Fbii OMNI-408, OMNI-408EU User Manual

6HFXULW\6\VWHP

011,,

220

011,,((88

220

8VHU*XLGH

N9942-2 1/01

TABLE OF CONTENTS (cont’d)

QUICK REFERENCE.....................................3

System Turn On..........................................3

System Turn Off..........................................3

System Turn On/Stay Inside.......................3

System Turn On/Stay Inside/Instant Mode.3

Smoke Detector Reset................................3

INTRODUCTION............................................5

SYSTEM REFERENCE .................................6

SYSTEM OPERATION ..................................9

To Turn the System On and Leave ............9

When the System is Not Ready................10

To Turn the System On and Stay Inside ..10 To Turn the System On In Instant Mode and

Stay Inside................................................11

To Turn the System On In Instant Mode ..12

To Bypass a Zone.....................................12

To Unbypass a Zone ................................13

Turning the System Off.............................13

USER CODES..............................................15

Adding/Changing a User Code.................15

Deleting a User Code ...............................15

PAGING FEATURE .....................................16

Follow-Me Displays .................................. 16

Changing the Pager Follow-Me Phone

Number.....................................................16

KEYPAD FUNCTIONS.................................18

System Turn On (Maid Code)...................18

Send Help Conditions...............................18

Set Time and Date....................................20

Turn Chime On/Off ...................................20

TESTING THE SYSTEM..............................21

System Test..............................................22

Battery Test ..............................................22

RECOMMENDATIONS ON SMOKE

DETECTORS...............................................22

EMERGENCY EVACUATION ......................23

SYSTEM LIMITATIONS...............................26

– 2 –

GLOSSARY..................................................29

Quick Reference

System Turn On

Check to make sure the system is ready — Green READY LED is lit. Enter your 4-digit User Code (or press the ARM button on your keyfob). The ARMED LED goes on. Exit through a door designated by your installer as an exit/entry door.

System Turn Off

Enter through door designated by your installer as an exit/entry door. Enter your 4-digit User Code (or press the DISARM button on your

keyfob). The ARMED LED goes out.

System Turn On/Stay Inside

Check to make sure the system is ready — Green READY LED is lit.

Press

The ARMED and STAY LEDs light.

You must turn the system off if you want to open the door or leave the premises after the exit time has passed.

System Turn On/Stay Inside/Instant Mode

Check to make sure the system is ready — Green READY LED is lit.

Press

The ARMED, INSTANT, and STAY LEDs are all lit.

Smoke Detector Reset

Enter your 4-digit User Code.

STAY

INSTANT

followed by your User Code.

then

STAY

followed by your User Code.

– 3 –

Quick Reference (cont’d)

The following table lists the “Quick Commands” available with this control

Keystroke Quick Command Keypads

[BYPASS] + Zone No.

Quick Arm All keypads If system is ready, allows you to arm the system without

Force Arm All keypads Allows you to arm the system even i f some zones are

Quick Bypass All keypads

Set Time All keypads

Zone Directory LCD only Displays listing of zones in system.

Display Firmware Version LCD only Displays version of your OMNI-408 firmware.

Display Keyfob Battery Status All keypads Allows you to test battery status of your keyfob. Upon entry

Change/View Pager Number All keypads Allows you to redirect pager output to a different pager

Display/Toggle Chime Mode All keypads Allows you to change the status of the chime function.

Display Current Time LCD only Allows you to view the current system time.

Description

requiring your User Code. Your User Code is always needed to disarm the system.

faulted. These zones are automatically bypassed and are unprotected.

Allows you to bypass a specific zone number. Must be enabled by yo ur inst al ler.

Allows entry of the current system time (hours, minutes, month, day, year).

of this mode, press any button on the keyfob and the keypad will display if your battery is low.

number. Phone numbers are displayed only on LCD keypads.

– 4 –

User Page Toggle All keypads Allows you to turn the pager mode on or off. Keypad

displays the current s ystem status.

Introduction

Congratulations on your decision to protect your home or business with the OMNI-408 security system. You have chosen a reliable, state-of-the-ar t secu rity system that i s rema rkably easy to operate. Representatives from your local security company, who can explain the specifics of your system, have professionally installed your system.

The keypad is the input and display device for your security system. Your system can use either the OMNI-KP, OMNI-LCD or OMNI-LED keypads. The OMNI-KP keypad displays the system status with fixed words, the OMNI-LCD keypad displays two lines of text, and the OMNI-LED keypad displays the current zone status, including alarms, bypasses, and f a ults, using LEDs. Each condition causes the LEDs to operate differently.

Throughout this guide, the following conventions are used to display the keystrokes required to perform functions.

BYPASS

INSTANT

STAY

CODE

Please keep your guide in a convenient location so you can refer to it if needed.

Key labeled [BYPASS] Key labeled [INSTANT] Key labeled [STAY] Key labeled [CODE]

Enter your four-digit User Code.

– 5 –

System Reference

ZONE DESCRIPTION

1 2 3 4 5 6 7 8

ENTRY TIME 1 DOOR

ENTRY TIME 2

DOOR

EXIT

TIME*

* Exit time is the same for all designated entry/exit doors. The following SEND HELP ALERTS can be programmed into your

system. Both keys must be pressed at the same time to activate the alert. The keys you press depend on which type of keypad you have. Your installer will show you how to activate these emergency keys.

DESCRIPTION KEYS

[#] and [*] [7] and [9] [1] and [3]

See page 7 of this User Guide for pictures of the OMNI-KP, OMNI-LCD, and OMNI-LED keypads.

– 6 –

OMNI-KP KEYPAD

System Reference (cont’d)

ARMED

READY

STAY

BYPASS

INSTANT

CODE

1 4 7

2 5 8 0

3 6 9 #

OMNI-LCD AND OMNI-LED KEYPADS

ARM AC / LB

READY

ARMED

READY

STAY

BYPASS

INSTANT

CODE

OMNI-LCD Alpha Keypad

1 4 7

OMNI_LCD

STAY

INST TX LB

RF. SPRV.

1 3

4 6

7 9

8 0

STAY

BYPASS

INSTANT

OMNI-LED Keypad

CODE

OMNI_LED

– 7 –

System Reference (cont’d)

USER ID ASSIGNED TO

1 (MASTER USER 1) 2 3 4 5 6 Duress**

* The Master User can add, change, or erase other User Codes. ** If enabled, this User Code will transmit a duress signal to the central station.

MONITORING STATION INFORMATION

Account No. Telephone No.

– 8 –

System Operation

You can turn the burglar portion of your security system on and off. Before you can turn the system on, it must be “ready.” If you have a protected door open, or if someone is moving in view of a motion detector, the system will not display “

The system is ready if the READY LED is lit and the display shows:

System Operation

READY

.”

LCD Keypad:

SYSTEM READY

NOTE:

If programmed by your installer, you may arm the system if a

Fixed-Word Keypad:

READY LED lit

delay or interior zone is faulted. However, faulted zones must be restored before your exit time expires or an alarm or zone bypass will result. Ask your installer if your system has this feature and, if so, if it causes an alarm or zone bypass.

To Turn the System On and Leave

Enter your User Code. The

ARMED

LCD Keypad:

ON: AWAY

LED goes on an d the display shows:

Fixed-Word Keypad:

ARMED LED lit

Exit through a door designated by your installer as an exit/entry door. You must leave within the exit time programmed by your installer. Refer to the reference sheet for the time that has been set for your system.

– 9 –

System Operation (cont’d)

When the System is Not Ready

If the system is display indicates which zone or zones are not ready.

Determine which zone or zones are not ready, resolve the problem, and turn the system on normally. If the problem cannot be resolved, you may bypass the zone that is not ready. Bypassing should only be done if the problem on the zone cannot be resolved, OR if you intentionally wish to leave the zone off. For example, you would leave the zone off if you plan to keep the window open for ventilation. Zones that are bypassed are not protected when the system is on. Refer to the paragraph entitled, “To Bypass a Zone” for a description of the procedure.

To Turn the System On and Stay Inside

To turn the perimeter portion of your burglar alarm on and move around freely inside the premises, use the

Check to make sure the system is ready. When it is ready, press:

STAY

When the system has been turned on successfully, the ARMED LED is on, and the following is displayed:

ready to be armed, the READY LED is

not

STAY

followed by your User Code.

mode.

off

and the

– 10 –

LCD Keypad:

ON: STAY

REMEMBER:

door or leave the premises after the exit time has passed.

You must turn the system off if you want to open the

Fixed-Word Keypad:

STAY

+ 22 hidden pages