Falcon SVR2K-2T, OM48021-1, SVR2K-1T, SVR3K-1, SVR3K-2T User Manual

FALCON ELECTRIC INC.

SVR SERIES

PRECISION UTILITY VOLTAGE

REGULATOR AND CONDITIONER

OWNER’S MANUAL

SVR1K-1T & SVR2K-2T
SVR2K-1T &SVR2K-2T

SVR3K-1 & SVR3K-2T

FALCON Electric Inc., 5106 Azusa Canyon Rd., Irwindale, California 91706 800-842-6940 Fax: [phone] Email: [e-mail]

2005 Falcon
All other brand names and trademarks are the property of their respective owners.
The information and specifications stated in this document are subject to change without notice. 2005-03-21
 Falcon, Falcon Electric and UPS Plus logos are registered trademarks of Falcon Electric , Inc.

OM48021-1 Rev. C



Electric Inc. All rights reserved.

1

SVR SERIES FEATURES

• COMPACT SIZE, LIGHT WEIGHT

• WIDE INPUT VOLTAGE WINDOW

• TIGHT OUTPUT VOLTAGE REGULATION (±2%)

• INPUT POWER FACTOR CORRECTION

• SURGE PROTECTION

• HIGH EFFICIENCY

• OVER CREST RATIO LED INDICATOR

• RS-232 INTERFACE

OM48021-1 Rev. C

SYSTEM BLOCK DIAGRAM

2

This following User’s Manual is provided to better enhance your understanding of the product and ensure its proper
installation and usage. Reading this manual carefully prior to installation of the SVR Series Precision Utility Voltage
Regulator and Conditioner will save time and ensure worry-free operation.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important safety instructions that must be followed during the installation, operation and
maintenance of this equipment. Please store this manual in a safe place for future reference.

STORAGE & INSTALLATION

CAUTION: All of the SVR models presented herein are designed for installation and use in a controlled
enviroment free of dust, dirt and water.

The SVR Series Precision Utility Voltage Regulator and Conditioner is designed for installation in a controlled
environment (temperature controlled, indoor area free of conductive contaniments).

The system is lightweight and can be easily moved. Some important points to consider when positioning a unit for
operation:

 It is preferable that a dedicated outlet is accessible to connect the SVR. DO NOT modify the supplied cord in any way

nor should an extension cord of any kind be used.

 The cord paths in the system installation should remain clear of foot traffic or anything else that may disturb

permanent connection.

 The installation site should maintain an ambient air temperature of less than 104

the system remains cooler during operation, there is less stress on internal electronics. An air conditioned
environment will yield the longest SVR life.

 The SVR air inlets, vents and fan should not be obstructed or blocked in any way. The more breathing space the

system has, the cooler it operates.

 The air should remain free from excessive dust and chemical fumes.

Once a location has been selected and the unit is installed, it is ready for operation.

o

F (40oC). When the environment for

This Symbol Denotes Earth Ground

OM48021-1 Rev. C

This Symbol Denotes On and Off

3

CARE & MAINTENANCE

The SVR Series Precision Utility Voltage Regulator and Conditioner is designed to be maintenance-free. It can be
cleaned with a damp cloth or nonabrasive cleanser providing it is turned off and the input plug is disconnected from the
utility source. Be sure vents and fans are kept free from accumulation of dust, dirt or lint.

FALCON ELECTRIC SVR SERIES

INSTALLATION AND STARTUP CHECK LIST

1. Verify the following is included in the SVR shipping carton:
 SVR
 Power Cord  Owner’s Manual

2. Verify that the SVR unit is configured for the proper input/output voltage and frequency. This information is stated
on the nameplate label located on the rear panel of the unit as well as setting dip switch settings also located on
the SVR rear panel.

3. For the 1kVA model, connect the power cord to the inlet located on the SVR rear panel.

4. Select a suitable location for the SVR near enough to the computer or equipment to connect the power cord.

Verify the location you have selected has adequate ventilation to allow for the proper cooling of the SVR. DO

NOT
BLOCK SVR FANS OR AIR VENTS. THE SVR MUST NOT BE INSTALLED IN AN ENCLOSED AREA.

5. Turn the input switch located on the SVR rear panel to the “on” position. The internal SVR fan will turn on and

after several seconds the front panel “line” indicator should turn on, followed by the “inverter” indicator.

6. Turn on the connected equipment and verify the SVR does not go into overload, by using the front panel load

indicator.

TO TURN OFF THE SVR

, TURN OFF THE INPUT CIRCUIT BREAKER. THE SVR WILL RUN FOR ABOUT 30

SECONDS AND SHUTDOWN.

IMPORTANT

OM48021-1 Rev. C

4