How it Works
Fanimation
Loading...
I
J
K
L
M
O
P
R
S
T
V
W
X
Z
Loading...
Loading...
The Camhaven FP8095 Series
Owner's Manual
38 pgs4.55 Mb0

Fanimation The Camhaven FP8095 Series Owner's Manual

The Camhaven
Ceiling Fan
™
Model Nos. FP8095**
OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Net Weight 11.10 kg (24.45lbs)
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. Consult a qualified electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical knowledge or experience, have your fan installed by licensed electrician.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with Fan Speed Control Part No. UC7067RYL, manufactured by Rhine Electornic Co., Ltd.
WARNING: WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property damage.
WARNING:
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: Mount to an outlet box marked acceptable for fan support.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the intentional radiator can be classified as a Class B digital device or a PC peripheral, then shall include the following or equivalent: Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TO REDUCE THE RISK OF SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.
To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding, tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of heat or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or Fanimation.
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac­company authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary from state to state.
10. A certain amount of wobble is normal and should not be considered a problem or a defect.
Table of Contents
Unpacking Instructions
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . .
How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Hang Your Ceiling Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Wire Your Ceiling Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Canopy Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembling and Mounting the Fan Blades. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5 . . . . .. . . . . . . . . . . . . . . . . . . . . .sn aF gnilieC fo e sU tn eic iffE ygre nE
5 6 8 9
10
Assembling Fan With the Light Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assembling Fan Without the Light Kit . . . . . . . . . . . . . . . . . . . . . . . .14
How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Blade Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Trouble Shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
This Manual is Designed to Make it as Easy as Possible for You
to Assemble, Install, Operate, and Maintain Your Ceiling Fan
Tools Needed for Assembly Materials
• One Phillips head screwdriver
• One stepladder
• One ¼” blade screwdriver
• One wire stripper
• Four wire connectors
(supplied)
Wiring outlet box and box connectors must be of type required by local code. The minimum wire would be a 3­conductor (2-wire with ground) of the following size:
Wire Size A.W.G.Installed Wire Length
▲
WARNING
Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 9). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.
Up to 50 ft. 50 - 100 ft.
NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing, contact your local retailer.
14 12
Unpacking Instructions
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
. de t pur r e t n i eb uoy d l uohs eca l p r uoy gn i dn i f n i l u f p l eh eb l l iw dna de t e l pmoc neeb evah spe t s
▲
WARNING
Do not install or use fan if any part is damaged or missing. This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer to exploded view illustration. (Figure 1, page 16)
Fan Motor Assembly• Adapter/Switch Cup Assembly• Hanger Bracket Assembly• Ball Downrod Assembly • Canopy• Canopy Screw Cover Assembly• Motor Coupling Cover Assembly• Blade Holder Set• Blade Set• Glass Bowl •
Light Bulb • Remote Hand Held• Receiver Unit•
•Hardware bags:
– 3/16-24 x 8mm
(blade to blade holder) Washer Head Screw
– 3/16” Fiber Washer
(blade to blade holder)
– 1/8”-27 x 9.5 mm
Phillips Screw
– 1/4”-20 x 14mm
(blade arm to motor)
Pan Head Screw
– Phillips Screwdriver, 4”
– Wire Connectors – Balance Kit
Hanger Bracket
Ceiling Canopy
Assembly
Fan Motor Assembly
Adapter/Switch Cup Assembly
Glass Bowl
Motor Coupling Cover Assembly
75-Watt
Minican Bulbs
TR24
Hand-Held Remote
4
Canopy Screw Cover Assembly
Blade Holder Set
Receiver Unit
Ball Downrod Assembly
Blade Set
Hardware Bag
Energy Efficient Use of Ceiling Fans
Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance.
Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the middle of the room and at least 7 feet above the floor and 18 inches from the walls. If ceiling height allows, install the fan 8 - 9 feet above the floor for optimal airflow. Consult your Fanimation Retailer for optional mounting accessories.
Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is unoccupied, turn off the ceiling fan to save energy.
Electrical and Structural Requirements
Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different structural configurations that may be used for mounting the outlet box.
Using the Ceiling Fan Year Round Summer Season: Use the ceiling fan in the
counterclockwise direction. The airflow produced by the ceiling fan creates a wind-chill effect, making you “feel” cooler. Select a fan speed that provides a comfortable breeze, lower speeds consume less energy.
Winter Season: Reverse the motor and operate the ceiling fan at low speed in the clockwise direction. This produces a gentle updraft, which forces warm air near the ceiling down into the occupied space. Remember to adjust your thermostat when using your ceiling fan - additional energy and dollar savings could be realized with this simple step!
CEILING
WARNING
To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box marked acceptable for fan support of 22.7 kg (50 lbs) or less. Use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
If your fan is to replace an existing light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.
WARNING
Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. Al l wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.
CEILING JOIST
2" x 4"
OUTLET BOX
Figure 1
WARNING
To avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician.
5
How to Assemble Your Ceiling Fan
1. Remove the hanger ball portion from the downrod /hanger ball assembly by loosening the set screw in the hanger ball until the ball falls freely down the downrod. Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in Step 5 (Figure 1).
2. Remove the hairpin clip and clevis pin from the bottom of downrod. Retain the pin and clip for reinstallation in Step 4 (Figure 2).
Downrod
Hanger
Ball
Hairpin Clip
Pin
Setscrew
Figure 1
Clevis Pin
3. Loosen the two set screws in the downrod support.
Route black, blue and white lead wires through the downrod (Figure 3).
4. Position downrod support and align the clevis pin holes in both parts. Install the clevis pin and secure
with the hairpin clip.Tighten the two set screws and locking nuts in the downrod support (Figure 4).
▲
WARNING
It is critical that the clevis pin in the downrod support is properly installed and the setscrews and nuts are securely tightened. Failure to verify that the clevis pin, hairpin clip, setscrews and nuts are properly installed could result in the fan falling.
SetScrew(2)
Hairpin Clip
Figure 2
Downrod
Figure 3
Clevis Pin
Set Screw
Figure 4
6
How to Assemble Your Ceiling Fan (continued)
5. Route wires through motor coupling cover,
canopy screw cover and ceiling canopy. (Figure 5)
Ceiling
Canopy
6. Reinstall the hanger ball on the downrod as
follows. Route the three 80 in. Wire through the hanger ball. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin. Securely tighten the set screw in the hanger ball. A loose set screw could create fan wobble. (Figure 6)
7. Cut off excess lead wire approximately 6 to 9
inches above top of the top of the downrod. Strip
insulation 1/2 inch from the end of each lead wire. (Figure 7)
Motor
Coupling
Cover
Hanger Ball
Canopy Screw Cover
Figure 5
Figure 6
NOTE:
where necessary, before inst allation.
All set screws must be checked, and retightened
Figure 7
7
How to Hang Your Ceiling Fan
▲
WARNING
To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging.
NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation.
▲
WARNING
The fan must be hung with at least 7´ of clearance from floor to blades (Figure 8)
▲
WARNING
The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Hanger bracket must seat recessed, remove wallboard until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall.
firmly against outlet box.
If the outlet box is
Ceiling
No
less than
7 ft
Floor
Figure 8
Outlet Box
1. Securely attach the hanger bracket to the outlet box using the outlet box screws and washers supplied with the outlet box (Figure 9).
NOTE: Outlet box screws pass through slotted holes of the hanger bracket (Figure 9).
2. Pull the electric wires in the outlet box down through the opening in the hanger bracket and bend wires up and out of the way so that the hanger ball will easily fit into the hanger bracket.
3. Carefully lift the fan and seat the downrod/hanger ball assembly on the hanger bracket that was just attached to the outlet box (Figure 10).Be sure the groove in the ball is lined up with tab on the hanger bracket (Figure 9).
4. After splicing, the wiring should be turned upward and pushed carefully up into the outlet box.
▲
WARNING
Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.
Hanger
Bracket
Screw (2)
Supplied with
Outlet Box
Hanger
Bracket
Tab
Figure 9
Outlet Box
▲
WARNING
To avoid possible shock, do not pinch wires between the downrod/hanger ball assembly and the hanger bracket.
Downrod/Hanger Ball Assembly
Figure 10
8
How to Wire Your Ceiling Fan
WARNING
To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. (Figure 11)
MAIN FUSE BOX
NOTE:
The hand-held remote included with this fan has 16 different code combinations. To prevent possible interference from or to other remote units, simply change the combination code in your transmitter and receiver.
1. To set the transmitter code, remove battery cover by pressing firmly below arrow and sliding cover off. Slide code switches to your choice of up or down position. Factory setting is all up. Do not use this position. With a small screwdriver or ball point pen slide firmly up or down. Replace battery cover on the transmitter (Figure 12).
2. To set the receiver unit code, slide code switches to the same positions as set on your transmitter (Figure 13).
REMOTE TRANSMITTER UNIT DETAIL
RECEIVER UNIT DETAIL
Figure 11
TRANSMITTER CODES
Figure 12
3. Slide the receiver unit into the open end of the
hanger bracket (Figure 14).
Figure 13
RECEIVER UNIT
HANGER BRACKET
Figure 14
9
How to Wire Your Ceiling Fan (continued)
4. Connect green wires from hanger bracket and hanger ball to bare (ground) wire using wire connector supplied. Connect black wire from receiver unit marked “AC IN L” to black supply wire using wire connector supplied. Connect white wire from receiver unit marked “AC IN N” to white supply wire using wire connector supplied. Connect white wire from receiver unit marked “TO MOTOR N” to white wire from fan using wire connector supplied with receiver. Connect black wire from receiver unit marked “TO MOTOR L” to black wire from fan using wire connector supplied. Connect blue wire
from receiver to the blue fan light wire using wire connector supplied. (Figure 15)
Figure 15
HARDWARE USED:
5. After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads to one side of the box and the black leads towards the other side. The wires should be spread apart with the grounded
conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box (Figure 16).
Installing the Canopy Housing
NOTE: This step is applicable after the necessary wiring is completed.
LISTED OUTLET BOX
BLACK-ANT
CONNECTORS
Figure 16
x 6WIRE
WHITE
BLACK
BLUE
GREEN - Ground Wire From Hanger Ball
GREEN - Ground Wire From Hanger Bracket
▲
WARNING
To avoid possible fire or shock, make sure that the electrical wires are completely inside the canopy housing and not pinched between the housing and the ceiling.
1. Remove one of the two shoulder screws in the
hanger bracket. Loosen the second shoulder screw without fully removing it. Assemble canopy by rotating key slot in canopy over shoulder screw in hanger bracket. Tighten shoulder screw. Fully assemble and tighten second shoulder screw that was previously removed (Figure 17a).
2. Securely attach and tighten the canopy screw cover over the shoulder screws in the hanger bracket utilizing the keyslot twist-lock feature (Figure 17b).
10
Figure 17a
Figure 17b
Assembling and Mounting the Fan Blades
1. Position the blade over the blade holder with threaded posts showing. Make sure the bottom edge of the blade is fully seated against the blade arm. With a phillips screwdriver, tighten 3/16-24 x 8 mm washer head screws and fiber washers to secure the blade to the blade arm. (Figure 18)
CAUTION
Do not connect fan blades until the fan is completely installed. Installing the fan with blades assembled may result in damage to the fan blades.
Blade Holder Arm
Blade
Figure 18
HARDWARE USED:
2. Remove and discard the motor stops from the motor assembly by removing the screws. (Figure 19)
3. Secure the blade holders to the motor support
using the 1/4-20 x 14 mm screws through the holes located on the side of the motor support (Figure 20).
NOTE:
Periodically check blade holder hardware and
resecure if necessary.
Motor Assembly
3/16-24x8 mm WASHER HEAD SCREWS
FIBER WASHER
x 15
x 15
Motor Stops
Figure 19
Pan Head Screw (2 per blade holder)
▲
WARNING
To reduce the risk of personal injury, do not bend the blade holders when installing, balancing the blades or cleaning the fan. Do not insert foreign objects in between the rotating blades.
11
HARDWARE USED:
1/4-20x14 mm Pan Head Screw
Figure 20
x 10
Assembling Fan With the Light Kit
NOTE:
1. Disassemble the adapter/switch cup assembly from
2. Remove one of the three screws in the support
If you are assembling your fan without the light kit, please skip to page 14 of this manual.
the switch cup support plate by removing three screws. (Figure 21)
bracket at the bottom of the motor assembly. Slightly loosen the remaining two screws. Assemble
the switch cup support plate to the support bracket using the two key slots in the socket plate. Replace the third screw and securely tighten all three screws (Figure 22).
Switch cup support plate
Adapter/Switch cup assembly
Figure 21
3. Connect the 2-pin connector from motor assembly
to the 2-pin connector from the adapter/switch cup assembly. (Figure 23)
4. Assemble the adapter/switch cup assembly onto the assembled switch cup support plate with three screws. (Figure 24)
Switch cup support plate
Figure 22
Figure 23
Figure 24
12
Loading...
+ 26 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use