www.fanatec.com
ATTACHING THE RIM DETACHING THE RIM
Please download and install the latest PC driver and
wheel base rmware before mounting the CSL Elite
Steering Wheel P1 for Xbox One. You can obtain it at
Fanatec’s website (www.fanatec.com) in the download
section.
Align wheel base axle to correct position.
Slide steering wheel onto wheel base axle.
Slide steering wheel off wheel base axle.
Turn out the xing screw and open
clamp ring mechanism, use only the
Allen key which comes with the steering
wheel!
Use xation screw (M6 x 18mm at head) and
Allen key from box contents.
Store xation screw and Allen key safely for
later use.
Push steering wheel until the screw hole
matches with hole on wheel base axle.
Turn the steering wheel top side down to see the bottom
side of the clamp ring to follow next step below.
Turn in xation screw to x the clamp ring
mechanism.
Use only the Allen key from box contents.
IMPORTANT: Tighten only by using the short
lever of Allen key!
QuickGuide
EN
1
1
2
3
2
3
4
5
6
EXCHANGEABLE BUTTON CAPS
To detach the button caps, simply pull them out by hand.
They can be replaced with the included set of racing style
button caps for CSL Elite Steering Wheel P1.
Fanatec® is a registered trademark of Endor AG
Designed and developed by Endor AG in Germany
Manufactured by
Seligenthaler Straße 16 a - 84034 Landshut - Germany
Telephone: +49 (871) 9221-122 Fax: +49 (871) 9221-221
Email: info.webshop@fanatec.com
Internet: www.fanatec.com - www.endor.ag
1
3
2
TUNING OPTIONS
To enter tuning menu press button . To navigate inside
the menu, use the D-pad stick:
- Press D-pad up or down to access 5 setups
- Press D-pad right or left to go through the options
and press or hold it up or down to change option values
SHIFTER CALIBRATION
To enter shifter calibration mode, simultaneously press the
two buttons
+
, highlighted below.
For the detailed process read shifter manual.
CENTER CALIBRATION
If a center calibration is needed (e. g. after rmware update of
wheel base) you need to enter the tuning menu by pressing
button
as shown on the graphic
“S_...” will appear on
the display. Now turn the wheel to its center position and
then press two buttons
+
at the same time to calibrate
the wheel center.
To switch between modes simultaneously press and hold the
two buttons
+ , highlighted below, for one second.
The wheel base LED indicates the active mode:
- Green means Xbox One mode
- Red means PC mode
- Blue means PS4
TM
mode*
- Purple means CSW V2
compatibility mode*
2
25
2 6
3
4
56
9
12
8
10
11
7
1
S_...
1
Press tuning button
2
Turn the wheel to the center
position
3
Press the two buttons +
at the same time
* not applicable for every Fanatec wheel
base, please check the individual user
manuals of your Fanatec wheel base.
MODES
BUTTON MAPPING
Button Button no. PC Xbox One
LT 8 LT 100% (brake)
RT 7 RT 100% (accelerator)
LSB 12 LSB -> LB (shift down)
RSB 11 RSB -> RB (shift up)
10 MENU
9 VIEW
A 2 A
B 3 B
X 1 X
Y 4 Y
Shifter Paddle L
6 LB
Shifter Paddle R
5 RB
D-pad press 26 Horn
D-pad left D-pad left D-pad left
D-pad right D-pad right D-pad right
D-pad up D-pad up D-pad up
D-pad down D-pad down D-pad down
25 Guide
Loading...