Fastron Parts VISION Series General Manual
VISION Series
Vertical Oven Controller
with Shelf ID
231-60230-03
Programming Guide
Toll-Free Technical Support
24 Hours A Day, 365 Days A Year
(from the U.S., Canada and the Caribbean)
1-800-243-9271
This document contains confidential
information. The dissemination, publication,
copying, or duplication of this document or
the software described herein without prior
written authorization is strictly prohibited.
w
w
w
.
f
a
s
t
i
n
c
m
.
o
c
F
-
0
0
8
-
1
the time is right.
N
O
R
T
S
A
$5.00 USD
Important Notices
FAST is not liable for any use
of product not in accordance
with its installation and operating
instructions.
Before using this equipment, or
for any questions on the operation of the appliance, consult and
follow all instructions and safety
warnings found in the appliance
operator’s manual supplied from
the manufacturer of the appliance.
Not all features are available on
some models.
Controller Operating Environment
Cleaning the Controller
Using a clean damp cloth, wipe down your
controller daily.
Do not allow oil to build up on any part of the
controller.
NEVER use chemical or abrasive cleaners
on your controller. The controller’s overlay
may be damaged.
The solid state components in this controller are
designed to operate reliably in a temperature range
up to 158°F/ 70°C. Before installing this controller,
it should be verified that the ambient temperature
at the mounting location does not exceed 158°F/
70°C.
This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited.
2
Vision Vertical Oven Controller
www.fastinc.com 1-800-243-9271
229-51337D © 2007-2010 FAST
Programming the Controller
Recipe Programming—1724
Entering Programming and Changing Recipes
Press and hold the “P” for 3 seconds.
Product Cnt will be displayed. Press the down
arrow.
Programming will be displayed, then press the “P”
key.
ENTER CODE will be displayed.
From ENTER CODE, type in 1724, then press the “P”
key.
Display will show RECIPE. Press the “P” key and all
product LEDs will light up and the display will
read Select Product To Program.
Press the Product key you would like to program.
NOTE: Some controls have different options
than what are listed.
ALL will be displayed.
NOTE: Depending on the model of the unit,
you can either press the “P” key to change
all of the programmable settings or you can
scroll using the arrow Up or Down keys to
any of the specific options.
Stage X Temp will be displayed with the current set
temp XXXF. To change temperature, type in your
new temperature. Then press the “P” key.
Stage X Timing will be displayed, then either
STRAIGHT, FLEX or SENSITIVITY. Use the left or right
arrow keys to change between the 3 settings.
Then press the “P” key.
Stage X Sens will be displayed with the current
sensitivity setting 0-9. To change the sensitivity
setting, type in your new setting. Then press the
“P” key.
Stage X Fan Spd will be displayed, then either HIGH
or LOW. Use the left or right arrow keys to change
between the 2 settings. Then press the “P” key.
Stage X Fan Cyc will be displayed, then either FULL,
HEAT, or PULSE. Use the left or right arrow keys to
change between the 3 settings. Then press the
“P” key.
If PULSE is selected:
Stage X Fan ON will be displayed with the current
time XX:XX. To change the Fan ON time, type in a
new time. Then press the “P” key.
Stage X Fan OFF will be displayed with the current
time XX:XX. To change the Fan OFF time, type in a
new time. Then press the “P” key
From ALL being displayed press the “P” key.
Product Name will be displayed. To scroll through
the Library, use the arrow Up or Down keys or
you can use the letters on each key to start a
word from the Library. Once you have chosen
your word, press the “P” key.
Shelf Cook NO will be displayed. Use the Left or
Right arrow keys to change from YES or NO for
Shelf Cook. Then press the “P” key. NOTE: If YES
is selected, you will not be given an option for
extra stages.
Stage X Time will be displayed with the current set
time XX:XX. To change, type in a new time, then
press the “P” key.
This document contains confidential information. The dissemination, publication, copying, or duplication of this document or the software described herein without prior written authorization is strictly prohibited.
Vision Vertical Oven Controller
www.fastinc.com 1-800-243-9271
NOTE: Each product key can be
programmed with up to 10 stages. If no
additional stages are required, set the time
to zero, and press the “P” key to continue
to Alarm Time.
Alarm X Time will be displayed with the current
time XX:XX. To change the alarm time, type in a
new time. Then press the “P” key.
Alarm X Name will be displayed with the current
name. To scroll through the Library, use the arrow
Up or Down keys or you can use the letters on
each key to start a word from the Library. Once
you have chosen your word, press the “P” key.
Alarm X Done will be displayed along with either
AUTOMATIC or MANUAL. Use the left or right arrow
keys to change between the 2 settings. Then
press the “P” key.
229-51337D © 2007-2010 FAST
3
Loading...