Page 1
Hi-LITE 110 Dual Fuel
USER GUIDE &
INSTALLATION INSTRUCTIONS
Page 2
METHOD
1. For the soufflŽ, press the raspberries through a fine
sieve to produce 180 g of purŽe. Put this into a heavybottomed pan, add the lemon juice and reduce down to
a thick jam, stirring from time to time and being careful
not to let it catch and burn.
2. Put 45 g of the sugar in a separate pan. Melt it and then
boil until it becomes a thick syrup (121 ¡C on a sugar
thermometer). To test without a thermometer, dip a
teaspoon into the syrup and then dip quickly into cold
water. You should be able to roll the cooling syrup into
a ball between your fingers. Be careful as the syrup is
extremely hot. When it has reached the right point, stir
the hot syrup into the raspberry jam.
3. Mix the framboise and cornflour together and stir into
the jam over the heat. Turn the jam into a small bowl,
sprinkle the surface with icing sugar and cover with cling
film.
4. Preheat the oven (not grill) to 180 ¡C shelf level 2
(conventional oven), 160 ¡C (fan oven) or gas mark 4
centre shelf.
5. Whisk the egg whites with the cream of tartar until you
can form soft peaks, then fold in the remaining caster
sugar. Lightly fold the whites into the jam, leaving thin
traces of white visible in the mixture.
6. Spoon into four large buttered and sugared ramekins,
place these on a baking tray and bake for 10 minutes.
7. Dust with icing sugar.
INGREDIENTS
¥ 400 g raspberries
¥ 1 tbsp lemon juice
¥ 100 g caster sugar
¥ 2 tsp cr�me de framboise
¥ 1 tsp cornflour
¥ 180 g egg whites (about 6)
¥ Pinch of cream of tartar or a squeeze of lemon juice
¥ Icing sugar for dusting
RASPBERRY SOUFFLÉ
SLOW BAKED LEG OF LAMB
METHOD
1. Preheat the oven to 220 ¡C (for a conventional oven), 200 ¡C
(for a fan oven) or gas mark 7.
2. Pull the small sprigs off the rosemary branches and set aside
with the garlic.
2. Using the tip of a paring knife, make up to 20 well-spaced
cuts into the flesh of the lamb, about 2.5 cm inch deep.
Divide the rosemary sprigs, garlic and anchovies and push
down into the cuts. Place the leg on a large roasting tin and
pour over the oil, massaging it all over the joint. Season well
with salt and pepper and pour the wine and 250 ml water
into the tin.
3. Put into the oven and sear for 15 minutes, then turn the
temperature right down to 130 ¡C (conventional oven),
110 ¡C (fan oven) or gas mark 1 and roast for 4Ð5 hours,
basting every 30 minutes or so. Basting frequently helps
to keep the meat moist and encourages the build up of a
good glaze on the outside. Add more liquid (wine or water)
if the tin looks dry Ð there should always be liquid in the tin
throughout this cooking process.
4. The meat is ready when it starts to fall off the bone, at which
point it should have a core temperature of 90 ¡C. Remove
from the oven, transfer to a warmed carving dish, cover
loosely with foil and leave to rest in a warm place for 30Ð45
minutes before carving.
5. Pour the juices from the tin into a tall hi-ball glass and allow
to settle. Spoon the fat from the top of the glass. There
should be enough sticky, reduced juices for an intense gravy
hit Ð if not, pour the juices you have back into the roasting
tin and put it over the heat, pour in a splash of water or wine
and deglaze the tin scraping up all the sticky bits from the
base. Boil fast until syrupy, taste and correct the seasoning.
INGREDIENTS
¥ 2Ð3 large sprigs of rosemary
¥ 4 large garlic cloves cut in half lengthways
¥ 1.8 kg leg of lamb
¥ 8 good quality anchovy fillets, halved
¥ 100 ml olive oil
¥ 250 ml dry red wine
¥ Maldon salt and freshly ground black pepper
Page 3
i
1. Before You Start... 1
Important! 1
Installation and Maintenance 1
Peculiar Smells 1
If You Smell Gas 1
Ventilation 1
Personal Safety 1
Ceramic Warming Zone 2
Cooker Care 3
Cleaning 3
2. Cooker Overview 4
Hotplate Burners 4
Wok Burner 5
The Wok Cradle
(Optional) 6
The Griddle 6
Warming Zone 7
The Grill 7
The Ovens 8
Operating the Ovens 8
The Browning Element 8
Fascia Illumination 8
The Clock 9
Accessories 11
Oven Lights 11
Storage 11
3. Cooking Tips 12
Tips on Cooking with the Timer 12
General Oven Tips 12
4. Cooking Table 13
5. Cleaning Your Cooker 14
Essential Information 14
Hotplate Burners 14
Ceramic Warming Zone 15
The Griddle 15
Glide-out Grill 16
Control Panel and Doors 17
Ovens 17
Cleaning Table 18
6. Troubleshooting 19
7. Installation 22
Dear Installer 22
Safety Requirements and Regulations 22
Provision of Ventilation 22
Location of Cooker 22
Conversion 22
Positioning the Cooker 24
Moving the Cooker 24
Fitting the Stability Bracket or Chain 25
Repositioning the Cooker Following
Connection
25
Gas Connection 26
Electrical Connection 26
Final Checks 27
Fitting the Plinth 27
Customer Care 27
8. Conversion to LP Gas 28
Hotplate 28
Ax Label 28
Pressure Testing 29
9. Circuit Diagram 30
10. Technical Data 31
Contents
Hi-LITE 110DF U110300-01A
Page 4
ii
Page 5
1
Your cooker should give you many years of trouble-free
cooking if installed and operated correctly. It is important
that you read this section before you start, particularly if you
have not used a dual fuel cooker before.
Important!
This appliance is designed for domestic cooking
only. Using it for any other purpose could invalidate
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen –
besides invalidating claims this wastes fuel and may
overheat the control knobs.
Installation and Maintenance
This cooker must be installed in accordance with the relevant
instructions in this booklet, with the relevant national and
local regulations, and with the local gas and electricity supply
companies’ requirements.
Make sure that the gas supply is turned on and that the
cooker is wired in and switched on (the cooker needs
electricity).
Set the clock to make sure that the oven is functional – see
the relevant section in this manual.
Only a qualied service engineer should service the cooker,
and only approved spare parts should be used.
Always allow the cooker to cool and then switch it o at the
mains before cleaning or carrying out any maintenance work,
unless specied otherwise in this guide.
Peculiar Smells
When you rst use your cooker it may give o an odour. This
should stop after use.
Before using your cooker for the rst time, make sure that all
packing materials have been removed and then, to dispel
manufacturing odours, turn all the ovens to 200 °C and run
for at least an hour.
Before using the grill for the rst time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back, and the grill door open.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
If You Smell Gas
• DO NOT turn electric switches on or off
• DO NOT smoke
• DO NOT use naked flames
• DO turn off the gas at the meter or cylinder
• DO open doors and windows to get rid of the gas
• DO keep people away from the area affected
• Call your gas supplier
Ventilation
CAUTION: The use of a gas cooking appliance results in
the production of heat and moisture in the room in which
it is installed. Therefore, make sure that the kitchen is
well ventilated: keep natural ventilation holes open or
install a powered cooker hood that vents outside. If you
have several burners on, or use the cooker for a long time,
open a window or turn on an extractor fan.
Personal Safety
DO NOT modify this appliance.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in
a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
This appliance is not intended for use by young
children or inrm persons unless they have been
adequately supervised by a responsible person to
make sure that they can use the appliance safely.
CAUTION: A long term cooking process has to be
supervised from time to time. A short term cooking
process has to be supervised continuously.
Danger of re: DO NOT store items on the cooking
surfaces.
To avoid overheating, DO NOT install the cooker
behind a decorative door.
WARNING: The appliance and its accessible parts
become hot during use and will retain heat even
after you have stopped cooking. Care should be
taken to avoid touching heating elements. Children
less than 8 years of age shall be kept away unless
continuously supervised.
DO NOT use a steam cleaner on your cooker.
Always be certain that the controls are in the OFF position
when the oven is not in use, and before attempting to clean
the cooker.
1. Before You Start...
Page 6
2
When the oven is on, DO NOT leave the oven door
open for longer than necessary, otherwise the
control knobs may become very hot.
When using the grill, make sure that the grill pan
is in position and pushed fully in, otherwise the
control knobs may become very hot.
DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Always keep combustible materials, e.g. curtains, and
ammable liquids a safe distance away from your cooker.
Never store ammable materials in the drawer.
This includes paper, plastic and cloth items, such
as cookbooks, plastic ware and towels, as well as
ammable liquids. Do not store explosives, such as
aerosol cans, on or near the appliance.
DO NOT spray aerosols in the vicinity of the cooker
while it is on.
Use dry oven gloves when applicable – using damp gloves
might result in steam burns when you touch a hot surface.
Do not use a towel or other bulky cloth in place of a glove – it
might catch re if brought into contact with a hot surface.
NEVER operate the cooker with wet hands.
DO NOT use aluminium foil to cover shelves, linings
or the oven roof.
DO NOT use hotplate protectors, foil or hotplate
covers of any description. These may aect the safe
use of your hotplate burners and are potentially
hazardous to health.
NEVER heat unopened food containers. Pressure
build up may make the containers burst and cause
injury.
DO NOT use unstable saucepans. Always make sure
that you position the handles away from the edge of
the hotplate.
DO NOT use cooking vessels on the hotplate that
overlap the edges.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on re. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
WARNING!
Unattended cooking on a hob with fat or oil can be
dangerous and may result in re.
NEVER leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
Do not use the top of the ue (the slots along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.
DO NOT use water on grease res and never pick
up a aming pan. Turn the controls o and then
smother a aming pan on a surface unit by covering
the pan completely with a well tting lid or baking
tray. If available, use a multi-purpose dry chemical
or foam-type re extinguisher.
Cooking high moisture content foods can create a ‘steam
burst’ when the oven door is opened (Fig.1-1). When
opening the oven stand well back and allow any steam to
disperse.
Take care that no water seeps into the appliance.
This appliance is heavy so take care when moving it.
Ceramic Warming Zone
NEVER attempt to cook on the warming zone.
DO NOT use the warming zone surface as a cutting
board.
Do not leave utensils, foodstus or combustible items on the
warming zone when it is not in use (e.g. tea towels, frying
pans containing oil).
DO NOT place plastic or aluminium foil, or plastic
containers, on the warming zone.
DO NOT leave the warming zone switched on unless
being used for warming.
Do not stand or rest heavy objects on the warming zone.
Although the ceramic surface is very strong, a sharp blow or
sharp falling object (e.g. a salt cellar) might cause the surface
to crack or break (Fig.1-2).
Should a crack appear in the surface, disconnect the
cooker immediately from the supply and arrange for
its repair.
Always LIFT pans o the warming zone. Sliding pans may
cause marks and scratches (Fig.1-3). Always turn the control
to the ‘OFF’ position before removing a pan.
DO NOT place anything between the base of the pan and
the warming zone surface (e.g. asbestos mats, aluminium foil,
wok cradle).
Page 7
3
ArtNo.324-0001 Steam burst
Avoid warming an empty pan. Doing so may damage
both the warming zone and pan.
Take care NOT to place metallic objects such as
knives, forks, spoons and lids on the hob surface
since they can get hot.
The appliance is not intended to be operated by
means of external timer or separated remote-control
system.
Only certain types of glass, glass-ceramic, earthenware or
other glazed containers are suitable for use on the warming
zone; others may break because of the sudden change in
temperature.
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours.
Cleaning
In the interests of hygiene and safety, the cooker should be
kept clean at all times as a build up in fats and other food
stu could result in a re.
Clean only the parts listed in this guide.
Clean with caution. If a wet sponge or cloth is used to wipe
spills on a hot surface, be careful to avoid steam burns. Some
cleaners can produce noxious fumes if applied to a hot
surface.
Fig.1-1
ArtNo.312-0003 Moving pans
Fig.1-2
Fig.1-3
Page 8
4
2. Cooker Overview
The 110 dual fuel cooker (Fig.2-1) has the following features:
A. 4 hotplate burners, a warming zone and wok burner
B. A control panel
C. A grill
D. Conventional oven
E. Fan oven
F. Storage drawer
Hotplate Burners
The image above each of the control knobs indicates which
burner that knob controls.
Each burner has an Flame Supervision Device (FSD) that
prevents the ow of gas if the ame goes out.
When the igniter button is pressed in, sparks will be
made at every burner – this is normal. Do not attempt to
disassemble or clean around any burner while another
burner is on, otherwise an electric shock could result.
To light a burner, press the igniter button, and push in and
turn the associated control knob to the high position as
indicated by the large ame symbol (
), (Fig.2-2).
1
2
3
3
2
1
220
180
140
100
220
180
140
100
1
3
3
1
100
100
C
B
D
A
F
E
Fig.2-1
Fig.2-2
DocNo.020-0013 - Overview - 110DF - Classic, RM & Toledo lidded
Page 9
5
The igniter should spark and light the gas. Keep holding the
knob pressed in to let the gas through to the burner for about
ten seconds.
If, when you let go of the control knob, the burner goes out,
then the FSD has not been bypassed. Turn the control knob
to the OFF position and wait for one minute before you try
again, this time making sure to hold in the control knob for
slightly longer.
Adjust the ame height to suit by turning the knob. On this
cooker the low position is beyond high, not between high
and o. The ‘small ame’ marks the low setting (Fig.2-3).
If a burner ame goes out, turn o the control knob and
leave it for one minute before relighting it.
Make sure that the ames are under the pans. Using a lid will
help the contents boil more quickly (Fig.2-4).
Large pans should be spaced well apart.
Pans and kettles with concave bases or down-turned base
rims should not be used (Fig.2-5).
Simmering aids, such as asbestos or mesh mats, are
NOT recommended (Fig.2-6). They will reduce burner
performance and could damage the pan supports.
You should also avoid using unstable and misshapen pans
that may tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers (Fig.2-7).
The minimum recommended pan diameter is 120 mm. The
maximum allowable pan base diameter is 260 mm.
DO NOT use cooking vessels on the hotplate that overlap the
edges.
Wok Burner
The wok burner is designed to provide even heat over a large
area. They are ideal for large pans and stir-frying (Fig.2-8).
For heating smaller pans, the aforementioned hotplate
burners may be more ecient.
You should wipe the enamel top surface of the cooker around
the hotplate burners as soon as possible after spills occur. Try
to wipe them o while the enamel is still warm.
Note:
The use of aluminium pans may cause metallic marking
of the pan supports. This does not aect the durability of the
enamel and may be cleaned o with an appropriate metal
cleaner.
ArtNo.311-0005 Wok burner & pan support
Fig.2-8
ArtNo.311-0002 Pan with rim
Fig.2-5
ArtNo.311-0001 Right pans gas
Fig.2-4
Art No. 311-0003 Simmer aids
Fig.2-6
ArtNo.311-0004 Tipping wok
Fig.2-7
Fig.2-3
Page 10
6
1
2
3
3
2
1
220
180
140
100
220
180
140
100
1
2
3
3
2
1
220
180
140
100
220
180
140
100
ArtNo.311-0006 Correct wok sizes
The Wok Cradle (Optional)
The wok cradle is designed to t a 35 cm wok. If you use a
dierent wok, make sure that it ts the cradle. Woks vary very
widely in size and shape. It is important that the wok sits
down on the pan support – however, if the wok is too small,
the cradle will not support it properly (Fig.2-9).
The cradle should be used on the wok burner only. When you
t the cradle, make sure that it is supported properly on a pan
support and the wok is sitting level in the cradle (Fig.2-10).
The cradle will get very hot in use – allow plenty of time for it
to cool before you pick it up.
The Griddle
The griddle ts the left-hand pan support, front to back
(Fig.2-11). It is designed for cooking food on directly. DO NOT
use pans of any kind on it. The griddle surface is non-stick and
metal cooking utensils (e.g. spatulas) will damage the surface.
Use heat resistant plastic or wooden utensils.
DO NOT put it crossways – it will not t properly and
will be unstable (Fig.2-12).
DO NOT put it on any other burner – it is not
designed to t in any of the other pan supports.
Position the griddle over the hotplate burners resting on the
pan support. Check that it is securely located.
The griddle can be lightly brushed with cooking oil before
use (Fig.2-13). Light the hotplate burners. Adjust the ame
heights to suit.
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. Turn the
control knobs towards the low position, marked with the
small ame symbol, to reduce the burner ames.
Always leave space around the griddle for the gases
to escape.
NEVER t two griddles side by side (Fig.2-14).
After cooking, allow the griddle to cool before cleaning.
Fig.2-11
Fig.2-12
Fig.2-9
ArtNo.311-0007 Wok stand close-up
Fig.2-10
ArtNo.311-0009 Oil on griddle
Fig.2-13
ArtNo.311-0008 Griddle positioning
Fig.2-14
Page 11
7
Warming Zone
On the right of the hob is the warming zone (Fig.2-15). Use
the warming zone for keeping food warm while the nal
touches are put to a meal. Turn the control knob clockwise to
the ‘On’ position.
For best results, preheat a covered serving dish for 10 minutes
before adding food to it.
Use only heat resistant dishes.
The Grill
CAUTION: This appliance is for cooking purposes
only. It must not be used for other purposes, for
example room heating.
CAUTION: Accessible parts may be hot when the grill
is in use. Young children should be kept away.
Open the door and pull the grill pan forward using the handle
(Fig.2-16).
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
Adjust the heat to suit by turning the control knob. To heat
the whole grill, turn the control knob clockwise (Fig.2-17).
To heat the right-hand half, turn the control knob counterclockwise. The neon indicator light by the grill control will
come on.
For best results, slide the grill pan back into the grill chamber
and preheat the appropriate part(s) of the grill for two
minutes. The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
Once the grill has preheated, slide the grill pan out again.
With the trivet back in place with the food on it, slide the grill
pan back into the grill chamber. Make sure that it is pushed
right in.
The grill trivet can be turned over to give two grilling
positions (Fig.2-18).
Do not leave the grill on for more than a few moments,
without the grill pan underneath it.
Never close the grill door when the grill is on.
ArtNo.331-0002 Grill pan high/low position
Fig.2-18
ArtNo.331-0001Grill pan pulled forwards
ArtNo.210-0001 Classic grill control
1
2
3
3
2
1
Fig.2-16
Fig.2-17
Fig.2-15
Page 12
8
The Ovens
The clock must be set to the time of day before the righthand oven will work. See the following section on ‘The
Clock’ for instructions on setting the time of day.
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
The left-hand oven is a conventional oven, while the righthand oven is a fan oven.
The Conventional Oven
A conventional oven has two heating elements – one visible
in the top of the oven and the other under the oven base.
Note: Be careful to avoid touching the top element and
element deector when placing or removing items from the
oven.
The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.
Similar items being cooked will need to be swapped around
for even cooking.
The Fan Oven
The right-hand oven is a fan oven that circulates hot air
continuously, which means faster, more even cooking.
The recommended cooking temperatures for a fan oven are
generally lower than a conventional oven.
Note: Please remember that all cookers vary so temperatures
in your new ovens may dier to those in your previous
cooker.
Operating the Ovens
Turn the oven knob to the desired temperature (Fig.2-19).
The oven indicator light will glow until the oven has reached
the temperature selected. It will then cycle on and o during
cooking (Fig.2-20).
The Browning Element
The Browning Element is positioned in the top of the lefthand oven. It can be used at the end of a normal cooking
period to give extra browning to au gratin dishes or give a
crisper nish to meat.
After the normal cooking is nished turn the left-hand
oven thermostat knob clockwise to the browning position,
indicated by (
) on the fascia panel.
Only the Browning Element will operate when the thermostat
is turned to this position. The top and base cooking elements
will switch o automatically.
Fascia Illumination
To turn on the fascia illumination panel simply push the
button in (Fig.2-21). To turn this feature o, push the button
once more.
Fig.2-20
220
180
140
100
Fig.2-19
Fig.2-21
Page 13
9
The Clock
You can use the clock to turn the right-hand oven on and o.
The clock must be set to the time of day before the oven
will work.
Note: When using the timer functions, rst set the clock as
required before setting the oven temperature.
Setting the Time of Day
The LCD clock is shown in (Fig.2-22). When the clock is rst
connected, the display ashes ( 0.00 ) and (G) alternately.
To set the time, turn and hold the Timer knob to the clock
symbol [
A
] and at the same time turn the Adjusting knob left
or right until the clock shows the time of day. Remember this
is a 24-hour clock. Let go of the Timer knob and it will spring
back to the vertical, oven manual setting.
IMPORTANT: The right-hand oven will not operate unless
the clock has been set.
Setting the Minute Minder
To activate the minute minder turn the Timer knob to the
right to the [C] minute minder setting – it should click into
position (Fig.2-23).
Rotate the Adjusting knob to set the time required (Fig.2-24).
You can either turn the knob back to the vertical manual
setting [
B
] to keep an eye on the time of day, or leave it in
the [C] minute minder position as the time ticks down.
To stop the beeper when it sounds, turn the Adjusting knob
counter-clockwise.
• The ‘cook period’, which is the length of time you
want the oven to cook for.
• The ‘stop time’, which is the time of day you want the
oven to stop cooking.
To Stop the Right-hand Oven at a Specic Time of Day
Turn the Timer knob to the [E] position (Fig.2-25).
Use the Adjusting knob to set the ‘stop time’. You can set
the oven to turn on at any time over the following 24-hour
period. AUTO shows in the display (Fig.2-26).
Turn the Timer knob to the bottom ‘AUTO’ setting to return to
the clock display.
Once the ‘stop time’ is reached, the beeper sounds. Turn the
Timer knob to the vertical [
B
] to return to manual cooking.
To Start and Then Stop the Right-hand Oven Using the
Timer
You cannot set a start time directly – this is set
automatically by a combination of the ‘cook time’ and
‘stop time’.
Turn the Timer knob to the [
D
] position (Fig.2-27).
Turn the Adjusting knob to set the ‘cooking time’ you need
(Fig.2-28).
ArtNo.300-0004 2-button clock annotated
A B
AUTO
A – Timer knob, B – Adjusting knob
Fig.2-22
AUTO
ArtNo.300-0006 2BC
minute minder setting 2
ArtNo.300-0004 2-button clock annotated
AUTO
AUTO
ArtNo.301-0008 2BC
Stopping the oven 2
AUTO
Fig.2-23
Fig.2-24
Fig.2-25
Fig.2-26
ArtNo.300-0004 2-button clock annotated
AUTO
ArtNo.301-0010 2BC
Setting the cooking time
AUTO
Fig.2-27
Fig.2-28
Page 14
10
Turn the Timer knob to the [E] position. The display will
show the current time of day plus the ‘cook time’ you just set.
Use the Adjusting knob to set the ‘stop time’ required
(Fig.2-29).
The ‘stop time’ is displayed, followed by ‘AUTO’. Set the oven
to the cooking temperature you need. Turn the Timer knob to
the ‘Auto’ setting.
When your cooking is nished, the beeper sounds. Turn the
Timer knob to the vertical [
B
] to return to manual cooking.
If you are out, do not worry about the beeper going o – it
stops on its own after a while. When you return, turn the
Timer knob to the vertical [
B
] to return to manual cooking.
AUTO is Showing, But You Want to Revert to Manual
Cooking
You can cancel any automatic settings by briey turning the
Timer knob to the clock symbol [A] and then releasing it.
Key Lock
When the key lock is activated the right-hand oven is locked
and will not come on.
The left-hand oven can be operated as usual.
To Activate the Key Lock
Make sure that the clock is in manual mode and cancel
any active programs.
Turn and hold the Timer knob to the clock symbol [
A
] for
about 8 seconds. ‘On’ appears on the display (Fig.2-30).
While still holding the Timer knob turned to the clock symbol
[
A
], turn the Adjusting knob clockwise until the key symbol
[F] and ‘OF’ shows on the display (Fig.2-31). Release the
knobs.
The right-hand oven is now locked, as is conrmed by the
display showing the time of day alongside the key symbol [
F
]
(Fig.2-32).
To Turn O the Key Lock
Turn and hold the Timer knob to the clock symbol [
A
] for
about 8 seconds. ‘OF’ will appear on the display (Fig.2-33).
While still holding the Timer knob turned to the clock symbol
[
A
], turn the Adjusting knob clockwise until the key symbol
[F] goes out on the display and ‘On’ shows (Fig.2-34). Let go
of the knobs.
After a few seconds, the display reverts to showing the time
of day.
The oven can now be used normally.
ArtNo.301-0008 2BC
Stopping the oven 2
AUTO
Fig.2-29
Art No. 301-0011 2BC
Activating the key lock 1
AUTO
ArtNo.301-0012 2BC
Activating the key lock 2
AUTO
ArtNo.301-0013 2BC
Activating the key lock 3
AUTO
ArtNo.301-0014 2BC
Deactivating the key lock 1
ArtNo.300-0004 2-button clock annotated
AUTO
ArtNo.301-0015 2BC
Deactivating the key lock 2
AUTO
Fig.2-30
Fig.2-31
Fig.2-32
Fig.2-33
Fig.2-34
Page 15
11
Accessories
Oven Shelves
The oven shelves (Fig.2-35) can be easily removed and
retted.
Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig.2-36).
Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward
(Fig.2-37).
To ret the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig.2-38).
The Handyrack (Conventional Oven)
The Handyrack (Fig.2-39) ts to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.
The maximum weight that can be held by the Handyrack
is 5.5 kg (12 lb). It should only be used with the supplied
roasting tin, which is designed to t the Handyrack. Any other
vessel could be unstable.
It can be tted at two dierent heights. One of the oven
shelves must be removed and the other positioned to suit.
When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.
To t the Handyrack, locate one side of it on the door bracket
(Fig.2-40).
Then spring the other side out to clip it onto the other
bracket (Fig.2-41).
Oven Lights
Press the button to turn the lights on (Fig.2-42).
If an oven light fails, turn o the power supply before
changing the bulb. See the ‘Troubleshooting’ section for
details on how to change the bulb.
Storage
The bottom drawer is for storing oven trays and other
cooking utensils. It can get very warm, so do not store
anything in it that may melt or catch re.
The drawer can be removed completely by pulling it right out
and up.
ArtNo.320-0013 Removing the shelf 3
ArtNo.320-0014 Handyrack on LH door
ArtNo.320-0015
Fitting the Handyack 1
Fig.2-39
Fig.2-40
ArtNo.320-0016
Fitting the handyrack 2
Fig.2-41
ArtNo.320-0011 Removing the shelf 1
ArtNo.320-0012 Removing the shelf 2
Fig.2-36 Fig.2-37
Fig.2-38
ArtNo.320-0026
- Oven light
Fig.2-42
Shelf guard
Front
Fig.2-35
Page 16
12
3. Cooking Tips
Tips on Cooking with the Timer
If you want to cook more than one dish, choose dishes that
require approximately the same cooking time. However,
dishes can be ‘slowed down’ slightly by using small containers
and covering them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or placing them in
larger containers.
Very perishable foods such as pork or sh should be avoided
if a long delay period is planned, especially in hot weather.
DO NOT place warm food in the oven to be timed.
DO NOT use a timed oven that is already warm.
DO NOT use the timed oven if the adjoining oven is
already warm.
Whole poultry must be thoroughly defrosted before being
placed in the oven. Check that meat and poultry are fully
cooked before serving.
Temperature (Gas Mark) Temperature (°C / °F)
1 140 / 275
2 150 / 300
3 160 / 325
4 175 / 350
5 190 / 375
6 205 / 400
7 220 / 425
8 230 / 450
Table 3-1 Temperature conversion table
General Oven Tips
The wire shelves should always be pushed rmly to the back
of the oven.
Baking trays with food cooking on them should be placed
level with the front edge of the oven’s wire shelves. Other
containers should be placed centrally. Keep all trays and
containers away from the back of the oven, as overbrowning
of the food may occur.
For even browning, the maximum recommended size of a
baking tray is 340 mm (13½”) by 340 mm (13½”).
When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.
• Always leave a “finger’s width” between dishes on
the same shelf. This allows the heat to circulate freely
around them.
• To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.
• Where dishes may boil and spill over during cooking,
place them on a baking tray.
• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your
Cooker’) work better when fat splashes are avoided.
Cover meat when cooking.
• Sufficient heat rises out of the oven while cooking to
warm plates in the grill compartment.
• If you want to brown the base of a pastry dish, preheat
the baking tray for 15 minutes before placing the dish in
the centre of the tray.
Page 17
13
4. Cooking Table
ArtNo.050-0007
Oven shelf positions
Oven Shelf Positions
Top (T)
Centre (C)
Base (B)
The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a
preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The
temperature in the fan oven does not vary with height in the oven so you can use any shelf.
Food
Meat
Beef (no bone)
Lamb
Pork
Poultry
Chicken
Turkey
Duck
Casserole
Yorkshire Pudding
Cake
Very rich fruit - Christmas,
wedding, etc.
Fruit 180 mm tin
Fruit 230 mm tin
Madeira 180 mm
Queen cakes
Scones
Victoria sandwich
180 mm tin
210 mm tin
Desserts
Shortcrust tarts
Fruit pies
Tartlets
Puff pastry
Meringues
Baked egg custard
Baked sponge pudding
Milk pudding
Bread
Fish
Fillet
Whole
Steak
Approximate Cooking Time
30-35 minutes per 500g +30-35 minutes.
20-25 minutes per 500g +20-25 minutes.
30-35 minutes per 500g +30-35 minutes.
25-30 minutes per 500g +25-30 minutes.
35-40 minutes per 500g +35-40 minutes.
25-30 minutes per 500g +25-30 minutes.
20-25 minutes per 500g +20-25 minutes.
15-20 minutes per 500g +15-20 minutes.
20 minutes per 500g +20 minutes.
15 minutes per 500g +15 minutes.
25-30 minutes per 500g.
20 minutes per 500g.
2-4 hours according to recipe.
Large tins 30-35 minutes; individual 10-20 minutes.
45-50 minutes per 500g of mixture.
2-2½ hours.
Up to 3½ hours.
80-90 minutes.
15-25 minutes.
10-15 minutes.
20-30 minutes.
30-40 minutes.
20-30 minutes on a preheated tray.
35-45 minutes.
10-20 minutes according to size.
20-40 minutes according to size.
2-3 hours.
45-60 minutes.
40-45 minutes.
2 to 3 hours.
20-30 minutes.
15-20 minutes.
15-20 minutes per 500g.
Steaks according to thickness.
Conventional Oven
Temperature °C
(Shelf Position)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
140-150 (C)
220 (C)
140 (C/B)
150 (C/B)
150 (C/B)
160 (C/B)
190 (C/B)
220 (C/B)
180 (C/B)
180 (C/B)
200 (C/B)
200 (C/B)
200 (C/B)
210 (C/B)
100 (C/B)
160 (C/B)
180 (C/B)
140-150 (C/B)
210 (C)
Fanned Grilling
190 (C/B)
190 (C/B)
190 (C/B)
Fan Oven
Temperature
°C
150
190
150
190
150
190
150
190
150
190
150
190
130-140
210
130
140
140
150
180
210
170
170
190
190
190
200
90
150
170
130-140
200
190 (C/B)
190 (C/B)
190 (C/B)
Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
220°C (210°C for fan oven) and the
cooking time adjusted accordingly.
For stuffed and rolled meats, add
approximately 10 minutes per 500g,
or cook at 200°C (190°C) for 20
minutes then 160°C (150°C) for the
remainder.
For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.
Using the conventional oven: when
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.
ArtNo.050-0001 Gas cooking table
Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340 mm
x 340 mm. This ensures free heat
circulation.
If cooking a two tier load, the trays
should be interchanged
approximately halfway though the
cooking time.
Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.
T - Top; C - Centre; B - Base
DocNo.031-0004 - Cooking table - electric & fan single cavity
Page 18
14
ArtNo.311-0032 Burner layout FSD
A
B
C
D
E
ArtNo.311-0033 Wok burner details FSD
A
B
C
D
E
ArtNo.311-0016 Fitting the burner inner head
A
B
Fig.5-1
Fig.5-2
Fig.5-3
Fig.5-4
A – Cap, B – Head, C – Notch, D – Base, E – Electrode
A – Inner burner cap, B – Outer burner cap, C – Inner burner head,
D – Outer burner head, E – Wok burner base
A – Electrode notch, B – Ignition electrode
5. Cleaning Your Cooker
Essential Information
Isolate the electricity supply before carrying out any
thorough cleaning. Allow the cooker to cool.
NEVER use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.
DO NOT mix dierent cleaning products – they may
react together with hazardous results.
All parts of the cooker can be cleaned with hot soapy water
– but take care that no surplus water seeps into the
appliance.
Remember to switch on the electricity supply and reset the
clock before re-using the cooker.
Hotplate Burners
The burner heads and caps can be removed for cleaning.
DO NOT put the burner heads in a dishwasher.
Make sure they are absolutely dry before replacing them.
The Single Ring Burners
When retting the burner head, make sure that the notch
lines up with the electrode or hole in the base. Check that the
burner head is level and that the cap is tted centrally on the
burner head (Fig.5-1).
The Wok Burner
The wok burner can also be taken apart for cleaning.
When reassembling the wok burner (Fig.5-2), turn over the
large base ring and nd the ‘D’ shaped area (Fig.5-3). Turn the
head until the ‘D’ matches the one on the burner base. Flip
the burner over once again and place it on the burner base.
To t the small inner burner, nd the larger electrode notch in
the burner rim. Line this up with the white ignition electrode
and place the inner burner on the large base ring (Fig.5-4).
Now t the two burner caps, making sure that they are seated
properly.
Check the burner ports are not blocked. If a blockage occurs,
remove stubborn particles using a piece of fuse wire.
The Wok Cradle
Recommended cleaning materials are hot soapy water, a
moistened soap pad, cream cleaner or a nylon scourer.
ArtNo.045-0004 - Cleaning - 90 induction - tpl glzd dr & GO grill
Page 19
15
Ceramic Warming Zone
Daily Care
First of all, be sure that the heat indicator light is o and that
the warming zone surface is cool.
Apply a small dab of ceramic cleaning cream in the centre
of the area to be cleaned. Dampen a clean paper towel and
work the cream onto the surface. As a nal step, wipe the
surface with a clean, dry paper towel.
Cleaning Spills
Turn o the unit and wipe the area surrounding the warming
zone with a clean paper towel. If a spill (other than a sugary
substance) is on the warming zone, do not clean until the
warming zone has completely cooled down, and then follow
the instructions below, ‘Cleaning Burned-on Spills’.
If you accidentally melt anything on the surface or if you spill
foods with a high sugar content (preserves, tomato sauce,
fruit juice, etc), remove the spill IMMEDIATELY with a razor
scraper, while the unit is still hot.
IMPORTANT: Use an oven glove to protect your hand from
potential burns.
Scrape the major spill or melted material from the warming
zone and push into a cold area. Then, turn the unit ‘OFF’ and
allow to cool before cleaning further. After the surface cools
down and the heat indicator lights go o, follow the ‘Daily
Care’ procedure outlined above.
Cleaning Burned-on Spills
Make sure that the heat indicator lights are o and that
the warming zone is cool. Remove the excess burned-on
substance with a single-edged razor scraper. Hold the scraper
at an angle of about 30° to the surface and then scrape o the
burned-on matter (Fig.5-5).
Once you have removed as much as possible with the scraper,
follow the ‘Daily Care’ procedure outlined above.
To Remove Metal Rub-off
Sliding pans on the warming zone – especially aluminium or
copper pans – can leave marks on the ceramic surface. These
marks often appear like scratches, but can easily be removed
(see ‘Cleaning Spills’). If the rub-o marks are especially
stubborn, use a cleaning cream together with the razor.
The Griddle
Always clean the griddle after use. Allow it to cool completely
before removing. Immerse the griddle plate in hot soapy
water. Use a soft cloth or, for stubborn stains, a nylon washing
up brush.
Note: If the griddle is washed in a dishwasher then some
dishwasher residue may appear on the back. This is normal
and will not aect the performance of your griddle.
Fig.5-5
Page 20
16
ArtNo.331-0001Grill pan pulled forwards
Fig.5-6
ArtNo.331-0003 Grill frame out, no pan
ArtNo.331-0004 Removing the grill frame
Fig.5-7
Fig.5-8
ArtNo.331-0005 Removing the grill rail
Fig.5-9
ArtNo.331-0006 Grill pan plan
Fig.5-10
Glide-out Grill
Before you remove any of the grill parts for cleaning
make sure that they are cool, or use oven gloves.
The grill pan and trivet should be washed in hot soapy water.
Alternatively, the grill pan can be washed in a dishwasher.
After grilling meats or any foods that soil, leave to soak for
a few minutes in the sink immediately after use. Stubborn
particles may be removed from the trivet by using a nylon
brush.
The grill pan can be easily removed for cleaning as follows:
Remove the grill pan support frame by pulling the grill pan
forward (Fig.5-6).
Lift the grill pan clear of the support frame.
The support frame
is held to the side rails by two clips on each side (Fig.5-7).
For each side, support the side rail with one hand and with
the other hand lift the frame up and out of the side clips
(Fig.5-8).
For safety, push the side rails back into the grill chamber.
If you need to remove the side rails to allow cleaning of the
grill chamber, you can unhook them from the grill chamber
sides (Fig.5-9) and wipe the sides clean with a soft cloth and
mild detergent.
DO NOT put the side runners in a dishwasher.
Once you have nished, hook the side rails back onto the
sides of the chamber. To ret the frame, pull the side rails
forward and, for each side in turn, support the side rail and
press the frame down into the side rails.
Replace the grill pan. When retting the grill pan, make sure
that the wide rim is at the front (Fig.5-10).
Page 21
17
Control Panel and Doors
Avoid using any abrasive cleaners, including cream cleaners.
For best results, use a liquid detergent.
The same cleaner can be used on the doors, or alternatively,
using a soft cloth wrung out in clean hot soapy water – but
take care that no surplus water seeps into the appliance.
After cleaning, polish with a dry cloth.
Glass Fronted Door Panels
The oven door front panels can be taken o so that the glass
panels can be cleaned. Move the cooker forward to gain
access to the sides (see the ‘Moving the Cooker’ section under
‘Installation’).
Open the oven door slightly and remove the front panel
xing screws from the door sides, two each side (Fig.5-11).
Carefully lift o the outer door panel. The inside face of the
glass panels can now be cleaned – take care not to disturb or
wet the door insulation.
Note: If the door is triple glazed then the inner two panels are
xed together and should not be separated. After cleaning,
carefully ret the outer door panel and replace the side xing
screws.
DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Ovens
'Cook & Clean' Panels
The ovens have side ‘Cook & Clean’ panels which have been
coated with a special enamel that partly cleans itself. This
does not stop all marks on the lining, but helps to reduce the
amount of manual cleaning needed.
These panels work better above 200 °C. If you do most of your
cooking below this temperature, occasionally remove the
panels and wipe with a lint free cloth and hot soapy water.
The panels should then be dried and replaced and the oven
heated at 200 °C for about one hour. This will make sure that
the panels are working eectively.
DO NOT use steel wool, oven cleaning pads, or any other
materials that will scratch the surface.
Removing the Oven Linings
Some of the lining panels can be removed for cleaning.
If you wish to clean the enamel interior of the oven, you
will need to remove the shelves before removing the ‘Cook
& Clean’ panels. You do not have to remove the support
brackets to remove the panels. Lift each panel upward and
slide forward o the support brackets (Fig.5-12).
Once the panels have been removed, the oven enamel
interior can be cleaned.
Ret in the reverse order.
ArtNo.320-0002a Proplus oven door side screws
Fig.5-11
Fig.5-12
Page 22
18
Hotplate
Part Finish Recommended Cleaning Method
Hob top (including burner heads
and caps)
Enamel or stainless steel
Hot soapy water, soft cloth. Any stubborn stains remove gently with
a nylon scourer.
Ceramic/Induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.
Griddle plate (some models only) Non-stick surface
Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.
Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Outside of Cooker
Part Finish Recommended Cleaning Method
Door, door surround and storage
drawer exterior
Enamel or paint
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
Stainless steel
E-cloth (electrical retailers) or microbre all-purpose cloth
(supermarket).
Sides and plinth Painted surface Hot soapy water, soft cloth.
Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.
Control panel
Paint, enamel, glass or stainless
steel
Warm soapy water. Do not use proprietary cleaners other than
washing-up liquid, as this may cause cosmetic damage. Do not use
abrasive cleaners on lettering.
Control knobs/handles & trims
Plastic/chrome, copper or
lacquered brass
Warm soapy water, soft cloth.
Brass Brass polish.
Oven door glass/glass lid (some
models only)
Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Oven and Grill
Part Finish Recommended Cleaning Method
Sides, oor & roof of oven NOT
COOK & CLEAN OVEN PANELS (see
below)
Enamel
Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW
MANUFACTURER’S INSTRUCTIONS.
Do not allow contact with the oven elements.
Cook & Clean oven panels (some
models only)
Special enamel that partly
cleans itself
This surface cleans itself at 200 °C and above, or the panels can be
removed and washed with hot soapy water and a nylon brush.
Oven shelves, Handyrack, Grill trivet,
Handygrill rack (some models only)
Chrome
An oven interior cleaner that is suitable for chrome. Soap lled pad.
Dishwasher.
Grill pan/meat tin (some models
only)
Enamel Hot soapy water. Soap lled pad. Dishwasher.
Table 5-1
Cleaning Table
Cleaners listed (Table 5-1) are available from supermarkets or
electrical retailers as stated.
For enamelled surfaces use a cleaner that is approved for use
on vitreous enamel.
Regular cleaning is recommended. For easier cleaning, wipe
up any spillages immediately.
Page 23
19
Hotplate ignition or hotplate burners faulty
Is the power on? Is the clock illuminated?
If not, there maybe something wrong with the power
supply.
Are the sparker (ignition electrode) or burner slots
blocked by debris?
Are the burner trim and caps correctly located? See the
section on ‘Cleaning’.
Remember that each cooktop burner has a special ame
supervision device (FSD) that stops the ow of gas if
the ame goes out. When lighting a cooktop burner the
safety device has to be overridden by holding in the
control knob so that the gas can ow. This allows the
ame sensor to heat up and operate the safety device.
Keep holding the knob pressed in to let the gas through
to the burner for few seconds. The igniter should spark
and light the gas.
If, when you let go of the control knob, the burner goes
out, the safety device has not held in. Turn the control to
the o position and wait one minute, then try again this
time holding in the control knob for slightly longer.
Hotplate burners will not light
Make sure that the burner parts have been replaced
correctly after wiping or removing for cleaning.
Check that there is not a problem with your gas
supply. You can do this by making sure that other gas
appliances you may have are working.
Do the burners spark when you push the button?
If not, verify that the power is on by checking that the
clock is illuminated.
Steam is coming from the oven
When cooking foods with high water content (e.g. oven
fries) there may be some steam visible at the rear grille.
Take care when opening the oven door, as there may
be a momentary pu of steam when the oven door
is opened. Stand well back and allow any steam to
disperse.
A crack has appeared in the ceramic warming zone
surface
Disconnect the cooker immediately from the power
supply and arrange for its repair. Do not use the cooker
until after the repair.
My ceramic warming zone is scratched
Always use the cleaning methods recommended in this
guide, and make sure that the pan bottoms are smooth
and clean.
Marks from mineral deposits from water or food can be
removed with a cleaning cream. However, tiny scratches
6. Troubleshooting
are not removable but will become less visible in time as
a result of cleaning.
Metal markings on the ceramic warming zone surface
Do not slide aluminium or copper pans across the
ceramic surface. Marks from aluminium and copper
pans as well as mineral deposits from water or food can
be removed with a suitable cleaning cream.
What cleaning materials are recommended for the
cooker?
See the ‘Cleaning’ section for recommended cleaning
materials.
Never use caustic or abrasive cleaners as these will
damage the surface.
An oven fan is noisy
The note of the oven fan may change as the oven heats
up – this is perfectly normal.
The knobs get hot when I use the oven or the grill. Can I
avoid this?
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open.
Make sure that the grill pan is pushed right back to the
‘back stop’ when grilling.
Always grill with the grill compartment door open.
If there is an installation problem and I don’t get my
original installer to come back to x it who pays?
You do. Service organizations will charge for their call
outs if they are correcting work carried out by your
original installer. It is in your interest to track down your
original installer.
Power failure
In the event of a failure in the electrical supply,
remember to reset the clock to make sure that the
timed oven continues to operate.
Fascia illumination is not coming on
Is the power on?
The appliance has developed a fault that cannot be
rectied by the user. Please contact your installer or a
qualied repair engineer.
Food is cooking too slowly, too quickly, or burning
Cooking times may dier from your previous oven.
Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide. The oven control settings and cooking
times are intended to be used only as a guide.
Individual tastes may require the temperature to be
altered either way, to get the results you want.
Page 24
20
Oven not coming on
Is the power on? Is the clock illuminated? If not, there
may be something wrong with the power supply.
Is the cooker supply on at the isolator switch?
Has the time of day been set?
Is the key symbol [F] showing in the display to signify
that the oven is locked? See the ‘Clock’ section of the
instructions for more information on the key lock
feature.
The oven is not cooking evenly
Do not use a baking tray with dimensions larger than
those specied in the section on ‘General Oven Tips’.
If you are cooking a large item, be prepared to turn it
round during cooking.
If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, make sure that it is placed centrally on the
shelf.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held rmly
against the seal.
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level arrange for
your supplier to level it for you.
The timed oven is not coming on when automatic cooking
Has the oven knob been left in the OFF position by
mistake?
Is the oven locked (see above)?
Oven temperature getting hotter as the cooker gets older
If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be tted by a service person.
An oven light is not working
The bulb has probably burnt out. You can buy a
replacement bulb (which is not covered under the
warranty) from a good electrical shop. Ask for a 15 W –
230 V lamp, FOR OVENS. It must be a special bulb, heat
resistant to 300 °C (Fig.6-1).
Before removing the existing bulb, turn o the power
supply and make sure that the oven is cool. Open the
oven door and remove the oven shelves.
Unscrew the bulb cover by turning counter-clockwise. It
may be very sti (Fig.6-2).
Taking care to protect your ngers with a glove in case
the bulb should shatter, unscrew the old bulb.
Screw in the new bulb; screw back the bulb cover. Turn
on the circuit breaker and check that the bulb now
lights.
ArtNo.324-0005 Oven light bulb
Fig.6-1
ArtNo.320-0020 Oven back fixing screws
ArtNo.324-0007 Unscrewing the bulb cover
Fig.6-2
Page 25
21
The oven door is misaligned
The bottom hinge of either oven door can be adjusted
to alter the angle of the door (Fig.6-3). Loosen the
bottom hinge xing screws and use the notch and a at
bladed screwdriver to move the position of the hinge to
set the hinge position (Fig.6-4).
Retighten the hinge screws.
Fig.6-3
ArtNo.320-0007 Oven door hinge adjustment 2
Fig.6-4
Eect of hinge adjustment – exaggerated for clarity
Oven door omitted for clarity
Centre line of hinge pin
Page 26
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
22
Dear Installer
Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.
Safety Requirements and Regulations
This cooker must be installed in accordance with
the relevant instructions in this booklet, with the
relevant national and local regulations, and with
the local gas and electricity supply companies’
requirements.
This cooker is a Class 2 Subclass 1 appliance.
Before installation, make sure that the cooker is
suitable for your gas type and supply voltage. See
the data badge.
The appliance must be installed in accordance with
the regulations in force and only in a well-ventilated
space.
Read the instructions before installing or using this
appliance.
In your own interest and that of safety, it is law
that all gas appliances be installed by competent
persons. Failure to install the appliance correctly
could invalidate any warranty or liability claims and
lead to prosecution.
This appliance can be converted for use on another
gas.
Provision of Ventilation
This appliance is not connected to a combustion products
evacuation device. Particular attention shall be given to the
relevant requirements regarding ventilation.
All rooms require a window that can be opened, or
equivalent, while some rooms require a permanent vent in
addition to the window.
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.
This appliance is designed for domestic cooking only. Use
for any other purpose could invalidate any warranty or
liability claim.
Note: An appliance for use on LPG must not be installed
in a room or internal space below ground level, e.g. in a
basement.
Conversion
This appliance is supplied set for G20 20 mbar.
Cat II
2H3+
.
A conversion kit for another gas is available for the cooker.
If the appliance is to be converted to another gas we
recommend that this is carried out before installation.
After converting the appliance, please attach the Gas
Conversion sticker over the appropriate area of the data
badge – this will identify the gas type for which the appliance
is now set.
You will need the following equipment to complete the
cooker installation satisfactorily:
• Stability bracket: If the cooker is to be supplied with
gas through a flexible hose, a stability bracket or chain
MUST be fitted.
These are not supplied with the cooker but are
available at most builders’ merchants.
• Gas pressure tester/manometer.
• Flexible gas hose: Must be in accordance with the
relevant standards.
• Multimeter: For electrical checks.
7. Installation
ArtNo.050-0011 - Installer information table
Installer’s Name
Appliance Serial Number
Installer’s Telephone Number
Installer’s Company
Page 27
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
23
You will also need the following tools:
1. Electric drill
2. Masonry drill bit (only required if tting the cooker on a
stone or concrete oor)
3. Wall plugs (only required if tting the cooker on a stone
or concrete oor)
4. Steel tape measure
5. Cross head screwdriver
6. Flat head screwdriver
7. Spirit level
8. Pencil
9. Adjustable spanner
10. Screws for tting stability bracket
11. 4 mm & 3 mm Allen keys
12. 13 mm spanner or socket wrench
3 pan supports Plinth
Griddle Grill pan & trivet
ArtNo.330-0001 - Grill pan
4 at shelves Handyrack
ArtNo.324-0003 Handyrack
Roasting tin
ArtNo.324-0004 Roasting tin
Checking the Parts:
Page 28
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
24
130 mm
ArtNo.110-0069 - 110DF - Lidded min spacings
75 mm
min
75 mm
min
650 mm
min
905 mm
min
930 mm
max
Fig.7-1
Positioning the Cooker
Fig.7-1and Fig.7-2 show the minimum recommended
distance from the cooker to nearby surfaces.
The cooker should not be placed on a base.
The hotplate surround should be level with, or above, any
adjacent work surface.
A gap of 75 mm should be left between each side of the
cooker ABOVE the hotplate level and any adjacent vertical
surface.
For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25 mm.
A minimum space of 650 mm is required between the top of
the hotplate and a horizontal combustible surface.
*Any cookerhood should be installed in accordance with the
hood manufacturer’s instructions.
**Any splashback must be tted in accordance with the
manufacturers instructions. Allowance should be made for the
additional height of the ue trim, which is tted to the cooker
hob.
Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration.
We cannot accept responsibility for damage caused by
normal use of the cooker to any material that de-laminates
or discolours at temperatures less than 65°C above room
temperature
We recommend a gap of 1110 mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.
If the cooker is near a corner of the kitchen a clearance of
130 mm is required to allow the oven doors to open (Fig.7-3).
The actual opening of the doors is slightly less but this allows
for some protection of your hand as you open the door.
Moving the Cooker
On no account try and move the cooker while it is
plugged into the electricity supply.
The cooker is very heavy, so take great care.
We recommend that two people manoeuvre the cooker.
Make sure that the oor covering is rmly xed, or removed,
to prevent it being disturbed when moving the cooker
around.
To help you, there are two levelling rollers at the back, and
two screw-down levelling feet at the front.
Remove the polystyrene base pack. From the front, tilt
the cooker backwards and remove the front half of the
polystyrene base (Fig.7-4). Repeat from the back and remove
the rear half of the polystyrene base.
Fig.7-4
ArtNo.110-0047 - 110 Clearances #2
410 mm min
1100 mm min*
**
Fig.7-2
Fig.7-3
Page 29
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
25
Stability chain
ArtNo.070-0014 - Stability bracket - Wall fitting
Cooker
Stability bracket
Floor
3 mm min
Typical oor mounting
Cooker
Outer stability
bracket
Floor
Wall
3 mm min
Typical wall mounting
ArtNo.010-0004 Moving the cooker
Lowering the Two Rear Rollers
To adjust the height of the rear of the cooker, rst t a 13 mm
spanner or socket wrench onto the hexagonal adjusting
nut (Fig.7-5). Rotate the nut – clockwise to raise – counterclockwise to lower.
Make 10 complete (360°) turns clockwise.
Make sure you lower BOTH REAR ROLLERS.
Completing the Move
Unfold the rear edge of the cardboard base tray. Open the
grill door and right-hand oven door so that you can get a
good grip on the bottom of the fascia panel as you move the
oven (Fig.7-6).
Carefully push the cooker backwards o the base tray.
Remove the base tray.
Position the cooker close to its nal position, leaving just
enough space to get behind it.
DO NOT use the door handles or control knobs to
manoeuvre the cooker.
Fitting the Stability Bracket or Chain
Unless otherwise stated, a cooker using a exible gas
connector must be secured with a suitable stability device.
Suitable stability devices are shown in Fig.7-7, Fig.7-8 and
Fig.7-9.
If you are using a stability chain (Fig.7-7) then the chain
should be kept as short as is practicable and xed rmly to
the rear of the cooker.
If you are using a stability bracket (Fig.7-8 and Fig.7-9), then
adjust the bracket to give the smallest practicable clearance
between the bracket and the engagement slot in the rear of
the cooker.
Fit the bracket so that it engages as far as possible over the
chassis of the cooker.
Repositioning the Cooker Following
Connection
If you need to move the cooker once it has been connected
then you need to unplug it and, having gripped under the
fascia panel and lifted the front of the cooker slightly
(Fig.7-6), you need to check behind the cooker to make sure
that the gas hose is not caught.
As you progress, make sure that both the electricity cable and
gas hose always have sucient slack to allow the cooker to
move.
With a stability chain tted, release it as you ease the cooker out.
Do not forget to ret it when you replace the cooker.
When you replace the cooker, again check behind to make
sure that the electricity cable and gas hose are not caught or
trapped.
Fig.7-6
Fig.7-7
Fig.7-8
Fig.7-5
Fig.7-9
Page 30
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
26
Gas Connection
This must be in accordance with the relevant standards.
The exible hose (not supplied with the cooker) must be
in accordance with the relevant standards. Hoses may be
purchased at most builders’ merchants.
The gas supply needs to terminate with a down-facing
bayonet.
The connector is located just below the hotplate level at the
rear of the cooker. If in doubt contact your supplier.
The rear cover boxes limit the position of the supply point.
Because the height of the cooker can be adjusted and
each connection is dierent, it is dicult to give precise
dimensions.
Although a 900 mm hose can be used, a 1250 mm hose
will allow slightly more exibility in the positioning of the
bayonet and make moving the cooker easier.
The hose should be tted so that both inlet and outlet
connections are vertical so that the hose hangs downwards in
a ‘U’ shape.
Ideally the hose supply connection should be within the
shaded area ‘A’ (Fig.7-10).
For Natural Gas, the exible hose must be in accordance with
BS 669. For LP Gas, it should be capable of 50 mbar pressure,
70 °C temperature rise, and carry a red stripe, band or label. If
in doubt contact, your supplier.
Screw connect the threaded end of the hose into the gas
inlet.
After completing the gas connection, make sure that the
cooker is gas sound with a pressure test.
Pressure Testing
The gas pressure can be measured at one of the hotplate
burner injectors (not a wok burner).
Lift o a burner head. Fit the pressure gauge to the injector.
Turn on and light one of the other hotplate burners.
Turn on the control knob for the burner with the pressure
gauge tted to let gas through.
See the data badge for test pressures.
Turn o the burners. Make sure that you reassemble the
burner top in the correct way on the burner body.
Electrical Connection
This appliance must be installed by a suitably qualied
electrician to comply with the relevant electrical regulations,
and also the local electricity supply company requirements
A
400
600
200
300
Position for gas
supply connector
Gas inlet
connector
Fig.7-10
Page 31
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
27
Current Operated Earth Leakage Breakers
The combined use of your cooker and other domestic
appliances may cause nuisance tripping, so we
recommend that the cooker is protected on an individual
RCD (Residual Current Device) or RCBO (Residual Current
Breaker with Overload).
IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED
ELECTRICIAN.
WARNING: THIS APPLIANCE MUST BE EARTHED.
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double-pole
switch, having a contact separation of at least 3 mm in all
poles.
The cooker MUST NOT be connected to an ordinary
domestic power point.
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect
the mains cable to the correct terminals for your electrical
supply type (Fig.7-11 and Fig.7-12). Check that the links are
correctly tted and that the terminal screws are tight. Secure
the mains cable using the cable clamp.
Final Checks
Hotplate Check
Check each burner in turn (refer to the ‘Hotplate Burners’
section at the front of the instructions).
Grill Check
Turn on the grill control and check that the grill heats up.
Oven Check
Set the clock as described earlier in the instructions, and then
turn on the ovens. Check that the oven fan starts to turn and
that the ovens start to heat up.
Note: The oven light bulb is not included in the guarantee.
Turn o the oven.
Fitting the Plinth
Oer the keyhole slots on the outer plinth to the location
points on the inner plinth (Fig.7-13). When released the outer
plinth should automatically adjust to the oor height.
WARNING: When moving the cooker ensure that the
outer plinth is removed. Failure to do so may result
in damage to plinth and oor.
Customer Care
Installer: Please complete your details in this guide, inform
the user how to operate the cooker and hand over the
instructions.
Thank you.
ArtNo.130-0010 Electrical connections single-phase
L
N
230 V ac 50 Hz
10 mm² max
6 mm² max
L1
N
L3
L2
3N ac
230/400 V 50 Hz
6 mm² max
10 mm² max
6 mm² max
Fig.7-11
Fig.7-13
Fig.7-12
Page 32
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.
28
A
B
C
ArtNo.311-0010 Injectors
Fig.8-1
A – Jet, B – Internal injector, C – External injector
Check the ‘Technical Data’ section at the back of the book
that the hob is convertible to the gas you want to use.
A suitably competent person must perform the conversion.
After conversion the installation must comply with the
relevant regulations and also the local electricity supply
company requirements. Read the instructions before
converting this appliance.
Failure to convert the appliance correctly could
invalidate any warranty or liability claims and lead
to prosecution.
When servicing or replacing gas-carrying
components disconnect from the gas supply before
starting operation. Check the appliance is gas sound
after completion.
DO NOT use reconditioned or unauthorised gas
controls.
Disconnect from the electricity and gas supply
before servicing.
Before electrical reconnection, check that the
appliance is electrically safe.
Hotplate
Injectors
Remove the burner caps and heads. Remove the old jets
(Fig.8-1). Fit the new jets (see the ‘Technical Data’ section at
the back of this book for the correct jets). Reassemble in the
reverse order.
Tap Adjustment
Removing the Control Panel
Pull o all the control knobs and remove the xing screws
underneath the control panel.
The control panel will drop down slightly. It is held at the top
by two holes in the top edge, one at each end, that locate on
the tags on the inner panel (Fig.8-2). Lift the control panel
clear of the tags and pull forwards, taking care not to damage
or strain the wiring.
Bypass Screw Adjustment
Turn the bypass screw on each control clockwise to the stop
(Fig.8-3).
Ret the control panel.
Affix Label
Stick the appropriate gas label over the natural gas part of the
appliance data label.
8. Conversion to LP Gas
ArtNo.0102-0011 - Screwing
the control valve bypass screw
Fig.8-3
Fig.8-2
Page 33
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.
29
Pressure Testing
Connect the appliance to the gas supply.
Check the appliance is gas sound.
The gas pressure can be measured at one of the hotplate
injectors (not a wok burner).
Lift o a burner head. Fit the pressure gauge to the jet. Turn
on and light one of the other burners. Turn on and press in
the control knob for the burner with the pressure gauge
tted.
The pressure should be 29 mbar for Butane and 37 mbar for
Propane. After checking the pressure, turn o the taps and
replace the burner head.
Reassemble burner top, making sure it is reassembled in the
correct way on the burner body.
Check operation of all the burners.
Page 34
30
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
9. Circuit Diagram
P095199
1
2
P2
P1
E
1
2
1
2
a
b
e
f
c
d
12
P095199
1
2
P2
P1
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
br
br
br
br
bk
bk
y
y
y
y
or
v
r
w
w
w
v
v
r
r
r
br
r
r
r
b
br
r
br
b
or
v
v
v
br
r
r
y
y
y
w
w
w
b
b
br
br
v
v
bk
bk
v
r
r
r
b
br
br
br
v
br
b
r
v v
v
v
v
b
b
b
br
A
A1
K
L
B1
H
N1
N2
C
D2
D3
F1
F2
J
G1 G2
D4
B3
B4
B5
P057904
1
2
P2
P1
D1
P1
P2
P3
1
2
4
3
5
P038482
B
M1 M2
M3
A2
A3 A4
I
B2
N3
Code Colour
b Blue
br Brown
bk Black
or Orange
r Red
v Violet
w White
y Yellow
g/y Green/yellow
gr Grey
Code Description
A Illumination board - left-hand side
A1 Grill front switch
A2 Grill energy regulator
A3 Left-hand grill element
A4 Right-hand grill element
B Illumination board - right-hand side
B1 Left-hand oven thermostat
B2 Left-hand front switch
B3 Left-hand oven top inner element
B4 Left-hand oven top outer element
B5 Left-hand oven bottom element
F1 Left-hand oven thermal preset
C Clock
D1 Right-hand oven thermostat
D2 Right-hand oven front switch
D3 Right-hand oven element
Code Description
D4 Right-hand oven fan
F2 Right-hand oven thermal preset
G1 Left-hand oven light
G2 Right-hand oven light
H Cooling fan
I Illumination switch
J Ignition switch
K Oven light switch
L Spark generator
M1 Grill heat indicator
M2 Left-hand oven heat indicator
M3 Right-hand oven heat indicator
N1 Warming zone front switch
N2 Warming zone indicator neon
N3 Warming zone Element
Page 35
31
10. Technical Data
THE COOKER IS CATEGORY: Cat II
2H3+;
Cat II
2E3+;
Cat II
2E3BP.
It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.
COUNTRY OF DESTINATION: GB, IE, FR, NL, DE, SE, BE, AT, LU, CH.
Connections
Gas (Rp ½ at rear right-hand side) Electric
Natural gas 20 mbar
230/400 V 50 HzButane 29 mbar
Propane 37 mbar
See the appliance badge for test pressures.
Dimensions
Overall height minimum 905 mm maximum 930 mm
Overall width 1092 mm
Overall depth 600 mm to fascia; 650 mm over handles
Minimum space above the hotplate 650 mm
Refer to 'Positioning the Cooker'.
Ratings
Hotplate Bypass Screw*
Natural Gas 20 mb L.P. Gas
Injector Injector
Wok burner 57
3.5 kW
internal 78
3.5 kW (246 g/h)
internal 53
external 126 external 82
Large burner 40
3.0 kW 134 3.0 kW (210 g/h) 87
Medium burner 32 1.7 kW 109 1.7 kW (119 g/h) 68
Small burner 28 1.0 kW 75 1.0 kW (70 g/h) 51
* The valves in this cooker are fitted with adjustable bypass screws. The cooker is supplied with the bypass screws set for
Natural gas. For LPG conversion the bypass screws must be screwed all the way down.
Oven Efficiency
Ovens
Left-hand Oven Right-hand Oven
Conventional Forced Air Convection
Maximum power output @ 230 V 50 Hz
2.2 kW 2.5 kW
Energy eciency class on a scale of A (more ecient) to G (less ecient) A A
Energy consumption based on standard load 0.99 kWh 0.90 kWh
Usable volume (litres) 76 69
Size Large Large
Time to cook standard load 40 minutes 38 minutes
Surface area of the grid
1400 cm
2
1400 cm
2
Grill 2.3 kW
Warming zone 160 W
Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.): 7.3 kW.
ArtNo.107-0024 - Technical data - 110DF - Classic-Toledo
Page 36
32
Notes
Page 37
33
Notes
Page 38
34
Notes
Page 39
CONSUMER SERVICE
If you have any product enquiries, or in the event of a problem
with your appliance once it has been installed, please
telephone 0870 789 5107.
CONSUMER SERVICE LINES OPEN:
Monday to Thursday 8amÐ6pm
Friday 8amÐ5pm
Saturday 9amÐ1pm
WARRANTY
Your manufacturer warranty covers goods of our own brand
for defective workmanship and materials for a period of 3 year
from the date of purchase. This warranty covers mechanical
breakdown and proven cosmetic and manufacturing defects.
To register for this guarantee simply fill in and return the
FREEPOST registration form provided. Alternatively call free on
0800 694 4170, quoting reference FAGX91AN or register
online at www.falconappliances.co.uk
Any damage, blemishes or chips identified upon receipt of the
product must be reported within 90 days – proof of purchase
may be required to establish validity. Scratches on the surface
of ceramic hobs must be reported within 14 days. Scratches
caused by usage are not covered. Accidental damage is not
covered by the manufacturer's warranty.
For warranty compliance, the requirements are that the
appliance:
¥ Has been correctly installed in accordance with current
legislation, relevant British and European Standards
and Codes of Practice, by a suitably competent person
registered with Gas Safe or equivalent body and, where
applicable, a qualified electrician.
¥ Has been used solely for domestic cooking purposes.
¥ Is in use in the UK*, has not been taken abroad as a
personal export. (In the Republic of Ireland conditions
may vary, so consult your retailer.)
¥ Is not second-hand or a refurbished appliance. The
manufacturer's warranty is not transferable.
¥ Has not been subject to misuse, accidental damage or
modification, and has not deteriorated due to normal
domestic wear and tear, and the manufacturer's
recommendations concerning cleaning materials have
been followed.
¥ Has not been repaired by persons or organisations
other than those authorised to act on behalf of AGA
Rangemaster.
Exceptions:
¥ Items not included under the free 3 year guarantee
include pan supports, griddles, wok rings, baking
trays, grill pans, trivets, filters, light bulbs and other
consumable accessories.
¥ Any damage caused other than through normal use.
¥ Breakdowns associated with cooking spillage.
¥ Cosmetic deterioration deemed to be normal wear and
tear.
This warranty is in addition to your Statutory Rights.
* Only certain models can be adapted for use with Mains Gas
supplied in the Channel Islands and Isle of Man.
OUT OF WARRANTY
We recommend that Falcon appliances are serviced regularly
throughout their life to maintain optimum performance
and efficiency. Service work should only be carried out by
technically competent and suitably qualified personnel.
For your own safety, always make sure that work is carried
out by a Gas Safe registered engineer for gas appliances or an
approved electrician for electrical models.
For a competitive quote and to arrange for a Falcon approved
engineer to attend, call Consumer Services on: 0870 789 5107.
SPARE PARTS
To maintain optimum and safe performance, we recommend
that only genuine Falcon spare parts are used. These are
available from most major spares stockists, including ourselves.
Contact Consumer Services on 0870 789 5107, who will be
happy to help.
STANDARDS
Falcon cookers are designed and manufactured to a recognised
international quality standard, which meets the requirements
of BS EN ISO 9001, BS EN ISO 14001 and OHSAS 18001 for
continually improving environmental procedures.
Falcon cookers comply with the essential requirements of the
appropriate European Directives, and carry the CE mark.
Name of Appliance & Colour*
Appliance Serial Number*
Fuel Type*
Natural Gas
LP Gas
Dual Fuel Electric
Retailer's Name & Address
Date of Purchase
Installer's Name & Address
Installer's Telephone Number
Date of Installation
* This information is on the appliance data badge Ð look in the
appliance instructions to find out where the data badge is located.
Page 40
Falcon Appliances
Clarence Street
Royal Leamington Spa
Warwickshire
CV31 2AD
Tel 0870 755 6490
Fax 0192 631 1032
Email consumers@falconappliances.co.uk
www.falconappliances.co.uk
Trade Enquiries 0115 946 6143
Email sales@falconappliances.co.uk
Registered in England and Wales. Registration No. 354715 Registered Office: Juno Drive, Leamington Spa, Warwickshire, CV31
3RG
Falcon continuously seeks improvements in specification, design and production of products and thus, alterations take place
periodically. Whilst every effort is made to produce up-to-date literature, this booklet should not be regarded as an infallible
guide to current specification, nor does it constitute an offer for the sale of any particular appliance.
For over 45 years
Divertimenti, Falcon’s
sister company, has
been the ultimate destination
for food lovers and serious
chefs alike. With its vast array
of cookware, tableware and
kitchenware, Divertimenti
caters to all your culinary needs.
With over 4500 items on the
Divertimenti
website www.divertimenti.co.uk
Loading...