Page 1
CWRL4 Wall Control
SPECIFICATION and INSTRUCTION SHEET
DESCRIPTION: One Ceiling Fan & Light, 3 Speed Wall Control with Learn Receiver
ELECTRICAL SPECS:
FAN MODELS USED:
120 Volts, 60 Hertz, Fan 1.0 amp, Light Rating 190W (max.)
Incandescent or Halogen, 5 Wire Installation
May be used in conjunction with CRL4 Remote Control
See Catalog or visit our website www.fanimation.com for more information
IMPORTANT: YOU MUST SET YOUR CEILING FAN TO HIGH SPEED AND LIGHT KIT
(IF ANY) TO THE ON POSITION BEFORE OPERATING YOUR REMOTE CONTROL.
NOTE: If fan or supply wires are different colors than indicated,
have this unit installed by a qualified electrician.
WARNING
Ceiling
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advise, as it must be
grounded for safe operation.
INSTALLING THE RECEIVER:
Ceiling fan must be set at HIGH speed and light kit (If any) at 1.
the ON position by pressing the “Light Switch” after installation.
Install Receiver in the Hanger Bracket:2.
• Slide remote Receiver into the Hanger Bracket (Figure 1).
• Connect wires as indicated: (Figure 2)
–Green Hanger Bracket and Hanger Ball wires to BARE (ground) wire.
–BLACK Receiver Unit wire (AC IN L) to BLACK supply wire.
–WHITE Receiver Unit wire (AC IN N). to WHITE supply wire.
–WHITE Receiver Unit wire (TO MOTOR N) to WHITE fan wire.
–BLACK Receiver Unit wire (TO MOTOR L) to BLACK fan wire.
–BLUE Receiver Unit wire (FOR LIGHT DOWN) to BLUE light wire.
• Position all connected wires and receiver antenna to allow
installation of ceiling canopy.
• Using canopy screws threaded into the hanger bracket reinstall
ceiling canopy.
AC120V 60HZ
BLACK (AC IN L)
BLACK (AC IN L)
WALL
CONTROL
GREEN / YELLOW
GROUND WIRE
BLACK (TO MOTOR L)
BLACK
BLACK
BLACK (AC IN L)
Check to see that all connections are tight, including ground,
and that no bare wire is visible at the wire connectors,
except for the ground wire. Do not operate fan until the
blades is in place. Noise and fan damage could result.
Bracket
(Open End)
NOTE:
Receiver wires omitted for clarity.
Figure 2
Figure 1
INPUT
WHITE (AC IN N)
AC SUPPLY
BLUE (FOR LIGHT)
BLACK (TO MOTOR L)
WHITE (TO MOTOR N)
BARE
GREEN
WARNING
Receiver Unit
BLUE
BLACK
WHITE
Figure 3
Figure 2
INSTALLING THE WALL CONTROL (Figure 3):
With power still off, remove existing wall plate, disconnect and 1.
remove the toggle switch from wall junction box. Save the 2
screws from the toggle switch.
Using the supplied wire connectors, make the electrical 2.
connections to the new wall control (transmitter) unit.
NOTE: Place control ON/OFF slide switch to the OFF position.
LEARNING
BUTTON
LIGHT
DIMMER
FUNCTION
SELECT
SWITCH
Carefully push all connected wires inside wall switch box. 3.
Secure wall control unit with 2 screws previously removed. 4.
Push and click the face plate onto the wall control (transmitter).5.
Restore power6.
LEARN MODE PROCESS:
Control and receiver have been factory programmed. If replacing the 1.
transmitter or receiver, the learn mode process will need to be used.
After installing the unit and restoring power to your fan, press 2.
and hold the ”LEARNING BUTTON” 1~3seconds with a ball-point
pen or similar object. Make sure ON/OFF slide switch is in the
ON position. FAN will turn off and then turn to medium speed,
which indicates that the learning process has completed.
IMPORTANT: You must press the “LEARNING BUTTON”
within 60 seconds of restoring power to the fan. (Figure 4)
If light kit has CFL bulbs, please slide the “light dimmer function 3.
select switch” to “O” position. If installed incandescent light bulbs
onto ceiling fan, please slide the “light dimmer function select
switch” to “I” position.
Please note, the wall control can learn multiple receivers. 4.
60 second time limit should eliminate need for this.
10983 Bennett Parkway
Zionsville, IN 46077
(888) 567-2055 • FAX (866) 482-5215
Outside U.S. call (317) 733-4113
Visit Our Website @ www.fanimation.com
Figure 3 Figure 4
WALL CONTROL FUNCTIONS:
ON/OFF- Press and release the light button
immediately to turn on or off the light.
Press and hold the light button to dim or
brighten light to the desired level and release
NOTE: feature cannot be used with CFL bulbs
OFF
Turns off the fan
H
Turns fan to high speed
M
Turns fan to medium speed
L
Turns fan to low speed
OFF ON
L
Turns off all power to your fan.
Learn mode button; Connects transmitter & receiver
IO
ON/OFF for light dimmer function
Copyright 2010 Fanimation
OFF ON
H
M
L
OFF
IOL
2010/02
Loading...