit through a door designated by your installer as an exiffent~ door. You
must leave within the period of time known as the exit time. Check the
reference sheet for the time that has been set for your system.
NOT READY
If the system is notready to be armed the READY light will be off and the
Zone lights will show which zone or zones are not ready. The zone lights
indicate the following conditions or the display will show as below:
Fast Btink Alarm
Slow BlinWLow Intensity
Slow Pulse Trouble
SolidOn Not Ready
Bypass
Exemple: If the Ready light is not lit and the zone one light is sofid on.
An alarm sensor on zone one is not normal. This might mean that a window
is open or someone is walking through a motion sensor. Check all sensors
on zone one and resolve the problem. When all sensors are normal the
Ready light will come on and the zone hght will go out.
~splay shows:
~
~
TO TURN THE SYSTEM ON - NOT READY
Determine which zone or zones is not ready, resolve the problem and turn
the system on normally. If the problem cannot be resolved you may bypass
the zone that is not ready. Bypassing should only be done if the problem
on the zone cannot be resolved OR if you intentionally wish to leave the
zone off, Example: you wish to keep the window open for ventilation. Zones
that are bypassed are not protected
for the correct procedure.
whenthesystemison.SeeBypass
TURN SYSTEM ON AND STAY INSIDE
To turn the perimeter potion of your burglar alarm on and move around
freely inside is the STAY mode.
Check to make sure the system is READY when ready press:
~
If successful the On/Off (arm) light will be lit and the Stay tight will also be
lit or the display shows:
ON: STAY
I J
REMEMBER: You must turn the system off if you want to open the door or
leave the premises after the exit time has passed.
FO[lOwed by your user code
❑ oon
TURN THE SYSTEM ON: PERIMETER SENSORS
INSTANT MODE AND STAY INSIDE
In INSTANT STAY mode the perimeter portion of your burglar alarm system
is on and the time delays are ehminated from your normal ent~/exit door(s).
All interior protection is off so you are free to move around inside.
Check to make sure the system is READY, when ready press:
~ followed by
~
B
If successful the On/Off tight, the Instant light and the Stay fight will all be
on or the display shows:
folfowed by your user code
❑ ❑ ❑ ❑
~
BYPASS
Bypass excludes a zone of protection from the security system until it is
unbypasssed unless you have auto-bypassing enabled. Bypassing can only
be done while the syetem is turned off.
Press the Bypass Button followed by your user code and then the Zone #
(1-6) to be bypassed.
-
NOTE: Bypassed zones are not protected when the system is turned on.
After the bypass command has been accepted the keypad will sound one
❑ODD ,ONE
Loading...