Falcon Professional+ FX 90 Induction G5 User's Manual & Installation Instructions
Professional+ FX 90 Induction G5
USER GUIDE &
INSTALLATION INSTRUCTIONS
METHOD
1. For the soufflŽ, press the raspberries through a fine
sieve to produce 180 g of purŽe. Put this into a heavybottomed pan, add the lemon juice and reduce down to
a thick jam, stirring from time to time and being careful
not to let it catch and burn.
2. Put 45 g of the sugar in a separate pan. Melt it and then
boil until it becomes a thick syrup (121 ¡C on a sugar
thermometer). To test without a thermometer, dip a
teaspoon into the syrup and then dip quickly into cold
water. You should be able to roll the cooling syrup into
a ball between your fingers. Be careful as the syrup is
extremely hot. When it has reached the right point, stir
the hot syrup into the raspberry jam.
3. Mix the framboise and cornflour together and stir into
the jam over the heat. Turn the jam into a small bowl,
sprinkle the surface with icing sugar and cover with cling
film.
4. Preheat the oven (not grill) to 180 ¡C shelf level 2
(conventional oven), 160 ¡C (fan oven) or gas mark 4
centre shelf.
5. Whisk the egg whites with the cream of tartar until you
can form soft peaks, then fold in the remaining caster
sugar. Lightly fold the whites into the jam, leaving thin
traces of white visible in the mixture.
6. Spoon into four large buttered and sugared ramekins,
place these on a baking tray and bake for 10 minutes.
7. Dust with icing sugar.
INGREDIENTS
¥ 400 g raspberries
¥ 1 tbsp lemon juice
¥ 100 g caster sugar
¥ 2 tsp cr�me de framboise
¥ 1 tsp cornflour
¥ 180 g egg whites (about 6)
¥ Pinch of cream of tartar or a squeeze of lemon juice
¥ Icing sugar for dusting
RASPBERRY SOUFFLă
SLOW BAKED LEG OF LAMB
METHOD
1. Preheat the oven to 220 ¡C (for a conventional oven), 200 ¡C
(for a fan oven) or gas mark 7.
2. Pull the small sprigs off the rosemary branches and set aside
with the garlic.
2. Using the tip of a paring knife, make up to 20 well-spaced
cuts into the flesh of the lamb, about 2.5 cm inch deep.
Divide the rosemary sprigs, garlic and anchovies and push
down into the cuts. Place the leg on a large roasting tin and
pour over the oil, massaging it all over the joint. Season well
with salt and pepper and pour the wine and 250 ml water
into the tin.
3. Put into the oven and sear for 15 minutes, then turn the
temperature right down to 130 ¡C (conventional oven),
110 ¡C (fan oven) or gas mark 1 and roast for 4Ð5 hours,
basting every 30 minutes or so. Basting frequently helps
to keep the meat moist and encourages the build up of a
good glaze on the outside. Add more liquid (wine or water)
if the tin looks dry Ð there should always be liquid in the tin
throughout this cooking process.
4. The meat is ready when it starts to fall off the bone, at which
point it should have a core temperature of 90 ¡C. Remove
from the oven, transfer to a warmed carving dish, cover
loosely with foil and leave to rest in a warm place for 30Ð45
minutes before carving.
5. Pour the juices from the tin into a tall hi-ball glass and allow
to settle. Spoon the fat from the top of the glass. There
should be enough sticky, reduced juices for an intense gravy
hit Ð if not, pour the juices you have back into the roasting
tin and put it over the heat, pour in a splash of water or wine
and deglaze the tin scraping up all the sticky bits from the
base. Boil fast until syrupy, taste and correct the seasoning.
INGREDIENTS
¥ 2Ð3 large sprigs of rosemary
¥ 4 large garlic cloves cut in half lengthways
¥ 1.8 kg leg of lamb
¥ 8 good quality anchovy fillets, halved
¥ 100 ml olive oil
¥ 250 ml dry red wine
¥ Maldon salt and freshly ground black pepper
i
Contents
1. Before You Start... 1
Installation and Maintenance 1
Peculiar Smells 1
Ventilation 1
Personal Safety 1
Hob Care 2
Cooker Care 2
2. Overview 3
The Hob 3
The Multi-function Oven 6
Energy Saving Panel 8
Operating the Oven 9
The Clock 9
Accessories 11
Oven Light 11
Storage 12
3. Cooking Tips 13
Cooking with a Multi-function Oven 13
Tips on Cooking with the Timer 13
General Oven Tips 13
4. Cooking Table 14
5. Cleaning Your Cooker 15
Hob 15
Oven and Divider 15
Control Panel and Oven Doors 16
Cleaning Table 16
6. Troubleshooting 17
7. Installation 19
Dear Installer 19
Safety Requirements and Regulations 19
Provision of Ventilation 19
Location of Cooker 19
Positioning the Cooker 20
Moving the Cooker 20
Levelling 21
Fitting the Stability Bracket or Chain 22
Electrical Connection 23
Repositioning the Cooker Following
Connection
23
Final Checks 24
Final Fitting 24
Customer Care 24
8. Circuit Diagram 25
Oven Circuit Diagram 25
Induction Hob Circuit Diagram 26
9. Technical Data 27
Professional+ FX SC 90 Induction U110128-03A
ii
1
1. Before You Start...
Thank you for buying a this cooker. It should give you many
years of trouble-free cooking if installed and operated
correctly. It is important that you read this section before you
start, particularly if you have not used an induction cooker
before.
CAUTION: This appliance is for cooking purposes
only. It must not be used for other purposes, for
example room heating. Using it for any other
purpose could invalidate any warranty or liability
claim. Besides invalidating claims this wastes fuel
and may overheat the control knobs.
This cooker is a Class 2 Subclass 1 appliance.
Installation and Maintenance
This cooker must be installed must be in accordance with
the relevant instructions in this booklet, with the relevant
national and local regulations, and with the local electricity
supply companies’ requirements.
Make sure that the cooker is wired in and switched on.
The hob control display will ash for about 2 seconds
during rst power setting – this is normal.
The cooker should be serviced only by a qualied service
engineer, and only approved spare parts should be used.
Always allow the cooker to cool and then switch it o at the
mains before cleaning or carrying out any maintenance work,
unless specied otherwise in this guide.
Peculiar Smells
When you rst use your cooker it may give o a slight odour.
This should stop after use.
Before using for the rst time, make sure that all packing
materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200°C and run for at
least an hour.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
Ventilation
The use of a cooking appliance results in the production
of heat and moisture in the room in which it is installed.
Therefore, make sure that the kitchen is well ventilated – keep
natural ventilation holes open or install a powered cooker
hood that vents outside. If you have several hotplates on, or
use the cooker for a long time, open a window or turn on an
extractor fan.
Personal Safety
Important information for pacemaker and implanted
insulin pump users: The functions of this hob comply with
the applicable European standards on electromagnetic
interference. If you are tted with a pacemaker or
implanted insulin pump and are concerned please consult
your doctor for medical advice.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in
a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
WARNING: The appliance and its accessible parts
become hot during use and will retain heat even
after you have stopped cooking. Care should be
taken to avoid touching heating elements. Children
less than 8 years of age shall be kept away unless
continuously supervised.
NEVER wear loose-tting or hanging clothes when
using the appliance.
CAUTION: A long term cooking process has to be
supervised from time to time. A short term cooking
process has to be supervised continuously.
Danger of re: DO NOT store items on the cooking
surfaces.
To avoid overheating, DO NOT install the cooker
behind a decorative door.
Children should be supervised to make sure that
they do not play with the appliance.
DO NOT use a steam cleaner to clean the cooker.
When the hob is in use keep magnetic items, such as
credit and debit cards, oppy disk, calculators, etc.
away.
Accessible parts will become hot during use and will
retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and
never wear loose-tting or hanging clothes while
the appliance is in use.
Always be certain that the controls are in the OFF
position when the oven is not in use, and before
attempting to clean the cooker.
Take care when touching the marked cooking areas
of the hob.
When the oven is on, DO NOT leave the oven door
open for longer than necessary, otherwise the
control knobs may become very hot.
Always keep combustible materials, e.g. curtains, and
ammable liquids a safe distance away from your cooker.
Use dry oven gloves when applicable – using damp
gloves might result in steam burns when you touch
a hot surface. Do not use a towel or other bulky cloth
in place of a glove – it might catch re if brought into
contact with a hot surface.
DocNo.015-0306 - Introduction - Induction - Single cavity
2
DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
DO NOT spray aerosols in the vicinity of the cooker
while it is on.
NEVER operate the cooker with wet hands.
DO NOT use aluminium foil to cover shelves, linings
or the oven roof.
NEVER heat unopened food containers. Pressure
build up may make the containers burst and cause
injury.
DO NOT use unstable saucepans. Always make sure
that you position the handles away from the edge of
the hotplate.
Make sure to use adequately sized pans with at
bottoms that are large enough to cover the surface
of the hotplate heating area. Using undersized
pans will expose a portion of the hotplate surface
to direct contact and may result in the ignition of
clothing.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on re. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
WARNING! Unattended cooking on a hob with fat or
oil can be dangerous and may result in re.
NEVER leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. NEVER try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
DO NOT use the top of the ue (the slots along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.
DO NOT use water on grease res and never pick
up a aming pan. Turn o the controls and then
smother a aming pan on a surface unit by covering
the pan completely with a well-tting lid or baking
tray. If available, use a multipurpose dry chemical or
foam-type re extinguisher.
This appliance is heavy so take care when moving it.
Hob Care
DO NOT use the hob surface as a cutting board.
DO NOT leave utensils, foodstus or combustible items on
the hob when it is not is use (e.g. tea towels, frying pans
containing oil).
DO NOT place plastic or aluminium foil, or plastic
containers, on the hob.
DO NOT leave the hob zones switched on unless
being used for cooking.
NEVER allow anyone to climb or stand on the hob.
DO NOT stand or rest heavy objects on the hob. Although the
ceramic surface is very strong, a sharp blow or sharp falling
object (e.g. a salt cellar) might cause the surface to crack or
break.
Should a crack appear in the surface, disconnect the
appliance immediately from the supply and arrange
for its repair.
Always LIFT pans o the hob. Sliding pans may cause marks
and scratches. Always turn the control to the OFF position
before removing a pan.
Objects such as pan lids and items with thin bases
including kettles, may stick to the ceramic surface.
In the unlikely event that this happens DO NOT
attempt to lift or lever the item to remove, as this
may cause damage to both the item and the ceramic
surface. Remove objects by carefully sliding to the
hob perimeter. Damage caused by incorrect removal
will not be covered under the terms of the warranty.
DO NOT place anything between the base of the pan and the
hob surface (e.g. asbestos mats, aluminium foil, wok stand).
Take care NOT to place metallic objects such as
knives, forks, spoons and lids on the hob surface
since they can get hot.
The appliance is not intended to be operated by
means of external timer or separated remote-control
system.
Care should be taken that no water seeps into the appliance.
Only certain types of stainless steel, enamelled steel pans or
cast iron pans with enamelled bases are suitable for induction
hob cooking.
The ceramic surface should be washed after use to prevent it
from becoming scratched or dirty. However, you should clean
the hob with caution as some cleaners can produce noxious
fumes if applied to a hot surface.
DO NOT use abrasive cleaners/pads, oven aerosols/pads
or stain removers on the surface.
We recommend that you avoid wiping any surface unit areas
until they have cooled and the indicator light has gone o.
Sugar spills are the exception to this (see ‘Cleaning your
Cooker’). After cleaning, use a dry cloth or paper towel to
remove any cleaning cream residue.
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth.
3
2. Overview
The induction cooker (Fig.2-1) has the following features:
A. 5 induction cooking zones
B. A control panel
C. A multi-function oven
D. A storage drawer
The Hob
Use only pans that are suitable for induction hobs. We
recommend stainless steel, enamelled steel pans or cast iron
pans with enamelled bases. Note that some stainless steel
pans are not suitable for use with an induction hob so please
check carefully before purchasing any cookware.
Pans made of copper, aluminium or ceramic are not suitable
for use on an induction hob. The kind of pan you use and the
quantity of food aects the setting required. Higher settings
are required for larger quantities of food.
Pots and pans should have thick, smooth, at bottoms
(Fig.2-2). This allows the maximum heat transfer from the
hob to the pan, making cooking quick and energy ecient.
Never use a round-bottomed wok, even with a stand.
Fig.2-2
ArtNo.273-0003 - 90IN - Prof+ annotated
Professional + FX
A
B
C
D
Fig.2-1
DocNo.023-0015 - Overview - 90 induction SC - Prof+ FX
4
ArtNo.051-0002 - Min pan diameter
Cooking Zone
Minimum Pan Diameter
(Pan Base) mm
Front left
Rear left
Centre
Rear right
Front right
140
180
180
180
140
Table 2-1
The very best pans have bases that are very slightly curved
up when cold (Fig.2-3). If you hold a ruler across the bottom
you will see a small gap in the middle. When they heat up the
metal expands and lies at on the cooking surface.
Make sure that the base of the pan is clean and dry to prevent
any residue burning onto the hob panel. This also helps
prevent scratches and deposits.
Always use pans that are the same size as (or slightly larger
than) the areas marked on the hob. Using a lid will help the
contents boil more quickly.
Take care when placing hot lids onto the hob
surface. Lids that have been covering boiling or
steaming foods can ‘stick’ to the ceramic glass.
Should this occur, DO NOT attempt to lift the lid
o the hotplate: this may damage the hob surface.
Instead, slide the lid to the edge of the hob surface
and remove.
Always take care before touching the surface, even
when the hob is turned o. It may be hotter than you
think!
The induction hob comprises of ve cooking zones
containing induction elements with dierent ratings and
diameters (Fig.2-4) each with a pan detector and residual
heat indicator, and a hob control display.
The hob control display (Fig.2-5) informs you of the following
induction hob functions:
Pan detector
H Residual heat indicator
A Automatic heat-up
Child lock
L1/L2 Low temperature setting
P Power boost setting
Pan Detector,
IMPORTANT: After use, switch o the hob element by its
control and DO NOT RELY on the pan detector.
If a cooking area is switched on and there is no pan in place
or if the pan is too small for the cooking area, then no heat
will be generated. The symbol [
] will appear on the hob
control display; this is the “pan-missing symbol”. Place a pan
of the correct size on the cooking area and the [
] symbol
will disappear and cooking can begin. After 10 minutes
without detecting a pan the cooking zone will switch o
automatically.
Table 2-1 shows the minimum pan sizes recommended for
each cooking zone.
Note: Using pans with a base diameter smaller than those
recommended will result in a power reduction.
Residual Heat Indicator, H
After use, a cooking zone will remain hot for a while as heat
dissipates. When a cooking zone is switched o the residual
heat indicator symbol [H ], will appear in the display. This
shows that the cooking zone temperature is above 60 °C and
Fig.2-5
Fig.2-3
Max: 1.85 kW
Boost: 2.5 kW
Max: 1.85 kW
Boost: 3.0 kW
Max: 1.85 kW
Boost: 2.5 kW
Max: 1.15 kW
Boost: 2.0 kW
Max: 1.15 kW
Boost: 2.0 kW
Fig.2-4
5
may still cause burns. Once the temperature has dropped to
below 60 °C the [H ] will go out.
Automatic Heat-up, A
This function is available on all of the cooking zones. It
allows rapid heating up of the element to bring the selected
cooking zone up to temperature. Once the zone is at the
required cooking temperature the power level will reduce
automatically to the preset level.
The function is selected by turning the control knob to the
‘A ’ position. This can be selected by turning the control knob
momentarily counter-clockwise from the zero position until
the symbol [A ] is shown on the hob control display.
Once the [A ] is displayed, turn the control knob to the level
of your choice (1 to 9). The pan will heat up at 100% power
for a specied time before the power is reduced to the level
selected.
When the Automatic Heat-up function is activated, the hob
control display will ash alternately between the [A ] setting
and the chosen power level.
Once the automatic heat-up time has ended the hob display
will stop ashing and will show the chosen power level.
The Automatic Heat-up function can be stopped by either
turning the control knob back to the “0” power setting or
turning the control knob to the “9” power setting.
For your guidance Table 2-2 shows the time available at
100% power depending on the power level selected in the
Automatic Heat-up mode.
Child Lock,
To prevent the unwanted use by children, the hob can be
locked.
IMPORTANT: This can only be activated when all the
cooking zones are switched o.
To lock the hob, simultaneously turn the two left-hand
controls counter-clockwise (Fig.2-6) and hold until the
symbol appears in the centre of the hob control display
(Fig.2-7).
Note: [A ] will ash when locking the hob – this is normal.
Locking the hob will NOT aect the oven; it can still be used.
To unlock the hob, simultaneously turn the two left-hand
controls counter-clockwise and hold until the
symbol
disappears from the centre of the hob control display.
Low Temperature Setting, L1/L2
Each cooking area is equipped with 2 low temperature
settings:
• L1 will maintain a temperature of about 40 °C – ideal for
gently melting butter or chocolate.
• L2 will maintain a temperature of about 90 °C – ideal for
simmering (bring the pan to the boil and then select L2
to keep soups, sauces, stews, etc at an optimal simmer).
The maximum time this setting can be used is 2 hours, after
which the hob will switch o automatically. If required, you
Table 2-2
Power level
Automatic heat-up time at
100% (min:sec)
1 0:48
2 2:24
3 3:50
4 5:12
5 6:48
6 2:00
7 2:48
8 3:36
9
Professional + FX
Fig.2-6
Fig.2-7
6
can immediately restart the Low Temperature function by
reactivating L1 or L2.
Power Boost Setting, P
All of the induction cooking zones have Power Boost
available, activated by turning the control knob clockwise
until [P ] is shown on the hob control display.
Power Boost allows additional power to be made available for
each of the cooking zones. This is useful to bring a large pan
of water to the boil quickly.
The Power Boost function operates for a maximum of 10
minutes on each zone, after which the power is automatically
reduced to setting 9.
When using the Power Boost function, the cooking zones are
linked.
Fig.2-8 shows the hob layout. Zones A and B are linked
together as are zones C, D and E.
This means that when using zone A on Power Boost and then
switching zone B to power boost, then the power to zone A
will reduce slightly. The last zone switched to Power Boost
always takes priority. Zones C, D and E work in the same way.
This is a built in safety device.
Deactivate the Power Boost function by turning the control
knob to a lower setting.
Overheat Function
This function identies when the temperature of the pan rises
rapidly and works to maintain a safe level of pan temperature.
It should not interfere with normal cooking.
Cookware with bases that become distorted (Fig.2-2) when
heated may interfere with the operation of the Overheat
Function. This may result in damage to your cookware or
Induction Glass Hob.
Please remember not to leave the hob unattended.
Care should be taken to not allow your cookware to
boil dry. Damage to your cookware and Induction
Glass Hob may result.
Please read and follow the manufacturers’ instructions
carefully before using cookware on your induction hob.
The Multi-function Oven
The oven is a multi-function oven (Fig.2-9).As well as the
oven fan and fan element, they are tted with two extra
heating elements, one visible in the top of the oven and the
second under the oven base. Take care to avoid touching
the top element and element deector when placing or
removing items from the ovens.
The multi-function oven has 3 main cooking functions: fan,
fan assisted and conventional cooking. These functions
should be used to complete most of your cooking.
The browning element and base heat can be used in the
latter part of the cooking process to ne tune the results to
your particular requirements.
Use fanned grilling for all your grilling needs and defrost to
ArtNo.326-0009 - Albertine SC - MF oven elements EU
C
A
B
Fig.2-9
A – Grill elements, B – Convection element, C – Base heat elements
Induction
A B
C
D
E
A & B linked
C, D & E linked
Fig.2-8
Function Use
Defrost
To thaw small items in the oven without
heat
Fan oven
A full cooking function, even heat
throughout, great for baking
Fanned grilling
Grilling meat and fish with the door
closed
Fan assisted
A full cooking function good for roasting
and baking
Conventional oven
A full cooking function for roasting and
baking in the lower half of the oven
Browning element
To brown and crisp cheese topped
dishes
Base heat
To crisp up the bases of quiche, pizza or
pastry
Table 2-3
7
safely thaw small items of frozen food.
Table 2-3 gives a summary of the multi-function modes.
The multi-function oven has many varied uses. We suggest
you keep a careful eye on your cooking until you are familiar
with each function. Remember, not all functions will be
suitable for all food types.
Multi-function Oven Modes (Fig.2-10)
Defrost
This function operates the fan(s) to circulate cold air
only. Make sure the temperature control is at 0°C and
that no heat is applied. This enables small items such
as desserts, cream cakes and pieces of meat, sh and poultry
to be defrosted.
Defrosting in this way speeds up the process and protects
the food from contamination. Pieces of meat, sh and poultry
should be placed on a shelf, over a tray to catch any drips. Be
sure to wash the shelf and tray after defrosting.
Defrost with the oven door closed. Defrosting should not
be carried out in a warm oven. Large items, such as whole
chickens and meat roasts should not be defrosted in this way.
We recommend this be carried out in a refrigerator.
Make sure that dairy foods, meat and poultry are completely
defrosted before cooking.
Fan Oven
This function operates the fans and the heating
element around them. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Fan oven cooking is particularly suitable for multi-shelf
cooking and is a good ‘all-round’ function. It may be
necessary to reduce the temperature by approximately 10 °C
for recipes previously cooked in a conventional oven.
If you wish to preheat the oven, wait until the indicator light
has gone out before inserting the food.
Fanned Grilling
This function operates the fan while the top element
is on. It produces a more even, less erce heat than a
conventional grill. For best results place the food to
be grilled on the pan provided. Thick pieces of meat or sh
are ideal for cooking in this way, as the circulated air reduces
the erceness of the heat from the grill. The oven door
should be kept closed while cooking is in progress, so saving
energy. You will also nd that the food needs to be watched
and turned less than for normal grilling. Preheat this function
before cooking.
Note: When grilling full width, to allow sucient access
for tending foods we recommend placing the grill pan tray
support on the second from top level.
Fan Assisted Oven
This function operates the fans, circulating air heated
by the elements at the top and the base of the oven.
The combination of fan and conventional cooking
ArtNo.270-0025
Proplus MF oven annotated
F
E
D
C
B
A G
OFF
Fig.2-10
A – Defrost, B – Fan Oven, C – Fanned Grilling, D – Fan Assisted Oven,
E – Conventional Oven, F – Browning Element, G – Base Heat
Loading...