Fantasea BlueRay Sport, 6031 Instruction Manual
1
Fantasea BlueRay Sport Video Light Instruction Manual 20121206
Fantasea BlueRay Sport Video Light
(Cat. No. 6031)
Instruction Manual
The BlueRay Sport Video Light is an ultra-compact,
durable and powerful video light, which was
designed to enhance color and lighting in
underwater videos. It can be used with any
underwater video system. It is lightweight and
features a compact design, which allows it to be
comfortably integrated in small-sized photo
systems, such as with action cams, waterproof and
amphibious cameras, compact digital housings and
more. With a burn time of 160 minutes in full
power per set of batteries, the light can be used for
a whole diving day without having to charge it in
between the dives. Adjustable power output allows
controlling the intensity of the beam in various
compositions and diving conditions, as well as extending the burn time of the light. Color
temperature of the beam is slightly warmer than daylight, which assists with producing vivid and
colorful videos without having to use any color correction filters. The light features a wide beam
angle of 75 degrees, making it suitable to light a wide range of compositions.
Depth rated to 100 meters/330 feet, the BlueRay Sport Video Light fulfills the needs of both
recreational and technical divers.
Specifications
Depth ratio: 100 meters / 330 feet
Maximum output: 700 lumens
Beam angle: 75 degrees
Material: Aluminum head, Polycarbonate body
Battery requirements: 1 x 18650 Li-ion battery or 2 x CR123 batteries
Burn time: 160 minutes at 100% power / 400 minutes at 40% power
LED Lifespan: 30,000 hours
Color temperature – approx. 6,000K
Operation modes: 100% power, 40% power
Dimensions: 37.5 x 129 mm (diameter x length)
Weight: 114g (without battery)
Includes: Hand lanyard and instruction manual
Optional YS Mount available – BlueRay YS Mount A (Cat. No. 4028)
Optional Red Filter available - RedEye Filter ORF37.5 (Cat. No. 5185)
2
Fantasea BlueRay Sport Video Light Instruction Manual 20121206
Instructions for Use
A. Installing & Removing Batteries
a. Please read the following information and warnings prior to purchasing and installing
batteries inside the BlueRay Sport Video Light:
i. Only 2 x CR123/CR123A 3-Volt Lithium batteries or a single 18650
rechargeable 3.7-volt Li-Ion battery should be installed inside the light.
ii. Installation of rechargeable CR123 Li-on batteries inside the light is strictly
forbidden, as this will burn out the light and may cause irreparable damage.
iii. If installing an 18650 battery inside the light, make sure that it features a
protective circuit board (PCB). 18650 batteries with a protective circuit board
are also known as 19670.
iv. Warning! Lithium-ion batteries can explode or cause a fire if they are used
incorrectly or if they are defective. Therefore, you are recommended to read
the following instructions very carefully:
1) Each time before using the battery, carefully check the battery and in
particular the protective seal/casing to make sure that it is undamaged and
intact. If in doubt, take the battery to a chemical waste disposal facility.
2) Always handle the battery with care. Never drop the battery!
3) Store the battery in a safe and dry place and keep the battery away from
all metal objects.
4) Never expose the battery to temperatures above 100 degrees Celsius.
5) Only use chargers that have specially been designed for use with lithium-
ion batteries.
6) When charging batteries, keep the charger away from highly flammable
materials or products and never leave the charger unattended when in
use.
7) Please follow the guidelines and restrictions of the batteries you purchase
in order to avoid any damage.
b. To open the BlueRay Sport Video Light, hold the hand grip firmly in one hand with the
hand grip pointing towards your body and the LED head pointing away. Turn the LED head
clockwise until it separates. Pull the LED head off.
c. Install or remove 1 x 18650 Li-ion battery or 2 x CR123 batteries inside the body of the
light. Make sure to follow the instructions diagrams printed on the interior of the battery
compartment and note that batteries should be installed with their positive ends pointed
towards the LED head.
d. Once batteries were installed inside the light, re-install the LED head on the opening,
carefully aligning it with the thread on the body of the light and tightening it evenly in a
counterclockwise fashion. Do not use force and do not allow it to screw down unevenly.
Tighten the LED head until the light goes on and then unscrew it clockwise a bit, just
Loading...