Fanimation The Stafford PL8274 Owner's Manual
™
The Stafford
Ceiling Fan
Model No. PL8274**
OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Net Weight 10.54 kg (23.21 lbs)
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly
diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling
fan before servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
6. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be
supervised to ensure that they do not play with the appliance.
Additional Safety Instructions
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without
blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The
ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or
approved by a licensed electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. (fan and accessories not to
exceed 35 lbs. or 15.88 kgs.). See page 5 of owner’s manual for support requirements. Consult a qualified electrician if in
doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate
electrical knowledge or experience, have your fan installed by licensed electrician.
6. Suitable for use with solid-state speed controls.
7. This fan is to be used in dry location only.
8. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a
grounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be
connected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it
should be connected to an equipment-grounding conductor.
:
WARNI NG
ISOLATING WALL CONTROL/SWITCH.
WARNING:This product is designed to use only those parts supplied with this product and/or accessories designated
specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in
personal injury or property damage.
WARNING:To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the
brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING:Mount to an outlet box marked acceptable for fan support.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. If the intentional radiator can be classified as a Class B digital device or a PC
peripheral, then shall include the following or equivalent:
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.
TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE,
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship
during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective
fan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costs
incurred in the removal or reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due
to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service
center. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for all
costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or
workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our
national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting,
corroding, tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to
extremes of heat or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that
sold the fan or Fanimation.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this
warranty.
8. Under no circumstances may a fan be returned without prior authorization from
accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly
packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other
expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to
those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow
limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out
of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you
special legal rights and you may also have other rights that vary from state to state.
10.A certain amount of wobble is normal and should not be considered a problem or a defect.
Table of Contents
Fanimation. The receipt of purchase must
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . .
Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . .
Electrical and Structural Requirements . . . . . . . . . . . .
How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . .
How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . .
How to Wire Your Ceiling Fan. . . . . . . . . . . . . . . . . . . .
How to Install Your Canopy Housing . . . . . . . . . . . . . .
10
11
4
5
5
7
9
How to Assemble the Blades and Light Kit. . . . . . . . . .
How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . .
How to Install Your Remote Control . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . .
11
14
15
15
15
16
17
18
This manual is designed to make it as easy as possible for you
to assemble, install, operate, and maintain your ceiling fan
Tools Needed for Assembly Materials
• One Phillips head screwdriver
• One stepladder
• One ¼˝ blade screwdriver
• One wire stripper
• Three wire connectors
(supplied)
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3conductor (2-wire with ground) of the following size:
Wire Size A.W.G.Installed Wire Length
▲
WARNING
Before assembling your ceiling fan, refer to
proper method of wiring your fan (page 10). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
section
on
Up to 50 ft.
50 - 100 ft.
NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are missing,
contact your local retailer.
14
12
Unpacking Instructions
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in fi nding your place should you be interrupted.
▲
WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer to
exploded view illustration. (Figure 1, page 18)
Fan Motor Assembly•
Hanger Bracket Assembly•
Downrod/Hanger Ball Assembly •
Ceiling Canopy•
Canopy Screw Cover Assembly•
Motor Coupling Cover Assembly•
Light Plate Assembly•
Socket Plate Assembly•
Blade Holder Set•
Blade Set•
Glass Assembly •
Light Bulbs •
Hand Held Remote •
Receiver Unit•
• Hardware bag:
– Eleven ¼˝-20 x 14 mm
(blade holder to fan motor hub)
screws with lockwashers
– Sixteen ˝-24 x 7.5 mm (blade
to blade holder) washer-head
screws
– Fiber Washers
– Phillips Screwdriver 4˝
– Wire Nuts
– Balance Kit
3
/16
Canopy Screw Cover
Assembly
Hanger Bracket
Assembly
Motor Coupling Cover
Assembly
Ceiling Canopy
Fan Motor Assembly
Downrod/
Hanger Ball Assembly
Light Plate Assembly
Socket Plate Assembly
Glass Assembly
4
Blade Holder Set
Hand-Held Remote
Light Bulbs
Receiver
Unit
Blade Set
Hardware Bag
Energy Efficient Use of Ceiling Fans
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the ceiling
fan. Here are a few tips to ensure efficient product
performance.
Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the middle
of the room and at least 7 feet above the floor and 18
inches from the walls. If ceiling height allows, install the fan
8 - 9 feet above the floor for optimal airflow. Consult your
Fanimation Retailer for optional mounting accessories.
Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.
Electrical and Structural Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 HZ, 15 Amp Circuit.
Electrical code requires use of a fan-rated outlet box to
support the extra weight and motion associated with a
ceiling fan. A fan-rated box will be labeled as such and
typically supports up to a 70lb ceiling fan. Fan-Rated
Outlet Boxes vary in ratings and design. Ensure the
ratings of your ceiling fan outlet box meet the
requirements for the ceiling fan being installed. Figure 1,
Figure 2 and Figure 3 depicts different structural
configurations that may be used for mounting the
outlet box.
Low profile box (Figure 1)
A 1⁄2-in.-deep pancake box is meant to be screwed to a
joist or block. It’s used if only one cable is coming into
the box. It is also available in a saddle-mount
configuration.
Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the counter-
clockwise direction. The airflow produced by the ceiling
fan creates a wind-chill effect, making you “feel” cooler.
Select a fan speed that provides a comfortable breeze,
lower speeds consume less energy.
Winter Season: Reverse themotor andoperate the ceiling
fan at low speed in the clockwise direction. This produces
a gentle updraft, which forces warm air near the ceiling
down into the occupied space.Remember to adjust your
thermostat when using your ceiling fan - additional energy
and dollar savings could be realized with this simple step!
CEILING JOIST
2" x 4"
CEILING
OUTLET BOX
Figure 1
Deep box (Figure 2)
A 2-1⁄4-in.-deep box can be attached to blocking
between joists and is roomy enough to handle more
than one cable.
CEILING JOIST
2" x 4"
CEILING
Figure 2
OUTLET BOX
5
Electrical and Structural Requirements (Continued)
Deep box with brace (Figure 3)
Paired with a deep box, this hanger is meant to span
between two joists and takes the place of wooden
blocking.
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount to outlet box marked acceptable for fan
support of 15.9 kg (35 lbs) or less and use mounting
screws provided with the outlet box. Most outlet boxes
commonly used for the support of luminaires are not
acceptable for fan support and may need to be
replaced, consult a qualified electrician if in doubt.
If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and
remove the existing light fixture.
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
CEILING JOIST
CEILING
OUTLET BOX
Figure 3
WARNING
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
inst ructions should b e done or a pproved by a
licensed electrician.
6
How to Assemble Your Ceiling Fan
1. Remove the hanger ball portion from the downrod
/hanger ball assembly by loosening the set screw
in the hanger ball until the ball falls freely down the
downrod. Remove the pin from the downrod, then
remove the hanger ball. Retain the pin and
hanger ball for reinstallation in Step 6 (Figure 1).
2. Remove the hairpin clip and clevis pin from the
bottom of downrod. Retain the pin and clip for
reinstallation in Step 4 (Figure 2).
3. Loosen the two set screws in the downrod support.
Route black, blue and white lead wires through the
downrod (Figure 3).
Pin
Downrod
Set Screw
Hanger Ball
Figure 1
Hairpin
Clip
Clevis Pin
Figure 2
Black, Blue and
White Leads
4. Position downrod support and align the clevis pin
holes in both parts. Install the clevis pin and secure
with the hairpin clip.Tighten the two set screws
and locking nuts in the downrod support (Figure 4).
WARNING
It is critical that the clevis pin in the downrod support
is properly installed and the set screws and nuts are
securely tightened. Failure to do so could result in
the fan falling.
5. Route wires through motor coupling cover, canopy
screw cover and canopy (Figure 5).
Downrod Support
Hairpin Clip
Figure 3
Figure 4
Downrod
Downrod
Clevis Pin
Canopy Screw
Cover
Set Screws and
Locking Nuts (2)
Canopy
Motor Coupling
Cover
Figure 5
7
How to Assemble Your Ceiling Fan (continued)
6. Reinstall the hanger ball on the downrod as
follows. Route the three 80-inch wires through the
hanger ball. Position the pin through the two holes
in the downrod and align the hanger ball so the pin
is captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin.
Securely tighten the set screw in the hanger ball.
A loose set screw could create fan wobble (Figure 6).
7. Cut off excess lead wire approximately 6 to 9
inches above top of the top of the downrod. Strip
insulation off 1/2-inch from the end of each lead
wire (Figure 7).
Figure 6
NOTE:
where necessary, before installation.
All set screws must be checked, and retightened
Figure 7
8
How to Hang Your Ceiling Fan
WARNING
To avoid possible fire or shock, be sure electricity is
turned off at the main fuse box before hanging.
(Figure 1)
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advise, as it must be
grounded for safe operation.
MAIN FUSE BOX
Figure 1
WARNING
The fan must be hung with at least 7’ of clearance
from floor to blades. (Figure 2)
1. Securely attach the hanger bracket to the outlet
box using the outlet box screws and washers
supplied with the outlet box (Figure 3).
WARNING
The outlet box must be securely anchored. Hanger
bracket must seat firmly against outlet box. If the outlet
box is recessed, remove wall board until bracket
contacts box. If bracket and /or outlet box are not
securely attached, the fan could wobble or fall.
2. Carefully lift the fan and seat the downrod/hanger
ball assembly on the hanger bracket that was just
attached to the outlet box. Be sure the groove in
the ball is lined up with tab on the hanger bracket
(Figure 4).
CEILING
FLOOR
Figure 2
Figure 3
NO LESS
THAN
7 FEET
TAB
OUTLET BOX
Washers
SCREW (2)
(Supplied with
Outlet Box)
OUTLET BOX
!
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
!
WARNING
To avoid possible shock, do not pinch wires between
the hanger ball assembly and the hanger bracket.
Figure 4
9
How to Wire Your Ceiling Fan
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before hanging
(Figure 1).
MAIN FUSE BOX
NOTE:
If you are not s ure if the out let box i s
grounded, contact a licensed electrician for advice, as
it must be grounded for safe operation.
NOTE:
The hand-held remote included with this fan
has 16 different code combinatio ns. To prev ent
possible interference from or to other remote units,
sim ply change the com bination code i n yo ur
transmitter and receiver.
1. To set the transmitter code, remove battery cover
by pressing firmly below arrow and sliding cover
off. Slide code switches to your choice of up or
down position. Factory setting is all up. Do not use
this position. With a small screwdriver or ball point
pen slide firmly up or down. Replace battery cover on
the transmitter (Figure 2).
2. To set the receiver unit code, slide code switches
to the same positions as set on your transmitter
(Figure 3).
Remote Transmitter
Unit Detail
ON ECE
Receiver Unit Detail
ON ECE
Figure 1
ON ECE
1 2 3 4
Figure 2
ON ECE
Figure 3
3. Slide the receiver unit into the open end of the
hanger bracket (Figure 4).
4. Connect green wires from hanger bracket and
hanger ba ll t o ba re ( ground) wire using wire
co nnector supplied. Connect black wire fr om
receiver unit marked “AC IN L” to black supply wire
using wire connector supplied. Connect white wire
from receiver unit marked “AC IN N” to white supply
wire using wire connector supplied. Connect white
wire from receiver unit marked “TO MOTOR N” to
white wire from fan using wire connector supplied
with receiver. Connect black wire from receiver unit
marked “TO MOTOR L” to black wire from fan
using wire connector supplied. Lastly, connect blue
wire from receiver to the blue fan light wire using
wire connector supplied. Position all connected
wires and receiver antenna to allow installation of
ceiling canopy (Figure 5).
After splicing and making the wire connections, the
5.
wires should be spread apart and turned upward with
the grounded conductor and the equipment-grounding
conductor on one side of the outlet box and the
ungrounded conductor on the other side of the outlet
box. (Figure 5)
RECEIVER UNIT
HANGER BRACKET
Figure 4
Figure 5
10
How to Install Your Canopy Housing
NOTE: This step is applicable after the neccessary wiring is
completed.
1. Remove one of the two shoulder screws in the
hanger bracket. Loosen the second shoulder screw
without fully removing it. Assemble canopy by
rotating key slot in canopy over shoulder screw in
hanger bracket. Tighten shoulder screw. Fully
assemble and tighten second shoulder screw that
was previously removed. (Figure 1)
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy
housing and not pinched between the housing and the
ceiling.
Ceiling Canopy
Figure 1
2. Securely attach and tighten the canopy screw cover
over the shoulder screws in the hanger bracket utilizing
the keyslot twist-lock feature. (Figrue 2)
How to Assemble the Blades and Light Kit
1. Position the blade over the blade holder with
threaded posts showing. Make sure the bottom
edge of the blade is fully seated against the blade
arm. With a Phillips screwdriver, tighten 3/16˝-24 x
7.5 mm washer head screws and fiber washers to
secure the blade to the blade arm (Figure 1).
CAUTION
Do not connect fan blades until the fan is completely
installed. Installing the fan with blades assembled
may result in damage to the fan blades.
Blade holder
Figure 2
3/16˝-24 x 7.5 mm WASHER
HEAD SCREW AND FIBER
WASHER (3 each per blade)
Blade
Figure 1
HARDWARE USED:
3/16˝-24 x 7.5 mm
WASHER HEAD
SCREWS
Canopy Screw
Cover
x 15
2. Secure the blade holders to the motor assembly
using the 1/4˝-20 x 14 mm screws (Figure 2).
NOTE:
Periodically check blade holder hardware and
resecure if necessary.
!
WARNING
To reduce the risk of personal injury, do not bend the
blade holders when installing, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between the rotating blades.
CAUTION
To reduce the risk of electric shock, disconnect the
electrical supply circult to the fan before installing
light kit.
Blade Holder
1/4˝-20 x 14 mm Screws
(2 per assembly)
11
FIBER WASHER
Figure 2
HARDWARE USED:
1/4˝-20 x 14 mm
SCREWS
x 15
Motor
Assembly
x 10
How to Assemble the Blades and Light Kit
3. Remove one of the three screws in the support
bracket at the bottom of the motor assembly.
Slightly loosen the remaining two screws and
retain the removed screw (Figure 3).
4. Connect the black wire from the socket plate
assembly to the black wire from the motor assembly,
and the white wire from the socket plate assembly
to the white wire from the motor assembly (Figure 4).
Motor
Assembly
Figure 3
Motor Assembly
Single Pin Connector
Socket Plate
Single Pin Connector
5. Assemble the socket plate assembly to the motor
assembly using the two key slots. Replace the
previously removed screw and securely tighten all
three screws (Figure 5).
Remove one of the three screws in the socket
6.
plate assembly. Slightly loosen the remaining
two screws. Assemble the light plate assembly
to the socket plate assembly using the two key
slots in light plate assembly. Replace the third
screw and securely tighten (Figure 6).
Screws (3)
Figure 4
Figure 5
Figure 6
Socket Plate
Assembly
Socket Plate
Assembly
Socket Plate
Assembly
Light Plate
Assembly
12
Loading...