Falcon RM70, RM170A, RM170, RM70A Installation Instructions Manual
RM70, RM70A, RM170, and RM170A
Removable Mullions
PAGE NO. REVISION
1 of 2
F
4270108237
Installation Instructions
1. Prepare frame header for filler or adapter plate.
Install filler or adapter plate and top bracket.
For RM70 and RM170, see Figures 1 and 2.
(Filler, filler mounting screws, and bracket
mounting screws by others.)
For RM70A and RM170A, see Figures 3 and 4.
2. Prepare floor and threshold for bottom bracket.
Install bottom bracket (Figures 5 and 6, other
side).
3. Cut mullion to length from top (Figures 7 and 8,
other side).
4. Slide mullion over top fitting and swing into
position on bottom fitting (Figure 9, other side).
5. Slide mullion clamp over top fitting and secure
with three screws (Figure 10, other side).
6. Install security clips on door (Figure 11, other
side).
Figure 2. Filler and top bracket installation (RM70
and RM170).
Filler (by others) flush
with stop, centered on
center line of doors
doors
10-32 x 1/2" FPHMS
(by others)
Figure 4. Adapter plate and top bracket
installation (RM70A and RM170A).
Install top bracket to
adapter plate with three
10-32 x 1/2" FPHMS
#10 x 1" FPHMS
4 places
9/16"
1-11/16"
2-3/4"
1-5/8"
doors
Door
Door
Door
Figure 1. Header and filler preparation for top
bracket (RM70 and RM170).
Filler (by
others)
Drill and tap header and filler
for 10-32 screws, 3 places
Top bracket
location
Figure 3. Header preparation for adapter plate
(RM70A and RM 170A).
View
looking up
Adapter plate
11/32"
1-27/32"
1-1/8"
2-1/4"
1-1/2"
doors
Prepare header for #10 x 1"
FPHSMS, 4 places
Adapter
plate location
Adapter plate
Door
Door
Door
View looking up
Customer Service
1-877-671-7011 www.allegion.com/us
© Allegion 2016
Printed in U.S.A.
4270108237 Rev. 12/16-f
RM70, RM70A, RM170, and RM170A
Removable Mullions
PAGE NO. REVISION
2 of 2
F
Figure 6. Bottom bracket installation.
#14 x 1" screw anchors
in floor, 3 places
#10 x 1" FPHSMS
3 places
Figure 5. Floor and threshold preparation
for bottom bracket.
Figure 7. Required mullion length.
3/4"
1/4"
Cut mullion
1/16" less
than this
dimension
Top
bracket
Bottom
bracket
Figure 9. Install mullion.
Figure 11. Position door stabilizer clips as shown, drill and
tap door 10-32, 4 places, and install door stabilizer clips.
10-32 x 1/2" FPHMS
4 places
1/32"
min.
1/32"
min.
Frame stabilizer clips
on mullion (mullion
not shown for clarity)
Door stabilizer clips
4270108237
Figure 10. Slide mullion clamp up over
top bracket and secure with screws.
10-32 x 3/8"
slotted truss head MS
3 places
Figure 8. Cut mullion to length.
Clamp
Header not
shown for
clarity
7/8"
1-11/16"
2-3/4"
1"
1-5/8"
Prepare floor for #14 x 1"
screw anchors, 3 places
doors
Door
Door
Door
Cut out threshold
for bottom bracket
View
looking
down
1 Slide mullion
over top
bracket
2 Swing mullion
into position on
bottom bracket
11"
66"
Cut top end
CAUTION: There is
a steel tube inside
of the mullion
4-3/4"
approx
of latchbolt
Customer Service
1-877-671-7011 www.allegion.com/us
© Allegion 2016
Printed in U.S.A.
4270108237 Rev. 12/16-f
Loading...