Falcon Kitchener, Professional + User's Manual & Installation Instructions

Download

Page 1

USER GUIDE &

INSTALLATION INSTRUCTIONS

Kitchener & Professional +

90 Dual Fuel

Australia

U110138-07A

Page 2

SLOW BAKED LEG OF LAMB

INGREDIENTS

• 2-3 large sprigs of rosemary

• 4 large garlic cloves cut in half lengthways

• 1.8 kg leg of lamb

• 8 good quality anchovy llets, halved

• 100 ml olive oil

• 250 ml dry red wine

• Maldon salt and freshly ground black pepper

METHOD

1. Preheat the oven to 220 °C (for a conventional oven), 200 °C (for a

fan oven) or gas mark 7.

2. Pull the small sprigs o the rosemary branches and set aside with the garlic.

3. Using the tip of a paring knife, make up to 20 well-spaced cuts into the esh of the lamb, about 2.5 cm inch deep. Divide the rosemary sprigs, garlic and anchovies and push down into the cuts. Place the leg on a large roasting tin and pour over the oil, massaging it all over the joint. Season well with salt and pepper and pour the wine and 250 ml water into the tin.

4. Put into the oven and sear for 15 minutes, then turn the temperature right down to 130 °C (conventional oven), 110 °C (fan oven) or gas mark 1 and roast for 4-5 hours, basting every 30minutes or so. Basting frequently helps to keep the meat moist and encourages the build up of a good glaze on the outside. Add more liquid (wine or water) if the tin looks dry Ð there should always be liquid in the tin throughout this cooking process.

5. The meat is ready when it starts to fall o the bone, at which point it should have a core temperature of 90 °C. Remove from the oven, transfer to a warmed carving dish, cover loosely with foil and leave to rest in a warm place for 30-45 minutes before carving.

6. Pour the juices from the tin into a tall hi-ball glass and allow to settle. Spoon the fat from the top of the glass. There should be enough sticky, reduced juices for an intense gravy hit if not, pour the juices you have back into the roasting tin and put it over the heat, pour in a splash of water or wine and deglaze the tin scraping up all the sticky bits from the base. Boil fast until syrupy, taste and correct the seasoning.

RASPBERRY SOUFFLÉ

INGREDIENTS

• 400 g raspberries

• 1 tbsp lemon juice

• 100 g caster sugar

• 2 tsp créme de framboise

• 1 tsp cornour

• 180 g egg whites (about 6)

• Pinch of cream of tartar or a squeeze of lemon juice

• Icing sugar for dusting

METHOD

1. For the soué, press the raspberries through a ne sieve to

produce 180 g of purée. Put this into a heavy-bottomed pan, add the lemon juice and reduce down to a thick jam, stirring from time to time and being careful not to let it catch and burn.

2. Put 45 g of the sugar in a separate pan. Melt it and then boil until it becomes a thick syrup (121°C on a sugar thermometer). To test without a thermometer, dip a teaspoon into the syrup and then dip quickly into cold water. You should be able to roll the cooling syrup into a ball between your ngers. Be careful as the syrup is extremely hot. When it has reached the right point, stir the hot syrup into the raspberry jam.

3. Mix the framboise and cornour together and stir into the jam over the heat. Turn the jam into a small bowl, sprinkle the surface with icing sugar and cover with cling lm.

4. Preheat the oven (not grill) to 180 °C shelf level 2 (conventional oven), 160 °C (fan oven) or gas mark 4 centre shelf.

5. Whisk the egg whites with the cream of tartar until you can

form soft peaks, then fold in the remaining caster sugar. Lightly fold the whites into the jam, leaving thin traces of white visible in the mixture.

6. Spoon into four large buttered and sugared ramekins, place these on a baking tray and bake for 10 minutes.

7. Dust with icing sugar.

Page 3

Contents

1. Before You Start... 1

Installation and Maintenance 1 Peculiar Smells 1 If You Smell Gas 1 Ventilation 1 Personal Safety 1 Cleaning 2

2. Cooker Overview 3

Hotplate Burners 3 The Wok Cradle (optional) 5 The Griddle The Grill / Glide-out Grill 6 The Ovens 7 Accessories 8 Main Oven Light 8

(optional) 5

3 The Clock 9

4 Cooking Tips 14

6. Troubleshooting 20

7. Installation 22

Service and Spares 22 Safety Requirements and Regulations 23 Provision of Ventilation 23 Location of Cooker 23 Conversion 23 Positioning the Cooker 25 Moving the Cooker 25 Completing the Move 26 Levelling the Cooker 26 Fitting the Stability Bracket and Chain 26 Gas Connection 27 Pressure Testing 27 Electrical Connection 28 Final Checks 29 Final Fitting 29 Customer Care 29

Tips on Cooking with the Timer 14

General Oven Tips 14

5. Cooking Table 15

5. Cleaning Your Cooker 16

Essential Information 16 Hotplate Burners 16 Grills 17 Control Panel and Doors 17 Ovens 18 The Tall Oven 18 Cleaning Table 19

8. Conversion to Propane Gas 30

Conversion from Natural Gas (1.0 kPa) to LPG X Propane (2.54 kPa)

Injectors 30 Tap Adjustment 30 Set the Governor 31 Pressure Testing 31 Ax Label 31

9. Servicing 32

10. Circuit Diagram 38

11. Technical Data 39

Kitchener and Professional+ 90 Dual Fuel

iii

Page 4

Page 5

1. Before You Start...

Your cooker should give you many years of trouble-free cooking if installed and operated correctly. It is important that you read this section before you start.

Personal Safety

This appliance is for cooking purposes only. It must not be used for other purposes, for example heating a room. Using it for any other purpose could invalidate any warranty or liability claim. Besides invalidating claims this wastes fuel and may overheat the control knobs.

This cooker must be installed in accordance with the relevant instructions in this booklet and with the national and local regulations as well as the local gas and electricity supply companies’ requirements.

• This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children less than 8 years of age should be kept away unless continuously supervised. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• This appliance is designed for domestic cooking only. Use for any other purpose could invalidate any warranty or liability claim.

• The appliance and its accessible parts become hot during use and will retain heat even after you have stopped cooking. Care should be taken to avoid touching heating elements.

• DO NOT use a steam cleaner on your cooker.

• Always keep combustible materials, e.g. curtains, and

flammable liquids a safe distance away from the cooker.

• DO NOT spray aerosols in the vicinity of the cooker while it is on.

Gas Connection Safety

• This cooker is a Class 2 Subclass 1 appliance.

• This appliance can be converted for use on another gas.

• Before installation, make sure that the cooker is suitable

for your gas type and supply voltage. See the data badge.

• DO NOT use reconditioned or unauthorised gas controls.

• Disconnect from the electricity and gas supply before servicing.

• When servicing or replacing gas-carrying components disconnect from the gas supply before starting operation. Check the appliance is gas sound after completion.

• Make sure that the gas supply is turned on and that the cooker is wired in and switched on.

• In your own interest and that of safety, it is law that all gas appliances be installed by a qualified person(s).

• An appliance for use on LPG must not be installed in a room or internal space below ground level, e.g. in a basement.

• A long term cooking process has to be supervised from time to time. A short term cooking process has to be supervised continuously.

• At the risk of fire DO NOT store items on the cooking surfaces.

• DO NOT place articles on or against this appliance.

• DO NOT install an aftermarket lid or cover over this

appliance.

• DO NOT install combustible bench top lids or covers within 200 mm of the nearest burner.

• To avoid overheating, DO NOT install the cooker behind a decorative door.

• Accessible parts will become hot during use and will retain heat even after you have stopped cooking. Keep babies and children away from the cooker and never wear loose-fitting or hanging clothes when using the appliance.

If You Smell Gas

• DO NOT turn electric switches on or off

• DO NOT smoke

• DO NOT use naked flames

• Turn off the gas at the meter or cylinder

• Open doors and windows to get rid of the gas

• Keep people away from the area affected

• Call your gas supplier

Page 6

Peculiar Smells

Maintenance

When you rst use your cooker it may give o an odour. This should stop after use.

Before using for the rst time, make sure that all packing materials have been removed and then, to dispel manufacturing odours, turn the ovens to 200 °C and run for at least an hour.

Before using the grill for the rst time you should also turn on the grill and run for 30 minutes with the grill pan in position, pushed fully back and the grill door open.

Make sure the room is well ventilated to the outside air (see ‘Ventilation’ below). People with respiratory or allergy problems should vacate the area for this brief period.

Ventilation

The use of a cooking appliance results in the production of heat and moisture in the room in which it is installed. Therefore, make sure that the kitchen is well ventilated: keep natural ventilation holes open or install a powered cookerhood that vents outside. If you have several hotplates/ burners on, or use the cooker for a long time, open a window or turn on an extractor fan

• Only a qualified service engineer should service the appliance and only approved spare parts should be used. It is recommended that this appliance is serviced annually.

• DO NOT use cooking vessels on the hotplate that overlap the edges.

• Unless specified otherwise in this guide, always allow the appliance to cool and then switch it off at the mains before cleaning or carrying out any maintenance work.

• DO NOT use the control knobs to manoeuvre the cooker.

• NEVER operate the cooker with wet hands.

• DO NOT use a towel or other bulky cloth in place of a

glove – it might catch fire if brought into contact with a hot surface.

• DO NOT use hotplate protectors, foil or hotplate covers of any description. These may affect the safe use of your hotplate burners and are potentially hazardous to health.

• NEVER heat unopened food containers. Pressure build up may make the containers burst and cause injury.

• DO NOT use unstable saucepans. Always make sure that you position the handles away from the edge of the hotplate.

• NEVER leave the hotplate unattended at high heat settings. Pans boiling over can cause smoking, and greasy spills may catch on fire. Use a deep fat thermometer whenever possible to prevent fat overheating beyond the smoking point.

• Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.

• NEVER leave a chip pan unattended. Always heat fat slowly, and watch as it heats. Deep fry pans should be only one third full of fat.

• NEVER try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool. Filling the pan too full of fat can cause spill over when food is added. If you use a combination of oils or fats in frying, stir them together before heating, or as the fats melt.

• Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan. Carefully watch for spills or overheating of foods when frying at high or medium high temperatures.

• DO NOT use the top of the flue (the slot along the back of the cooker) for warming plates, dishes, drying tea towels or softening butter.

• DO NOT use water on grease fires and never pick up a flaming pan. Turn the controls off and then smother

Page 7

a flaming pan on a surface unit by covering the pan completely with a well fitting lid or baking tray. If available, use a multi-purpose dry chemical or foamtype fire extinguisher.

• DO NOT modify this appliance. This appliance is not intended to be operated by means of external timer or separated remote-control system.

• If flammable materials are stored in the drawer, oven(s) or grill(s) it may explode and result in fire or property damage.

Oven Care

• When the oven is not in use and before attempting to clean the cooker always be certain that the control knobs are in the OFF position.

• Use oven gloves to protect your hand from potential burns.

• Cooking high moisture content foods can create a ‘steam burst’ when the oven door is opened (Fig. 1.1). When opening the oven, stand well back and allow any steam to disperse.

Fig. 1.1

ArtNo.324-0001 Steam burst

• The inside door face is constructed with toughened safety glass. Take care NOT to scratch the surface when cleaning the glass panel.

• Accidental damage may cause the door glass panel to fracture.

• Keep oven vent ducts unobstructed.

• DO NOT use harsh abrasive cleaners or sharp metal

scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.

• Make sure the shelves are pushed firmly to the back of the oven. DO NOT close the door against the oven shelves.

• DO NOT use aluminium foil to cover shelves, linings or the oven roof.

• When the oven is on, DO NOT leave the oven door open for longer than necessary, otherwise the control knobs may become very hot.

• DO NOT use the timed oven if the adjoining oven is already warm.

• DO NOT place warm food in the oven to be timed.

• DO NOT use a timed oven that is already warm.

• Use dry oven gloves when applicable – using damp

gloves might result in steam burns when you touch a hot surface.

Page 8

Grill/Glide-out Grill™ Care

Cleaning

• When using the grill, make sure that the grill pan is in position and pushed fully in, otherwise the control knobs may become very hot.

• DO NOT leave the grill on for more than a few moments without the grill pan underneath it, otherwise the knobs may become hot.

• NEVER close the grill door when the grill is on.

• Accessible parts may be hot when the grill is in use.

Young children should be kept away.

Cooling Fan

This appliance may have a cooling fan. When the grill or oven is in operation the fan will run to cool the fascia and control knobs.

Cooker Care

As steam can condense to water droplets on the cool outer trim of the oven, it may be necessary during cooking to wipe away any moisture with a soft cloth. This will also help to prevent soiling and discolouration of the oven exterior by cooking vapours.

• Isolate the electricity supply before carrying out any thorough cleaning. Allow the cooker to cool.

• In the interests of hygiene and safety, the cooker should be kept clean at all times as a build up in fats and other food stuff could result in a fire.

• Clean only the parts listed in this guide.

• Clean with caution. If a wet sponge or cloth is used to

wipe spills on a hot surface, be careful to avoid steam burns. Some cleaners can produce noxious fumes if applied to a hot surface.

• NEVER use paint solvents, washing soda, caustic cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt.

• DO NOT mix different cleaning products – they may react together with hazardous results.

• All parts of the cooker can be cleaned with hot soapy water.

• Take care that no water seeps into the appliance.

• Before you remove any of the grill parts for cleaning,

make sure that they are cool or use oven gloves.

• DO NOT use any abrasive substances on the grill and grill parts.

• DO NOT put the side runners in a dishwasher.

• DO NOT put the burner heads in a dishwasher.

• NEVER use caustic or abrasive cleaners as these will

damage the surface.

• DO NOT use steel wool, oven cleaning pads or any other materials that will scratch the surface.

• NEVER store flammable materials in the drawer. This includes paper, plastic and cloth items, such as cookbooks, plastic ware and towels, as well as flammable liquids.

• DO NOT store explosives, such as aerosol cans, on or near the appliance.

• DO NOT use steel wool, oven cleaning pads, or any other materials that will scratch the surface.

• DO NOT attempt to disassemble or clean around any burner while another burner is on, otherwise an electric shock could result.

Page 9

ArtNo.270-0001

Proplus control to high

2. Cooker Overview

DocNo.020-0006 - Overview - 90DF - Prof+

Fig. 2.1

The 90 dual fuel cooker (Fig. 2.1) has the following features:

A. 5 hotplate burners including a wok burner B. A control panel C. A glide-out grill D. Programmable main fan oven E. Tall fan oven

Hotplate Burners

The drawing by each of the central knobs indicates which burner that knob controls.

Each burner has a Flame Supervision Device (FSD) that prevents the ow of gas if the ame goes out.

When the igniter button is pressed in, sparks will be made at every burner – this is normal. Do not attempt to disassemble or clean around any burner while another burner is on, otherwise an electric shock could result.

To light a burner, press the igniter button, and push in and turn the associated control knob to the high position as indicated by the large ame symbol (

The igniter should spark and light the gas. Keep holding the knob pressed in to let the gas through to the burner for about ten seconds.

), (Fig. 2.2).



Fig. 2.2

Page 10

Fig. 2.3

Fig. 2.4

Fig. 2.5

ArtNo.270-0003

Proplus control to low

ArtNo.311-0001 Right pans gas

If, when you let go of the control knob, the burner goes out, then the FSD has not been bypassed. Turn the control knob to the OFF position and wait for one minute before you try again, this time making sure to hold in the control knob for slightly longer.

Adjust the ame height to suit by turning the knob counterclockwise (Fig. 2.3). On this cooker the low position is beyond high, NOT between high and o.

If a burner ame goes out, turn o the control knob and leave it for one minute before relighting it.

Make sure that the ames are under the pans. Using a lid will help the contents boil more quickly (Fig. 2.4).

Large pans should be spaced well apart.

Pans and kettles with concave bases or down-turned base rims should not be used (Fig. 2.5).

Simmering aids, such as asbestos or mesh mats, are NOT recommended (Fig. 2.6). They will reduce burner performance and could damage the pan supports.

You should also avoid using unstable and misshapen pans that may tilt easily, and pans with a very small base diameter, e.g. milk pans, single egg poachers (Fig. 2.7).

Fig. 2.6

Fig. 2.7

ArtNo.311-0002 Pan with rim

Art No. 311-0003 Simmer aids

ArtNo.311-0004 T ipping wok

The minimum recommended pan diameter is 120 mm. The maximum allowable pan base diameter is 260 mm.

DO NOT use cooking vessels on the hotplate that overlap the edges.

Wok Burner

The wok burner is designed to provide even heat over a large area. It is ideal for large pans and stir-frying (Fig. 2.8).

For heating smaller pans, the aforementioned hotplate burners may be more ecient.

You should wipe the enamel top surface of the cooker around the hotplate burners as soon as possible after spills occur. Try to wipe them o while the enamel is still warm.

Note:

The use of aluminium pans may cause metallic marking of the pan supports. This does not aect the durability of the enamel and may be cleaned o with an appropriate metal cleaner.

Fig. 2.8

ArtNo.311-0005 Wok burner & pan support

Page 11

The Wok Cradle (optional)

The wok cradle is designed to t a 35 cm wok. If you use a dierent wok, make sure that it ts the cradle. Woks vary very widely in size and shape. It is important that the wok sits down on the pan support – however, if the wok is too small, the cradle will not support it properly (Fig. 2.9).

The cradle should be used on the wok burner only. When you t the cradle, check that it is properly located on the front and rear ngers and that the wok is supported properly on a pan support (Fig. 2.10).

The cradle will get very hot in use – allow plenty of time for it to cool before you pick it up.

The Griddle (optional)

The griddle ts the left-hand pan support, front to back (Fig.

2.11). It is designed for cooking food on directly. DO NOT use

pans of any kind on it. The griddle surface is non-stick and metal cooking utensils (e.g. spatulas) will damage the surface. Use heat resistant plastic or wooden utensils.

DO NOT put it crossways – it will not t properly and



will be unstable (Fig. 2.12).

Fig. 2.9

ArtNo.311-0006 Correct wok sizes

Fig. 2.10

ArtNo.311-0007 Wok stand close-up

Fig. 2.11

DO NOT put it on any other burner – it is not



designed to t in any of the other pan supports.

Position the griddle over the hotplate burners resting on the pan support. Check that it is securely located.

The griddle can be lightly brushed with cooking oil before use (Fig. 2.13). Light the hotplate burners. Adjust the ame heights to suit.

Preheat the griddle for a maximum of 5 minutes before adding food. Leaving it longer may cause damage. Turn the control knobs towards the low position, marked with the small ame symbol, to reduce the burner ames.

Always leave space around the griddle for the gases



to escape.

NEVER t two griddles side by side (Fig. 2.14).



After cooking, allow the griddle to cool before cleaning.

ArtNo.090-0002 90 Griddle position

ArtNo.090-0004 Incorrect griddle position

ArtNo.311-0009 Oil on griddle

Fig. 2.12

Fig. 2.13

Fig. 2.14

ArtNo.311-0008 Griddle positioning

Page 12

ArtNo.270-0004

Proplus grill control

Fig. 2.15

Fig. 2.16

ArtNo.330-0003 - Grill pan w handle pulled forwards

ArtNo.331-0001Grill pan pulled forwards

The Grill / Glide-out Grill

CAUTION: This appliance is for cooking purposes



only. It must not be used for other purposes, for example room heating.

CAUTION: Accessible parts may be hot when the grill



is in use. Young children should be kept away.

Open the door and pull the grill pan (Fig. 2.15) or carriage (Fig. 2.16) forward using the handle.

The grill has two elements that allow either the whole area of the pan to be heated or just the right-hand half.

Adjust the heat to suit by turning the knob. To heat the whole grill, turn the knob clockwise (Fig. 2.17).

To heat the right-hand half, turn the knob counter-clockwise. The neon indicator light by the grill control will come on.

For best results, leave the grill pan in the grill chamber and preheat the appropriate part(s) of the grill for two minutes. The grill trivet can be removed and the food placed on it while you are waiting for the grill to preheat.

Fig. 2.17

Fig. 2.18

ArtNo.331-0002 Grill pan high/low position

DO NOT leave the grill on for more than a few



moments, without the grill pan underneath it, otherwise the knobs may become hot.

Once the grill has preheated, take the grill pan out again and put the trivet back in place with the food on it. Slide the grill pan or carriage back into the grill chamber. Make sure that it is pushed right in.

The grill pan trivet can be turned over to give two grilling positions (Fig. 2.18).

Never close the grill door when the grill is on.



Page 13

The Ovens

The clock must be set to the time of day before the lefthand oven will work. See the following section on ‘The Clock’ for instructions on setting the time of day.

References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed from the front of the appliance.

ArtNo.270-0005 Proplus

electric oven control

Fig. 2.19

Both ovens are fan ovens that circulate hot air continuously, which means faster, more even cooking.

The recommended cooking temperatures for a fan oven are generally lower than a conventional oven.

Note: Please remember that all cookers vary so temperatures in your new ovens may dier to those in your previous cooker.

Operating the Ovens

Turn the oven knob to the desired temperature (Fig. 2.19).

The oven indicator light will glow until the oven has reached the temperature selected (Fig. 2.20). It will then cycle on and o during cooking.

100

ArtNo.270-0006 Proplus

oven control light

180

220

140

180

100

220

Fig. 2.20

Page 14

ArtNo.324-0010 Plate warming shelf

ArtNo.320-0013 Removing the shelf 3

ArtNo.320-0011 Removing the shelf 1

ArtNo.320-0012 Removing the shelf 2

Fig. 2.21

Front

Shelf guard

Fig. 2.22 Fig. 2.23

Accessories

Oven Shelves – Left-hand (Main) Oven

The oven shelves (Fig. 2.21) are retained when pulled forward but can be easily removed and retted.

Pull the shelf forward until the back of the shelf is stopped by the shelf stop bumps in the oven sides (Fig. 2.22).

Lift up the front of the shelf so the back of the shelf will pass under the shelf stop and then pull the shelf forward (Fig. 2.23).

To ret the shelf, line up the shelf with a groove in the oven side and push the shelf back until the ends hit the shelf stop. Lift up the front so the shelf ends clear the shelf stops, and then lower the front so that the shelf is level and push it fully back (Fig. 2.24).

Fig. 2.24 Fig. 2.25

ArtNo.324-0002 Oven shelf

Fig. 2.26

Fig. 2.28

Fig. 2.27

Fig. 2.29

Oven Shelves – Right-hand (Tall) Oven

The tall oven is supplied with four at cooking shelves (Fig. 2.25), and a plate-warming shelf (Fig. 2.26).

When using the tall oven, you can cook on all four shelves at the same time, but make sure that they are well spaced out to allow the hot air to circulate.

The Handyrack (Main Oven)

The Handyrack (Fig. 2.27) ts to the left-hand oven door only. Food cooking on it is easy to attend to, because it is accessible when the door is open.

The maximum weight that can be held by the Handyrack is 5.5 kg (12 lb). It should only be used with the supplied roasting tin, which is designed to t the Handyrack. Any other vessel could be unstable.

It can be tted at two dierent heights. One of the oven shelves must be removed and the other positioned to suit.

When the Handyrack is used in its highest position, other dishes can be cooked on the bottom shelf position or base of the oven.

When the Handyrack is used in its lowest position, other dishes can be cooked on the second shelf position or base of the oven.

ArtNo.320-0015

Fitting the Handyack 1

Fig. 2.30

ArtNo.320-0017 Main oven light

ArtNo.320-0016

To t the Handyrack, locate one side of it on the door bracket (Fig. 2.28).

Then spring the other side out to clip it onto the other bracket (Fig. 2.29).

Main Oven Light

Press the button to turn the light on (Fig. 2.30).

If the oven light fails, turn o the power supply before changing the bulb. See the ‘Troubleshooting’ section for details on how to change the bulb.

Page 15

3. The clock

The clock must be set to the time of day before the oven will work.

The 2-button clock

Setting the Clock

1. Once the cooker is connected and switched on, the display will start to ash.

2. To set the time, turn the Timer (A) knob to the Clock (C) setting and back to the Manual (D) position. The centre dot will ash indicating the time can be set. Turn the Adjusting (B) knob either clockwise or counterclockwise (Fig. 3.1) to set the time.

3. Once you have set the time, allow the centre dot to stop ashing, the time is now set.

Setting the minute minder

A Minute Minder (E) is a feature that can be set for a number of minutes and sounds an alarm once the specied amount of time has elapsed.

1. Turn the Timer (A) knob to the Minute Minder (E) setting – it should click into position (Fig. 3.2).

ArtNo.300-0005 2BC

minute minder setting

C D

A B

A – Timer knob, B – Adjusting knob

ArtNo.300-0005 2BC

minute minder setting

A B

Fig. 3.1

Fig. 3.2

Fig. 3.3

2. Turn the Adjusting (B) knob to set the amount of time required. Minimum time 1 minute (Fig. 3.3).

3. Turn the Timer (A) knob back to the Manual (D) setting to see the current time and the ‘Bell’ symbol on the display.

Cancel the timer alarm

Once the specied time has elapsed it will emit an alarm. There are two ways to cancel the alarm:

1. Turn the Adjusting (B) knob counter-clockwise or clockwise (Fig. 3.4).

2. Turn the Timer (A) knob to the Clock (C) or the Minute Minder (E) setting, and back to the Manual (D) mode, to return to normal cooking (Fig. 3.4).

NOTE

If the alarm is not manually switched o it will stop after

approximately 2 minutes.

When the Minute Minder is active the clock will not dim

between the hours of 10 pm and 6 am

A B

ArtNo.301-0007 2BC

Stopping the oven 1

A B

D E

Fig. 3.4

Page 16

Fig. 3.5

Fig. 3.6

Fig. 3.7

A B

ArtNo.311-0004 RShaw

2BC stoppingOven 1

To stop the oven at a speciﬁc time of day

You have set the required temperature and function mode and you would like the oven to automatically stop.

TOP TIP

Make a note of the current time so you do not forget.

1. Turn the Timer (A) knob to the Stop Time (G) setting. ‘AUTO’ will show in the display (Fig. 3.5).

2. Turn the Adjusting (B) knob to the amount of cooking time required. The display will show the current time plus the additional cooking time you have set (Fig. 3.6).

3. Turn the Timer (A) knob to the Auto (H) setting. The display will show the current time, the cooking symbol and the word ‘AUTO’ ( Fig. 3.7).

4. Once the specied time has elapsed it will emit an alarm and the oven will stop working. The cook pot symbol on the display will disappear and the word ‘AUTO’ will ash (Fig. 3.8).

Fig. 3.8

A B

5. When you return, turn the Timer (A) knob to the Manual (D) setting to return to manual cooking (Fig.

3.8).

TOP TIP

You can check how much time you have left, to the

programmed stop time, by turning Timer (A) from Auto (H)

to Stop Time (G) and back to Auto (H).

Page 17

A B

To start and stop the oven automatically

The timer allows you to automatically start and stop by a combination of the length of the cooking time and the stop time. Giving you the exibility to cook casseroles etc while you are out. You cannot set the actual start time.

1. Turn the Timer (A) knob to the Cook Time (F) setting. Turn the Adjusting (B) knob clockwise to set the length of the cooking time required (Fig. 3.9).

2. Turn the Timer (A) knob to the Stop Time (G) setting (Fig. 3.10). The display will show the current time of day plus the ‘cook time’ you just set.

Fig. 3.9

A B

Fig. 3.10

3. Turn the Adjusting (B) knob to set the time of day you want the oven to stop cooking (Fig. 3.11).

4. Set the oven to the required cooking temperature and

function mode.

5. Turn the Timer (A) knob to the Auto (H) setting (Fig. 3.12). If the display shows the current time and the word ‘AUTO’ the oven is set to turn on and o.

6. When the program starts the oven, the cooking symbol will appear on the display. Once the specied time has elapsed it will emit an alarm and the Multifunction Oven will stop working. The ‘Cooking’ symbol on the display will disappear and the word ‘AUTO’ will ash (Fig. 3.13).

7. Once the specied time has elapsed it will emit an alarm. There are two ways to cancel the alarm, refer to

“Cancel the timer alarm” on page 11

• The ‘cook period’, which is the length of time you want

the oven to cook for.

• The ‘stop time’, which is the time of day you want the oven to stop cooking.

Reset to manual cooking

A B

Fig. 3.11

Fig. 3.12

Fig. 3.13

To cancel any automatic settings turn the Timer (A) knob to the Manual (D) setting and release (Fig. 3.14).

NOTE: Whilst this operation cancels all automatic program settings, it does not cancel the minute minder.

Beeper tone adjustment

The beeper tone can be adjusted to three dierent levels.

Turn the Timer (A) knob to the Clock (C) setting. Turn the Adjusting (B) knob counter clockwise until the tone bars are displayed (Fig. 3.15).

To adjust the tone of the alarm, release the Adjusting (B) knob and then turn counter clockwise again (Fig. 3.16). The tone of the alarm will change. Repeat these steps until the desired alarm tone is set.

Fig. 3.15 Fig. 3.16

A B

Fig. 3.14

A B

Page 18

ArtNo.302-0002 - 6BC annotated

Fig. 3.17

The 6-button clock

You can use the timer (Fig. 3.17) to turn the oven(s) on and o. The clock must be set to the time of day before the oven(s) will work.

ArtNo.302-0002 - 6BC annotated

A B C D E F

A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time, D – Manual,

Symbol Function Notes

Minute Minder is active

]

[



[]

[AUTO]

[P]

[dot]

Oven(s) can be operated

automatic or automatic

mode has been enabled

Flashes during setting

E & F – Time setting buttons

Oven(s) are being

controlled in semi-

mode

Self clean (pyrolytic)

the time of day

If the ‘cook’ [

displayed the program has either:

ended and the oven(s) are nonoperational

the oven(s) are being controlled by an automatic program that has not started

Your cooker may not have this

pyrolytic function

] symbol is not



Table 3.1 describes the symbols shown on the digital display.

Setting the time of day

When the cooker is rst connected to the mains, or if there has been a prolonged power interruption, the clock display ashes [ 0.00 ] and [AUTO].

During the time setting process the centre dot will ash. When the process is complete the dot will stop ashing and the [] symbol will be displayed.

The time of day can be set in two ways:

• Press and hold the [] button. Now press the [+] or [-] buttons to increase or decrease the time (Fig. 3.18). Holding the [+] or [-] buttons for more than 2 seconds will advance / decrease the set time quickly. Release the buttons to set the time of day.

• Press and hold both the [] and [] buttons down (Fig. 3.19). Now press the [+] button (or [–] button) until the correct time shows.

DO NOT forget that it is a 24-hour clock.

If you need to reset the clock/cooker, turn o the power and wait several minutes, then start again.

Automatic dimming

Table 3.1

Fig. 3.18 Fig. 3.19

Fig. 3.20 Fig. 3.21

Fig. 3.22

Providing there are no automatic programs set, and the minute minder is not active, your clock will automatically dim during the hours between 22:00 and 06:00.

Minute minder

Press and hold the [

] button (Fig. 3.20), and then press the



[+] button (or [–] button) until the length of time you want to cook for is shown (Fig. 3.21).

You can check the time remaining by pressing [

]. When the



beeper sounds cancel it by pressing any button.

To reset the minute minder time; simultaneously press the [+] and [-] buttons.

NOTE: This will clear all automatic programs.

• The ‘cook period’, which is the length of time you want

the oven to cook for.

• The ‘stop time’, which is the time of day you want the oven to stop cooking.

Setting a cook duration

Press and hold the [

] button and set the required ‘cook



period’ by pressing the [+] button (or [–] button) (Fig. 3.22). The clock will now control the cook period of your oven(s). The [] symbol and [AUTO] will be displayed.

Once the ‘cook period’ is reached, the beeper sounds and the [AUTO] symbol ashes. Turn the oven control knob to 0 and

Page 19

ArtNo.302-0002 - 6BC annotated

then press any button to stop the beep. Press [] to return to

ArtNo.302-0002 - 6BC annotated

manual cooking.

Setting a cook end time

Fig. 3.23 Fig. 3.24

Press and hold the ‘stop time’ [

] button (Fig. 3.23) and then



press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig. 3.24). The [] symbol and [AUTO] will show in the display.

Once the ‘stop time’ is reached, the beeper sounds and the [AUTO] symbol ashes. Turn the oven control knob to 0 and then press any button to stop the beep. Press [

] to return to



manual cooking.

To start and stop the ovens automatically

Before you set the clock for automatic operation you must have two numbers clearly in mind – the ‘cook period’ and the ‘stop time’.

NOTE: You cannot set a start time directly – this is set automatically by setting the ‘cook period’ and the ‘stop time’.

Press and hold the [

] button (Fig. 3.25) and then press



the [+] button (or [–] button) until the required ‘cook period’ shows (Fig. 3.26).

Now press and hold the [

] button (Fig. 3.27) and then



press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig. 3.28). Release the buttons.

[AUTO] will now show in the display (Fig. 3.29).

Fig. 3.25 Fig. 3.26

Fig. 3.27 Fig. 3.28

Fig. 3.29

Fig. 3.30

Set the oven(s) to the required temperature. When cooking is nished [AUTO] will ash and the beeper will sound. Turn the oven knob(s) to the OFF position rst, and then press any button once to stop the beep; press the [

] button to return



to manual cooking.

If you are out, do not worry about the beeper going o, it stops after a while. When you return, turn the oven knob(s) to 0 rst, and then press [

] to return to manual cooking.



AUTO is showing, you want to reset to manual cooking

To return to manual cooking mode from an Automatic setting, simultaneously press the [+] and [-] key, this will clear the automatic program and return to manual mode.

Please note that this action will also clear the [Minute Minder] setting.

Beeper tone adjustment.

The beeper tone can be adjusted to three dierent levels.

Whilst in the time of day mode, press and hold the [-] button for a period until the display shows the Tone Bars (Fig. 3.30). Release the [-] button and immediately press again, this will adjust the tone down by a bar. Continue the process until a comfortable, tone is reached.

Please note, during a power reset the clock will remember the last tone set.

For an overview of the functions refer to Table 3.1.

ArtNo.302-0002 - 6BC annotated

Symbol Function Notes

[]

[]

[]

[ ]

[] &[]

[ ]

[ - ]

[ + ]

[ + ] & [ - ]

Sets the Minute Minder Used with the [+] and [-] buttons

Sets the duration / cook

period

Sets the end / stop cook

time

Allows the time of day to

be set when ‘AUTO’ is not

active

Resets the cooking control

to manual

Decreases time interval

Increases time interval

Clears all ‘AUTO’ and

minute minder programs

Used with the [+] and [-] buttons

Holding this button down

allows a quick set

Holding this button down

allows a quick set

Table 3.1

Page 20

4. Cooking tips

Tips on cooking with the timer

If you want to cook more than one dish, choose dishes that require approximately the same cooking time. However, dishes can be ‘slowed down’ slightly by using small containers and covering them with aluminium foil, or ‘speeded up’ slightly by cooking smaller quantities or placing them in larger containers.

Very perishable foods such as pork or sh should be avoided if a long delay period is planned, especially in hot weather.

DO NOT place warm food in the oven to be timed.



DO NOT use a timed oven that is already warm.



DO NOT use the timed oven if the adjoining oven is



already warm.

Whole poultry must be thoroughly defrosted before being placed in the oven. Check that meat and poultry are fully cooked before serving.

General oven tips

The wire shelves should always be pushed rmly to the back of the oven.

Baking trays with food cooking on them should be placed level with the front edge of the oven’s wire shelves. Other containers should be placed centrally. Keep all trays and containers away from the back of the oven, as overbrowning of the food may occur.

For even browning, the maximum recommended size of a baking tray are:

• depth: 340 mm (13 ⁄”) by width: 340 mm (13 ⁄”) in the main oven

• depth: 321 mm (12 ⁄”) by width: 232 mm (9 ⁄”) in the tall oven.

When the oven is on, DO NOT leave the door open for longer than necessary, otherwise the knobs may get very hot.

• Always leave a “finger’s width” between dishes on the same shelf. This allows the heat to circulate freely around them.

• To reduce fat splashing when you add vegetables to hot fat around a roast, dry them thoroughly or brush lightly with cooking oil.

• Where dishes may boil and spill over during cooking, place them on a baking tray.

• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your Cooker’) work better when fat splashes are avoided. Cover meat when cooking with foil or use a roasting bag.

• Sufficient heat rises out of the oven while cooking to warm plates in the grill compartment.

• If you want to brown the base of a pastry dish, preheat the baking tray for 15 minutes before placing the dish in the centre of the tray.

Page 21

5. Cooking table

DocNo.031-0004 - Cooking table - electric & fan single cavity

The oven control settings and cooking times given in the table below are intended to be used AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a preferred result.

Food is cooked at lower temperature in a fan oven than in a conventional oven. When using recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The temperature in the fan oven does not vary with height in the oven so you can use any shelf.

Conventional Oven

Food Meat

Beef (no bone)

Lamb

Pork

Poultry

Chicken

Turkey

Duck

Casserole Yorkshire Pudding Cake

Very rich fruit - Christmas, wedding, etc. Fruit 180 mm tin Fruit 230 mm tin Madeira 180 mm Small cakes Scones Victoria sandwich 180 mm tin 210 mm tin

Desserts

Shortcrust tarts Fruit pies Tartlets Puff pastry Meringues Baked egg custard Baked sponge pudding Milk pudding

Bread Fish

Fillet Whole Steak

Temperature °C (Shelf Position)

160 (C)

200 (C) 160 (C) 200 (C) 160 (C) 200 (C)

160 (C) 200 (C) 160 (C) 200 (C) 160 (C) 200 (C)

140-150 (C)

220 (C)

140 (C/B)

150 (C/B) 150 (C/B) 160 (C/B) 170 (C/B) 200 (C/B)

170 (C/B) 170 (C/B)

200 (C/B) 180 (C/B) 180 (C/B) 210 (C/B) 100 (C/B) 160 (C/B) 180 (C/B)

140-150 (C/B)

210 (C)

Fanned Grilling

190 (C/B) 190 (C/B) 190 (C/B)

Fan Oven

Temperature

°C

150 190 150 190 150 190

130-140

210

130

140 140 150 160 190

160 160

190 170 170 200

90 150 170

130-140

200

190 (C/B) 190 (C/B) 190 (C/B)

Approximate Cooking Time

ArtNo.050-0001 Gas cooking table

30-35 minutes per 500g +30-35 minutes. 20-25 minutes per 500g +20-25 minutes. 30-35 minutes per 500g +30-35 minutes. 25-30 minutes per 500g +25-30 minutes. 35-40 minutes per 500g +35-40 minutes. 25-30 minutes per 500g +25-30 minutes.

20-25 minutes per 500g +20-25 minutes. 15-20 minutes per 500g +15-20 minutes. 20 minutes per 500g +20 minutes. 15 minutes per 500g +15 minutes. 25-30 minutes per 500g. 20 minutes per 500g. 2-4 hours according to recipe. Large tins 30-35 minutes; individual 10-20 minutes.

45-50 minutes per 500g of mixture.

2-2½ hours. Up to 3½ hours. 80-90 minutes. 15-25 minutes. 10-15 minutes.

20-30 minutes. 30-40 minutes.

20-30 minutes on a preheated tray. 35-45 minutes. 10-20 minutes according to size. 20-40 minutes according to size. 2-3 hours. 45-60 minutes. 40-45 minutes. 2 to 3 hours. 20-30 minutes.

15-20 minutes. 15-20 minutes per 500g. Steaks according to thickness.

Top (T)

Centre (C)

Base (B)

Thoroughly thaw frozen joints before cooking. Meat may be roasted at 220°C (210°C for fan oven) and the cooking time adjusted accordingly. For stuffed and rolled meats, add approximately 10 minutes per 500g, or cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for the remainder.

For stuffed poultry, you could cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for remainder. Do not forget to include the weight of the stuffing. For fresh or frozen prepacked poultry, follow instructions on the pack. Thoroughly thaw frozen poultry before cooking.

Using the conventional oven: when two tier cooking leave at least one runner space between shelves. Position the baking tray with the front edge along the front of the oven shelf.

Up to three tiers can be cooked in a fan oven at the same time but make sure to leave at least one runner space between each shelf being cooked on.

Using the conventional oven: for even browning the maximum size of baking tray recommended is 340 mm x 340 mm. This ensures free heat circulation. If cooking a two tier load, the trays should be interchanged approximately halfway though the cooking time.

ArtNo.050-0007

Oven shelf positions

Oven Shelf Positions

Page 22

5. Cleaning Your Cooker

ArtNo.045-0004 - Cleaning - 90 induction - tpl glzd dr & GO grill

Fig. 5.1

ArtNo.311-0032 Burner layout FSD

A – Cap, B – Head, C – Notch, D – Base, E – Electrode

ArtNo.311-0033 Wok burner details FSD

Essential Information

Isolate the electricity supply before carrying out any thorough cleaning. Allow the cooker to cool.

NEVER use paint solvents, washing soda, caustic



cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt.

DO NOT mix dierent cleaning products – they may



react together with hazardous results.

All parts of the cooker can be cleaned with hot soapy water – but take care that no surplus water seeps into the

appliance.

Remember to switch on the electricity supply and reset the clock before re-using the cooker.

Hotplate Burners

The burner heads and caps can be removed for cleaning.

DO NOT put the burner heads in a dishwasher.



Make sure they are absolutely dry before replacing them.

The Single Ring Burners

When retting the burner head, make sure that the notch lines up with the electrode or hole in the base. Check that the burner head is level and that the cap is tted centrally on the burner head (“Fig. 5.1”).

A – Inner burner cap, B – Outer burner cap, C – Inner burner head,

D – Outer burner head, E – Wok burner base

Fig. 5.1

The Wok Burner

The wok burner can also be taken apart for cleaning.

When reassembling the wok burner (“Fig. 5.1”), turn over the large base ring and nd the ‘D’ shaped area (“Fig. 5.1”). Turn the head until the ‘D’ matches the one on the burner base. Flip the burner over once again and place it on the burner base.

To t the small inner burner, nd the larger electrode notch in the burner rim. Line this up with the white ignition electrode and place the inner burner on the large base ring (“Fig. 5.1”).

Now t the two burner caps, making sure that they are seated properly.

Check the burner ports are not blocked. If a blockage occurs, remove stubborn particles using a piece of fuse wire.

The Wok Cradle

Recommended cleaning materials are hot soapy water, a moistened soap pad, cream cleaner or a nylon scourer.

A – Electrode notch, B – Ignition electrode

Page 23

Grills

The grill pan and trivet should be washed in hot soapy water. Alternatively, the grill pan can be washed in a dishwasher.

After grilling meats or any foods that soil, leave to soak for a few minutes immediately after use. Stubborn particles may be removed from the trivet using a nylon brush.

Before you remove any of the grill parts for cleaning, make sure that they are cool, or use oven gloves.

Cleaning the Glide-out Grill

The grill pan can be easily removed for cleaning as follows:

Remove the grill pan support frame by pulling the grill pan forward (“Fig. 5.1”).

Fig. 5.1

ArtNo.331-0003 Grill frame out, no pan

Lift the grill pan clear of the support frame. is held to the side rails by two clips on each side (“Fig. 5.1”).

For each side, support the side rail with one hand and with the other hand lift the frame up and out of the side clips (“Fig. 5.1”).

For safety, push the side rails back into the grill chamber.

If you need to remove the side rails to allow cleaning of the grill chamber, you can unhook them from the grill chamber sides (“Fig. 5.1”) and wipe the sides clean with a soft cloth and mild detergent.

DO NOT put the side runners in a dishwasher.



Once you have nished, hook the side rails back onto the sides of the chamber. To ret the frame, pull the side rails forward and, for each side in turn, support the side rail and press the frame down into the side rails. Replace the grill pan. When retting the grill pan, make sure that the wide rim is at the front (“Fig. 5.1”).

The support frame

Control Panel and Doors

Avoid using any abrasive cleaners, including cream cleaners. For best results, use a liquid detergent.

The same cleaner can also be used on the doors, or alternatively, using a soft cloth wrung out in clean hot soapy water. You can use the same method for cleaning the control panel and knobs.

Fig. 5.1

ArtNo.331-0004 Removing the grill frame

Fig. 5.1

After cleaning, polish with a dry cloth.

ArtNo.331-0005 Removing the grill rail

Fig. 5.1

ArtNo.331-0006 Grill pan plan

Page 24

ArtNo.320-0002a Proplus oven door side screws

Fig. 5.1

Glass Fronted Door Panels

The oven door front panels can be taken o so that the glass panels can be cleaned. Move the cooker forward to gain access to the sides (see the ‘Moving the Cooker’ section under ‘Installation’).

Open the oven door slightly and remove the front panel xing screws from the door sides, two each side (“Fig. 5.1”).

Carefully lift o the outer door panel. The inside face of the glass panels can now be cleaned – take care not to disturb or wet the door insulation.

Note: If the door is triple glazed then the inner two panels are xed together and should not be separated. After cleaning, carefully ret the outer door panel and replace the side xing screws.

DO NOT use harsh abrasive cleaners or sharp metal



scrapers to clean the oven door glass since they can

scratch the surface, which may result in shattering of the glass.

Ovens

'Cook & Clean' Panels

The main oven has side ‘Cook & Clean’ panels which have been coated with a special enamel that partly cleans itself. This does not stop all marks on the lining, but helps to reduce the amount of manual cleaning needed.

These panels work better above 200 °C. If you do most of your cooking below this temperature, occasionally remove the panels and wipe with a lint free cloth and hot soapy water. The panels should then be dried and replaced and the oven heated at 200 °C for about one hour. This will make sure that the panels are working eectively.

Removing the Panels to Clean the Enamel Interior

Some of the lining panels can be removed for cleaning.

If you wish to clean the enamel interior of the oven, you will need to remove the shelves before removing the ‘Cook & Clean’ panels. You do not have to remove the support brackets to remove the panels. Lift each panel upward and slide forward o the support brackets (“Fig. 5.1”).

Once the panels have been removed, the oven enamel interior can be cleaned.

DO NOT use steel wool, oven cleaning pads, or any other materials that will scratch the surface.

Ret in the reverse order.

The Tall Oven

To clean the oven sides, slide out the shelves and with both hands gently pull the side supports away (“Fig. 5.1”).

Page 25

Cleaning Table

Cleaners listed (Table 5-1) are available from supermarkets or electrical retailers as stated.

For enamelled surfaces use a cleaner that is approved for use on vitreous enamel.

Regular cleaning is recommended. For easier cleaning, wipe up any spillages immediately.

Hotplate

Part Finish Recommended Cleaning Method

Hob top (including burner heads and caps)

Ceramic/induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.

Griddle plate (some models only) Non-stick surface

Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Outside of Cooker

Part Finish Recommended Cleaning Method

Door, door surround and storage drawer exterior

Sides and plinth Painted surface Hot soapy water, soft cloth.

Enamel, stainless steel, aluminium

Enamel or paint

Stainless steel

Hot soapy water, soft cloth. Any stubborn stains remove gently with a nylon scourer.

Allow to cool. Wash in hot soapy water. Do not use abrasive cleaners/scourers. Dishwasher.

Hot soapy water, soft cloth. Any stubborn stains, remove gently with a liquid detergent.

E-cloth (electrical retailers) or microbre all-purpose cloth

(supermarket).

Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.

Control panel

Control knobs/handles & trims

Oven door glass/glass lid (some models only)

Paint, enamel, stainless steel, glass Plastic/chrome, copper or lacquered brass

Brass Brass polish.

Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Warm soapy water. Do not use proprietary cleaners other than washing-up liquid, as this may cause cosmetic damage.

Warm soapy water, soft cloth.

Oven and Grill

Part Finish Recommended Cleaning Method

Sides, oor & roof of oven NOT ‘COOK & CLEAN’ OVEN PANELS (see below)

‘Cook & Clean’ oven panels (some models only)

Oven shelves, Handyrack, grill trivet, Handygrill rack (some models only)

Grill pan/meat tin (some models only)

Enamel

Special enamel that partly cleans itself

Chrome

Enamel Hot soapy water. Soap lled pad. Dishwasher.

Any proprietary oven cleaner that is suitable for enamel. CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW

MANUFACTURER’S INSTRUCTIONS. Do not allow contact with the oven elements.

This surface cleans itself at 200 °C and above, or the panels can be removed and washed with hot soapy water and a nylon brush.

An oven interior cleaner that is suitable for chrome. Soap lled pad. Dishwasher.

Table 5-1

Page 26

6. Troubleshooting

Hotplate ignition or hotplate burners faulty

Is the power on? Is the clock illuminated?

If not, there maybe something wrong with the power supply.

Are the sparker (ignition electrode) or burner slots blocked by debris?

Are the burner trim and caps correctly located? See the section on ‘Cleaning’.

Hotplate burners will not light

Make sure that the burner parts have been replaced correctly after wiping or removing for cleaning.

Check that there is not a problem with your gas supply. You can do this by making sure that other gas appliances you may have are working.

Do the burners spark when you push the button?

If not, verify that the power is on by checking that the clock is illuminated.

Steam is coming from the oven

When cooking foods with high water content (e.g. oven fries) there may be some steam visible at the rear grille.

Power failure

In the event of a failure in the electrical supply, remember to reset the clock to make sure that the timed oven continues to operate.

Food is cooking too slowly, too quickly, or burning

Cooking times may dier from your previous oven.

Check that you are using the recommended temperatures and shelf positions – see the oven cooking guide. The oven control settings and cooking times are intended to be used only as a guide.

Individual tastes may require the temperature to be altered either way, to get the results you want.

The oven is not cooking evenly

Do not use a baking tray with dimensions larger than those specied in the section on ‘General Oven Tips’.

If you are cooking a large item, be prepared to turn it round during cooking.

If two shelves are used, check that space has been left for the heat to circulate. When a baking tray is put into the oven, make sure that it is placed centrally on the shelf.

Take care when opening the oven door, as there may be a momentary pu of steam when the oven door is opened. Stand well back and allow any steam to disperse.

What cleaning materials are recommended for the cooker?

See the ‘Cleaning’ section for recommended cleaning materials.

Never use caustic or abrasive cleaners as these will



damage the surface.

An oven fan is noisy

The note of the oven fan may change as the oven heats up – this is perfectly normal.

The knobs get hot when I use the oven or the grill. Can I avoid this?

Yes, this is caused by heat rising from the oven or the grill, and heating them up. Do not leave the oven door open.

Make sure that the grill pan is pushed right back to the ‘back stop’ when grilling.

Always grill with the grill compartment door open.

Check that the door seal is not damaged and that the door catch is adjusted so that the door is held rmly against the seal.

A dish of water when placed on the shelf should be the same depth all over. (For example, if it is deeper at the back, then the back of the cooker should be raised up or the front lowered.) If the cooker is not level arrange for your supplier to level it for you.

Oven not coming on

Is the power on? Is the clock illuminated? If not, there may be something wrong with the power supply.

Is the cooker supply on at the isolator switch?

Has the time of day been set? Is the key symbol [ ] showing in the display to signify

that the oven is locked? See the ‘Clock’ section of the instructions for more information on the key lock feature.

The timed oven is not coming on when automatic cooking

Has the oven knob been left in the OFF position by mistake?

Is the oven locked (see above)?

If there is an installation problem and I don’t get my original installer to come back to x it who pays?

You do. Service organizations will charge for their call outs if they are correcting work carried out by your original installer. It is in your interest to track down your original installer.

Oven temperature getting hotter as the cooker gets older

If turning the temperature down using the oven control knob has not worked, or has only worked for a short time, then you may need a new thermostat. This should be tted by a service person.

Page 27

An oven light is not working

The bulb has probably burnt out. You can buy a replacement bulb (which is not covered under the warranty) from a good electrical shop. Ask for a 15 W – 230 V lamp, FOR OVENS. It must be a special bulb, heat resistant to 300 °C (Fig. 6.1).

Turn o the power at the circuit breaker.

Before removing the existing bulb, turn o the power supply and make sure that the oven is cool. Open the oven door and remove the oven shelves.

Unscrew the bulb cover by turning counter-clockwise. It may be very sti (Fig. 6.2).

Taking care to protect your ngers with a glove in case the bulb should shatter, unscrew the old bulb.

Screw in the new bulb; screw back the bulb cover. Turn on the circuit breaker and check that the bulb now lights.

The oven door is misaligned

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig. 6.3). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig. 6.4).

Fig. 6.1

ArtNo.324-0005 Oven light bulb

Fig. 6.2

Fig. 6.3

Retighten the hinge screws.

Eect of hinge adjustment – exaggerated for clarity

Centre line of hinge pin

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

Fig. 6.4

Page 28

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

7. Installation

Service and Spares

Firstly, please complete the appliance details below and keep them safe for future reference – this information will enable us to accurately identify the particular appliance and help us to help you. Filling this in now will save time and inconvenience if you later have a problem with the appliance. It may also be of benet to keep your purchase receipt with this leaet. You may be required to produce the receipt to validate a warranty eld visit.

Distributor’s Name and Address Andi-Co Australia Pty Ltd.

1 Stamford Road, Oakleigh, VIC 3166

Customer Care Tel: 1300 650 020 Email: service@andico.com.au

Name of Appliance

Appliance Serial Number*

Fuel Type Dual Fuel

Date of Purchase

Installer’s Name, Address and Telephone No.

Date of Installation

* This information is on the appliance data badge.

If You Have a Problem

In the unlikely event that you have a problem with your appliance, please refer to rest of this booklet, especially the problem solving section, rst to check that you are using the appliance correctly.

If you are still having diculty, contact Customer Care on 1300 650 020 or email service@andico.com.au.

Please Note

For warranty information and how to request a remedy, please refer to the warranty document provided with the appliance or contact Customer Care.

Out of Warranty

We recommend that our appliances are serviced regularly throughout their life to maintain the best performance and eciency. The frequency of service will depend on usage – for normal usage once a year should suce.

Service work should only be carried out by a suitably Authorised Person.

Spare Parts

To maintain optimum and safe performance, we recommend that only genuine spare parts are used. Do not use reconditioned or unauthorised controls. Contact Spare Parts on (03) 9569 7744 or email spares@andico.com.au

Page 29

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Safety Requirements and Regulations

Please read the Before you start... chapter, before



you begin any installation and maintenance work on this appliance.

You must be aware of the following safety requirements & regulations.

Before installation, make sure that the local



distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible.

The appliance must be installed in accordance with



the regulations in force and only in a well ventilated space.

Read the instructions before installing or using this



appliance.

The regulations and standards are as follows:

• AS/NZS 5601 – ‘Gas Installations’

• AS/NZS 3000 - ‘Wiring Rules’

In your own interest and that of safety, it is law that all gas appliances be installed by competent persons.

Failure to install the appliance correctly could



invalidate any warranty or liability claims and lead to prosecution.

The cooker must be installed in accordance with all local gas tting regulations, municipal building codes, electrical wiring regulations and any other relevant statutory regulations.

Provision of Ventilation

This appliance is not connected to a combustion products evacuation device. Particular attention shall be given to the relevant requirements regarding ventilation.

The room containing the cooker should have an adequate air supply.

Install the cooker in a location to allow the complete combustion of gas, proper ueing and to maintain ambient temperature of the immediate surroundings at safe limits, under normal condition.

Location of Cooker

The cooker may be installed in a kitchen/kitchen diner but NOT in a room containing a bath or shower.

Note: An appliance for use on Propane must not be installed in a room or internal space below ground level, e.g. in a basement.

Conversion

All models are supplied set for use on Natural gas. A conversion kit for Propane gas is included with the appliance. See the instructions that are supplied with the conversion kit.

After converting the appliance, please attach the Gas Conversion sticker over the appropriate area of the data badge – this will identify the gas type for which the appliance is now set.

WARNING!



Where this appliance is installed in a marine craft, caravan or mobile home, it shall NOT be used as a space heater.

Page 30

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

You will need the following equipment to complete the cooker installation satisfactorily:

• Flexible gas hose.

• Gas pressure tester/manometer.

• Multimeter: For electrical checks.

You will also need the following tools:

1. Electric drill

2. Masonry drill bit (only required if tting the cooker on a

stone or concrete oor)

3. Wall plugs (only required if tting the cooker on a stone or concrete oor)

4. Steel tape measure

5. Cross head screwdriver

6. Flat head screwdriver

7. 4 mm & 3 mm Allen keys

8. Spirit level

9. Pencil

10. Adjustable spanner

11. 13 mm spanner or socket wrench

12. Screws for tting the restraining chain and bracket

Checking the Parts:

3 pan supports Plinth (1-piece model shown)

ArtNo.000-0001 90 Pan supports

Griddle (optional)

2 at shelves Handyrack

ArtNo.350-0005 - 90 plinth

Grill pan & trivet (glide-out model

shown)

ArtNo.330-0001 - Grill pan

ArtNo.173-0008 - Oven - Handyrack

Roasting tin Tall oven shelves & shelf supports

ArtNo.324-0004 Roasting tin

ArtNo.000-0010 Tall oven shelves

Restraining chain & hook Stability bracket

ArtNo.020-0021 - Restraining chain & hook

Page 31

INSTALLATION

ArtNo.091-0004 - 90DF - cooker clearances (AUS)

ArtNo.000-0035 90 Prof+ DF Clearances #3

130 mm min

Check the appliance is electrically safe and gas sound when you have nished.

Positioning the Cooker

The diagram (Fig. 7.1) shows the minimum recommended distance from the cooker to nearby surfaces as given in AS/NZS 5601.

Where the appliance is installed next to cabinetry, the cabinet material must be capable of withstanding 70°C. If this appliance is installed near vinyl wrapped surfaces, use an installation kit available from the vinyl-wrap supplier. Falcon cannot accept any responsibility for damage caused due to installation into cabinets with low temperature tolerances.

*Any splashback must be tted in accordance with the manufacturers instructions. Allowance should be made for the additional height of the ue trim, which is tted to the cooker hob.

1. Overhead – Measurement A

The minimum height of any surface above the cooker is 650 mm above the hotplate.

Cookerhoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a cookerhood be less than 650 mm or, for an overhead exhaust fan, 750 mm.

Fig. 7.1

Fig. 7.2

2. Side Clearances – Measurements B & C

Where B, measured from the periphery of the nearest burner to any vertical combustible surface, or vertical combustible surface covered with toughened glass or sheet metal, is less than 200 mm, the surface shall be protected to make sure that the combustible surface does not exceed 65 °C above ambient*. Even with the surface protected, the dimension B should not be less than 135 mm above hotplate level.

*The xing of 5 mm thick ceramic tiles to the surface, or attaching re resistant material to the surface and covering with sheet metal with a minimum thickness of 0.4 mm to a height C of not less than 150 mm above the hotplate, should satisfy this requirement.

3. Side Clearances – Measurement D & E

Where D, the distance from the periphery of the nearest burner to a horizontal combustible surface is less than 200 mm, then E shall be 10 mm or more, or the horizontal surface shall be above the trivet.

If the cooker is near a corner of the kitchen, a clearance of 130 mm is required to allow the oven doors to open (Fig. 7.2). The actual opening of the doors is slightly less, but this allows for some protection of your hand as you open the door.

Fig. 7.3

We recommend a gap of 910 mm between units to allow for moving the cooker. Do not box the cooker in – it must still be possible to move the cooker in and out for cleaning and servicing.

Page 32

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Fig. 7.4

Fig. 7.5

Fig. 7.6

ArtNo.010-0004 Moving the cooker

Moving the Cooker

On no account try and move the cooker while it is



plugged into the electricity supply.

The cooker is very heavy, so take great care.



We recommend two people manoeuvre the cooker. Make sure that the oor covering is rmly xed, or removed to prevent it being disturbed when moving the cooker around. To help you, there are two levelling rollers at the back and two screw-down levelling feet at the front.

From the back tilt the cooker forward and remove the rear half of the polystyrene base pack (Fig. 7.3). Repeat from the front and remove the front half of the polystyrene base.

Lowering the Two Rear Rollers

To lower the rear rollers, rst t a 13 mm spanner or socket wrench onto the hexagonal adjusting nut at the front of the cooker (Fig. 7.4). Rotate the nut – clockwise to raise – counter-clockwise to lower.

Make 10 complete (360°) turns clockwise. Make sure you lower BOTH REAR ROLLERS.

Completing the Move

Unfold the rear edge of the cardboard base tray. Open the grill door and right-hand oven door so that you can get a good grip on the bottom of the fascia panel as you move the oven (Fig. 7.5).

Fig. 7.7

Fig. 7.8

Stability bracket

ArtNo.070-0014 - Stability bracket - Wall fitting

Outer stability

bracket

Wall

3 mm min

Typical oor mounting

3 mm min

Typical wall mounting

Cooker

Floor

Carefully push the cooker backwards o the cardboard base. Remove the base tray.

Position the cooker close to its nal position, leaving just enough space to get behind it (Fig. 7.6).

DO NOT use the door handles or control knobs to



manoeuvre the cooker.

Levelling the Cooker

It is recommended that you use a spirit level on a shelf in one of the ovens to check for level.

Place the cooker in its intended position. Take care not to twist it within the gap between the kitchen units as damage may occur to the cooker or units.

The front feet and rear rollers can be adjusted to level the cooker. To adjust the height of the rear of the cooker use a 13 mm spanner or socket wrench to turn the hexagonal adjusting nuts at the front bottom corners of the cooker.

To set the front turn the feet bases to raise or lower.

Fitting the Stability Bracket and Chain

A stability bracket and chain MUST be tted when



the cooker is connected to a exible gas supply.

Unless properly installed, the cooker could be tipped by leaning on the door. Injury might result from spilled hot liquids or from the cooker itself.

IMPORTANT: The cooker must be set to the correct height and levelled before the stability bracket is installed.

Page 33

INSTALLATION

ArtAUS.141-0007 - Gas connections - 90 Elan

300

100

240

100

All dimensions in millimetres

Gas inlet

Check the appliance is electrically safe and gas sound when you have nished.

Fitting a Stability Bracket

When tting a stability bracket please refer to the instructions supplied with the bracket for further details on tting.

When tting a stability bracket (Fig. 7.7 and Fig. 7.8) adjust the bracket to give the smallest practicable clearance between the bracket and the engagement slot in the rear of the cooker. Fit the bracket so that it engages as far as possible over the chassis of the cooker.

Fitting the Restraining Chain

The restraining chain MUST be tted.

The length of chain between the appliance and the wall xing should prevent strain on the gas and electricity connections, but still allow access to unhook the chain when the cooker is pull forward.

Measure the length of chain required. Use the clamp supplied to clamp onto the gas pipe (Fig. 7.9). Fix the supplied hook securely to the wall.

Gas Connection

Must be in accordance with the relevant standards.

The gas supply needs to terminate with a threaded tting ½”. The inlet connector is located just below the hotplate level at the rear of the cooker.

Fig. 7.9

Restraining

chain

ArtNo.011-0007 - Restraining chain (AUS)

Fig. 7.10

Because the height of the cooker can be adjusted and each connection is dierent it is dicult to give precise dimensions. Ideally, the house supply connection should be in the shaded area (Fig. 7.10).

Means of isolation must be provided at the supply point by either an approved quick-connect device or a Type 1 manual shut-o valve.

The hose should be tted so that both inlet and outlet connections are vertical so that the hose hangs downwards in a ‘U’ shape (Fig. 7.10).

A exible connection is supplied with the cooker. If it is necessary to use another hose it must be to AS 1869 Class B and be suitable for your gas type.

If in doubt contact your supplier. Screw connect the threaded end of the hose into the gas inlet.

After completing the gas connection, check the cooker is gas sound with a pressure test. When checking for gas leaks do not use washing up liquid – this can corrode. Use a product specically manufactured for leak detection.

Natural Gas

The adjustable spring loaded gas pressure regulator is preset to give a nominal pressure of 1 kPa on Natural gas. Connect to the Rp½ inlet on the underside of the pressure regulator.

Propane

This cooker is supplied ready for use on Natural gas. A conversion kit for Propane gas is supplied with the cooker – see the ‘Conversion to Propane Gas’ section.

Page 34

INSTALLATION

ArtNo.132-0002 - 3 phase 240/415Vac 50Hz

3-phase 400 VAC 50 Hz

Check the appliance is electrically safe and gas sound when you have nished.

Fig. 7.11

Fig. 7.12

ArtNo.132-0001 - 1 phase 240Vac 50Hz

1-phase 220-240 VAC 50 Hz

Pressure Testing

The pressure test point is accessible on the inlet pipe at the rear. Remove the test nipple screw and t a pressure gauge to the test point. Turn on and light two of the hotplate burners.

For Natural Gas cookers the pressure should be between

0.95kPa and 1.0kPa.

For Propane X cookers the pressure should be 2.54 kPa.

Electrical Connection

This appliance must be installed by a qualied electrician to comply with with current AS/NZS 3000 Wiring Rules and regulations in force.

Make sure that the mains characteristics (voltage, nominal, power, etc.) match the ratings indicated on the cooker data plate.

Current Operated Earth Leakage Breakers

The combined use of your cooker and other domestic

appliances may cause nuisance tripping, so we

recommend that the cooker is protected on an individual

RCD (Residual Current Device) or RCBO (Residual Current

Breaker with Overload).

IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED

ELECTRICIAN.

Fig. 7.13

Fig. 7.14

3-phase 230 V 50 Hz

Mains terminal

A N

Fixing bracket for

conduit connection

Cable clamp

ArtNo.132-0005 - Fixed wiring connection 2 (AUS)

The cooker is preset for a single-phase earthed electrical connection. It is essential to install a multi-pole circuit breaker that completely disconnects the appliance from the mains, with a minimum contact break distance of 3 mm.

WARNING: THIS APPLIANCE MUST BE EARTHED.



The appliance must be connected to an ecient earthing circuit. If the electricity network is not equipped with an earth connection, then it must be installed separately in compliance with local regulations.

Earthing is a safety measure required by law, and must be performed with particular care by a qualied technician, who must also check that the electricity supply characteristics are correct.

The total electrical load of the appliance is approximately

7.4 kW. The cable size used should be suitable for this load and comply with all local requirements (i.e. PVC Insulated cable IEC 60227 – code 53 for ordinary cables).

Please note the maximum cable sizes are 6 mm² for the screw terminals and 10 mm² for the 3-pronged links.

Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type (Fig. 7.11 and Fig. 7.12). correctly tted and that the terminal screws are tight. Secure the mains cable using the cable clamp.

Check that the links are

Conduit

An isolation switch shall be provided and mounted near the cooker, in a readily accessible position, in compliance with AS/NZS 3000 and/or AS/NZS 5601 as applicable for the appliance conguration.

Page 35

INSTALLATION

ArtNo.000-0006 - Securing the 110 plinth

ArtNo.350-0011 - Fitting the plinth 2 (Kitchener)

Outer plinth

Outer plinth xing screw

Inner plinth

Check the appliance is electrically safe and gas sound when you have nished.

Fixed Wiring

For connection to xed wiring, i.e. exible conduit, remove the electrical terminal cover box on the back panel. Using the two screws, x the strain relief bracket in position.

Fix the conduit-to-conduit mounting bracket onto the strain relief bracket. Connect the mains cable to the correct terminals for your electrical supply type (Fig. 7.13 and Fig. 7.14). Check that the links are correctly tted and that the terminal screws are tight.

Replace the electric terminal cover box; make sure that the conduit is clear of the bottom ange.

Final Checks

Note: The clock must be set before the ovens will work. See ‘The Clock’ section for instructions on setting the time of day.

Hotplate Check

Check each burner in turn. There is a Flame Supervision Device (FSD) that stops the ow of gas to the burner if the ame goes out. For each burner, turn the control knob to the solid ame symbol. Press in the control knob. This lets gas through to the burner. Keep holding the knob pressed in and press the igniter button or light with a match. Keep holding the control knob pressed in for about 10 seconds.

Fig. 7.15

Fig. 7.16

ArtNo.350-0010 - Fitting the plinth 1 (Kitchener)

Fig. 7.17

If, when you let go of the control knob the burner goes out, the safety device has not held in. Wait one minute then try again this time holding the control pressed in for slightly longer.

Grill Check

Open the grill compartment door. Turn on the grill control and check that the grill heats up.

Oven Check

Turn on the oven and check that it starts to heat up. Check that the oven lights are working.

Note: The oven light bulb is not included in the guarantee.

Final Fitting

Fitting the 1-piece Plinth (Professional+)

Remove the 3 screws for the plinth mounts along the front bottom edge of the cooker (Fig. 7.15). Fasten the plinth using these screws (alternative colour screws can be found in the loose parts pack).

Fiting the 2-piece Plinth (Kitchener)

Fit the inner plinth to the bottom front of the cooker using the 4 screws provided (Fig. 7.16).

Fit the outer plinth (2 screws, 1 each end) to the inner plinth (Fig. 7.17). Adjust the height of the outer plinth by sliding it up or down via the slotted hole.

Customer Care

Installer: Please complete your details in this guide, inform the user how to operate the cooker and hand over the instructions.

Thank you.

Page 36

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

8. Conversion to Propane Gas

Fig. 8.1

Fig. 8.2

ArtNo.311-0010 Injectors

A – Jet, B – Internal injector, C – External injector

Conversion from Natural Gas (1.0 kPa) to LPG X Propane (2.54 kPa)

This conversion must be performed by a competent



person, in accordance with these instructions and with the local supply company requirements. Read the instructions before converting this appliance.

Failure to convert the appliance correctly could



invalidate any warranty or liability claims and lead to prosecution.

The conversion instructions must be used in



conjunction with the rest of the appliance instruction, in particular for information on Standards, cooker positioning, connection, hose suitability, etc.

When servicing or replacing gas-carrying



components, disconnect from the gas before starting, and check that the appliance is gas sound after completion.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity supply before



conversion. Before electrical reconnection, check that the appliance is electrically safe.

Fig. 8.3

(Fascia may dier from that shown)

ArtNo.0102-0011 - Screwing

the control valve bypass screw

Injectors

Remove the burner caps and heads. Remove the old jets. Fit the new jets: see ‘Technical Data’ section for correct jets. Reassemble in the reverse order (Fig. 8.1).

Tap Adjustment

Removing the Control Panel

Pull o all the control knobs. Remove the 3 xing screws underneath the control panel.

The control panel will drop down slightly. It is held at the top by two holes in the top edge, one at each end, that locate on the tags on the inner panel (Fig. 8.2 ). Lift the control panel clear of the tags and pull forwards, taking care not to damage or strain the wiring.

Bypass Screw Adjustment

Turn the bypass screw on each control clockwise to the stop (Fig. 8.3).

Ret the control panel.

Page 37

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.103-0006 - Maxitrol cap & converter

Nut

Snap-in converter device

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

Set the Governor

Unscrew the governor’s brass top. In the base of the brass top is a plastic snap-in converter device (Fig. 8.4). To convert the governor, snap the device out of the top and ret it the other way round. The snap-in converter device is marked to show the gas for which it is set (Fig. 8.5).

Make sure the device is secure in the top cap and ret the cap to the governor.

Pressure Testing

The pressure test point is accessible on the inlet pipe at the rear. Remove the test nipple screw and t a pressure gauge to the test point. Turn on and light two of the hotplate burners.

For Propane X cookers the pressure should be 2.54 kPa.

Make sure that the appliance is gas sound.



Check the operation of all the burners.



Affix Label

Stick the appropriate gas label over the natural gas part of the appliance data label.

Fig. 8.4

Fig. 8.5

ArtNo.102-0007 - Maxitrol converter device positions

Page 38

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

9. Servicing

Fig. 9.1

Fig. 9.2

ArtNo.090-0021 Hotplate removal

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS TURN OFF THE GAS SUPPLY

Check the appliance is gas sound after completion



of service. When checking for gas leaks DO NOT use washing up liquid – this can corrode. Use a product specically manufactured for leak detection.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity supply before



servicing, particularly before removing any of the following: control panel, side panels, hotplate tray or any electrical components or covers.

Before electrical reconnection, check that the



appliance is electrically safe.

1 Panels

1.1 To Remove the Control Panel DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull o all the control knobs.

Open the grill and right-hand oven doors and remove the 4 xing screws underneath the control panel.

The control panel should drop down slightly. It is held at the top by 2 holes in the top edge, one at each end, that locate on tags on the inner panel (Fig. 9.1). Clear the control panel holes from the inner panel and pull the control panel forward.

Disconnect the wiring from the rear.

Reassemble in reverse order. When replacing the leads refer to the wiring diagram. Check the operation of the timer.

1.2 To Remove the Side Panels DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.1). Pull the cooker forward. Remove the 4 retaining screws for each panel (1 at the front base, one on the top and 2 at the rear).

Reassemble in reverse order.

Page 39

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

2 Hotplate

2.1 To Remove the Hotplate DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the pan supports and burner heads. Remove the screws holding the hotplate burners to the hotplate.

Remove the 6 screws holding the hotplate tray to the cooker (Fig. 9.2).

Taking care not to damage the burner electrodes, carefully lift the hotplate. From underneath, disconnect the earth lead at the right-hand rear from the rear cross member and withdraw the hotplate.

Reassemble in reverse order, making sure that you reconnect the leads. Take care not to damage the burner ignition electrodes.

IMPORTANT: Make sure you replace the rear earthing leads when retting the xing screws as they form part of the cooker earthing.

Check for correct burner operation.

2.2 To Replace the Hotplate Control Taps DISCONNECT FROM THE ELECTRICITY SUPPLY.

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS, TURN OFF THE GAS SUPPLY.

Remove the control panel and hotplate (see 1.1 & 2.1). Unplug the FSD lead from the rear of the tap. Undo the compression tting at the rear of the tap and remove the xings that secure the tap to the gas rail. Disconnect the ignition switch wiring.

Remove the tap. Remove and discard the gasket seal. Fit the new gasket seal to the replacement tap. Reassemble in reverse order. Check that the appliance is gas sound. Verify the hotplate ignition.

The burners are xed to the support struts with 2 screws. Remove the appropriate burner and t the new one.

Reassemble in reverse order. Check that the burner operation is satisfactory.

Right-hand Wok Burner

Disconnect the burner feed pipes at the burner. Fit the new one and reassemble in reverse order. Check the burner operation.

2.6 To Change a Hotplate Burner Thermocouple DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.1 & 2.1).

Unplug the FSD lead from the rear of the tap.

The thermocouple sits in a hole that has a slot at one side. Ensure that the thermocouple is cool. Turn the thermocouple so that the earth lead (no sleeve) is in line with the slot. Lift the thermocouple clear of the hole.

Reassemble in reverse order.

3 Control Panel

3.1 To Replace the Ignition or light Switch DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.1).

Note: The old switch may be destroyed during removal. Remove the old switch from its bezel by gripping the switch body behind the control panel and twisting sharply. Remove the switch bezel by folding back the locking wings and pushing forward.

To t the new bezel to the control panel, rst line up the raised key on its body with the cut-out in the control panel and push it in from the front.

2.3 To Change a Hotplate Burner Injector

Remove the burner cap and head. Remove the old jet.

Fit the new injector. Reassemble in reverse order. Check the appliance is gas sound.

2.4 To Replace a Hotplate Burner Electrode

Lift o pan supports and remove the burner cap. Remove the screw holding the electrode. Pull the electrode vertically up suciently to grip the lead between thumb and forenger.

Pull o the electrode, but keep hold of the lead. Fit the new electrode to the lead. Fix the electrode in the burner with screw. Replace the burner cap.

Check the burner ignition. Replace the pan supports.

2.5 To Replace a Hotplate Burner

Remove the hotplate tray (see 2.1). The burners (except the right-hand wok burner) are mounted on support struts. For these burners, disconnect the burner feed pipes at the burner. Remove the screws at the front and rear holding the support struts. Lift the strut and burners clear.

Assemble the new switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front.

Replace the control panel in reverse order and test for correct operation.

3.2 To Replace the Clock DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.1). Pull o the timer control buttons.

Undo the timer xing screws and remove the timer mounting bracket assembly from the control panel.

Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case, and at the same time pulling the unit forward.

Reassemble in reverse order. When replacing the leads, refer to the wiring diagram. Check the operation of the timer.

Page 40

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

Fig. 9.3

ArtNo.320-0020 Oven back fixing screws

3.3 To Change the Ignition Generator DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forwards to gain access to the cover box at the rear of the cooker. Remove the screws securing the cover and lift clear. Pull o all the leads to the generator noting their positions. Slacken the 2 screws holding generator to cooker and remove the generator.

Fit the new generator to the cooker and replace the leads. Refer to the wiring diagram and reassemble in reverse order. Check ignition performance.

4 Grill

4.1 To Replace the Grill Controller DISCONNECT FROM THE ELECTRICITY SUPPLY.

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS, TURN OFF THE GAS SUPPLY.

Remove the control panel and hotplate (see 1.1 & 2.1). Disconnect the wiring from controller. Remove the 2 screws holding the controller to the mounting panel.

Fit the new controller and reassemble in reverse order. Check for correct operation.

4.2 To Replace the Grill Element DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the grill pan from the grill chamber. From inside the grill compartment, undo the 2 screws and washers and remove the enamelled front shield from the grill roof. Remove the 2 screws and washers securing the grill element front support. Remove the screws from the grill elements.

Carefully lift the elements out and, noting their positions, disconnect the leads from the element terminals.

If it is not possible to disconnect the leads in this way, pull cooker forwards to gain access to the rear. Remove the screws securing the electric cover to the back sheet, and then remove cover and disconnect the terminals from the rear.

Fit the new elements and reassemble in reverse order. Check the operation of the grill.

5 Ovens

5.1 To Remove the Oven Inner Back

Main Oven

Open the main oven door. Remove the 4 screws and washers securing the inner back to the back of the oven (Fig. 9.3). Carefully lift away the inner back.

Reassemble in reverse order, making sure that you fully tighten the 4 screws and washers.

Tall Oven

Open the tall oven door and remove the 2 screws and washers securing the inner back to the back of the oven. Carefully lift away the inner back. Reassemble in reverse order. Check the door for correct operation.

Page 41

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

5.2 To Change the Oven Fan DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forward to gain access to the rear. Remove the screws securing the electric cover to the back sheet and remove the cover. Disconnect the 3terminals connected to the fan, noting their position.

Remove the oven inner back (see 5.1). Hold the fan blade and remove the centre nut (left-hand thread), 2 brass washers, fan blade and circlip. Unscrew the fan retaining nuts and washers (3 o each) and lift the fan away from the rear of the cooker.

Fit the new fan and reassemble in reverse order. Check the operation of the oven.

5.3 To Replace an Oven Element DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the oven inner back (see 5.1). Remove the 2 screws from the top of the element and

the 1 from the bottom of the element (Fig. 9.4). Carefully lift the element out, disconnecting the terminals connected to the element (noting their positions).

If it is not possible to disconnect the leads in this way, pull the cooker forward to gain access to the rear, remove the screws securing the electric cover to the back sheet, remove the cover and disconnect the terminals from the rear.

Element ﬁxing screws

ArtNo.321-0005 Fan oven element

A – Thermostat capillary, B – Earthing plate

Fig. 9.4

Fig. 9.5

Fit the new element and reassemble in reverse order. Check the operation of the oven.

5.4 To Remove an Oven Element Thermal Cut-Out DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forward to gain access to the cover box. Undo the cover screws and lift clear. The cut-out is located on the earth plate beside the oven element connections. Disconnect the cut-out wiring. Undo the xings that secure the cut-out to the earth plate and remove.

Fit the replacement control and re-assemble in reverse order.

5.5 To Replace an Oven Thermostat DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.1 & 2.1). Open the oven door and remove the oven furniture.

Main Oven

Pull the cooker forward to gain access to the cover box at the rear of the cooker. Remove the 4 screws securing the cover and lift clear. The oven thermostat capillary is clamped to the oven back sheet with an earthing plate. Remove the screws and plate (Fig. 9.5).

Tall Oven

The oven thermostat capillary is clamped to the righthand rear upright with an earthing plate.

Remove the thermostat phial cover (2 screws). Unclip the thermostat phial from the clips in the oven back.

Page 42

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.320-0006 Oven door hinge adjustment 1

ArtNo.320-0001 Door hinges

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

Fig. 9.6

Fig. 9.8

Fig. 9.9

Centreline of hinge pin

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

Fig. 9.7

For either oven, feed the thermostat capillary out of the oven. Disconnect the wiring from the thermostat. Remove the 2 screws holding the thermostat to the mounting panel. Fit the new thermostat and reassemble in reverse order. Make sure that the phial is clipped to the oven back with the phial centrally positioned between the clips.

Remember to ret the earthing plate.

Check the operation of the thermostat.

6 Doors

6.1 To Remove the Grill Door

Remove the left-hand side panel (see 1.2). Remove the plinth (4 screws) and the central vertical cover (5screws). Remove the 2 countersunk screws (1 each side) securing the grill hinge arms to the front of the grill chamber.

Note: The arms are spring tensioned. Carefully remove the grill door. Retain the gaskets.

Reassemble in reverse order, making sure that the gasket is tted between the hinge arm and the front of the grill chamber.

Eect of hinge adjustment – exagerrated for clarity

Fig. 9.10

ArtNo.320-0002a Proplus oven door side screws

6.2 To Replace the Main Oven Door

Open the oven door. Support the door and loosen the 2 screws securing the upper hinge and gasket to the cooker front (Fig. 9.6).

The door is heavy, so take care.



Support the door and remove the screw nearest the hinge pin (Fig. 9.7). Swing the hinge up and away from the door hinge pin. Lift the door away from the lower hinge and remove.

Reassemble in reverse order.

6.3 To Adjust the Main Oven Door Angle

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig. 9.8). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig. 9.9).

Retighten the hinge screws.

6.4 Main Oven Door Glass

The glass on the oven door is not replaceable.

6.5 To Replace an Oven Door Outer Panel

Move the cooker forwards to gain access to the sides.

Open the oven door slightly and remove the 4 front panel xing screws from the door sides (2 each side), (Fig. 9.10). Carefully lift o the outer door panel.

Remove the door handle from the panel by unscrewing the 2 retaining nuts.

Fit the door handle to the new panel.

Fit the panel to the door. Reassemble in reverse order.

Page 43

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.320-0005 Oven door rubber seal

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

6.6 To Change the Main Oven Door Latch

Remove the outer door panel (see 6.5). Remove screws ‘B’, which hold the latch assembly to the inner door panel (Fig. 9.11). Fit the new catch and reassemble in reverse order. Check the door operation.

6.7 To Adjust the Main Oven Door Catch Keep

Open the oven door, slacken o the locknut at the base of the keep, and screw in or out as required until the required t is obtained. Retighten the locking nut

(Fig. 9.12).

6.8 To Remove the Tall Oven Door

Open the oven door. Supporting the door, remove the 2 screws securing the upper hinge and packing to the cooker front. Remove the door from the lower hinge by lifting slightly and moving outwards.

Reassemble in reverse order.

6.9 To Replace the Tall Oven Door Outer Panel

Remove the tall oven door (see 6.8). Lay the door face down on a suitable surface and remove the 2 screws from bottom edge of door and the 2 screws from the inside face of the door.

Fig. 9.11 Fig. 9.12

ArtNo.320-0004 Oven door keep

ArtNo.320-0003 Oven door latch

Fig. 9.13

Remove the outer door panel. Remove the door handle by unscrewing the 2 screws.

Remove the 2 cross-headed screws holding the door handle xing bracket to the door panel. Fit the door handle bracket and the door handle to the new panel.

Fit the panel to the door and reassemble in reverse order.

6.10 To Replace the Tall Oven Door Magnetic Latch

Remove the control panel (see 1.1). Remove the plinth (3 screws) and the central vertical cover (5 screws). Lever the retaining clip o the magnet unit.

Fit the new unit and retaining clip, and reassemble in reverse order. Check the door operation.

6.11 To Change an Oven Door Seal

Open the oven door. The seal is held in place by small hooks on the rear face. At the corner, pull the seal diagonally away from the door centre until that hook is released (Fig. 9.13). Proceed to the next hook and release it in a similar way, and so on. Use force if the hooks are sti, as the old seal will be discarded.

When tting the new seal, position the seal join at the bottom. Hook the new seal in one of the corner holes of the door, and proceed round the door, snapping in each hook in turn.

Page 44

10. Circuit Diagram

v r

r b br

P095199

b b

b a

v b

b b b b bbr br br br

A N

Key

The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.

Code Description

A1 Grill control

A2 Grill element right-hand side

A3 Grill element left-hand side

B1 Left-hand fan oven thermostat

B2 Left-hand fan oven control

B3 Left-hand fan oven element

B4 Left-hand fan oven fan

C Clock

D1 Right-hand fan oven thermostat

D2 Right-hand fan oven control

D3 Right-hand fan oven fan element

D4 Right-hand fan oven fan

F1 Oven light switch

Code Description

F2 Oven lamp

G1 Ignition switch

G2 Ignition spark generator

H Neon

I Thermal cut-out

J Connector

Code Colour

b Blue

br Brown

bk Black

or Orange

r Red

v Violet

w White

y Yellow

g/y Green/yellow

gr Grey

Page 45

11. Technical Data

DocAUS.102-0002 - Technical data - 90DF - Prof+

This cooker is designed for use on Natural Gas, although a

conversion for LP (

LPG X Propane (2.54 kPa)

gas is packed with the

cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back. The serial number is repeated on the badge below the left-hand oven door opening.

COUNTRY OF DESTINATION: Australia.

Connection & Test Pressures

Gas (Rp ½ at rear right-hand side) Electric

Natural gas Propane 2.54 kPa

1 kPa

230 V 50 Hz

See the appliance badge for test pressures.

Dimensions

Overall height minimum 900 mm maximum 925 mm Overall width 900 mm Overall depth 600 mm (to fascia); 650 mm (over handles) Minimum height above the hotplate 650 mm

Refer to ‘Positioning the Cooker’.

Ratings

Hotplate

Wok burner 55 15.2 MJh

Large burner 41 12.3 MJh Medium burner 33 6.2 MJh Small burner 25 3.7 MJh

Bypass Screw*

Input

Injector

Marking Size Ø Marking Size Ø

internal 88 0.88 mm

-1

external 168 1.68 mm external 98 0.98 mm

-1

165 1.65 mm 12.0 MJh 115 1.15 mm 6.2 MJh

92 0.92 mm 3.3 MJh

Input

15.0 MJh

internal 57 0.57 mm

-1

Injector

89 0.96 mm 67 0.68 mm 48 0.50 mm

Gas burner inputs based on Gross Caloric Value.

* The valves in this cooker are tted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural gas. For LPG conversion the bypass screws must be screwed all the way down.

Oven Efficiency

Natural Gas 1.0 kPa Propane 2.54 kPa

Ovens

Maximum power output @ 230 V 50 Hz 2.5 kW 2.5 kW Energy eciency class on a scale of A (more ecient) to G (less ecient) A A Energy consumption based on standard load Usable volume (litres) 69 66 Size Large Large Time to cook standard load 38 minutes 49 minutes Surface area of the grid

Main Oven Tall Oven

Forced air convection Forced air convection

0.90 kWh 0.99 kWh

1400 cm

790 cm

Grill 2.3 kW

Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.): 7.4kW.

Page 46

Clarence Street, Royal Leamington Spa,

Warwickshire, CV31 2AD, England.

Tel: +44 (0) 800 804 6261 | +44 (0) 370 789 5107

E-mail: consumers@falconappliances.co.uk