Model Description
MP-1311
Main System
Processor
Intel Atom® x5-Z8350 Quad Core 1.44GHz, up to 1.92GHz
Display
10.1-inch IPS, 1280 x 800, 300nits
Touch Panel
True-Flat Projected-Capacitive Multi Touch (PCAP)
Memory
4GB DDR3L 1600MHz
Storage
64GB eMMC
Micro-SD Slot
Up to 128GB
Communication
Wi-Fi IEEE 802.11 b/g/n, Bluetooth and GPS
Webcam
2M Front Camera (FF) and 5M Rear Camera (AF)
Speaker
2 x 0.8W Speakers
Sensor
Light Sensor, G Sensor and Gyroscope
I/O Interface
USB
1 x USB 3.0 Type A
Po-go Pin
1 x Pogo Pin (for charging and data transmission)
Peripherals
External Modules
MSR
2D Barcode Scanner
Finger Print
Power Management
Internal Battery
Lithium Polymer Battery 4800mAh
Power Adapter
5V@3A 15W AC Power Adapter (option)
Mechanical & Environmental
Dimension
Main Tablet : 310 (W) x 187.2 (H) x 25.9 (D) mm
Dock Station : 220.5 (W) x 160.8 (H) x 125.8 (D) mm
Weight
Main Tablet : 0.95kg (w/o accessories)
Dock Station : 1.23kg (w/o power adapter)
Operation System
Windows 10 IoT Ent LTSB Entry EPKEA
Certification
CE / FCC Class B
Operation Condition
0°C to +40°C / 10 to 85% without condensation
Charging Condition
0°C to +40°C / 10 to 85% without condensation
Storage Condition
-10°C to +50°C / 10 to 85% without condensation
Specifications MP-1311
10.1 Inch Mobile Point of System
Quick Installation Guide
IMPORTANT SAFETY INFORMATION
Read following instructions carefully.
Use only parts, especially power adapter, recommended by the manufacturer;
unapproved parts may be hazardous.
Make sure that the voltage applied to the power outlet is within the specified
range (100VAC ~240VAC). Improper power source voltage range will cause
damage.
Power off the system and remove the power adapter while cleaning the system.
Before powering on the system, make sure all the
peripherals are firmly installed.
MP-1311 is required to be charged over 8 hours
when used for the first time.
Ver. 1.0
© Copyright Fametech Inc. (TYSSO), 2019
Parts Descriptions
A. Main Tablet
5VDC
Input
2D Barcode
Scanner
Scan Trigger
External
Module Sku*
Volume
Up / Down
Light Sensor LED Indicator
Front Camera
Alignment
Mark
(to Dock Station or Charging Cradle)
Pogo Pin
Rear Camera Press 3 Sec
Hand Strap
Power
Button
MSR
Finger Print
MPOS Installation
1. Charge Your Tablet
A. Power Adapter via Main Tablet B. Main Tablet via Charging Cradle
5VDC
Input
12VDC
Input
AC Power Adapter
2. Start Your POS System
Power Button
BEEP!
Dock Station
or
Charging Cradle
To Start the System:
To Shut Down the System:
AC Power Adapter
Forced Shut Down:
10 Sec
MP-1311 is required to be charged over 8 hours
when used for the first time.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipmnet generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is lik ely to cause harmful
required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
Loading...