Fanimation The Akira FP8000, The Ventana FP8032, The Akira Owner's Manual

Model No. FP8000

OWNER'S MANUAL

READ AND SAVE THESE INSTRUCTIONS

The Akira

™

Ceiling Fan

Finishes: OB and PW

Net Weight 9.6 kg. (21.2 lbs.)

2

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly
diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling
fan before servicing.

4. Do not insert anything into the fan blades while the fan is operating.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Ad di tiona l Saf ety I ns truct ions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without
blades.

2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The
ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or
approved by a licensed electrician.

3. The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. (fan and accessories not to
exceed 50 lbs. or 22.7 kgs.). See page 4 of owner’s manual for support requirements. Consult a qualified electrician if in
doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate
electrical knowledge or experience, have your fan installed by licensed electrician.

6. Suitable for use with solid-state speed controls.

WARNING:To reduce the risk of fire or electric shock, this fan should only be used with Fan Speed Control Part No.

UC7067RC, manufactured by Rhine Electronic Co., Ltd.

WARNING:TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH AN ISOLATING WALL

CONTROL/SWITCH.

WARNING:This product is designed to use only those parts supplied with this product and/or accessories designated

specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in
personal injury or property damage.

WARNING

:

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the

brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship
during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective
fan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costs
incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due
to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service
center. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for all
costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or
workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our
national service center.

4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting,
corroding, tarnishing, or peeling.

5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to
extremes of heat or humidity, or as a result of any modification to the original product.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that
sold the fan or Fanimation.

7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this
warranty.

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must
accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly
packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other
expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to
those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow
limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out
of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you
special legal rights and you may also have other rights that vary from state to state.

10.A certain amount of wobble is normal and should not be considered a problem or a defect.

Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .4

Electrical and Structural Requirements . . . . . . . . . . . . . . . . . .4

How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .5

How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .6

How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .7

How to Install Your Canopy Housing . . . . . . . . . . . . . . . . . . . .8

How to Assembly the Blades & Light Kit . . . . . . . . . . . . . . . . .9

How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

How to Clean Your Ceiling Fan Blades . . . . . . . . . . . . . . . . . .12

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Table of Contents

1. Check to see that you have received the following parts:

NOTE:

If you are uncertain of part description, refer to

exploded view illustration.

This Manual Is Designed to Make it as Easy as Possible for You to Assemble,

Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

• One Phillips head screwdriver

• One stepladder

• Three wire connectors (supplied)

3

Installed Wire Length Wire Size A.W.G.

41.tf 05 ot pU

21.tf 001-05

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check
mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should
you be interrupted.

Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 4). If you
feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.

Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any
accessories designated specifically for use with this
product by Fanimation. Substitution of parts or
accessories not designated for use with this product
by Fanimation could result in personal injury or
property damage.

WARNING

!

WARNING

!

• One wire stripper

• One 1/4” blade

screwdriver

Materials

Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be a
3-conductor (2-wire with ground) of the following size:

NOTE:

Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are
missing contact your local retailer.

• Fan Motor Assembly

• Hanger Bracket Assembly with

screws

• Downrod/Hanger Ball Assembly

• Ceiling Canopy

• Canopy Screw Cover Assembly

• Motor Coupling Cover Assembly

• Blade Arm Set (5)

• Blade Set (5)

• Housing Light Kit Assembly

• Socket Plate Assembly

• Two 60W Candelabra Light Bulbs

• Glass

• C24 Remote Control

• Receiver Unit

• Hardware bags:

– 3/16-24 x 7.5mm

(blade to blade holder)

Washer Head Screw

– 3/16” Fiber Washer

(blade to blade holder)

– 1/4”-20 x 14mm

(blade arm to motor)

Pan Head Screw

– Phillips Screwdriver, 4�

– Four Wire Connectors

– Balance Kit

HANGER
BRACKET
ASSEMBLY
W/SCREWS

DOWNROD/
HANGER BALL
ASSEMBLY

CEILING
CANOPY

C24 REMOTE
CONTROL

RECEIVER
UNIT

CANOPY
SCREW
COVER
ASSEMBLY

MOTOR
COUPLING
COVER

FAN MOTOR
ASSEMBLY

HARDWARE BAG

SOCKET
PLATE
ASSEMBLY

TWO 60-WATT
CANDELABRA
LIGHT BULBS

BLADE ARM SET (5)

HOUSING
LIGHT KIT
ASSEMBLY

GLASS

BLADE SET (5)

4

Energy Efficient Use of Ceiling Fans

Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the
ceiling fan. Here are a few tips to ensure efficient
product performance.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the
middle of the room and at least 7 feet above the floor
and 18 inches from the walls. If ceiling height allows,
install the fan 8 - 9 feet above the floor for optimal
airflow. Consult your Fanimation Retailer for optional
mounting accessories.

Turn Off When Not in the Room

Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the

counterclockwise direction. The airflow produced by
the ceiling fan creates a wind-chill effect, making you
“feel” cooler. Select a fan speed that provides a
comfortable breeze, lower speeds consume less
energy.

Winter Season: Reverse the motor and operate the
ceiling fan at low speed in the clockwise direction.
This produces a gentle updraft, which forces warm air
near the ceiling down into the occupied space.
Remember to adjust your thermostat when using your
ceiling fan - additional energy and dollar savings
could be realized with this simple step!

Electrical and Structural Requirements

If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and
remove the existing light fixture.

Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 lbs.
Figure 1 depicts different structural configurations
that may be used for mounting the outlet box.

To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.

Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.

WARNING

!

WARNING

!

To reduce the risk of fire, electrical shock, or
personal injury, mount fan to outlet box marked
acceptable for fan support of 22.7 kg (50 lbs) or less.
Use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to
be replaced. Consult a qualified electrician if
in doubt.

WARNING

!

Figure 1

CEILING

CEILING JOIST

2" x 4"

OUTLET BOX

Figure 1

5

How to Assemble Your Ceiling Fan

1. Remove the hanger ball portion from the

downrod/hangerball assembly by loosening the set
screw in the hanger ball until the ball falls freely
down the downrod. Remove the pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in Step 4
(Figure 1).

2. Loosen the two set screws in the downrod support.

Route black, blue and white lead wires through the
downrod (Figure 2).

3. Position downrod support and align the clevis pin

holes in both parts. Install the clevis pin and secure
with the hairpin clip. Tighten the two set screws
and locking nuts in the downrod support (Figure 3).

4. Route wires through motor coupling cover, canopy

screw cover and canopy (Figure 4).

5. Reinstall the hanger ball on t he downr od as

follows.Route the three 80-inch wires through the
hanger ball. Position the pin through the two holes
in the downrod and align the hanger ball so the pin
is captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin.
Securely tighten the set screw in the hanger ball.
A loose set screw could create fan wobble
(Figure 5).

Figure 5

Figure 3

Figure 4

Figure 2

DOWNROD

SET SCREW

DOWNROD

DOWNROD SUPPORT

HAIRPIN CLIP

PIN

BLACK, BLUE AND
WHITE LEADS

DOWNROD

SET SCREWS AND
LOCKING NUTS (2)

SET SCREWS AND

LOCKING NUTS (2)

CLEVIS PIN

HANGER BALL

SCREWDRIVER

SET SCREW

PIN

BLACK, BLUE &
WHITE LEADS

CANOPY

CANOPY COVER

MOTOR COUPLING
COVER

BLACK, BLUE &
WHITE LEADS

CANOPY

GROOVE

HANGER BALL

DOWNROD