FANVIL FANVIL I31S User guide

Download

[键入文字]

i31S IP Video DoorPhone

User Manual V2.0

[键入文字]

Document VER

Firmware VER

Explanation

Time

V1.0

2.1.1.2898

Initial issue

20170629

V2.0

2.1.1.2898

Change company address and add IP scan tool download

address in QIG

20171027

[键入文字]

Safety Notices

1. Please use the specified power adapter. If you need to use the power adapter provided by other

manufacturers under special circumstances, please make sure that the voltage and current provided is

in accordance with the requirements of this product, meanwhile, please use the safety certificated

products, otherwise may cause fire or get an electric shock.

2. When using this product, please do not damage the power cord either by forcefully twist it, stretch

pull, banding or put it under heavy pressure or between items, otherwise it may cause damage to the

power cord, lead to fire or get an electric shock.

3. Before using, please confirm that the temperature and environment is humidity suitable for the

product to work. (Move the product from air conditioning room to natural temperature, which may

cause this product surface or internal components produce condense water vapor, please open power

use it after waiting for this product is natural drying).

4. Please do not let non-technical staff to remove or repair. Improper repair may cause electric shock,

fire, malfunction, etc. It will lead to injury accident or cause damage to your product.

5. Do not use fingers, pins, wire, other metal objects or foreign body into the vents and gaps. It may

cause current through the metal or foreign body, which may even cause electric shock or injury

accident. If any foreign body or objection falls into the product please stop using.

6. Please do not discard the packing bags or store in places where children could reach, if children trap

his head with it, may cause nose and mouth blocked, and even lead to suffocation.

7. Please use this product with normal usage and operating, in bad posture for a long time to use this

product may affect your health.

8. Please read the above safety notices before installing or using this phone. They are crucial for the safe

and reliable operation of the device.

[键入文字]

I Product introduction

i31S voice access is a full digital network door phone, with its core part adopts mature VoIP

solution (Broadcom chip), stable and reliable performance, hands-free adopting digital full-duplex

mode, voice loud and clear, generous appearance, solid durable, easy for installation,

comfortable keypad and low power consumption.

i31S voice access supports entrance guard control, voice intercom, ID card and keypad remote

to open the door.

1. Appearance of the product

2. Description

[键入文字]

7/54

Lock Status

Door unlocking: On

Door locking: Off

Call status

Standby: Off

Call Holding: Blink with 1s

Calls: On

Ring status

Standby: Off

Ringing: On

Network/SIP

Registration

Network error: Blink with 1s

Network running: Off

Registration failed: Blink with 3s

Registration succeeded: On

CN7

1234567

+12V

VSS

COM

S_IN

S_OUT

12V 1A/DC

Electric-lock switch

Indoor switch

Jumper in passive mode Jumper in active mode

II Start Using

Before you start to use the equipment, please make the following installation.

1. Confirm the connection

Confirm whether the equipment of the power cord, network cable, electric lock control line

connection and the boot-up is normal. (Check the network state of light)

Power, Electric Lock, Indoor switch port

Voice access the power supply ways: 12v/DC or POE.

Driving mode of electric-lock(Default in Passive mode)

[键入文字]

8/54

Driving Mode

Electric lock

Jumper port

Connections

Active

Passive

No electricity

when open

When the

power to open

√

【Note】When the device is in active mode, it can drive 12V/650mA switch output maximum, to which a

standard electric-lock or another compatible electrical appliance can be connected.

 When using the active mode, it is 12V DC in output.  When using the passive mode, output is short control (normally open mode or normally close mode).

3) Wiring instructions

 NO: Normally Open Contact.  COM: Common Contact.  NC: Normally Close Contact.

[键入文字]

9/54

√

2. Quick Setting

The product provides a complete function and parameter setting. Users may need to have the

network and SIP protocol knowledge to understand the meaning represented by all parameters. In

order to let equipment users enjoy the high quality of voice service and low cost advantage brought by

the device immediately, here we list some basic but compulsory setting options in this section to let

users know how to operate without understanding such complex SIP protocols.

In prior to this step, please make sure your broadband Internet online can be normal operated,

and complete the connection of the network hardware. The product factory default network mode is

DHCP. Thus, only connect equipment with DHCP network environment that network can be

automatically connected.



Press and hold “#” key for 3 seconds and the door phone will report the IP address by voice, or use

the "iDoorPhoneNetworkScanner.exe" software to find the IP address of the device.

(Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe )



Note: when power on, 30s waiting is needed for device running.



Log on to the WEB device configuration.



In a Line page configuration service account, user name, parameters that are required for server

address register.



You can set DSS key in the Function key page.



You can set Door Phone parameters in the Webpage (EGS Setting-> Features).

[键入文字]

10/54

III Basic operation

1. Answer a call

When a call comes in, the device will answer automatically. If you cancel auto answer feature and set

auto answer time, you will hear the bell ring at the set time and the device will auto answer after a

timeout.

2. Call

Configure shortcut key as hot key and setup a number, then press shortcut key can call the

configured number.

3. End call

Enable Release key hang up to end call.

4. Open the door operation

Through the following seven ways to open the door:

1) Input password on the keyboard to open the door.

2) Access to call the owner and the owner enter the remote password to open the door.

3) Owner/other equipment call the access control and enter the access code to open the door. (access

code should be included in the list of access configuration, and enable for remote calls to open the

door)

4) Swipe the RFID cards to open the door.

5) By means of indoor switch to open the door.

6) Private access code to open the door.

Enable for local authentication, and set private access code. Input the access code directly under

standby mode to open the door. In this way, the door log will record corresponding card number

and user name.

7) Active URL control command to open the door.

URL is “http://user:pwd@host/cgi-bin/ConfigManApp.com?key=F_LOCK&code=openCode”

a. User and pwd is Web the user name and password.

b. “openCode” is the remote control code to open the door.

Example: “http://admin:admin@172.18.3.25/cgi-bin/ConfigManApp.com?key=*”

If access code is input correctly, the device will play sirens sound to prompt access control and the

remote user, while input error by low-frequency short chirp.

Password input successfully followed by high-frequency sirens sound, while input error is followed by

[键入文字]

11/54

high-frequency short chirp.

When door has been opened, the device will play sirens sound to prompt.

IV Page settings

1. Browser configuration

When the device and your computer are successfully connected to the network, enter the IP

address of the device on the browser as http://xxx.xxx.xxx.xxx/ and you can see the login interface of

the web page management.

Enter the user name and password and click the [logon] button to enter the settings screen.

2. Password Configuration

There are two levels of access: root level and general level. A user with root level access can

browse and set all configuration parameters, while a user with general level can set all configuration

parameters except server parameters for SIP.

 Default user with general level: The default is not set, are free to add.  Default user with root level:

 User name: admin  Password: admin

[键入文字]

12/54

Information

Field Name

Explanation

System

Information

Display equipment model, hardware version, software version, uptime, Last uptime

and MEMinfo.

Network

Shows the configuration information for WAN port, including connection mode of WAN

port (Static, DHCP, PPPoE), MAC address, IP address of WAN port.

SIP Accounts

Shows the phone numbers and registration status for the 2 SIP LINES.

3. Configuration via WEB

(1) System

a) Information

[键入文字]

13/54

Account

Field Name

Explanation

Change Web Authentication Password

You Can modify the login password to the account

Add New User

You can add new user

User Accounts

Show the existing user information

b) Account

Through this page, user can add or remove users depends on their needs and can modify existing user

permission.

[键入文字]

14/54

Configurations

Field Name

Explanation

Export

Configurations

Save the equipment configuration to a txt or xml file. Please note to Right click on

the choice and then choose “Save Link As.”

Import

Configurations

Browse to the config file, and press Update to load it to the equipment.

Reset to factory

defaults

This will restore factory default and remove all configuration information.

Upgrade

Field Name

Explanation

Software upgrade

Browse to the firmware, and press Update to load it to the equipment.

c) Configurations

d) Upgrade

e) Auto Provision

[键入文字]

15/54

Auto Provision

Field Name

Explanation

Common Settings

Current

Configuration

Version

Show the current config file’s version. If the version of configuration downloaded

is higher than this, the configuration will be upgraded. If the endpoints confirm

the configuration by the Digest method, the configuration will not be upgraded

unless it differs from the current configuration

General

Configuration

Version

Show the common config file’s version. If the configuration downloaded and this

configuration is the same, the auto provision will stop. If the endpoints confirm

the configuration by the Digest method, the configuration will not be upgraded

unless it differs from the current configuration.

CPE Serial Number

Serial number of the equipment

Authentication

Name

Username for configuration server. Used for FTP/HTTP/HTTPS. If this is blank the

phone will use anonymous

Authentication

Password

Password for configuration server. Used for FTP/HTTP/HTTPS.

Configuration File

Encryption Key

Encryption key for the configuration file

General

Configuration File

Encryption Key

Encryption key for common configuration file

Save Auto Provision

Save the auto provision username and password in the phone until the server url

[键入文字]

16/54

Information

changes

DHCP Option

Option Value

The equipment supports configuration from Option 43, Option 66, or a Custom

DHCP option. It may also be disabled.

Custom Option

Value

Custom option number. Must be from 128 to 254.

SIP Plug and Play (PnP)

Enable SIP PnP

If this is enabled, the equipment will send SIP SUBSCRIBE messages to a multicast

address when it boots up. Any SIP server understanding that message will reply

with a SIP NOTIFY message containing the Auto Provisioning Server URL where

the phones can request their configuration.

Server Address

PnP Server Address

Server Port

PnP Server Port

Transportation

Protocol

PnP Transfer protocol – UDP or TCP Update Interval

Interval time for querying PnP server. Default is 1 hour.

Static Provisioning Server

Server Address

Set FTP/TFTP/HTTP server IP address for auto update. The address can be an IP

address or Domain name with subdirectory.

Configuration File

Name

Specify configuration file name. The equipment will use its MAC ID as the config

file name if this is blank.

Protocol Type

Specify the Protocol type FTP, TFTP or HTTP.

Update Interval

Specify the update interval time. Default is 1 hour.

Update Mode

1. Disable – no update

2. Update after reboot – update only after reboot.

3. Update at time interval – update at periodic update interval

TR069

Enable TR069

Enable/Disable TR069 configuration

ACS Server Type

Select Common or CTC ACS Server Type.

ACS Server URL

ACS Server URL.

ACS User

User name for ACS.

ACS Password

ACS Password.

TR069 Auto Login

Enable/Disable TR069 Auto Login.

INFORM Sending

Period

Time between transmissions of “Inform” Unit is seconds.

f)FDMS

[键入文字]

17/54

FDMS Settings

Enable FDMS

Enable/Disable FDMS configuration

FDMS Interval

The time to send sip Subscribe information to the FDMS server on a regular basis.

Unit seconds

Doorphone Info Settings

Community Name

The name of the community where the device is installed

Building Number

The name of the building where the equipment is installed

Room Number

The name of the room where the equipment is installed

f) Tools

Syslog is a protocol used to record log messages using a client/server mechanism. The Syslog server

[键入文字]

18/54

Tools

Field Name

Explanation

Syslog

Enable Syslog

Enable or disable system log.

Server Address

System log server IP address.

Server Port

System log server port.

APP Log Level

Set the level of APP log.

SIP Log Level

Set the level of SIP log.

Network Packets Capture

Capture a packet stream from the equipment. This is normally used to troubleshoot problems.

Reboot Phone

Some configuration modifications require a reboot to become effective. Clicking the Reboot button will

lead to reboot immediately.

Note: Be sure to save the configuration before rebooting.

receives the messages from clients, and classifies them based on priority and type. Then these messages

will be written into a log by rules which the administrator has configured.

There are 8 levels of debug information.

Level 0: emergency; System is unusable. This is the highest debug info level.

Level 1: alert; Action must be taken immediately.

Level 2: critical; System is probably working incorrectly.

Level 3: error; System may not work correctly.

Level 4: warning; System may work correctly but needs attention.

Level 5: notice; It is the normal but significant condition.

Level 6: Informational; It is the normal daily messages.

Level 7: debug; Debug messages normally used by system designer. This level can only be displayed

via telnet.

(2) Network

[键入文字]

19/54

Field Name

Explanation

Network Status

The current IP address of the equipment

Subnet mask

The current Subnet Mask

Default gateway

The current Gateway IP address

MAC

The MAC address of the equipment

MAC Timestamp

Get the MAC address of time.

Settings

Select the appropriate network mode. The equipment supports three network modes:

Static IP

Network parameters must be entered manually and will not change. All parameters

are provided by the ISP.

DHCP

Network parameters are provided automatically by a DHCP server. PPPoE

Account and Password must be input manually. These are provided by your ISP.

If Static IP is chosen, the screen below will appear. Enter values provided by the ISP.

DNS Server

Configured by

Select the Configured mode of the DNS Server.

Primary DNS

Server

Enter the server address of the Primary DNS.

Secondary DNS

Server

Enter the server address of the Secondary DNS.

a) Basic

[键入文字]

20/54

After entering the new settings, click the APPLY button. The equipment will save the new settings and

apply them. If a new IP address was entered for the equipment, it must be used to login to the phone

after clicking the APPLY button.

Service Port Settings

Web Server Type

Specify Web Server Type – HTTP or HTTPS

HTTP Port

Port for web browser access. Default value is 80. To enhance security, change this

from the default. Setting this port to 0 will disable HTTP access.

Example: The IP address is 192.168.1.70 and the port value is 8090, the accessing

address is http://192.168.1.70:8090.

HTTPS Port

Port for HTTPS access. Before using https, an https authentication certification must

be downloaded into the equipment.

Default value is 443. To enhance security, change this from the default.

Note:

1) Any changes made on this page require a reboot to become active.

2) It is suggested that changes to HTTP Port be values greater than 1024.Values less than 1024 are

reserved.

3) If the HTTP port is set to 0, HTTP service will be disabled.

b) VPN

The device supports remote connection via VPN. It supports both Layer 2 Tunneling Protocol (L2TP)

and OpenVPN protocol. This allows users at remote locations on the public network to make secure

connections to local networks.

[键入文字]

21/54

[键入文字]

22/54

Field Name

Explanation

VPN IP Address

Shows the current VPN IP address.

VPN Mode

Enable VPN

Enable/Disable VPN.

L2TP

Select Layer 2 Tunneling Protocol

OpenVPN

Select OpenVPN Protocol. (Only one protocol may be activated. After the selection

is made, the configuration should be saved and the phone be rebooted.)

Layer 2 Tunneling Protocol (L2TP)

L2TP Server

Address

Set VPN L2TP Server IP address.

Authentication

Name

Set User Name access to VPN L2TP Server.

Authentication

Password

Set Password access to VPN L2TP Server.

Open VPN Files

Upload or delete Open VPN Certification Files

(3) Line

a) SIP

Configure a SIP server on this page.

[键入文字]

23/54

[键入文字]

24/54

SIP

Field Name

Explanation

Basic Settings (Choose the SIP line to configured)

Line Status

Display the current line status at page loading. To get the up to date line status,

user has to refresh the page manually.

Username

Enter the username of the service account.

Display name

Enter the display name to be sent in a call request.

Authentication Name

Enter the authentication name of the service account

Authentication

Password

Enter the authentication password of the service account Activate

Whether the service of the line should be activated

SIP Proxy Server Address

Enter the IP or FQDN address of the SIP proxy server

SIP Proxy Server Port

Enter the SIP proxy server port, default is 5060

Outbound proxy address

Enter the IP or FQDN address of outbound proxy server provided by the service

provider

Outbound proxy port

Enter the outbound proxy port, default is 5060

Realm

Enter the SIP domain if requested by the service provider

Codecs Settings

Set the priority and availability of the codecs by adding or remove them from the list.

Advanced Settings

Subscribe For Voice

Message

Enable the device to subscribe a voice message waiting notification, if enabled,

the device will receive notification from the server if there is voice message

waiting on the server

Voice Message Number

Set the number for retrieving voice message

Voice Message

Subscribe Period

Set the interval of voice message notification subscription

Enable DND

Enable Do-not-disturb, any incoming call to this line will be rejected

automatically

Blocking Anonymous

Call

Reject any incoming call without presenting caller ID

Use 182 Response for

Call waiting

Set the device to use 182 response code at call waiting response

Anonymous Call

Standard

Set the standard to be used for anonymous Dial Without Registered

Set call out by proxy without registration

Click To Talk

Set Click To Talk

User Agent

Set the user agent, the default is Model with Software Version.

[键入文字]

25/54

Response Single Codec

If setting enabled, the device will use single codec in response to an incoming

call request

Ring Type

Set the ring tone type for the line

Conference Type

Set the type of call conference, Local=set up call conference by the device itself,

maximum supports two remote parties, Server=set up call conference by dialing

to a conference room on the server

Server Conference

Number

Set the conference room number when conference type is set to be Server Transfer Timeout

Set the timeout of call transfer process

Enable Long Contact

Allow more parameters in contact field per RFC 3840

Use Quote in Display

Name

Whether to add quote in display name

Use Feature Code

When this setting is enabled, the features in this section will not be handled by

the device itself but by the server instead. In order to control the enabling of the

features, the device will send feature code to the server by dialing the number

specified in each feature code field.

Specific Server Type

Set the line to collaborate with specific server type

Registration Expiration

Set the SIP expiration interval

Use VPN

Set the line to use VPN restrict route

Use STUN

Set the line to use STUN for NAT traversal

Convert URI

Convert not digit and alphabet characters to %hh hex code

DTMF Type

Set the DTMF type to be used for the line

DTMF SIP INFO Mode

Set the SIP INFO mode to send ‘*’ and ‘#’ or ‘10’ and ‘11’

Transportation Protocol

Set the line to use TCP or UDP for SIP transmission

Local Port

Set the Local Port

SIP Version

Set the SIP version

Caller ID Header

Set the Caller ID Header

Enable Strict Proxy

Enables the use of strict routing. When the phone receives packets from the

server, it will use the source IP address, not the address in via field.

Enable user=phone

Sets user=phone in SIP messages.

Enable SCA

Enable/Disable SCA (Shared Call Appearance )

Enable BLF List

Enable/Disable BLF List

Enable DNS SRV

Set the line to use DNS SRV which will resolve the FQDN in proxy server into a

service list

Keep Alive Type

Set the line to use dummy UDP or SIP OPTION packet to keep NAT pinhole

opened

Keep Alive Interval

Set the keep alive packet transmitting interval

[键入文字]

26/54

Enable Session Timer

Set the line to enable call ending by session timer refreshment. The call session

will be ended if there is not new session timer event update received after the

timeout period

Session Timeout

Set the session timer timeout period

Enable Rport

Set the line to add rport in SIP headers

Enable PRACK

Set the line to support PRACK SIP message

Enable DNS SRV

Set the line to use DNS SRV which will resolve the FQDN in proxy server into a

service list

Auto Change Port

Enable/Disable Auto Change Port

Keep Authentication

Keep the authentication parameters from previous authentication

Auto TCP

Using TCP protocol to guarantee usability of transport for SIP messages above

1500 bytes

Enable Feature Sync

Feature Sycn with server

Enable GRUU

Support Globally Routable User-Agent URI (GRUU)

BLF Server

The registered server will receive the subscription package from ordinary

application of BLF phone.

Please enter the BLF server, if the sever does not support subscription package,

the registered server and subscription server will be separated.

BLF List Number

BLF List allows one BLF key to monitor the status of a group. Multiple BLF lists

are supported.

SIP Encryption

Enable SIP encryption such that SIP transmission will be encrypted

SIP Encryption Key

Set the pass phrase for SIP encryption

RTP Encryption

Enable RTP encryption such that RTP transmission will be encrypted

RTP Encryption Key

Set the pass phrase for RTP encryption

b) Basic Settings

STUN -Simple Traversal of UDP through NAT -A STUN server allows a phone in a private network to

know its public IP and port as well as the type of NAT being used. The equipment can then use this

information to register itself to a SIP server so that it can make and receive calls while in a private

network.

[键入文字]

27/54

Basic Settings

Field Name

Explanation

SIP Settings

Local SIP Port

Set the local SIP port used to send/receive SIP messages.

Registration Failure

Retry Interval

Set the retry interval of SIP REGISTRATION when registration failed.

Enable Strict UA

Match

Enable or disable Strict UA Match

STUN Settings

Server Address

STUN Server IP address

Server Port

STUN Server Port – Default is 3478.

[键入文字]

28/54

Binding Period

STUN blinding period – STUN packets are sent at this interval to keep the NAT

mapping active.

SIP Waiting Time

Waiting time for SIP. This will vary depending on the network.

TLS Certification File

Upload or delete the TLS certification file used for encrypted SIP transmission.

Note: the SIP STUN is used to achieve the SIP penetration of NAT, is the realization of a service, when the

equipment configuration of the STUN server IP and port (usually the default is 3478), and select the Use

Stun SIP server, the use of NAT equipment to achieve penetration.

Import Dial peer Table

Field Name

Explanation

Select File

Select an existing dialing rule file. The file type must be a .CSV

Add Dial Peer

Number

In order to add an outgoing call number, the outgoing call number can be divided

into two types: one is the exact match, and after the exact match, if the number is

exactly the same as the user dialing the called number, the device will use the IP

address of this number mapping or (This is the area code prefix function of the

PSTN). If the number matches the N-bit (prefix number length) of the called

number, the device uses the IP address or configuration mapped to this number.

Make a call. Configuration prefix matching needs to be followed by a prefix

number to match the exact match number; the longest support of 30 bits; also

supports the use of x format and range of numbers.

C) Dial Peer

Configure the Dial Peer to make the device call more flexible.

[键入文字]

29/54

Destination

Configure the destination address and, if configured as a point-to-point call, write

the peer IP address directly. Can also be set to domain name, by the device DNS

server to resolve the specific IP address. If it is not configured, the IP address is

0.0.0.0. This is an optional configuration item

Port

Configure the signaling port of the other party. This is an optional configuration

item. The default is 5060

Alias

Configure aliases, this is an optional item: the replacement number used when

the prefix is prefixed, and no alias when configured

Note: aliases are divided into four types and must be combined with the replacement length:

1) add: xxx, add xxx before the number. This can help users save dialing length;

2) all: xxx, all replaced by xxx; can achieve speed dial, such as user configuration dial-up 1, then by

configuring all: number to change the actual call out the number;

3) del, delete the number before the n bit, n by the replacement length set;

4) rep: xxx, the number n before the number is replaced by xxx, n is set by the replacement length. For

example, if the user wants to dial the PSTN (010-62281493) through the floor service provided by the

VoIP operator, and the actual call should be 010-62281493, then we can configure the called number 9T,

then rep: 010, and then delete the length Set to 1. Then all users call the 9 at the beginning of the phone

will be replaced with 010 + number sent. To facilitate the user to call the habit of thinking mode;

Call Mode

Configuration selection of different signaling protocols, SIP;

Suffix

Configure the suffix, this is optional configuration items: that is, after the dial-up

number to add this suffix, no configuration shows no suffix;

Deleted Length

Configure the replacement / delete length, the number entered by the user is

replaced / deleted by this length; this is an optional configuration item;

(4) EGS Setting

a) Features

[键入文字]

30/54

Features

Field Name

Explanation

Common Settings

Switch Mode

Monostable: there is only one fixed action status for door unlocking.

Bistable: there are two actions and statuses, door unlocking and door locking.

Each action might be triggered and changed to the other status. After

changed, the status would be kept.

Initial Value is Monostable

Switch-On Duration

Door unlocking time for Monostable mode only. If the time is up, the door

would be locked automatically. Initial Value is 5 seconds.

[键入文字]

31/54

Enable Card Reader

Enable or disable card reader for RFID cards.

Card Reader Working

Mode

Set ID card stats:

Normal: This is the work mode, after the slot card can to open the door.

Card Issuing: This is the issuing mode, after the slot card can to add ID cards.

Card Revoking: This is the revoking mode, after the slot card can to delete ID

cards.

Limit Talk Duration

If enabled, calls would be forced ended after talking time is up.

Talk Duration

The call will be ended automatically when time up. Initial Value is 120 seconds

Remote Password

Remote door unlocking password. Initial Value is “*”.

Local password

Local door unlocking password via keypad, the default password length is 4.

Initial Value is “6789”.

APP Door Open

Enable or disable the APP Door Open

APP password

APP door unlocking password. Initial Value is “*”.

Enable Indoor Open

Enable or disable to use indoor switch to unlock the door.

Enable Access Table

Enable Access Table: enter <Access Code> for opening door during calls.

Disable Access Table: enter <Remote Password> for opening door during calls.

Default Enable.

Description

Device description displayed on IP scanning tool software. Initial Value is “i31S

IP Door Phone”.

Enable Open Log

Server

Enable or disable to connect with log server

Address of Open Log

Server

Log server address(IP or domain name)

Port of Open Log

Server

Log server port (0-65535) , Initial Value is 514.

Door Unlock Indication

Indication tone for door unlocked. There are 3 type of tone: silent/short

beeps/long beeps.

Remote Code Check

Length

The remote access code length would be restricted with it. If the input access

code length is matched with it, system would check it immediately. Initial

Value is 4.

Basic Settings

Enable DND

DND might be disabled phone for all SIP lines, or line for SIP individually. But

the outgoing calls will not be affected

Ban Outgoing

If enabled, no outgoing calls can be made.

Enable Intercom Mute

If enabled, mutes incoming calls during an intercom call.

Enable Intercom

Ringing

If enabled, plays intercom ring tone to alert to an intercom call.

[键入文字]

32/54

Enable Auto Dial Out

Auto Dial Out Time

Set Auto Dial Out Time

Enable Auto Answer

Enable Auto Answer function

Auto Answer Timeout

Set Auto Answer Timeout

No Answer Auto

Hangup

Enable automatically hang up when no answer Auto Hangup Timeout

Configuration in a set time, automatically hang up when no answer

Dial Fixed Length to

Send

Enable or disable dial fixed length to send.

Send length

The number will be sent to the server after the specified numbers of digits are

dialed.

Dial Number Voice Play

Configuration Open / Close Dial Number Voice Play

Voice Play Language

Set language of the voice prompt

Enable Delay Start

Enable or disable the start delay

Delay Start Time

Set start delay time

Voice Read IP

Enable or disable voice broadcast IP address

Press "*" to Send

Enable or disable the Press "*" to Send, Initial Value is enable

Block Out Settings

Add or delete blocked numbers – enter the prefix of numbers which should not be dialed by the phone.

For example, if 001 is entered, the phone would not dial any number beginning with 001.

X and x are wildcards which match single digit. For example, if 4xxx or 4XXX is entered, the phone would

not dial any 4 digits numbers beginning with 4. It would dial numbers beginning with 4 which are longer

or shorter than 4 digits.

b) Audio

This page configures audio parameters such as voice codec, speak volume, mic volume and ringer

volume.

[键入文字]

33/54

Audio Setting

Field Name

Explanation

First Codec

The first codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB

Second Codec

The second codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, None

Third Codec

The third codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, None

Fourth Codec

The forth codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, None

DTMF Payload Type

The RTP Payload type that indicates DTMF. Default is 101

Default Ring Type

Ring Sound – There are 9 standard types and 3 User types.

G.729AB Payload

Length

G.729AB Payload Length – Adjusts from 10 – 60 mSec. Tone Standard

Configure tone standard area.

G.722 Timestamps

Choices are 160/20ms or 320/20ms.

G.723.1 Bit Rate

Choices are 5.3kb/s or 6.3kb/s.

Speakerphone

Volume

Set the speaker calls the volume level. MIC Input Volume

Set the MIC calls the volume level.

Broadcast Output

Volume

Set the broadcast the output volume level. Signal Tone Volume

Set the audio signal the output volume level.

Enable VAD

Enable or disable Voice Activity Detection (VAD). If VAD is enabled, G729 Payload

length cannot be set greater than 20 mSec.

[键入文字]

34/54

Video

Field Name

Explanation

Video Capture

IRCUT Mode

Auto: IRCUT switches according to the actual ambient light level of the camera

Synchronization: The switching of the IRCUT is determined by the actual brightness of

the IR lamp.

Day/Night Mode

Automatic: automatically switches according to the DNC Threshold and the brightness

of the actual environment where the camera is located

Day Mode: The camera's video screen is always colored, if there is IR-cut will be

synchronized to switch.

Night Mode: the camera's video screen is always black and white, if there is IR-cut will

be synchronized switch.

White Balance

Automatic: Automatically adjusts according to the actual environment in which the

camera is located.

Outdoor: installed in the outdoor preferred.

Indoor: installed in the room preferred.

Horizon Flip

The video is flipped horizontally

Anti Flicker

Enable the option. In a fluorescent environment can eliminate the video horizontal

scroll

Vertical Flip

The video is flipped horizontally

IR Swap

IR-cut filter switch

c) Video

This page allows you to set the video capture and video encode.

[键入文字]

35/54

DNC Threshold

In the Day / Night mode Auto option, the color switching black and white threshold is

set

Backlight

Compensation

In front of a very strong background light can see people or objects clearly

AutoFill

Sensitivity

In the environment changes in light and shade, the higher the sensitivity the faster the

video changes

Fill Light

Enable or disable Fill Light

Video Encode

Encode Format

Only H.264 encoding format is supported

Resolution

Main stream: support 720P

Sub-stream: you can select CIF (352 * 288), D1 (720 * 576)

Frame Rate

The larger the value is, the more coherent the video would be got; not recommend

adjusted.

Bitrate Control

CBR: If the code rate (bandwidth) is insufficient, it is preferred.

VBR: Image quality is preferred, not recommended.

Quality

Video quality adjustment, the better the quality needs to transfer faster

Bit rate

It is proportional to video file size, not recommend adjusted.

I Frame Interval

The greater the value is, the worse the video quality would be, otherwise the better

video quality would be; not recommend adjusted.

Activate

When you selected it, the stream is enabled, otherwise disabled

RTSP Information

Main Stream Url

Access the main address of RTSP

Sub Stream Url

Access the child address of RTSP

d) MCAST

[键入文字]

36/54

It is easy and convenient to use multicast function to send notice to each member of the multicast

via setting the multicast key on the device and sending multicast RTP stream to pre-configured multicast

address. By configuring monitoring multicast address on the device, monitor and play the RTP stream

which sent by the multicast address.

MCAST Settings

Equipment can be set up to monitor up to 10 different multicast addresses, used to receive the

multicast RTP stream sent by the multicast address.

Here are the ways to change equipment receiving multicast RTP stream processing mode in the Web

interface: set the ordinary priority and enable page priority.  Priority:

In the drop-down box to choose priority of ordinary calls the priority, if the priority of the incoming

flows of multicast RTP, lower precedence than the current common calls, device will automatically ignore

the group RTP stream. If the priority of the incoming flow of multicast RTP is higher than the current

common calls priority, device will automatically receive the group RTP stream, and keep the current

common calls in state. You can also choose to disable in the receiving threshold drop-down box, the

device will automatically ignore all local network multicast RTP stream.

 The options are as follows:

 1-10: To definite the priority of the common calls, 1 is the top level while 10 is the lowest  Disable: ignore all incoming multicast RTP stream  Enable the page priority:

Page priority determines the device how to deal with the new receiving multicast RTP stream

when it is in multicast session currently. When Page priority switch is enabled, the device will

automatically ignore the low priority multicast RTP stream but receive top-level priority multicast RTP

stream, and keep the current multicast session in state; If it is not enabled, the device will

[键入文字]

37/54

automatically ignore all receiving multicast RTP stream.

 Web Settings:

The multicast SS priority is higher than that of EE, which is the highest priority.

Note: when pressing the multicast key for multicast session, both multicast sender and receiver will

beep.

Listener configuration

 Blue part (name)

"Group 1","Group 2" and "Group 3" are your setting monitoring multicast name.The group name will

be displayed on the screen when you answer the multicast. If you have not set, the screen will display the

IP: port directly.

 Purple part (host: port)

It is a set of addresses and ports to listen, separated by a colon.

 Pink part (index / priority)

Multicast is a sign of listening, but also the monitoring multicast priority. The smaller number refers to

higher priority.

 Red part (priority)

It is the general call, non multicast call priority. The smaller number refers to high priority. The

followings will explain how to use this option:  The purpose of setting monitoring multicast "Group 1" or "Group 2" or "Group 3" launched a multicast

[键入文字]

38/54

call.

 All equipment has one or more common non multicast communication.  When you set the Priority for the disable, multicast any level will not answer, multicast call is rejected.  when you set the Priority to a value, only higher than the priority of multicast can come in, if you set

the Priority is 3, group 2 and group 3 for priority level equal to 3 and less than 3 were rejected, 1

priority is 2 higher than ordinary call priority device can answer the multicast message at the same

time, keep the hold the other call.

 Green part (Enable Page priority)

Set whether to open more priority is the priority of multicast, multicast is pink part number. Explain

how to use:  The purpose of setting monitoring multicast "group 1" or "3" set up listening "group of 1" or "3"

multicast address multicast call.

 All equipment has been a path or multi-path multicast phone, such as listening to "multicast

information group 2".

 If multicast is a new "group of 1", because "the priority group 1" is 2, higher than the current call

"priority group 2" 3, so multicast call will can come in.

 If multicast is a new "group of 3", because "the priority group 3" is 4, lower than the current call

"priority group 2" 3, "1" will listen to the equipment and maintain the "group of 2".

Multicast service

 Send: when configured ok, our key press shell on the corresponding equipment, equipment directly

into the Talking interface, the premise is to ensure no current multicast call and 3-way of the case, the

multicast can be established.

 Lmonitor: IP port and priority configuration monitoring device, when the call is initiated and incoming

multicast, directly into the Talking interface equipment.

e) Action URL

[键入文字]

39/54

Action URL Event Settings

URL for various actions performed by the phone. These actions are recorded and sent as xml files to the

server. Sample format is http://InternalServer /FileName.xml

f) Time/Date

[键入文字]

40/54

Time/Date

Field Name

Explanation

Network Time Server Settings

Time Synchronized via

SNTP

Enable time-sync through SNTP protocol

Time Synchronized via

DHCP

Enable time-sync through DHCP protocol

Primary Time Server

Set primary time server address

Secondary Time

Server

Set secondary time server address, when primary server is not reachable, the device will try

to connect to secondary time server to get time synchronization.

Time zone

Select the time zone

Resync Period

Time of re-synchronization with time server

Date Format

Select the time/date display format

Daylight Saving Time Settings

Location

Select the user's time zone specific area

DST Set Type

Select automatic DST according to the preset rules of DST, or the manually input rules

Offset

The DST offset time

Month Start

The DST start month

Week Start

The DST start week

Weekday Start

The DST start weekday

Hour Start

The DST start hour

Month End

The DST end month

Week End

The DST end week

Weekday End

The DST end weekday

[键入文字]

41/54

Hour End

The DST end hour

Manual Time Settings

The time set by hand, need to disable SNTP service first.

Daylight Saving Time Settings

EGS Access

Field Name

Explanation

Import Access Table

(5) EGS Access

[键入文字]

42/54

Click the <Browse> to choose to import remote access list file (access List.csv) and then clicking

<Update> can batch import remote access rule.

Access Table

According to entrance guard access rules have been added, you can choose single or multiple rules on

this list to delete operation.

Add Access Rule

Name(necessary)

User name

Location

Virtual extension number, used to make position call instead of real number.

It might be taken with unit number, or room number.

RFID card number. You can manually fill in the first 10 digits of the card number or

select the existing card number

Number

User phone number

Card State

Enable or disable holder's RFID card

Fwd Number

Call forwarding number when above phone number is unavailable.

Department

Card holder's department

Access Code

1/ When the door phone answers the call from the corresponding <Phone Num>

user, then the <Phone Num> user can input the access code via keypad to unlock the

door remotely.

2/ The user’s private password should be input via keypad for local door unlocking.

The private password format is Location * Access Code.

Position

Card holder's position

Double Auth

When the feature is enabled, private password inputting and RFID reading must be

matched simultaneously for door unlocking.

Type

Host: the door phone would answer all call automatically.

Guest: the door phone would ring for incoming call, if the auto answer is disabled.

Profile

It is valid for user access rules (including RFID, access code, etc) within corresponding

time section. If NONE is selected, the feature would be taken effect all day.

Profile Setting

Profile

There are 4 sections for time profile configuration

Profile Name

The name of profile to help administrator to remember the time definition

Status

If it is yes, the time profile would be taken effect. Other time sections not included in

the profiles would not allow users to open door

Start Time

The start time of section

End Time

The end time of section

Administrator Table

Add Admin Card

You should input the top 10 digits of RFID card numbers. for example, 0004111806,

selected the type of admin card , click <add>.

[键入文字]

43/54

Type: Issuer and revocation

When entrance guard is in normal state, swipe card (issuing card) would make entrance guard into the

issuing state, and then you can swipe a new card, which the card would be added into the database;

when you swipe the issuing card again after cards added done, entrance guard would return to normal

state. Delete card operation is the same with issuing card.

The device can support up to 10 admin cards, 5000 copies of ordinary cards.

Note: in the issuing state, swiping deleted card is invalid.

Shows the ID, Issuing Date and Type of admin card

Delete

Clicking <Delete> would delete the admin card list of the selected ID cards.

Delete All

Click <Delete All>, to delete all admin card lists.

Field Name

Explanation

Door Open Log

Result

Show the results of the open the door ( Succeeded or Failed)

Time

The time of opening door.

Access Name

If the door was opened by swipe card or remote unlocking door, the device would

display remote access name.

Access ID

1. If the opening door method is swiping card, it wound display the card number

(6) EGS Logs

According to open event log, can record up to 200,000 open event, after more than cover the old

records. Right click on the links to select save target as the door log can export

CSV format.

[键入文字]

44/54

2. If the opening door way is remote access, it wound display the remote extension’s

number.

3. If the opening door way is local access, there is no display information.

Type

Open type: 1. Local, 2. Remote, 3. Brush card (Temporary Card, Valid Card and Illegal

Card).

Note: there are three kinds of brushing card feedback results.

1. Temporary Card (only added ) the card number, without adding other rules )

2. Valid Card (added access rules)

3. Illegal Card (Did not add information)

Type

Subtype

Usage

Key Event

None

No responding

Dial

Dialing function

Release

Delete password input, cancel dialing input and end call

identification key

(7) Function Key

 Key Event

You might set up the key type with the Key Event.

[键入文字]

45/54

Type

Number

Line

Subtype

Usage

Hot Key

Fill the

called

party’s SIP

account or

IP address

The SIP

account

correspondi

ng lines

Speed Dial

Using Speed Dial mode together with

, can define whether this call is allowed to be hung up by

re-pressing the speed dial key.

Intercom

In Intercom mode, if the caller’s IP phone

supports Intercom feature, the device can

automatically answer the Intercom calls

Type

Number

Subtype

Usage

Multicast

Set the host IP address and

port number; they must be

separated by a colon

G.711A

Narrowband speech coding (4Khz) G.711U

G.722

Wideband speech coding (7Khz)

G.723.1

Narrowband speech coding (4Khz)

G.726-32

G.729AB

 Hot Key

You might enter the phone number in the input box. When you press the shortcut key, equipment

would dial preset telephone number. This button can also be used to set the IP address: you can press the

shortcut key to directly make a IP call.

 Multicast

Multicast function is to deliver voice streams to configured multicast address; all equipment

monitored the multicast address can receive and play it. Using multicast functionality would make deliver

voice one to many which are in the multicast group simply and conveniently.

The DSS Key multicast web configuration for calling party is as follow:

[键入文字]

46/54

Field Name

Explanation

Input settings

Input Detect

Enable or disable Input Detect

 operation mechanism

You can define the DSS Key configuration with multicast address, port and used codec. The device can

configure via WEB to monitor the multicast address and port. When the device make a multicast, all

devices monitoring the address can receive the multicast data.  calling configuration

If the device is in calls, or it is three-way conference, or initiated multicast communication, the device

would not be able to launch a new multicast call.

(8) Alert

[键入文字]

47/54

Trigger Mode When choosing the low level trigger (closed trigger), detect the input port 1 (low

level) closed trigger.

When choosing the high level trigger (disconnected trigger), detect the input port 1

(high level) disconnected trigger.

Alert message

send to server

Set the Alert message send to server

Output Settings

Output

Response

Enable or disable Output Response

Output Level When choosing the low level trigger (NO: normally open), when meet the trigger

condition, trigger the NO port disconnected.

When choosing the high level trigger (NO: normally close), when meet the trigger

condition, trigger the NO port close.

Output

Duration

Changes in port, the duration of. The default is 5 seconds.

Alert Trigger Setting

Alarm Ring

Duration

Set the Alarm Ring Duration. The default is 5 seconds.

Trigger Mode: “Input trigger”, “Remote DTMF trigger”, “Remote SMS trigger”, “Call state trigger”.

Call status triggering: there are four triggering modes of Talking / Talking and Ringing / Ringing / Calling

Input trigger

When the input port meet to trigger condition, the output port will trigger(The Port

level time change, By < Output Duration > control)

Remote DTMF

trigger

By duration

Received the terminal equipment to send the DTMF password, if

correct, which triggers the corresponding output port (The Port level

time change, By < Output Duration > control)

By Calling

State

During the call, receive the terminal equipment to send the DTMF

password, if correct, which triggers the corresponding output port (The

Port level time change, (By call state control, after the end of the call,

port to return the default state)

Remote SMS

trigger

In the remote device or server to send instructions to ALERT=[instructions], if correct,

which triggers the corresponding output port

Call state

trigger

When the emergency call button to trigger the equipment shell, which triggers the

corresponding output port(after the end of the call, port to return the default state)

Trigger Message

Format

Send instructions on remote devices or servers, ALERT=[set instructions], if correct,

trigger the corresponding port output.

Tamper Alarm Settings

Tamper Alarm

When the selection is enabled, the tamper detection enabled

[键入文字]

48/54

Alarm

command

When detected someone tampering the equipment, will be sent alarm to the

corresponding server

Reset command

When the equipment receives the command of reset from server, the equipment will

stop alarm

Reset Alerting

Status

Directly stop the alarm from equipment in the Webpage Ring Type

Set the Ring Type

[键入文字]

49/54

Communication protocol

SIP 2.0(RFC-3261)

Main chipset

Broadcom

Keys DSS Key

1 (Stainless steel)

Numeric keyboard

Support

Audio

MIC

Speaker

3W/4Ω

Volume control

Adjustable

Full duplex

speakerphone

Support (AEC)

Speech

flow

Protocols

RTP

Decoding

G.729、G.723、G.711、G.722、G.726

Ports

Active Switched

Output

12V/650mA DC

WAN

10/100BASE-TX s Auto-MDIX, RJ-45

Camera

1/3 "color CMOS, 1 megapixel, wide angle

RFID/IC card reader

EM4100 (125Khz)

MIFARE One(13.56Mhz)

Power supply mode

12V / 1A DC or PoE

PoE

PoE 802.3af (Class 3 - 6.49~12.95W)

Cables

CAT5 or better

Shell Material

Cast aluminium panel, Cast aluminium back shell

Working temperature

-40°C to 70°C

Working humidity

10% - 95%

Storage temperature

-40°C to 70°C

Installation way

Wall-mounting or Flush-mounting

Dimension

Wall-mounting: 223*130*74mm

Flush-mounting: 270*150*61mm

Package size

310x175x115mm

Equipment weight

1500g

Gross weight

1800g

V Appendix

1. Technical parameters

[键入文字]

50/54

Lock status

Call status

Ring status

Network and registration status

Housing

Speaker

Numeric keypad

(password and dialing)

DSS key with LED

MICs

RFID area

Camera

Infrared light

2. Basic functions

 2 SIP lines  PoE Enabled  Full-duplex speakerphone (HF)  Numeric keypad (Dial pad or Password input)  Intelligent DSS Keys (Speed Dial/intercom etc)  Wall-mounting / Flush-mounting  Integrated RFID Card reader  1 indoor switch interface  1 electric lock relay  Anti-tamper switch  External power supply  Door phone: call, password, RFID card, indoor switch  Protection level: IP65, IK10, CE/FCC

3. Schematic diagram

[键入文字]

51/54

VI Other instructions

1. Open door modes

 Local

1) Local Password

 Set <Local Password> (the default is "6789") via DOOR PHONE\DOOR PHONE as above.  Use the device's keypad to input password and "#" key, then the door will be unlocked.

2) Private access code

 Set <Add Access Rule\Access Code> and enable local authentication.  Use the device's keypad to input access code and "#" key, then the door will be unlocked.

 Remote

1) Visitors call to owner

 Visitors call to owner via position speed dial or phone number. (When set the speed dial key, can

press it to call direct.)

 The owner answers the call, with pressing the "*" key to unlock the door for visitors.

2) Owner calls to visitors

 Owner calls to visitors via SIP phone.  SIP door phone answers the call automatically.  Owner use keypad to input corresponding <Access codes> to unlock the door.

 Slot cards

 Use pre assigned RFID cards to unlock the door, by touching RFID area of device.

 Indoor switch

 Press indoor switch, which is installed and connected with device, to unlock the door.

2. Management of card

 Add Administrator

There are 2 types of Administrator cards: issuer used for adding cards, revocation used for deleting

cards.

[键入文字]

52/54

1) Add<Issuer admin card >

Input a card’s ID, selected <Issuer> in the types and Clicked <Add>, you can add Issuer admin card.

2) Add<Revocation admin card>

Input a card’s ID, selected <Revocation> in the types and Clicked <Add>, you can add Revocation

admin card.

3) Administrator Table

 Delete Administrator

Select the admin card of need to delete, click <Delete>.

 Add user cards

Method 1: used to add cards for starters typically

1) In web page < EGS Setting\Card Reader Working Mode> option, select <Card Issuing> function.

2) Click <Apply>, Card Reader would be entered the issuing status.

3) Use new card to touch card reader induction area, and then you might hear the confirmed indication

tone from the device. Repeat step 3 to add more cards.

4) In web page <EGS Setting\Card Reader Working Mode > option, select <normal> function.

[键入文字]

53/54

Only need input the before 10 Numbers.

5) Click <Apply>, Card Reader would be back to the Normal status.

6) The issuing records can be found from the Access table list.

Method 2: used to add cards for professionals

1) Use <Issuer admin card> to touch card reader induction area, and it would be entered issuing card

status.

2) Use new card to touch card reader induction area, and you might hear the confirmed indication tone

from the device. Repeat step 2 to add more cards.

3) Use <Issuer admin card> to touch card reader induction area again, it would be back to normal

working status.

Methods 3: use to add few cards

1) Input cards number in <EGS Setting\Add Access Rule\ID> page, and then click <Add>.

Note: you can also use the USB card reader connected with PC to get cards ID automatically.

[键入文字]

54/54

 Delete user cards

Method 1: used to batch delete cards for starters.

1) In web page <EGS Setting\Card Reader Working Mode> option, select <Card revoking>.

2) Click <Apply>, Card Reader would be entered the revoking status.

3) Use card to touch card reader induction area, and you might hear the card reader confirmed

indication tone. Repeat step 3 to delete more cards.

4) In web page <EGS Setting\Card Reader Working Mode >option, select <normal>.

5) Click <Apply>, Card Reader would be back to the Normal status.

Method 2: used to batch add cards for intermediates.

1) Use < Revocation admin card> to touch card reader induction area, and it would be entered revoking

card status.

2) Use the cards you want to delete from system, to touch card reader induction area, and you might

hear the card reader confirmed indication tone. Repeat step 2 to delete cards.

3) Use <Revocation admin card> to touch card reader induction area, and it would be back to card read

only status.

Method 3: use to batch delete cards or delete few cards.

1) In web page<EGS Access\Access Table>select the card ID and then click <Delete>.

Note: If you click <Delete All>, system will delete all the ID cards.

FANVIL FANVIL I31S User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

I Product introduction

1. Appearance of the product

2. Description

II Start Using

1. Confirm the connection

3) Wiring instructions

2. Quick Setting

III Basic operation

1. Answer a call

2. Call

3. End call

4. Open the door operation

IV Page settings

1. Browser configuration

2. Password Configuration

3. Configuration via WEB

(1) System

a) Information

b) Account

c) Configurations

d) Upgrade

e) Auto Provision

f) Tools

(2) Network

a) Basic

b) VPN

(3) Line

a) SIP

b) Basic Settings

(4) EGS Setting

a) Features

b) Audio

c) Video

d) MCAST

e) Action URL

f) Time/Date

(5) EGS Access

(6) EGS Logs

(7) Function Key

(8) Alert

V Appendix

1. Technical parameters

2. Basic functions

3. Schematic diagram

VI Other instructions

1. Open door modes

2. Management of card