Falcon Predator XL3 Installer Manual
-
FALCON
WOR LD CLASS SE CUR ITY
FALCON PREDATOR XL3
Vehicle Security System with Anti-Hijack
Installer’s Manual
TABLE OF CONTENTS
1. SYSTEM INSTALLATION............................................... 2
1.1. Power On ........................................................... 2
1.2. NO & NC Immobiliser Relay Wiring......................... 2
1.3. Programming New Remote Controls ....................... 2
1.4. Bypass Input (red/black wire: w3-7)...................... 2
1.5. Start Output (pink wire: w3-9).............................. 2
1.6. Interior Light Supervision (green/white wire: w3-6).. 3
1.7. Program the Optional Features (default=1 chirp)...... 3
1.8. Optional Programmable Features ........................... 3
1.9. Feature #20 Override Code (default=1 flash) .......... 4
1.10. Explanation of the Optional Features.....................4
2. SYSTEM UPGRADE...................................................... 8
3. Wiring Diagram.......................................................... 9
4. Wiring Notes............................................................ 10
5. Central Locking Wiring.............................................. 11
1. SYSTEM INSTALLATION
1.1. Power On
When powered on, the system will remain in the same status it was in when powered off.
1.2. NO & NC Immobiliser Relay Wiring
The system offers two ways of wiring the immobiliser as shown below.
When wired for Normally Open the immobiliser relay is switched on when the alarm is disarmed
(fail secure). When wired as Normally Closed the relay is on when the alarm is arme d (fail safe).
Wiring Diagram - Immobiliser Relay NO & NC
Normally Closed Immobiliser Connection (Fail Safe)
87a - Normally Closed
87 - Normally Open
Off
Acc
On
Start
86
85
87
87a
30
To +12V DC or Acc.
W2-8
fig. 2
Normally Open Immobiliser Connection (Fail Secure)
87a - Normally Closed
87 - Normally Open
Off
Acc
On
Start
86
85
87
87a
30
To Acc.
W2-7
fig. 1
1.3. Programming New Remote Controls
The included remote controls have been programmed to the system in the factory. Follow the
procedure below to program a new remote control to the system:
- Turn the ignition on with the system disarmed.
- Within 10 seconds, press valet switch 3 times. (or 6 times if pager upgrade is installed).
- The siren sounds for 2 sec. to confirm the system is now in code learning mode.
- Within 10 sec., press any button of 1
st
remote control
The siren will sound for 1 sec. and hazard lights flash twice to confirm the 1
st
remote has been
programmed to the system and all the previous codes in the system will be erased entirely.
- Within 10 sec., repeat for the 2nd remote control and again for 3rd and 4th remotes as
applicable.
* Up to 4 remotes can be programmed to the system
* The system will leave the code learning mode after programming 4 remotes to the system
and the siren will sound for 2 seconds to confirm.
* If no buttons are pressed within 10 seconds, the system will leave the learning code mode
and the siren will sound for 2 seconds to confirm.
* The system will leave the code learning mode if the ignition is turned off at any time and the
siren will sound for 2 seconds to confirm.
1.4. Bypass Input (red/black wire: w3-7)
This wire is designed for external engine start module or turbo timer. Feed this wire with
ground when the external engine start module or turbo timer is activated and the system will
bypass the ignition input and shock sensor until the ground pulse is removed.
1.5. Start Output (pink wire: w3-9)
Press and hold button #4, 3 sec. later the system will send a 1 sec. pulse to activate the
external engine start module. Pressing button #4 for 3 sec. will send the pulse again to
deactivate the external engine start module.
-
1.6. Interior Light Supervision (green/white wire: w3-6)
If connected:
- The interior light will be turned on for 20 sec. when disarming unless the ignition is turned
on.
- The interior light will be turned on all the time whilst the alarm is sounding.
1.7. Program the Optional Features (default=1 chirp)
Follow the steps below to program the Optional Features:
For example: To program the feature #5 as 15sec.
- Turn the ignition on then off with the system disarmed.
- Within 10 sec., press the valet switch 3 times.
- The system enters the programming mode and the siren and LED will be on for 2 sec. to
confirm.
* To Reset to Factory Default:
Within 10 seconds press button #4 for 3 sec., all the optional features will be reset to the
factory default and the siren will sound for 2 sec. to confirm leaving the programming
mode.
- Within 10 sec., press the valet switch 5 times.
- 1 sec. later the siren will chirp 5 times to confirm.
- Press button #1 of the remote control 6 times to select 15 sec. and the siren will chirp 6
times to confirm the setting.
- Press the valet switch again (from 1 to 21) within 10 sec. to select the next feature for
programming.
* The system will leave the programming mode and the siren will sound for 2 sec. to confirm
if the ignition is turned off at any time during progr amming or if the vale t switch or remote
control button #1 has not been pressed within 10 sec.
1.8. Optional Programmable Features
No Chirp Function Τ 1 Chirp Τ 2 Chirp Τ 3 Chirp Τ 4 Chirp
1 1 chirp Chirp Confirmation On Off
2 2 chirp Door Lock with Passive Arming Disable Enable
3 3 chirp Ignition Lock Disable Ignition Brake
4 4 chirp Ignition Unlock Disable Driver All
5 5 chirp Door Lock Time(sec.) 1) 0.8 2) 3.6 3) 0.8*2 4) 0.8+15
5) 0.8+40 6) 15 7) 40
6 6 chirp Door Unlock Time(sec.) 0.8 3.6 0.8*2
7 7 chirp Door Unlock with Disarming Driver All
8 8 chirp Siren/Horn Output Siren Horn
9 9 chirp Alarm Condition Cycle Duration 30 sec. 60 sec.
10 10 chirp Interior Light Delay Disable 25 sec. 40 sec. 60 sec.
11 11 chirp Auto. Rearming Disable Enable
12 12 chirp Auto. Engine Disable(AED) Disable Enable
13 13 chirp Door Open Alerts Disable Mode 1 Mode 2
14 14 chirp Total/Comfort Closure Disable 15 sec. 30 sec. 40 sec.
15 15 chirp Disarm with Boot Release Disable Enable
16 16 chirp Anti-hijacking Countdown 30sec. 60sec.
17 17 chirp Activate Anti-hijacking Countdown Nor mal Brake
18 18 chirp Anti-hijacking by Remotes Disable Enable
19 19 chirp Anti-hijacking by Ignition+Door Disable Enable
20 20 chirp Override Code Flash 1 Flash 2~10
21 21 chirp Hazard lights Output Normal Pulse Continuous
Factory Default = 1 Chirp
-
1.9. Feature #20 Override Code (default=1 flash)
Follow the steps below to program:
- Turn the ignition on then off with the system disarmed.
- Within 10 sec., press the valet switch 3 times.
- The system enters the programming mode and the siren and LED will be on for 2 sec. to
confirm.
- Within 10 seconds press the valet switch 20 times to select feature #20
- 1 sec. later the siren will chirp 20 times to confirm the selection.
- The LED will start to flash 10 times slowly 2 sec. later.
- Press button #1 of remotes after the LED has flashed the number of times you want to set
the code to; Eg. If you want to choose 6 as the code then press button #1 once after the
LED has flashed 6 times. The LED will turn off and siren sound for 1 sec. to confirm.
- Press the valet switch within 10 sec., to select the next feature for programming.
1.10. Explanation of the Optional Features
01. Chirp Confirmation On/Off(default=on)
When On:
The siren will chirp once for system arming and twice for disarming. With this feature on, the
silent arm/disarm button is still functional.
When Off:
The siren will not chirp for system arming and disarming but the hazard lights will flash as
normal.
02. Door Lock with Passive Arming(default=disable)
When Enabled:
The doors will also be locked when the system passively arms itself.
03. Ignition Lock (default=disabled)
When set as Ignition:
- The doors will be locked 15 sec. after turning the ignition on if all the doors are closed
properly.
- The doors will not be locked if a door is not closed or has been opened during the 15 sec.
countdown.
- If the doors are unlocked during driving they will be locked again automatically after
stepping on the brake pedal. (Brake light wire must be connected).
When set as Brake: (Brake light wire must be connected)
- The doors will be locked when the brake is tapped with the ignition on if all the doors are
closed properly.
- If the doors are unlocked during driving they will be locked again automatically after
stepping on the brake pedal.
04. Ignition Unlock(default=disable)
When set as Driver:
After parking the car the drivers door will be unlocked when turning the ignition off.
When set as All:
After parking the car all the doors will be unlocked after turning the ignition off.
05. Door Lock Time (default=0.8)
When set as 0.8 sec.:
The system will send a 0.8 sec. pulse when locking the doors.
When set as 3.6 sec.:
The system will send a 3.6 sec. pulse when locking the doors.
When set as 0.8 sec.*2:
The system will send two 0.8 sec. pulses when locking the doors.
When set as 0.8 sec. + 15 sec.:
The system will send a 0.8 sec. pulse and then send a 15 sec. pulse when locking the doors.
Loading...