MAGIC WF 4000
WATER FILTER
VACUUM CLEANER
TYPE WF W 11
USER’S GUIDE
COMPONENT PARTS
1- Carrying Handle
2- ON-OFF Switch
3- Motor Bonnet
4- Buoy (float valve)
5- Sponge Filter
6- Inner Bonnet
7- Water Filter Exhaust
8- Locking Latch
9- Tank
10- Suction Mouth
11- Wheeled Base
12- 360° turnable wheels
ACCESSORIES
1- Hose Handle
2- Air Discharging Hole
3- Hose
4- Hose Connecter
For Suction Mouth
5- Extension Tubes
6- Floor Nozzle
7- Upholstery Nozzle
8- Crevice Nozzle
9- Paper dustbag
PRECAUTIONS (READ BEFORE USING)
PRECAUTIONS
• Make sure that the voltage on the power name plate of the
device corresponds to the voltage of your network.
• Use your machine with the right currency. The plug has to be
protected with min.10 amperes.
• In order not to compromise the safety of the appliance, use only
original spare parts and accessories. The warranty is not valid
if unsuitable spare parts and accessories are used in any way.
• Do not damage the isolation of the cable. In case of damage,
the cable has to be immediately replaced by an authorised
service center. Do not operate the appliance with the damaged
cable.
• Use your machine by the user’s guide shown. Do not use it for
any other purpose.
• Unplug your machine before doing any maintenance or before
cleaning. Do not leave your machine plugged in.
• Do not touch the cable with wet hands.
• Do not pull the machine by its cable or close door on the cable.
Do not move your machine as it will coil the cable.
• Do not let your children play with the machine. Pay attention
while operating your machine near children.
• Put a paper dustbag in the vacuum cleaner before using dry
vacuuming function.
• Keep the machine away from direct heat such as; stove, oven,
etc.
• Do not work near inflammable or explosive fluids or gas. Keep
your machine away from burning materials.
• Never vacuum warm fluids or materials at more than 60 C, such
as burning cigarettes, ashes, glowing coals, etc.
• Do not use your machine for cleaning materials such as razorblade,nail and especially do not suck up explosive liquids, acids,
oil or solvents which may cause explosions.
• Do not vacuum unhealty dust.
• Before wet vacuuming function, do not forget to take out the
paper dustbag.
• Water filter exhaust should always be kept clean. This will let
your machine’s suction power at max. level.
ASSEMBLY FOR WATER FILTRATION FUNCTION
• Unlock the locking latches pulling outwards
as shown in the figure.
• Put the motor bonnet away through holding
it from carrying handle.
•Put water filter exhaust inside the tank as
shown in the figure by pushing through the
suction mouth.
• Fill the tank with water by respecting the
exact amount of water indicated on the tank
as “MAX. WATER LEVEL” . (3,5 lt.)
NOTE: The level of the water should be
same as the level indicated on the product
with MAX. WATER LEVEL .
• Put the inner bonnet into the tank as shown
in the figure.
• Put the motor bonnet back on the tank
through holding it from carrying handle and
lock the latches by pushing right and left.
NOTE: Do not operate your machine
without water when using water filtration
function.
WARNING: Detergent residual, from
handy cleaning of the carpets and
parquetries causes foaming in the tank.
In that case immediately switch off the
machine and change the water in the
tank, otherwise your motor will be
damaged by foams.
DRY VACUUMING FUNCTION WITH PAPER DUSTBAG
• Unlock the locking latches pulling outwards
as shown in the figure.
• Put the motor bonnet away through holding
it from carrying handle.
• Lock the paper dustbag to the clips which
are on the back side of the suction mouth.
• The paper dustbag should be fixed into the
tank as shown in the figure.
• Put the motor bonnet back on the tank through
holding it from carrying handle and lock the
latches by pushing right and left.
• Put the hose into the suction mouth and
choose the right choice of accessory for dry
vacuuming function.
NOTE: Only the paper dustbag should be
fixed into the tank while using dry
vacuuming function.
NOTE: Always keep a reserve of paper
dustbag, so that the vacuum cleaner will
be ready for use at any time.
ASSEMBLY FOR WET VACUUMING FUNCTION
• Unlock the locking latches pulling outwards
as shown in the figure.
• Put the motor bonnet away through holding
it from carrying handle.
• The tank should be clean while using wet
vacuuming function. The paper dustbag,
inner bonnet and water filter exhaust should
certainly be removed out of the tank.
• Put the motor bonnet back on the tank
through holding it from carrying handle and
lock the latches by pushing right and left.
• Put the hose into the suction mouth and
choose the right choice of accessory for wet
vacuuming function.
• When the vacuumed water has reached to
max. level, the buoy will automatically stop
vacuuming. In that case, empty the tank then
you may go on vacuuming
NOTE: Do not put water into your tank
during wet vacuuming function.
ASSEMBLY FOR ACCESSORIES
• After connecting the tubes to each other and to
the hose handle, attach the right choice of
accessory to the extension tubes.
• Instead of using two extension tubes, you can
use your machine with only one tube or without
any extension tubes by connecting the right
choice of accessory for your wet vacuuming
area directly to the hose handle.
MAINTENANCE AND CLEANING
• Unplug your machine before doing any maintenance or before
cleaning. Do not leave your machine plugged in.
• Empty the tank after each fuction.
NOTE: To prevent bad odors, don’t leave any liquid in the tank.
Clean and keep empty the tank after each operation.
• After wet vacuuming function, dry tubes, hose and parts of the motor
properly. After filling out and drying the tank, operate the machine
for a few minutes in order to prevent bad odors.
• Do not wash the motor bonnet and do not put it in water. Only clean
it by mopping.
• Clean the tank by mopping or washing.
• Clean the accessories by mopping or washing.
• Change paper dustbag with a new one when it gets full.
• From time to time water filter exhaust should be
cleaned to ensure higher performance. You can wash
sponge filters when they get dirty.
TECHNICAL SPECIFICATIONS
TYPE WF W 11
Nominal Voltage : 220-230 V AC
Nominal Frequency : 50/60 Hz
Power : 1400 W
: IPX4
Loading...