Falcon Professional Deluxe 110 Dual Fuel User Manual & Installation & Service Instructions
110 Dual Fuel
ArtNo.000-0049 - Professional Deluxe logo
Professional
deluxe
User Guide
&
Installation & Service Instructions
U110162 - 01A
1. Before You Start... 1
Important! 1
Installation and Maintenance 1
Peculiar Smells 1
If You Smell Gas 1
Ventilation 1
Personal Safety 1
Ceramic Hotplate Care 3
Cooker Care 3
Cleaning 3
2. Cooker Overview 4
Hotplate Burners 4
Wok Burner 5
The Wok Cradle 5
The Ceramic Hotplate 6
The Griddle 7
The Glide-out Grill 8
The Ovens 9
The Clock 12
Accessories 14
Oven Lights 15
Storage 15
3. Cooking Tips 16
Tips on Cooking with the Timer 16
General Oven Tips 16
4. Cooking Table 17
5. Cleaning Your Cooker 18
Essential Information 18
Hotplate Burners 18
Ceramic Hotplate 19
The Griddle 19
Glide-out Grill 20
Control Panel and Doors 21
Ovens 21
Cleaning Table 22
6. Troubleshooting 23
7. Installation 25
Dear Installer 25
Safety Requirements and Regulations 25
Provision of Ventilation 25
Location of Cooker 25
Conversion 25
Positioning the Cooker 27
Moving the Cooker 28
Fitting the Stability Bracket or Chain 29
Repositioning the Cooker Following
Connection
29
Conversion to Another Gas 29
Levelling 29
Gas Connection 30
Electrical Connection 31
Final Checks 32
Final Fitting 32
Customer Care 32
8. Circuit Diagram 33
9. Technical Data 34
Contents
1
Your cooker should give you many years of trouble-free
cooking if installed and operated correctly. It is important
that you read this section before you start, particularly if you
have not used a dual fuel cooker before.
Important!
This appliance is designed for domestic cooking
only. Using it for any other purpose could invalidate
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen –
besides invalidating claims this wastes fuel and may
overheat the control knobs.
Installation and Maintenance
This cooker must be installed in accordance with the relevant
instructions in this booklet, with the relevant national and
local regulations, and with the local gas and electricity supply
companies’ requirements.
Make sure that the gas supply is turned on and that the
cooker is wired in and switched on (the cooker needs
electricity).
Set the clock to make sure that the oven is functional – see
the relevant section in this manual.
Only a qualied service engineer should service the cooker,
and only approved spare parts should be used.
Always allow the cooker to cool and then switch it o at the
mains before cleaning or carrying out any maintenance work,
unless specied otherwise in this guide.
Peculiar Smells
When you rst use your cooker it may give o an odour. This
should stop after use.
Before using your cooker for the rst time, make sure that all
packing materials have been removed and then, to dispel
manufacturing odours, turn all the ovens to 200 °C and run
for at least an hour.
Before using the grill for the rst time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back, and the grill door open.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
If You Smell Gas
• DO NOT turn electric switches on or off
• DO NOT smoke
• DO NOT use naked flames
• DO turn off the gas at the meter or cylinder
• DO open doors and windows to get rid of the gas
• DO keep people away from the area affected
• Call your gas supplier
Ventilation
The use of a gas cooking appliance results in the production
of heat and moisture in the room in which it is installed. Make
sure that the kitchen is well ventilated: keep natural ventilation
holes open or install a powered cookerhood that vents outside.
If you have several burners on, or use the cooker for a long
time, open a window or turn on an extractor fan.
Personal Safety
DO NOT modify this appliance.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
This appliance is not intended for use by young
children or inrm persons unless they have been
adequately supervised by a responsible person to
make sure that they can use the appliance safely.
CAUTION: A long term cooking process has to be
supervised from time to time. A short term cooking
process has to be supervised continuously.
Danger of re: DO NOT store items on the cooking
surfaces.
To avoid overheating, DO NOT install the cooker
behind a decorative door.
Accessible parts will become hot during use and will
retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and
never wear loose-tting or hanging clothes when
using the appliance.
DO NOT use a steam cleaner on your cooker.
Always be certain that the controls are in the OFF position
when the oven is not in use, and before attempting to clean
the cooker.
When the oven is on, DO NOT leave the oven door
open for longer than necessary, otherwise the
control knobs may become very hot.
1. Before You Start...
2
ArtNo.324-0001 Steam burst
When using the grill, make sure that the grill pan
is in position and pushed fully in, otherwise the
control knobs may become very hot.
Note that this appliance has a cooling fan. When an
oven or the grill is in operation the fan will run to
cool the fascia and control knobs.
DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Always keep combustible materials, e.g. curtains, and
ammable liquids a safe distance away from your cooker.
DO NOT spray aerosols in the vicinity of the cooker
while it is on.
Use dry oven gloves when applicable – using damp gloves
might result in steam burns when you touch a hot surface.
Do not use a towel or other bulky cloth in place of a glove – it
might catch re if brought into contact with a hot surface.
NEVER operate the cooker with wet hands.
DO NOT use aluminium foil to cover shelves, linings
or the oven roof.
NEVER heat unopened food containers. Pressure
build up may make the containers burst and cause
injury.
DO NOT use unstable saucepans. Always make sure
that you position the handles away from the edge of
the hotplate.
DO NOT use cooking vessels on the hotplate that
overlap the edges.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on re. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
WARNING!
Unattended cooking on a hob with fat or oil can be
dangerous and may result in re.
NEVER leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
Do not use the top of the ue (the slot along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.
Fig.1-1
3
DO NOT use water on grease res and never pick
up a aming pan. Turn the controls o and then
smother a aming pan on a surface unit by covering
the pan completely with a well tting lid or baking
tray. If available, use a multi-purpose dry chemical
or foam-type re extinguisher.
Cooking high moisture content foods can create a ‘steam
burst’ when the oven door is opened (Fig.1-1). When
opening the oven stand well back and allow any steam to
disperse.
Take care that no water seeps into the appliance.
This appliance is heavy so take care when moving it.
Ceramic Hotplate Care
NEVER cook directly on the hotplate surface.
DO NOT use the hob surface as a cutting board.
Do not leave utensils, foodstus or combustible items on
the hob when it is not in use (e.g. tea towels, frying pans
containing oil).
DO NOT place plastic or aluminium foil, or plastic
containers, on the hotplate.
DO NOT leave the hotplate switched on unless being
used for cooking.
Do not stand or rest heavy objects on the hotplate. Although
the ceramic surface is very strong, a sharp blow or sharp
falling object (e.g. a salt cellar) might cause the surface to
crack or break (Fig.1-2).
Should a crack appear in the surface, disconnect the
cooker immediately from the supply and arrange for
its repair.
Always LIFT pans o the hotplate. Sliding pans may cause
marks and scratches (Fig.1-3). Always turn the control to the
‘OFF’ position before removing a pan.
DO NOT place anything between the base of the pan and
the hotplate surface (e.g. asbestos mats, aluminium foil, wok
stand).
Avoid heating an empty pan. Doing so may damage
both the hotplate and pan.
Only certain types of glass, glass-ceramic, earthenware or
other glazed containers are suitable for hotplate cooking;
others may break because of the sudden change in
temperature.
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours.
ArtNo.312-0003 Moving pans
Fig.1-2
Fig.1-3
4
Professional
Deluxe
A
B
C
D
E
F
2. Cooker Overview
The 110 dual fuel cooker (Fig.2-1) has the following features:
A. 5 hotplate burners including a wok burner and ceramic
multizone hotplate
B. A control panel
C. A glide-out grill
D. A multi-function oven
E. A fan oven
F. A storage drawer
Hotplate Burners
The drawing by each of the central knobs indicates which
burner that knob controls.
Each burner has a Flame Supervision Device (FSD) that
prevents the ow of gas if the ame goes out.
When a hotplate control knob is pressed in, sparks will be
made at every burner – this is normal. Do not attempt to
disassemble or clean around any burner while another
burner is on, otherwise an electric shock could result.
To light a burner, push in and turn the associated control
knob to the high position as indicated by the large ame
symbol (H), (Fig.2-2).
Fig.2-2
Fig.2-1
DocNo.020-0006 - Overview - 100DF - Prof+
5
ArtNo.311-0007 Wok stand close-up
ArtNo.311-0006 Correct wok sizes
Fig.2-10
Fig.2-9
ArtNo.311-0002 Pan with rim
The igniter should spark and light the gas. Keep holding the
knob pressed in to let the gas through to the burner for about
ten seconds.
If, when you let go of the control knob, the burner goes out,
then the FSD has not been bypassed. Turn the control knob
to the OFF position and wait for one minute before you try
again, this time making sure to hold in the control knob for
slightly longer.
Adjust the ame height to suit by turning the knob counterclockwise (Fig.2-3). On this cooker the low position is beyond
high, NOT between high and o.
If a burner ame goes out, turn o the control knob and
leave it for one minute before relighting it.
Make sure that the ames are under the pans. Using a lid will
help the contents boil more quickly (Fig.2-4).
Large pans should be spaced well apart.
Pans and kettles with concave bases or down-turned base
rims should not be used (Fig.2-5).
Simmering aids, such as asbestos or mesh mats, are
NOT recommended (Fig.2-6). They will reduce burner
performance and could damage the pan supports.
You should also avoid using unstable and misshapen pans
that may tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers (Fig.2-7).
The minimum recommended pan diameter is 120 mm. The
maximum allowable pan base diameter is 250 mm.
DO NOT use cooking vessels on the hotplate that overlap the
edges.
Wok Burner
The wok burner is designed to provide even heat over a large
area. It is ideal for large pans and stir-frying (Fig.2-8).
For heating smaller pans, the aforementioned hotplate
burners may be more ecient.
You should wipe the enamel top surface of the cooker around
the hotplate burners as soon as possible after spills occur. Try
to wipe them o while the enamel is still warm.
Note:
The use of aluminium pans may cause metallic marking
of the pan supports. This does not aect the durability of the
enamel and may be cleaned o with a suitable metal cleaner.
The Wok Cradle
The wok cradle is designed to t a 35 cm wok. If you use a
dierent wok, make sure that it ts the cradle. Woks vary very
widely in size and shape. It is important that the wok sits
down on the pan support – however, if the wok is too small,
the cradle will not support it properly (Fig.2-9).
The cradle should be used on the triple ring wok burners
only. When you t the cradle, check that it is supported
properly on a pan support and that the wok is sitting level in
the cradle (Fig.2-10).
The cradle will get very hot in use – allow plenty of time for it
to cool before you pick it up.
Fig.2-5
ArtNo.311-0001 Right pans gas
Fig.2-4
ArtNo.270-0003
Proplus control to low
Fig.2-3
Art No. 311-0003 Simmer aids
Fig.2-6
ArtNo.311-0004 Tipping wok
Fig.2-7
Fig.2-8
6
The Ceramic Hotplate
The hotplate area on the left-hand side is dual purpose. It can
be used either as a ceramic hob to heat a pan in the usual
way (Fig.2-11) or it can be used to heat the supplied griddle.
The rear area, marked with a ring, is for cooking with a pan.
There are two elements that allow either the whole of the
area to be heated or just the rear half.
To heat the whole area, turn the hotplate control clockwise
(Fig.2-12).
To use the rear ring only, turn the hotplate control counterclockwise (Fig.2-13).
The neon indicator light above the control knob will come on
when the hotplate control is turned on and stay lit while the
surface cools.
You can also place a large sh kettle across both heating
zones.
Always take care before touching the surface even when
it is turned o – it may be hotter than you think.
Use only pans that are suitable for ceramic hobs.
We recommend stainless steel and enamelled steel pans
because pots and pans with copper or aluminium bases leave
traces on the hob that are dicult to remove.
Pots and pans should have thick, smooth, at bottoms
(Fig.2-14). This makes sure the maximum heat transfer
from the hob to the pan, making cooking quick and energy
ecient. Never use a round-bottomed wok, even with a
stand.
The very best pans have bases that are very slightly curved up
when cold. If you hold a ruler across the bottom you will see
a small gap in the middle (Fig.2-15). When they heat up the
metal expands and lies at on the cooking surface.
Make sure that the base of the pan is clean and dry to prevent
any residue burning onto the hob panel. This also helps
prevent scratches and deposits.
Always use pans that are the same size as (or slightly larger
than) the areas marked on the hob top (Fig.2-16). Using
smaller pans wastes heat, and any spillage will be burnt on.
Using a lid will help the contents boil more quickly.
Always lift pans o the hob. Sliding pans may cause marks
and scratches. Always turn the control to the ‘OFF’ position
before removing a pan.
When cooking on the hob you may see the hob area you
are using switch o and on. This is caused by a safety device
that limits the temperature of the hob. It is quite normal,
especially when cooking at high temperatures. If it happens a
lot with a particular pan however it may mean the pan is not
suitable – perhaps too small or too uneven – for a ceramic
hob.
For best results, preheat a covered serving dish for 10 minutes
before adding food to it.
Use only heat-resistant dishes.
ArtNo.274-0008
Prof DL warmer control 1
1
1
2
2
3
3
0
Fig.2-11
Fig.2-12
ArtNo.312-0004 Correct pans ceramic
ArtNo.312-0005 Curved
bottomed pan ceramic
Fig.2-14
Fig.2-15
Fig.2-13
ArtNo.274-0007
Prof DL warmer control 1
1
1
2
2
3
3
0
7
ArtNo.312-0006 Correct pan sizes
Fig.2-20
The Griddle
The griddle (Fig.2-17) is designed to t securely on the
locating pins over the ceramic heating area (Fig.2-18). DO
NOT try to use it over one of the gas burners. It will not be
securely held and you may damage the non-stick nish.
To heat the whole area, turn the hotplate control clockwise
(Fig.2-19).
The neon indicator light above the control knob will come on
when a hob control is turned on and stay lit while the surface
cools.
It is designed for cooking food on directly. DO NOT use pans
of any kind on it. The griddle surface is non-stick and metal
cooking utensils (e.g. spatulas) will damage the surface. Use
heat resistant plastic or wooden utensils.
The griddle can be lightly brushed with cooking oil before
use.
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage.
There is a gap at the right-hand rear corner of the griddle
(Fig.2-20) so you can pour o excess fat after cooking.
Be careful – it may be very hot.
After cooking, allow the griddle to cool before cleaning.
Fig.2-18
ArtNo.274-0007
Prof DL warmer control 1
1
1
2
2
3
3
0
Fig.2-16
Fig.2-17
Fig.2-19
8
The Glide-out Grill
Open the door and pull the grill pan carriage forward using
the handle (Fig.2-21).
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
To heat the whole grill, turn the knob clockwise (Fig.2-22).
To heat the right-hand half, turn the knob counter-clockwise.
The neon indicator light by the grill control will come on.
For best results, slide the carriage back into the grill chamber
and preheat the appropriate part(s) of the grill for two
minutes. The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
DO NOT leave the grill on for more than a few
moments without the grill pan underneath it,
otherwise the knobs may become hot.
Once the grill has preheated, slide the carriage out again.
With the trivet back in place with the food on it, slide the
carriage back into the grill chamber. Make sure that it is
pushed right in.
Accessible parts may be hot when the grill is in use.
Young children should be kept away.
The grill pan trivet can be turned over to give two grilling
positions (Fig.2-23).
Never close the grill door when the grill is on.
ArtNo.331-0001Grill pan pulled forwards
ArtNo.270-0004
Proplus grill control
1
1
2
2
3
3
0
Fig.2-21
Fig.2-22
ArtNo.331-0002 Grill pan high/low position
Fig.2-23
9
The Ovens
The clock must be set to the time of day before the ovens
will work. See the following section on ‘The Clock’ for
instructions on setting the time of day.
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
The left-hand oven is a multi-function oven, while the righthand oven is a fan oven.
The Multi-function Oven
As well as the oven fan and fan element, multi-function
ovens are tted with two extra heating elements, one visible
in the top of the oven and the second under the oven base.
Take care to avoid touching the top element and element
deector when placing or removing items from the ovens.
The multi-function oven has 3 main cooking functions: fan,
fan assisted and conventional cooking. These functions
should be used to complete most of your cooking.
The browning element and base heat can be used in the
latter part of the cooking process to ne tune the results to
your particular requirements.
Use fanned grilling for all your grilling needs and defrost to
safely thaw small items of frozen food.
Table 2-1 gives a summary of the multi-function modes.
The multi-function ovens have many varied uses. We suggest
you keep a careful eye on your cooking until you are familiar
with each function. Remember – not all functions will be
suitable for all food types.
Please remember that all cookers vary – temperatures in your
new ovens may dier to those in your previous cooker.
Function Use
Defrost
To thaw small items in the oven without
heat
Fan oven
A full cooking function, even heat
throughout, great for baking
Fanned grilling
Grilling meat and fish with the door
closed
Fan assisted
A full cooking function good for roasting
and baking
Conventional oven
A full cooking function for roasting and
baking in the lower half of the oven
Browning element
To brown and crisp cheese topped
dishes
Base heat
To crisp up the bases of quiche, pizza or
pastry
Table 2-1
10
Multi-function Oven Functions
Rapid Response
The Rapid Response setting enables you to preheat
the oven faster than normal. It uses the fan oven
element with additional heat from one of the
elements in the top of the oven. The fan ovens heat up
quickly; but the Rapid Response feature speeds this process
up enabling you to start cooking sooner.
To use the Rapid Response feature, simply turn the function
control knob to R and set the temperature you require. The
light on the control panel next to the R symbol will come
on. When temperature is reached, the light will go out as
will the element at the top of the oven. The fan element and
oven fan will then continue to maintain your chosen oven
temperature.
Should you choose to place food into the cold oven prior
to cooking whilst using the Rapid Response function, make
sure that cakes etc. are not positioned too near the top of the
oven. As with any cooking, particularly poultry, meat and
ready meals, be sure the food is piping hot before serving.
Fan Oven
This function operates the fan and the heating
element around it. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Fan oven cooking is particularly suitable for baking on several
shelves at one time and is a good ‘all-round’ function. It may
be necessary to reduce the temperature by approximately
10 °C for recipes previously cooked in a conventional oven.
If you wish to preheat the oven, wait until the indicator light
has gone out before inserting the food.
Fanned Grilling
This function operates the fan whilst the top element
is on. It produces a more even, less erce heat than a
conventional grill. For best results, place the food to
be grilled on a trivet over a roasting tin, which should be
smaller than a conventional grill pan. This allows greater air
circulation. Thick pieces of meat or sh are ideal for grilling in
this way, as the circulated air reduces the erceness of the
heat from the grill.
The oven door should be kept closed while grilling is in
progress, so saving energy. You will also nd that the food
needs to be watched and turned less than for normal grilling.
Preheat this function before cooking.
Fan Assisted Oven
This function operates the fan, circulating air heated
by the elements at the top and the base of the oven.
The combination of fan and conventional cooking
(top and base heat) makes this function ideal for cooking large
items that need thorough cooking, such as a large meat roast.
It is also possible to bake on two shelves at one time,
although they will need to be swapped over during the
cooking time, as the heat at the top of the oven is greater
than at the base, when using this function.
This is a fast intensive form of cooking; keep an eye on the
food cooking until you have become accustomed to this
function.
Conventional Oven (Top and Base Heat)
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits.
Food cooked on the top shelf will brown and crisp faster than
on the lower shelf, because the heat is greater at the top of
the oven than at the base, as in ‘Fan Assisted Oven’ function.
Similar items being cooked will need to be swapped around
for even cooking. This means that foods requiring dierent
temperatures can be cooked together, using the cooler zone
in the lower half of the oven and hotter area to the top.
The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.
Browning Element
This function uses the element in the top of the oven
only. It is a useful function for the browning or
nishing of pasta dishes, vegetables in sauce,
shepherds pie and lasagne, the item to be browned being
already hot before switching to the top element.
Base Heat
This function uses the base element only. It will crisp
up your pizza or quiche base or nish o cooking the
base of a pastry case on a lower shelf. It is also a
gentle heat, good for slow cooking of casseroles in the
middle of the oven or for plate warming.
The Browning and Base Heat functions are useful additions
to your oven, giving you exibility to nish o items to
perfection.
Defrost
This function operates the fan to circulate cold air
only. No heat is applied. This enables small items such
as desserts, cream cakes and pieces of meat, sh and
poultry to be defrosted.
Defrosting in this way speeds up the process and protects
the food from ies. Pieces of meat, sh and poultry should be
placed on a trivet, over a tray to catch any drips. Be sure to
wash the trivet and tray after defrosting.
Defrost with the oven door closed.
Large items, such as whole chickens and joints should not be
defrosted in this way. We recommend this be carried out in a
refrigerator.
Defrosting should not be carried out in a warm oven or when
an adjoining oven is in use or still warm.
Make sure that dairy foods, meat and poultry are completely
defrosted before cooking.
Loading...