Manual
www.fanatec.com
Straights are for fast cars
Turns are for fast drivers
Thank you for choosing
To get the most out of and before using your new CSL Elite Wheel Base, please
read this manual for important information regarding your health and how to
safely use this product. This manual can also be used as a great tool for future
reference.
3
INDEX
1. General ............................................................................................................... 5-6
2. Introduction ........................................................................................................ 7
3. Compatibility ....................................................................................................... 7
4. Preparation ......................................................................................................... 8
4.1 Package contents ........................................................................................ 8
5. Assembly ............................................................................................................. 9-18
5.1 Plan your conguration .............................................................................. 9
5.2 Mounting the CSL Elite Wheel Base by Table Clamp ............................... 9-10
5.3 Hardmounting the CSL Elite Wheel Base .................................................. 11
5.4 Attaching a Fanatec CSL Steering Wheel .................................................. 12-13
5.5 Take o a Fanatec CSL Steering Wheel ..................................................... 13
5.6 Attaching a Fanatec ClubSport Steering Wheel ....................................... 14
5.7 Take o a Fanatec ClubSport Steering Wheel ......................................... 15
5.8 ClubSport Static Shifter Paddles (CS SSP) ............................................... 16
5.9 Connections ................................................................................................. 16-18
5.10 Drilling Template ........................................................................................ 18
6. Functions & Features ......................................................................................... 19-33
6.1 Firmware and driver update ........................................................................ 19-27
6.2 Start-Up procedure ...................................................................................... 28
6.3 Tuning menu ................................................................................................. 29-32
6.4 Revolution Lights (RevLEDs) ..................................................................... 32
6.5 Cooling system ............................................................................................ 33
7. Electronic operation ........................................................................................... 34-37
7.1 Hotkeys ......................................................................................................... 34-37
8. Cleaning .............................................................................................................. 38
9. Troubleshooting ................................................................................................. 38-39
10. Serial number..................................................................................................... 40
11. Trademarks......................................................................................................... 40
12. Ecology Advice .................................................................................................. 41
13. FCC Compliance ................................................................................................ 42
14. CE Compliance .................................................................................................. 42
15. Warranty ............................................................................................................. 43
4
WARNING! Photosensitive Seizures
A very small percentage of people may experience a seizure when exposed to certain visual im-
ages, including ashing lights or patterns that may appear in video games. Even people who have
no history of seizures or epilepsy may have an undiagnosed condition that can cause these „photosensitive epileptic seizures” while watching video games. These seizures may have a variety
of symptoms, including light-headedness, altered vision, eye or face twitching, jerking or shaking
of arms or legs, disorientation, confusion, or momentary loss of awareness. Seizures may also
cause loss of consciousness or convulsions that can lead to injury from falling down or striking
nearby objects. Immediately stop playing and consult a doctor if you experience any of these
symptoms. Parents should watch for or ask their children about the above symptoms – children
and teenagers are more likely than adults to experience these seizures.
The risk of photosensitive epileptic seizures may be reduced by taking the following precautions:
• Sit farther from the TV screen.
• Use a smaller TV screen.
• Play in a well-lit room.
• Do not play when you are drowsy or fatigued.
If you or any of your relatives have a history of seizures or epilepsy, consult a doctor before playing.
WARNING! Musculoskeletal disorders
Use of game controllers, keyboards, mice, or other electronic input devices may be linked to serious injuries or disorders. When playing video games, as with many activities, you may experience
occasional discomfort in your hands, arms, shoulders, neck, or other parts of your body. However,
if you experience symptoms such as persistent or recurring discomfort, pain, throbbing, aching,
tingling, numbness, burning sensation, or stiness, DO NOT IGNORE THESE WARNING SIGNS.
PROMPTLY SEE A QUALIFIED HEALTH PROFESSIONAL, even if symptoms occur when you
are not playing a video game. Symptoms such as these can be associated with painful and sometimes permanently disabling injuries or disorders of the nerves, muscles, tendons, blood vessels,
and other parts of the body. These musculoskeletal disorders (MSDs) include carpal tunnel syndrome, tendonitis, tenosynovitis, vibration syndromes, and other conditions.
While researchers are not yet able to answer many questions about MSDs, there is general
agreement that many factors may be linked to their occurrence, including medical and physical
conditions, stress and how one copes with it, overall health, and how a person positions and
uses their body during work and other activities (including playing a video game). Some studies
suggest that the amount of time a person performs an activity may also be a factor. If you have
questions about how your own lifestyle, activities, or medical or physical condition may be related
to MSDs, see a qualied health professional.
5
ATTENTION
• The device must not be exposed to rain or humidity in order to avoid risk of re and the danger
of electric shock.
• Operating temperature: 15°C – 35°C room temperature
•
The recommended operation time of the wheel with continuous force feedback activity is 1 hour.
Let the wheel cool down for a few minutes before you continue.
• Long playing may cause health risks. Take a break of 5 minutes every 20 minutes, and do not
play for more than 2 hours per day.
• We strongly advise you to not drive a vehicle immediately after using a video game.
• Utilization of the vibration and Force Feedback function may cause damage to your health.
• In case of interference with other wireless 2.4 GHz devices, the interfering devices must be
removed or switched o.
•
Not intended for children under the age of 6 years. Contains small pieces. Danger of swallowing!
• Do not open the casing of the device.
• This device contains components that cannot be repaired by the user, opening will void the
warranty.
WARNING! Electrical Safety
The CSL Elite Wheel Base must be connected to an appropriate power source:
• For the used CSL Elite Wheel Base use only the power supply and AC power cord that came
with your CSL Elite Wheel Base or that you received from an authorized repair center.
•
For the used CSL Elite Wheel Base do not use non-standard power sources, such as generators
or inverters, even if the voltage and frequency appear acceptable. Only use AC power provided
by a standard wall outlet.
• To avoid damaging the CSL Elite Wheel Base:
Do not expose your CSL Elite Wheel Base to sources of heat.
•
When connecting and / or disconnecting any Steering Wheel (e.g. Porsche 918 RSR or Universal
Hub) to / from CSL Elite Wheel Base take care of the pins inside the quick release.
• Do not try to use the CSL Elite Wheel Base with other Steering Wheels than Fanatec Steering
Wheels.
• Do not try to use the CSL Elite Wheel Base with an external power source dierent from the
power supply packaged with the CSL Elite Wheel Base or received from authorized repair center.
• Unplug the power cord of your CSL Elite Wheel Base during storms or when unused for long
periods of time to protect also your CSL Elite Wheel Base.
•
If the CSL Elite Wheel Base becomes damaged in any way, stop using it immediately and contact
Fanatec Customer Support.
GENERAL
1
6
GENERAL NOTES
• Fanatec Steering Wheels like the BMW M3 GT2, the Formula Black and Formula Carbon, the
Porsche 918 RSR, the Universal Hub and others which might be mentioned in this manual are
not included within the ClubSport Wheel Base package and sold separately.
•
Additional peripheral devices like shifters, pedals, LED displays and others which might be
mentioned in this manual are not included within the ClubSport Wheel Base package and sold
separately.
•
This manual explains a lot about assembly, connections and functions related to Fanatec
Steering Wheels, other additional peripheral devices and also about PC or console (Xbox
One) functionalities but this manual is not a replacement for the manuals corresponding to the
products! Read the quick guides or user manuals for the other products as well!
• All specications in this document are subject to change. Especially the CSL Elite Wheel Base
rmware or the PC driver might be changed or updated to implement new features or for general
improvements.
•
The warranty does not include defects that are due to commercial use of the product. See
chapter “Warranty” at the end of this user manual as well as the terms & conditions on
www.fanatec.com for more details.
7
INTRODUCTION
COMPATIBILITY
You have purchased an innovative product which enables you to use dierent
steering wheels in simracing. The CSL Elite Wheel Base provides high steering
accuracy, strong force feedback brushless servo motor, smooth belt drive and
1080° rotation angle built into a high quality Wheel Base with automotive-grade
quick release.
Select the Steering Wheel of your choice compatible to your CSL Elite Wheel
Base such as the CSL Steering Wheel P1 for Xbox One, BMW M3 GT2, the
Formula Black and Formula Carbon, the Porsche 918 RSR and the Universal
Hub for Xbox One. Select your Fanatec Steering Wheels from ClubSport se-
ries and CSL series according to your personal driving style – it is simply your
choice!
The CSL Elite Wheel Base (CSL E WB) can be used with the CSL Steering
Wheel P1 for Xbox One and also with the ClubSport Steering Wheels like the
BMW M3 GT2, the Formula Black and Formula Carbon, the Porsche 918 RSR,
the ClubSport Universal Hub for Xbox One and other peripheral devices from
Fanatec like pedals, shifters and handbrake. Especially look for other products
from the Fanatec CSL platform and ClubSport platform!
The CSL Elite Wheel Base can be used on PC and Xbox One (requires a Fanatec
Steering Wheel designed for Xbox One; Xbox One Mode to be activated).
IMPORTANT: Before rst use the CSL Elite Wheel Base must be up-
dated to the latest rmware version which is available on our website
www.fanatec.com/support. See chapter ‘Firmware and driver update’ for
more details!
2
3
8
PREPARATION
4.1 Package contents
4
CSL Elite Wheel Base
Table clamp screw with handle
Table clamp
Power supply (dierent versions for
Europe EU, United States of America
US, Australia AU and Japan JP)
USB connection cable with straight plug
O-Ring (O1)
Quick Guide
9
ASSEMBLY
5.1 Plan your conguration
To operate the CSL Elite Wheel Base, a Fanatec Steering Wheel with quick release is required (e.g. the BMW M3 GT2, the Porsche 918 RSR or the Univer-
sal Hub). Just plug your steering wheel onto the quick release and get started.
Connect the CSL Elite Wheel Base to your PC or PlayStation 3 system by using
the USB cable.
IMPORTANT: Use only the USB cable with the straight plug which is
pack- aged with your CSL Elite Wheel Base to avoid damages on the CSL
Elite Wheel Base electronics!
Please check chapter ‘Connections’ to see which kind of peripheral devices
must be connected to which socket at the CSL Elite Wheel Base.
Additional peripheral devices like pedals or shifters are not strictly required but
will give the user a more similar feeling like driving a race car. We recommend
to use shifters and pedals from the Fanatec ClubSport platform like the ClubSport Shifter SQ (CSS SQ), the ClubSport Static Shifter Paddles (CS SSP) or
the ClubSport Pedals (CSP) and more. Visit our Webshop at www.fanatec.com
for more compatible products.
5.2 Mounting the CSL Elite Wheel Base using the Table Clamp
Insert the threaded rod with handles into the table clamp.
5
10
Turn the table clamp with threaded rod into the counterpart in center of CSL Elite Wheel Base bottom side.
Slide the CSL Elite Wheel Base onto table plate until the
limiter blocks stop sliding at edge of table, table clamp
has to be below table plate.
Tighten the table clamp by turning the threaded rod.
While tightening the table clamp please monitor and adjust the clamp feet to be well aligned with the table plate
and pressing at onto the table plate surface.
11
5.3 Hardmounting the CSL Elite Wheel Base
The CSL Elite Wheel Base oers a three-point hardmount opportunity on the
bottom side of the CSL Elite Wheel Base, see marked on the right hand side
picture below. To hardmount the Wheel Base rst disassemble the two blocks
from the bottom side with Allen Key 3 mm (not included), see highlighted on the
left hand side picture below:
IMPORTANT: Used screws have to be good quality M6 screws. Chose
the screw length so that the thread does not reach more than 16 mm into
the wheel base. Example: If your table thickness is 20 mm the screw must
not exceed a total thread length of 36 mm! Always use all three hard-
mount points to allow a proper and stable xation and avoid damages!
Table
max 16mm
X
To hardmount the CSL Elite Wheel Base to a table or rig by screws please
nd the printable drilling template in the download area of our website
www. fanatec.com.
12
Slide steering wheel onto
wheel base axle
Turn the steering wheel top side down to see the bottom side of the clamp
ring to follow next step below
Push steering wheel until the screw hole matches
with hole on wheel base axle
Align wheel base axle, to correct position
5.4 Attaching a Fanatec CSL Steering Wheel
Use clamp ring screw (M6 x 18mm at head)
and Allen Key from box content
13
5.5 Take o a Fanatec CSL Steering Wheel
Turn out the xing screw and open clamp ring mechanism, use only the Allen Key which comes with the
steering wheel!
Slide steering wheel o wheel base axle
Store clamp ring screw and Allen Key safely
Turn in screw to x clamp ring mechanism, use only
the Allen Key which comes with the steering wheel!
IMPORTANT: Tighten only by using the short lever of Allen Key!
14
5.6 Attaching a Fanatec ClubSport Steering Wheel
Remove storage pin
Align CSL Elite Wheel Base axle,
to correct position
Press together or “pinch”
and hold quick release mechanism
Slide rim onto CSL Elite Wheel Base axle
Now release the sleeve of the
quick release mechanism
IMPORTANT: Please mind not to use high force to attach the steering
wheel to avoid damages! It is possible to attach the steering wheel on
the last 8 mm you need a little force because of the O-ring which avoids
shaking steering wheels.
15
Pinch and hold
quick release mechanism
Slide rim o CSL Elite Wheel Base axle
Place rim face down on table
Insert storage pin
Now release the sleeve of the
quick release mechanism
5.7 Take o a Fanatec ClubSport Steering Wheel
16
IMPORTANT: ClubSport Static Shifter Paddles (CS SSP) sold sepa-
rately and not included within the CSL Elite Wheel Base package content.
Mounting screws for ClubSport Static Shifter Paddles included within the
package of ClubSport Static Shifter Paddles.
5.9 Connections
To connect additional peripheral devices like shifters, pedals or LED displays to the ClubSport Wheel
base there is a row of connector sockets at the lower backside of the CSL Elite Wheel Base:
5.8 ClubSport Static Shifter Paddles (CS SSP)
At the front plate of the CSL Elite Wheel Base
there are four holes with gears which are used
for mounting the ClubSport Static Shifter Paddles
(CS SSP) as shown in the picture below:
IMPORTANT: Use only the connection cables which are packaged
with the peripheral devices! Peripheral devices are not included and sold
separately!
17
5.9.1 USB
The USB port is used to connect the CSL Elite Wheel Base to the PC or Xbox
One.
IMPORTANT: Use only the USB cable with the straight plug which is
packaged with your CSL Elite Wheel Base to avoid damages on the CSL
Elite Wheel Base electronics!
5.9.2 SHIFTER1
The SHIFTER1 port is used to connect H-pattern shifters to the CSL Elite Wheel
Base, e.g. the ClubSport Shifter (CSS) or the ClubSport Shifter SQ (CSS SQ)
in H-pattern mode. Also sequential shifters can be connected to this port and
will be detected correctly. Note: Sequential shifters connected to this port can
be mapped identically to the shifter paddles at the Fanatec Steering Wheels
like the BMW M3 GT2, the Formula Black or Formula Carbon, the Porsche 918
RSR or the Universal Hub with assembled shifter paddle boxes by PC driver
settings (see chapter ‘PC driver’ of this user manual).
5.9.3 SHIFTER2
The SHIFTER2 port is used to connect sequential shifters (SQ) to the CSL Elite
Wheel Base, e.g. the ClubSport Shifter SQ (CSS SQ) in SQ mode or the Club-
Sport Static Shifter Paddles (CS SSP). Note: Sequential shifters connected to
this port can be mapped identically to the shifter paddles at the Fanatec Steering Wheels like the BMW M3 GT2, the Formula Black or Formula Carbon, the
Porsche 918 RSR or the Universal Hub with assembled shifter paddle boxes
by PC driver settings (see chapter ‘PC driver’ of this user manual). Attention:
H-pattern shifters will not work on SHIFTER2 port!
5.9.4 PEDAL
The PEDAL port is used to connect pedals to the CSL Elite Wheel Base, e.g.
the ClubSport Pedals (CSP), the CSR Pedals (CSR P) or the CSR Elite Pedals
(CSR EP).
5.9.5 HANDBRAKE
The HANDBRAKE port is used to connect the ClubSport Handbrake (CS HB)
to the CSL Elite Wheel Base.
18
ATTENTION: Please download and print the drilling template for hard-
mounting the CSL Elite Wheel Base from the download area of our website www.fanatec.com.
78,4
66
270
6,5
21,2
220
CSL E WB
1
78,4
66
CSL E WB
2
5.9.6 POWER
The POWER connector is used to connect the power supply to the CSL Elite
Wheel Base.
IMPORTANT: Please use only the power supply and AC power cord
that came with your CSL Elite Wheel Base or that you received from an
authorized repair center. See ‘Electrical Safety’ in Chapter 1 ‘General’ for
more details!
5.10 Drilling Template
19
The CSL Elite Wheel Base has specic rmware handling the device communication to PC or Xbox One as well as to other hardware peripheral devices
like shifters and pedals. This rmware provides dierent functions for the user.
6.1 Firmware and driver update
The rmware and the PC driver can be updated to newer versions by Fanatec
for software bug xing or introduction of new features and compatibilities.
Before rst use the CSL Elite Wheel Base has to be updated to the latest rm-
ware version which is available on our website www.fanatec.com/support.
You also have to use the latest PC driver version in order to use the CSL Elite
Wheel Base on a PC.
Run the downloaded le(s) and follow the instructions shown on the screen.
See more detailed description later in this user manual chapter.
IMPORTANT: The CSL Elite Wheel Base is secured by rmware and
by driver so that usually it is not possible to install wrong rmwares on
the CSL Elite Wheel Base! Do not try to force installation of any wrong
rmware to the CSL Elite Wheel Base to avoid damages.
IMPORTANT: After rmware update the center position of the CSL
Elite Wheel Base has to be manually calibrated again. This is also indicated by the LED display of the attached steering wheel showing ‘CAL’. This
appearance will be gone after manual calibration of the wheel center. See
chapter ‘Hotkeys’
‘Wheel center calibration’ for more details.
IMPORTANT: After rmware update the H-pattern shifters connected
to the CSL Elite Wheel Base has to be manually calibrated again. See
chapter ‘Hotkeys’
‘Shifter calibration mode’ for more details.
FUNCTIONS & FEATURES
6
20
6.1.1 PC driver
The PC driver is a very helpful tool as it
can assist the user to do functional tests,
adjustments and update procedure on the
CSL Elite Wheel Base.
When you start the driver this window as
shown on the right hand side will appear
and show all connected USB devices:
Double-click the CSL Elite Wheel Base to
go ahead and see the complete menu.
The next appearing menu ‘function test’
then is depending on the attached Fanatec
Steering Wheel. For the manual there is used the CSL Steering Wheel P1 for
Xbox One as an example, see pictures below:
This window shows you a lot of dierent information and gives possibilities to
test the currently used hardware and peripherals:
21
Indicator bar shows the current Steering
Wheel position, the upper box shows the position in digits, the lower box shows the position
as an angle (positive and negative angle related to the calibrated wheel center position).
The button ‘display test’ activates a signal ow on the LED display of the attached Fanatec Steering Wheel and activates all LED display segments so you
can check if all LED display segments work properly.
The button ‘FFB test’ starts a force feedback test and activates the motor of the
CSL Elite Wheel Base to check proper functionality.
The button ‘Wheel Base RevLEDs test’ starts a signal ow on the LED bar on
the upper frontside of the CSL Elite Wheel Base and activates them to test
proper functionality of each single LED.
The button ‘Steering Wheel RevLEDs test’ starts a signal ow on the LED bar
on the Steering Wheel top side and activates them to test proper functionality
of each single LED. This is only available for Steering Wheels which have RevLEDs, refer to the product description of the used Steering Wheel.
The button ‘Vibration Test’ starts a vibration signal to activate the vibration mo-
tors inside the Fanatec Steering Wheels. This is only available for Steering
Wheels which have vibration motors inside, refer to the product description of
the used Steering Wheel.
The three indicators ‘Clutch’, ‘Brake’ and ‘Throttle’ show the
current activation and position of these single pedals by a
blue bar moving up and down. Therefore the pedals must be
connected to the CSL Elite Wheel Base.
Note: Every pedal lever must be pressed down completely to
auto-calibrate the lever movement distance each time when
power resumes.
The ‘D-pad’ arrows (up, down, left, right) change their colour from black to blue when the corresponding direction is
pressed on the attached Fanatec Steering Wheel.
The ‘Rotary Encoder’ boxes ash blue when turning left or
right the FunkySwitch
TM
(clockwise or counter-clockwise).
22
The ‘2GS’ indicator shows the activation of the 2GS (two
gears shifter, sequential shifter, SQ) by lling the two little
squares with blue colour, depending on activated shifting
up or shifting down. This can be for example the ClubSport
Static Shifter Paddles (CS SSP) or the ClubSport Shifter SQ
(CSS SQ) in sequential mode if these are not mapped to the
Steering Wheel shifter paddles.
The ‘H-pattern’ indicator shows the activation of the 6GS,
7GS or 8GS (six gears shifter, seven gears shifter or eight
gears shifter) by lling the little squares with blue colour,
depending on activated shifting position. This can be for ex-
ample the ClubSport Shifter (CSS) or ClubSport Shifter SQ
(CSS SQ). Therefore the H-pattern shifter must be calibrated.
See chapter ‘Hotkeys’
‘Shifter calibration mode’ for more
details
The biggest area in this window is the upper right section of this view. There
is shown a scheme of the attached Fanatec Steering Wheel with all buttons. If
you press one of the buttons on the attached Steering Wheel the corresponding
button will be highlighted with a blue spot as long as the button is physically
activated. Please note that this view is depending on the attached Fanatec
Steering Wheel and also note that for the Universal Hub all button boxes, the
shifter paddles and the FunkySwitch
TM
are shown even if they are not physically
attached. See example picture for the Universal Hub on the right hand below:
23
If you go to the PC driver page ‘Settings’ you will see this window:
There are two dierent slider bars in the section ‘Steering wheel’:
The upper bar ‘Wheel angle’ can adjust the maximum turning angle of the CSL
Elite Wheel Base, so the functionality is identical with the option ‘SEN’ in tuning
menu (see chapter ‘Tuning Menu’ of this manual for more detailed information).
Please note that in tuning menu the value for ‘SEN’ must be set to ‘OFF/Aut’ to
allow the PC driver to take the control. If in tuning menu ‘SEN’ is set to any other
value than ‘OFF/Aut’ the value set in tuning menu is applied and valid and the
PC driver has no inuence.
The lower bar ‘Dampering strength’ is an additional ne tuning possibility for the
tuning menu option ‘DPR’ (see chapter ‘Tuning Menu’ of this manual for more
detailed information).
In section ‘Pedals’ there is only the one checkbox called ‘Combined pedals’. Ac-
tivate this checkbox if the game or software uses only one input (I/O) for brake
and throttle pedal signals (negative signal for brake, positive signal for throttle).
This might solve problems especially with older games.
In section ‘Gear shifts’ there is only one checkbox called ‘Map sequential shift-
er to the shifter paddles’. Usually shifters connected to the SHIFTER2 port
are mapped to dierent inputs (I/Os) than the shifter paddles at the Fanatec
Steering Wheels. If you want to change the mapping so that the used inputs for
these shifters are identically mapped as for the Fanatec Steering Wheel shifter
paddles activate this checkbox. This might be a good option when using the
ClubSport Static Shifter Paddles (CS SSP).
24
If you go to the PC driver page ‘Update’ you will see this window:
In this window you can see the following informations:
• Currently installed and used PC driver version
•
Currently installed and used rmware version on the CSL Elite Wheel
Base
• Quick link to the Fanatec homepage www.fanatec.com
Below the shown information there is the button ‘Update CSL Elite Wheel Base
Firmware’. When pressing this button the rmware update process for the CSL
Elite Wheel Base will be started (see more detailed description in chapter ‘Firm-
ware update procedure’ below in this user manual).
6.1.2 Firmware update procedure
To initiate the rmware update the CSL Elite Wheel Base rst has to be be
connected to the PC by USB cable and then it has to be switched to Bootloader
mode. You can switch to Bootloader mode in two dierent ways:
• by PC driver, on page ‘Update’ press the button ‘Update CSL Elite Wheel
Base Firmware’ when the CSL Elite Wheel Base is switched ON, see
previous chapter ‘PC driver’
• by pressing the ON/OFF button “
”
on the front plate of the CSL Elite
Wheel Base for about 8 seconds when the CSL Elite Wheel Base is
switched OFF.
25
When the Bootloader mode is active the
fan is OFF and the LED above the ON/
OFF button “
” on the frontplate of the
CSL Elite Wheel Base is ashing blue.
On the PC screen this window will ap-
pear automatically as shown on the right
hand side
:
Click on the upper button ‘Start rmware updater’.
Then a new window will appear as
shown on the right hand side:
Connect to your CSL Elite Wheel
Base by pressing the button ‘Connect’.
26
When the Wheel Base Updater is
connected to the CSL Elite Wheel
Base the buttons ‘Load Hex File’ and
‘Flash Firmware’ are available as
shown on the right hand side:
Use button ‘Load Hex File’ to browse
and select the wanted rmware le
(.hex). Usually the latest available
rmware found is already pre-selected and this step can be skipped.
When the pre-selected rmware le
(.hex) is ok or the wanted rmware
le (.hex) is chosen press button
‘Flash Firmware’ to execute the rm-
ware update.
The rmware update is proceeding.
You can see the progress bar becom-
ing green as shown on the right hand
side:
27
When the update is done the CSL
Elite Wheel Base will restart automat-
ically after rmware update is completely nished as shown on the right
hand side:
The CSL Elite Wheel Base switches
o and automatically on again and
then will execute the calibration run.
IMPORTANT: Do not touch the
attached Steering Wheel while the
CSL Elite Wheel Base restarts and
performs the initial calibration run
to avoid injuries and/or miscalibration!
IMPORTANT: The CSL Elite Wheel Base is secured by rmware and
by driver so that usually it is not possible to install wrong rmwares on
the CSL Elite Wheel Base! Do not try to force installation of any wrong
rmware to the CSL Elite Wheel Base to avoid damages.
IMPORTANT: After rmware update the center position of the CSL
Elite Wheel Base has to be manually calibrated again. This is also indicated by the LED display of the steering wheel showing ‘CAL’. This appearance will be gone after manual calibration of the wheel center. See
chapter ‘Hotkeys’
‘Wheel center calibration’ for more details.
IMPORTANT: After rmware update the H-pattern shifters connected
to the CSL Elite Wheel Base has to be manually calibrated again. See
chapter ‘Hotkeys’
‘Shifter calibration mode’ for more details.
28
6.2 Start-Up procedure
The CSL Elite Wheel Base has an improved and faster start-up procedure:
ATTENTION: When initialisation and auto calibration of the CSL Elite
Wheel Base is in progress never touch the attached steering wheel in order to avoid injuries or incorrect calibration!
• Step1: Press the ON/OFF button “
”
at the front plate of
the CSL Elite Wheel Base, marked in the picture on the
right hand side:
•
Step2: The fans start working, the LED above the ON/OFF
“
”
Button is lit red.
•
Step3: The CSL Elite Wheel Base starts turning to the right side (clockwise)
until mechanical limit is reached. Then it runs back to the the left side
(counter clockwise) and stops…
at the center position (0°) if wheel center was manually
calibrated before. Note: If SPR is set to low values or ‘000’ the
CSL Elite Wheel Base will stop in a dierent position after
calibration run.
at about -60° on the left hand side if wheel center was not yet
calibrated (e.g. after rmware update; see description above in
this chapter)
• Step4: The currently installed rmware version is shown
on the LED display of the Fanatec Steering Wheel for a
moment as shown on the picture on the right hand side:
•
Step5: If the wheel center was not yet calibrated ‘CAL’
is blinking on the LED display of the Steering Wheel as
shown on the picture on the right hand side:
Do manual wheel center calibration as described
in chapter ‘Hotkeys’ of this manual.
The CSL Elite Wheel Base is ready to use
after manual wheel center calibration.
• Step6: CSL Elite Wheel Base is ready to use. If the wheel center was
already calibrated before step 5 can be skipped and the CSL Elite Wheel
Base is ready to use immediately. If you use a H-pattern shifter the Wheel
Base rmware will request to calibrate the gears automatically now. Refer
to chapter ‘Shifter calibration mode later in this user manual’.
29
6.3 Tuning menu
The tuning menu is shown on the tuning display on the Fanatec Steering Wheels
after activating the tuning menu by pressing the tuning menu button (see chapter ‘Hotkeys’ of this user manual). To navigate through the tuning menu press
up, down, left and right direction at the FunkySwitchTM of the Fanatec Steering
Wheel or turn the FunkySwitchTM clockwise / counter clockwise. Note: At the
ClubSport Universal Hub you can also use the D-Pad buttons on top of the
Universal Hub so you do not need to attach the separate FunkySwitch
TM
.
6.3.1 S_1 … S_5 (Setups)
Setups range: S_1 ... S_5 Setups default: S_1
The CSL Elite Wheel Base provides ve dierent setups to store your adjusted values independent from each other. To change the used and active setup
press up or down direction at the FunkySwitch
TM
of the Fanatec Steering Wheel
or turn the FunkySwitchTM clockwise / counter clockwise.
6.3.2 SEN (Sensitivity)
SEN range: 009 … 108 Aut SEN default: Aut
The sensitivity denes the steering angle. If SEN is set to 009 the steering
wheel can only be turned 90° (45° to left and 45° to right side direction from calibrated center position). If SEN is set to 108 the steering wheel can be turned
the me- chanical maximum way of 1080° (540° to left and 540° to right side direction from calibrated center position). If SEN is set to OFF/Aut the sensitivity
is controlled by the PC driver (see chapter PC driver for more details) or even
some games support this feature (e.g. Codemasters F1). To change the used
and active value press up or down direction at the FunkySwitchTM of the Fanatec Steering Wheel or turn the FunkySwitchTM clockwise / counter clockwise.
Aut means that our driver and games can change this setting automatically by
remote.
6.3.3 FF (Force Feedback)
FF range: OFF 001 … 100 FF default: 100
The Force Feedback denes the maximum strength of the motor when force
feedback eects from software / games are sent to the CSL Elite Wheel Base.
If FF is set to OFF, there will be no force feedback eect executed by the CSL
Elite Wheel Base motor. If FF is set to 001, the motor will execute only 1% of
the maximum motor power. If FF is set to 100, the motor will execute 100% of
the maximum motor power. To change the used and active value press up or
down direction at the FunkySwitchTM of the Fanatec Steering Wheel or turn the
FunkySwitchTM clockwise / counter clockwise.
30
6.3.4 SHO (Shock)
SHO range: OFF 010 ... 100 SHO default: 100
The strength of the shock / vibration motors inside the FANATEC Steering
Wheel can be adjusted from 100% to 0%. These vibration motors can be used
by a game directly (Fanatec SDK) or by the ABS function.
6.3.5 ABS
ABS range: 000 … 100 OFF ABS default: OFF
This feature can give you a direct and feel-able feedback about your brake
inputs. If you set the value to 100 the vibration will start as soon as you give
100% brake input to the game. If you set it to 95% the vibration will start if you
push the brake to 95% or more. The ABS feature uses the vibration within your
wheel rim (can be turned o by settin SHO to “0”) AND the vibration motor on
a CSP (V2) pedal set if it is connected directly to the wheel - not individually
by USB. ABS can also be simulated dynamically by the game if the developer
makes use of the Fanatec SDK. To change the used and active value press up
or down direction at the FunkySwitchTM of the Fanatec Steering Wheel or turn
the FunkySwitchTM clockwise / counter clockwise.
6.3.6 DRI (Drift mode)
DRI range: OFF 000 … 005 DRI default: OFF
The drift mode reduces the overall resistance of the wheel and let you turn the
wheel more easily. It almost works like a power steering. It reduces the basic
dampening of the wheel and makes the wheel turn faster. If the values is set
too high (or if the games FFB interferes with this feature) you might experience
some oscillation. If that happens - reduce the value or turn DRI “OFF” again.
To change the used and active value press up or down direction at the Funky-
SwitchTM of the Fanatec Steering Wheel or turn the FunkySwitchTM clockwise /
counter clockwise.
6.3.7 FOR (force), SPR (spring), DPR (damper)
FOR range: OFF 010 … 120 FOR default: 100 (%)
SPR range: OFF
010 … 120 SPR default: 100 (%)
DPR range: OFF
010 … 120 DPR default: 100 (%)
These force feedback modiers give you the ability to change the force feedback signals of a game (only applicable if game uses these eects). In theory
there are three types of signals which a game can send: Force (pushes the
31
wheel into a special direction), spring (pulls the wheel towards the center) and
damper (creates friction). Not every game uses all types of eects and some
games even use only one type to create all dierent feelings. Using your tuning
menu in the CSW you can increase or reduce these dierent eects individ-
ually. To change the used and active value press up or down direction at the
FunkySwitchTM of the Fanatec Steering Wheel or turn the FunkySwitchTM clock-
wise / counter clockwise.
Note: If SPR is set to low values or ‘OFF’ the CSL Elite Wheel Base will not be
able to move the attached Steering Wheel to correct center position after calibration run. Force, spring and damper modiers cannot be used on Xbox
One since those separated FFB signals are not used in the XBO force
feedback system.
IMPORTANT: Please do only set these values higher than 100% if the
force feedback eects are clearly not strong enough and weaker in comparison to other games. When the game sends full eects and the wheel
is set to 100% then the device will work on its power limit. Pushing up one
value to a very high number or even raising multiple values will result in
higher load on the motor and increased heat development.
For further information check the FAQ section on our website
www.fanatec.com/support.
6.3.8 FEI (Force Eect Intensity)
FEI range: OFF … 100 FEI default: 050
This parameter adjusts the intensity of force eects and can make eects more
smooth: OFF is very smooth and low noise while 100 is very sharp and direct.
Tuning this parameter can improve the feeling of the wheel depending on the
game. This can be helpful to reduce the noise level especially for bases assembled to tables or rigs.
32
6.3.9 BRF (brake force)
BRF range: OFF 010 … 100 BRF default: 050
This brake force modiers give you the ability to adjust the brake feeling according to your favour: Increasing the BRF to 100 means the user needs to
press the brake with minimum force to achieve 100% brake signal. Reducing
the BRF to OFF means the user needs to press the brake only with maximum
force to achieve 100% brake signal.
You can either check the brake signal level on the PC driver or you can see
it on the RevLEDs of the CSL Elite Wheel Base and/or the attached Steering
Wheel (depending on Steering Wheel type). To change the used and active
value press up or down direction at the FunkySwitch
TM
of the Fanatec Steering
Wheel or turn the FunkySwitchTM clockwise / counter clockwise.
NOTE: The parameter BRF availability is depending on the pedals
type at the Wheel Base’s PEDAL port, pedals have to support this feature.
Please read the description and/or manuals of your pedals to verify the
BRF feature is supported. For example the CSL Elite Pedals LC (= CSL
Elite Pedals with Loadcell Kit) and the ClubSport Pedals V3 support this
feature.
6.4 Revolution Lights (RevLEDs)
The CSL Elite Wheel Base introduces the RevLEDs feature integrated directly into the Wheel
Base. This RevLEDs are usually mirrored with
the RevLEDs of the Steering Wheel so games supporting the Steering Wheel
RevLEDs also by default support the Wheel Base RevLEDs.
Further, if games make use of it, the RevLEDs of the Wheel Base can indicate
a dierent meaning than the Steering Wheel RevLEDs. Example: Wheel Base
RevLEDs show the fuel level while the Steering Wheel RevLEDs indicate the
revolutions of the virtual car’s engine and push the driver to shift up at the best
moment.
Beyond this in-game feature, the RevLEDs also are a helpful indicator in case
of any unexpected behaviour: While the CSL Elite Wheel Base calibration run
after power ON is proceeding, the RevLEDs of the Wheel Base show the current status. For example, if no Steering Wheel is attached or is attached but
cannot be detected and identied, the three blue RevLEDs will not be lit.
After calibration run is completed the RevLEDs turn o automatically and the
game or software takes control.
33
6.5 Cooling system
To avoid damages to the CSL Elite Wheel Base
there is a well-managed cooling system integrated
to the hardware and the rmware.
6.5.1 Hardware measures
The CSL Elite Wheel Base has a fan inside which carries out the hot air from
the inside of the CSL Elite Wheel Base:
Make sure that there is nothing blocking the air intake at the CSL Elite Wheel
Base back side.
6.5.2 Automatic fans adjustment
The rmware provides dierent stages of fan control which are clearly dened
after intensive testing on the R&D lab.
When switching ON the CSL Elite Wheel Base the fan operates at maximum
speed until calibration run is completed.
The operation speed of the fan is adjusted according to the currently detected
temperature of the motor inside the CSL Elite Wheel Base and could even stop,
depending on used rmware version.
The temperature control is subject to change by rmware updates so that the
fans behaviour also could be changed.
34
ELECTRICAL OPERATION
7.1 Hotkeys
7.1.1 Tuning menu
To enter the tuning menu use tuning
menu button (usually the small black button close to the LED display of the used
Fanatec Steering Wheel; see corresponding quick guide of your Fanatec Steering
Wheel). The picture just shows the tuning
menu button on top of the ClubSport Universal Hub as an example:
7.1.2 Wheel center calibration
If a center calibration is needed (e.g. after updating the rmware of the CSL
Elite Wheel Base) rst you need to enter the tuning menu as described above.
When you use a regular Fanatec Steering Wheel like the BMW M3 GT2, the
Formula Black or Formula Carbon or the Porsche 918
RSR you must press the left and right stick at the same
time. Please see corresponding quick guide of the Fanatec Steering Wheel you use at the CSL Elite Wheel
Base.
The picture on the right hand side just shows the Fanatec Steering Wheel Porsche 918 RSR as an example:
When you use the ClubSport Universal Hub you have
to press
on top side of the Universal Hub at the same time to calibrate
the wheel center. On Fanatec Steering Wheels designed for Xbox One the cor-
responding buttons are.
+
Refer to the Quick Guides of your used
Steering Wheel.
ATTENTION: When initialization and auto calibration of the CSL Elite
Wheel Base is in progress never touch the attached steering wheel in
order to avoid injuries or incorrect calibration!
7
35
7.1.3 Switching modes
Initially the CSL Elite Wheel Base is in PC mode if no Fanatec Steering Wheel
for Xbox One is attached. For use on Xbox One the CSL Elite Wheel Base has
to be attached with a Fanatec Steering Wheel for Xbox One (e.g. Universal
Hub for Xbox One, CSL Steering Wheel P1 for Xbox One) and switch to Xbox
One mode.
When the wheel base is booted with attached Fanatec Steering Wheel for
Xbox One the wheel base is initially already in Xbox One mode, indicated by
the green LED above the “
”
button, see photo on the right
hand side:
In case the CSL Elite Wheel Base is in PC mode with at-
tached Fanatec Streering Wheel for Xbox One you have to
connect the wheel base to the Xbox One console via USB
cable and then press the buttons
+ or use the ‘MODE’ button instead at
the same time after auto calibration of the CSL Elite Wheel Base is completed.
Bith ways allow to toggle between PC and Xbox One mode when a Fanatec
Steering Wheel for Xbox One is attached, with other Fanatec Steering Wheels
the CSL Elite Wheel Base works on PC only.
PC Mode is idnicated by red lit LED above the “
”
button
Please see corresponding quick guide of the Fanatec Steering Wheel you use at the CSL Elite Wheel Base. Please see
user manual of the Universal Hub for Xbox One as well.
36
7.1.5 Shifter calibration mode
To enter the H-pattern shifter calibration mode on
regular Fanatec Steering Wheels press START
(10) + tuning menu button at the same
time. The START button is usually the black
button on the lower right center of the Steering
Wheel, the picture on the right hand side shows
the Porsche 918 RSR as an example:
To enter the H-pattern shifter calibration mode on
the Universal Hub press START (10) +
tuning menu button at the same time:
Put the H-pattern shifter’s lever into the
position shown on the LED display and
acknowledge each single position by
pressing START (10) to get to the next
one.
On Fanatec Steering Wheels designed for Xbox One the corresponding but-
tons are Tuning menu + MENU button
+
Please refer to the Quick Guides of your Fanatec Steering Wheel for more
detailed information.
NOTE: After rmware update the CSL Elite Wheel Base will request
the shifter calibration automatically as soon as a non-calibrated H-pattern
shifter is connected and detected. The menu will guide you through the
calibration steps as described next below.
Put the H-pattern shifter’s lever into the position shown on the LED display and
37
acknowledge each single position by pressing START (10) / MENU to get
to the next one.
The following pictures show the instructions on the LED display of the Universal
Hub but are similar on the other Fanatec Steering Wheels:
................neutral position
.......................... rear
....................... 1st gear
.......................2nd gear
....................... 3rd gear
....................... 4th gear
....................... 5th gear
....................... 6th gear
....................... 7th gear
If your shifter has no 7th gear just acknowledge it by pressing START (10)
when the shifter lever is physically in position of 6th gear. After all gears are
calibrated the LED display shows S_1 and the shifter is ready for use.
NOTE: If you did not intend entering the shifter calibration mode
please simply complete the calibration process without connected shifter and moving shifter lever, then leave the shifter calibration mode at the
end of the process. This has no impact on the CSL Elite Wheel Base original calibration itself and you can go ahead without shifter.
38
TROUBLESHOOTING
9
The CSL Elite Wheel Base must not be modied dierently than described
in this manual. Endor® AG expressly prohibits analysis and utilization of the
electronics, hardware, software and rmware contained in the controller. In
case diculties occur in connection with utilization of the CSL Elite Wheel
Base, please use the following guide for elimination of errors. On the website
www.fanatec.com/support you will nd further details and contact data.
If the CSL Elite Wheel Base is not working properly:
Problem description Solution
After rmware update of the CSL Elite Wheel
Base the steering wheel is not properly centered.
After doing a rmware update on the CSL Elite
Wheel Base the wheel center position must be
manually calibrated. See chapter ‘CSL Elite
Wheel Base Functions’ ‘Firmware and driver
update’ of this manual for more details.
After rmware update of the CSL Elite Wheel
Base the H-pattern shifter is not working properly.
After doing a rmware update on the CSL Elite
Wheel Base the H-pattern shifter must be manually calibrated. See chapter ‘CSL Elite Wheel
Base Functions’
‘Firmware and driver update’
of this manual for more details.
The driver window does not show the attached
Steering Wheel.
Make sure that you have updated your CSL Elite
Wheel Base to the latest rmware version which
can be downloaded from
www.fanatec.com/ support.
Check the pins inside the quick release of the
Steering Wheel, these must not be bent or
damaged.
Try to use another Steering Wheel. If this is also
not detected the CSL Elite Wheel Base might be
damaged.
Clean only with a dry or slightly damp cloth. Using cleaning solutions may damage your CSL Elite Wheel Base.
CLEANING
8
39
Problem description Solution
The tuning display does not show anything or is
not working partially.
Try to use another Steering Wheel. If this is also
not working properly the CSL Elite Wheel Base
might be damaged.
Check the pins inside the quick release of the
Steering Wheel, these must not be bent or
damaged.
Center calibration with Universal Hub is not working because of missing d-pad / sticks.
For the CSL Steering Wheel P1 for Xbox One, for
Universal Hub and for Universal Hub for Xbox
One there is a dierent button combination than
for other Fanatec Steering Wheels. See descrip-
tion in chapter ‘Hot- keys’ of this user manual as
well as the user manual for the Universal Hub.
After switching on the CSL Elite Wheel Base the
auto calibration is not working properly.
Make sure that you have updated your CSL Elite
Wheel Base to the latest rmware version which
can be downloaded from www.fanatec.com/support.
After playing a while the CSL Elite Wheel Base
seems to become weaker or is fading.
When the motor temperature is close to upper
limit the tuning menu values will be overwritten to
regular maximum values (not higher than 100 %).
Additionally the motor power level is controlled by
rmware so that the FFB strength may fade in this
high temperature range but the motor will not be
damaged. This allows extending the duration of
driving before the motor has to completely stop
operating to calm down.
Let your CSL Elite Wheel Base calm down before continue using it.
After playing a while the CSL Elite Wheel Base
motor has switched OFF.
When the temperature is exceeding the upper limit the motor will be deactivated for a while until the
temperature is low enough (to protect the hardware from damages).
Let your CSL Elite Wheel Base calm down before continue using it. Contact our customer support if this happens consecutively.
Fans are always working in full speed even if
ClubSport Wheel Base just was switched ON and
cannot have higher temperatures.
In case of malfunctioning temperature sensor the
fans are working at maximum speed to protect the
hardware from overheat. Please contact our customer support.
After calibration run at startup of CSL Elite Wheel
Base the attached steering wheel doesn’t go to
correct center position.
Please check your tuning menu settings, the value
for SPR (spring) must be higher than ‘000’ as this
eect is required to make correct centering. Default value is ‘100’.
Some of the tuning menu settings are not availa-
ble on Xbox One and cannot adjust.
As the Xbox One uses a dierent FFB eect system the parameters SPR, FOR and DPR cannot
be adjusted separately within this system. The
only option is the adjustment of the overall FFB
strength by parameter FF.
40
TRADEMARKS
SERIAL NUMBER
11
10
“Xbox®” and “Xbox OneTM” is a trademark of Microsoft Corporation. All rights
reserved.
“FANATEC
®
” and “Endor®” are registered trademarks of Endor® AG/Germany.
All rights reserved.
Before contacting the Fanatec Customer Support please note the serial number of your CSL Elite Wheel Base: ………………………………………………...
You can nd the serial number on a sticker on the bottom side of you CSL Elite
Wheel Base or on stickers on one of the packaging boxes. The serial number
starts with letters ‘LE’ and has additional 8 numbers, for example: LE62407001.
41
ECOLOGY ADVICE
12
In the European Union: At the end of its working life, this product
should not be disposed of with standard household waste, but
rather dropped o at a collection point for the disposal of Waste
Electrical and Electronic Equipment (WEEE) for recycling.
Depending on their characteristics, the materials may be recycled. Through recycling and other forms of processing Waste
Electrical and Electronic Equipment, you can make a signicant
contribution towards helping to protect the environment.
Please contact your local authorities for information on the collection point
nearest you.
For all other countries: Please adhere to local recycling laws for electrical and
electronic equipment.
Retain this information. Colours and decorations may vary.
In the European Union: The packaging materials can be depolluted for recycling according to the legal regulations depending on
the country responsible for the corresponding law.
For all other countries: Please adhere to local recycling laws for
packaging materials.
42
FCC COMPLIANCE
CE COMPLIANCE
13
14
This device complies with part 15 of the FCC rules. The operation
of this device is subject to the following two conditions:
• This device may not cause harmful interference, and must
accept any interference received, including interference that
may cause undesired operation.
•
This device was not modied dierent than described explicitly in this
user manual.
Note: This device was tested and approved to the limitations for class B of
digital devices according to part 15 of the FCC rules. This limitations should ensure an adequate protection against harming interferences in residental areas.
However, a warranty for not-occuring of interferences is not assumed.
Do not modify the device dierent than described explicitly in this user manual.
Nevertheless, if you do modications dierent from the described in this manual
you can be determined to stop the operation of the device.
This device complies with the European product regulations according to CE regulations.
The CE regulations contain basic requirements for safe usage of
technical products.
43
WARRANTY
15
Please check the FAQ database at www.fanatec.com/support to see if your
problem can be solved there. Normally, the warranty period is one year. How-
ever, this may dier depending on the respective state.
1) Endor
®
AG grants for the hardware product – as extension of shorter national warranty regulations, if applicable a one- year warranty for material and
manufacturing defects. The warranty does not include defects that are due to
commercial use of the product and/or normal wear and tear and/or damaging
by third parties and/or improper utilization or treatment and/or utilization of the
product contrary + to the operating and maintenance instructions and/or not intended installation and/or non-compliance with the local safety standards and/
or the results of an intervention by a third party or a not authorized opening of
the device including any measures for modication, adjustment and/or adaptation measures (also in case of professional execution). Warranty applies as
of the date of purchase when the nal customer purchased the product, and is
exclusively limited to the rights as of 2), as far as this does not limit any further
legal warranty claims on the basis of various national laws. Warranty is subject
to return of the defective product with carriage paid, within the warranty period,
including the original receipt that must include date of purchase as well as the
company stamp/company print of the rst dealer.
2) The warranty covers – at the choice of Endor
®
AG – either gratis repair or replacement of the device or components of the device. With defects that are not
covered by the warranty and/or that are excluded from warranty (see above),
possibilities for repair are to be requested with the local customer service or the
local dealer. As far as permitted by law, any further liability - with the exception
of intent and gross negligence – is excluded for any indirect or direct damages
and consequential damages, regardless of whatsoever basis of claim.
This applies in particular to damages with other property, damages to persons,
data losses as well as nancial losses like loss of prot as well as transport
damages in connection with returns to Endor
®
AG. As far as liability limitations
are not legally allowed or eective in certain states or certain regions, the limitations are to be eective to such extent that exclusions of liability. This gaming
device is designed to withstand approximately one hour of use per day during
the course of the warranty period of one year.
Fanatec® is a registered trademark of Endor AG
Designed and developed by Endor AG in Germany
Loading...