Falcon Dominator Plus G3151, Dominator Plus G3151D, Dominator Plus G3150 Installation And Servicing Instructions

DOMINATOR

PLUS

G3151 Fusion Range
G3150 Fusion Boiling Top

INSTALLATION and
SERVICING INSTRUCTIONS

This appliance must be installed and serviced by a competent person as stipulated by the
Gas Safety (Installation & Use) Regulations.

IMPORTANT

The installer must ensure that the installation of the appliance is in conformity with these instructions
and National Regulations in force at the time of installation. Particular attention MUST be paid to:

Gas Safety (Installation & Use) Regulations
Health And Safety At Work etc. Act
Local and National Building Regulations
Fire Precautions Act

Detailed recommendations are contained in
Institute of Gas Engineers published documents:
IGE/UP1, IGE/UP/2
BS6173 and BS5440

The appliance has been CE-marked on the basis of compliance with the Gas Appliance Directive for
the Countries, Gas Types and Pressures as stated on the data plate.

WARNING: TO PREVENT SHOCKS, ALL APPLIANCES WHETHER GAS OR ELECTRIC,

MUST BE EARTHED.

On completion of the installation, these instructions should be left with the Engineer-in-Charge for
reference during servicing. Further to this, The Users Instructions should be handed over to the User,
having had a demonstration of the operation and cleaning of the appliance.

IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE INSTALLING
AND COMMISSIONING THIS APPLIANCE. FAILURE TO COMPLY WITH THE SPECIFIED
PROCEDURES MAY RESULT IN DAMAGE OR THE NEED FOR A SERVICE CALL.

PREVENTATIVE MAINTENANCE CONTRACT

In order to obtain maximum performance from this unit we would recommend that a maintenance
contract be arranged with SERVICELINE. Visits may then be made at agreed intervals to carry out
adjustments and repairs. A quotation will be given upon request to the contact numbers below.

WEEE Directive Registration No. WEE/DC0059TT/PRO

At end of unit life, dispose of appliance and any replacement
parts in a safe manner, via a licenced waste handler.
Units are designed to be dismantled easily and recycling of all
material is encouraged whenever practicable.

Falcon Foodservice Equipment

HEAD OFFICE AND WORKS

Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.

SERVICELINE CONTACT

Phone: [phone] Fax: [phone]

T100850 Ref. 2

IMPORTANT INFORMATION
Warranty Policy Shortlist

Warranty does not cover :-

• Correcting faults caused by incorrect installation of a product.

• Where an engineer cannot gain access to a site or a product.

• Repeat commission visits.

• Replacement of any parts where damage has been caused by misuse.

• Engineer waiting time will be chargeable.

• Routine maintenance and cleaning.

• Gas conversions i.e. Natural to Propane gas.

• Descaling of water products and cleaning of water sensors where softeners/ conditioners are not fitted,
or are fitted and not maintained.

• Blocked drains

• Independent steam generation systems.

• Gas, water and electrical supply external to unit.

• Light bulbs

• Re-installing vacuum in kettle jackets.

• Replacement of grill burner ceramics when damage has been clearly caused by misuse.

• Where an engineer finds no fault with a product that has been reported faulty.

• Re-setting or adjustment of thermostats when unit is operating to specification.

• Cleaning and unblocking of fryer filter systems due to customer misuse.

• Lubrication and adjustment of door catches.

• Cleaning and Maintenance

• Cleaning of burner jets

• Poor combustion caused by lack of cleaning

• Lubrication of moving parts

• Lubrication of gas cocks

• Cleaning/adjustment of pilots

• Correction of gas pressure to appliance.

• Renewing of electric cable ends.

• Replacement of fuses

• Corrosion caused by use of chemical cleaners.

Model kW Btu/hr
Open Top 5.3 20,000
Fusion Burner (Nat Gas) 7.5 28.100
Fusion Burner (Propane) 5.5 20,600
900mm Oven 7.1 26,700

SECTION 1 - INSTALLATION

UNLESS OTHERWISE STATED, PARTS WHICH HAVE BEEN PROTECTED BY THE MANUFACTURER
ARE NOT TO BE ADJUSTED BY THE INSTALLER.

1.1 MODEL NUMBERS, NETT WEIGHTS

and DIMENSIONS

Model

Width

(mm)

Depth

(mm)

Height

(mm)

Weight

(kg)

G3151
Fusion Range

900 770 890 129

G3151D
Fusion Range

600 770 890 129

G3150
Fusion Boiling Top

900 770 455 70

1.2 SITING

The appliance should be installed on a level, fireproof
surface, in a well lit and draught free position.

If the floor is constructed of combustible material, then
local fire requirements should be checked to ensure
compliance. A clear space of 150mm should be left
between rear and side of unit and any combustible wall.

Important

If a unit is to be installed in suite formation with other
matching appliances, the instructions for all models must
be consulted to determine the necessary clearances to
any combustible rear wall or overlying surface. Some
models require greater clearances than others and the
largest figure quoted in individual instructions will
therefore determine the clearance for the complete suite
of adjoining appliances.

The oven flue discharges vertically through hob
rear. There must be no direct connection of flue to
any mechanical extraction system or to the outside
air. Open top burners discharge combustion products
directly into the room.

Care should be taken not to disturb the air
combustion admission nor the combustion products
evacuation of appliances fitted with open burners.

1.3 VENTILATION

Adequate ventilation must be provided to supply
sufficient fresh air for combustion and allow easy
removal of combustion products which may be
harmful to health. Recommendations for Ventilation of
Catering Appliances are given in BS5440:2.

For multiple installations the requirements for
individual appliances should be added together.
Installation should be made in accordance with local
and/or national regulations applying at the time. A
competent installer MUST be employed.

1.4 GAS SUPPLY

The incoming service must be of sufficient size to supply
full rate without excessive pressure drop.

A gas meter is connected to the service pipe by gas
supplier. Any existing meter should be checked by
supplier to ensure it is of adequate capacity to pass
required rate for appliance in addition to any other gas
equipment installed.

Installation pipe work should be fitted in accordance with
IGE/UP/2. The pipe work should be of adequate size but
not smaller than unit gas inlet connection, ie. Rp¾
(¾” B.S.P.). An isolating cock must be located close by
to allow shut-down during an emergency or servicing.

If flexible tube is used, the gas supply tubing or hose shall
comply with national requirements in force. These will be
periodically examined and replaced as necessary.

The installation must be tested for gas tightness.
Procedure details can be found in IGE/UP/1.

The adjustable governor supplied must be fitted to
natural gas appliances.

1.5 ELECTRICAL SUPPLY

Not applicable to this appliance.

1.6 WATER SUPPLY

Not applicable to this appliance.

1.7 HEAT INPUTS - NATURAL and PROPANE

GAS (kW net & Btu/hr gross)

1.7.1 Total Inputs

Model kW Btu/hr
G3151/D (Nat Gas) 41.4 154,250
G3151/D (Propane) 39.1 146,750
G3150 (Nat Gas) 34 127,600
G3150 ( Propane) 32 120,100

1.7.2 Individual Inputs (kW nett & Btu/hr gross)

1.8 INJECTOR DIAMETERS

Model Natural Propane
Open top Ø1.93mm Ø1.2mm
Fusion Burner Ø1.0 mm Ø 0.5mm
Ovens Ø2.2mm Ø 1.33mm

1.8.1 Fusion Burner pilot Injectors

Natural Gas Propane Gas
G27.2 G22.1

1.9 GAS PRESSURE ADJUSTMENT
NATURAL and PROPANE GAS

The following supply pressures apply to both all units.

Gas type mbar
Natural 20
Propane 37

Pressure test point is located on RH side of gas
manifold situated behind the front control panel.

An adjustable governor (¾ BSP) is provided on Natural
gas units.. This should be adjusted to achieve an
operating pressure at control manifold of 15mbar.
For muti-burner systems, approximately half of the

burners should be on when setting governor pressure.

1.10 BURNER ADJUSTMENTS NATURAL and

PROPANE GAS.

1.10.1 Burner Aeration

Open top, fusion and oven burners are fitted with fixed
injectors and set aeration apertures.. NO
ADJUSTMENT is possible.

1.10.2 Bypass Screw Diameters

Minimum gas flow to burner is governed by size of
fixed by-pass screw hole as follows:-

Natural Gas Propane Gas

Model

Marked Marked
Open Top 76 51
Oven 93 55

The fusion burner has no bypass screw.

SECTION 2 - ASSEMBLY and

COMMISSIONING

Fixings

2.1 ASSEMBLY
Note

The following paragraphs should be read as applicable
to the unit being assembled.

a) Unpack appliance and place it in position using feet

adjusters to level appliance.

b) Units with castors should be fitted with accessories

supplied according to separate instructions provided.

c) Open oven door, pull out shelves and base panel.

Check burner spark igniter arrangements are correctly
located and secured. Ensure ALL packing, etc. is
removed from oven. Replace all parts in reverse
sequence.

d) Check open top and remove tape, packing, etc. from

hob area and ensure that all burners and pan supports
are secured in position. The open top burner heads fit
loosely upon aluminium bases of lift-off construction.

2.1.1 Fryplate Accessory

If fryplate (Figure 2) is supplied, refer to user instructions
for details. Important note: this should be operated on a
low flame setting only.

2.1.2 Flue Accessory

A tall flue is available as an accessory that may be
substituted for standard type supplied with unit.
Details of the alteration process are indicated in Figures
3 through 6.
Remove hob as detailed in Sections 3.2.2 and 3.2.3.
Undo and remove fixings at locations shown in Figure 3.
Remove fixings at rear detailed in Figure 4.
Install replacement flue as detailed in Figure 5
and secure using existing fixings at hob and rear at
positions indicated in Figures 5 and 6.

Important Note: It is not possible to fit a
splashplate / plateshelf to a unit fitted with a tall flue.

Figure 2

Figure 3

Figure 4

Figure 5

Figure 6

Fixings

Fixings

Fixings

2.2 CONNECTION TO GAS SUPPLY

Connect appliance to gas supply and ensure that the
governor supplied is fitted on NATURAL gas installations.
Test for gas tightness.

The integral gas supply downstream of gas valve may be
checked by applying leak detection spray with burner lit.
Appliance inlet connection terminates at upper rear
RH side in Rp¾ (¾" BSP female).

2.3 CONNECTION TO ELECTRICAL SUPPLY

Not applicable to these appliances.

2.4 CONNECTION TO WATER SUPPLY

Not applicable to these appliances.

2.5 COMMISSIONING THE APPLIANCE
Important

Prior to operation, ensure that ALL packing material has
been removed.

2.5.1 Setting the Gas Pressure

a) It is necessary to check gas pressure during

commissioning and a suitable gauge must be
connected to test point on RH side of supply manifold

(situated behind front control facia).
b) Turn on main gas valve at supply to unit.
c) Light three open top burners as detailed in Section

2.5.3. Gas supply pipes may contain air so repeat

procedure until burner lights.
d) Adjust governor (Natural gas installations only) at unit

rear to relevant pressure setting found in Section 1.9.

To increase pressure - turn screw clockwise

(or anti-clockwise to decrease). Check again after

15 minutes of operation.
e) Disconnect gauge. Replace test point sealing screw

and test for gas tightness.

2.5.2 Checking Performance of the Controls

a) Light open top or oven as detailed in Section 2.5.3.

Check ignition is smooth and without delay.

Repeat operation several times.
b) Place a thermocouple at oven centre and select 210°C

setting. Allow oven to heat up and check temperature

is 210°C (+/-10°C). If reading is outwith specified

range, the thermostat may be faulty. In this case, unit

should be serviced (see thermostat replacement and

calibration procedure). Turn gas supply to oven OFF

and allow a sufficient cool-down period before

removing thermostat.

2.5.3 Lighting Sequence
Important

Prior to operation, ensure ALL packing material has been
removed from appliance.

Open Top

1.

Ensure mains gas is turned on.

2.

To light hob burners, press knob and turn to full flame

position. Ignite burners using taper or match. Hold in
knob for 20 seconds and then release. Burner will
remain lit. Turn knob to required position.

Oven

1.

Ensure mains gas is turned on.

2.

Open oven doors.

3.

Turn thermostat knob to maximum setting and push in.

This will establish a flow of gas to oven burner.

4.

Continue to press knob in and at the same time, push
piezo spark ignitor button situated on control panel to
provide a spark at oven burner. Press at 1 sec intervals
for 8 times only.

5.

Having established burner flame, maintain pressure on

knob for a further 20 seconds before release.

6.

Burner should remain lit. Should burner fail to remain
lit, wait 3 minutes then return to Step 2 and repeat
ignition procedure.

7.

When burner remains lit, turn thermostat to required
temperature setting.

To Shut Oven OFF

To extinguish oven flame, turn thermostat to OFF
position.

2.6 INSTRUCTION TO USER

The installer must ensure that user thoroughly
understands the instructions for lighting, cleaning and
correct use of unit. It is also important to ensure that
gas isolating cock location is known to user and that the
procedure to follow in event of emergency is
demonstrated.

SECTION 3 ­SERVICING AND CONVERSION

Important

BEFORE ATTEMPTING ANY SERVICING, ENSURE
ISOLATING COCK IS TURNED OFF AND CANNOT BE
INADVERTENTLY TURNED ON. AFTER ANY
MAINTENANCE TASK, CHECK APPLIANCE TO
ENSURE THAT IT PERFORMS CORRECTLY AND
CARRY OUT ANY NECESSARY ADJUSTMENTS AS
DETAILED IN SECTION 1.

After carrying out any servicing or exchange of gas
carrying component.

ALWAYS CHECK FOR GAS TIGHTNESS!

3.1 GAS CONVERSION CHECK LIST

For All Appliances

CHANGE INJECTORS
CHANGE BY-PASS SCREW AND SET LOW RATE .
Refer to Section 1.10.
CHANGE DATA PLATE

Ensure gas supply is disconnected before commencing.
Only reconnect gas supply after all conversion work has

been completed.

Natural to Propane

Remove governor from appliance inlet pipe-work.

Propane to Natural

Fit governor to appliance inlet pipe-work and follow
details in Section 2.5.

3.1.2 Open Top Low setting
Screw - To Replace
(Figure 7)

a) Remove control panel.
b) Unscrew and remove existing low position screw
from open top tap.
c) Insert replacement screw into open top tap and

secure. Repeat for all taps.

d) Refit control panel.

3.1.3 Oven Burner - To Replace Injector

a) Remove oven shelves and base plate.
b) Disconnect Gas supply pipe.
c) Unscrew and remove existing injector.
d) Insert and screw in replacement injector.

e) Re-connect Gas supply pipe.

3.1.4 Thermostat - To Replace Bypass Screw
(Figure 7)

a) Remove control panel.
b) Unscrew and remove existing bypass screw from

thermostat.

c) Insert replacement bypass screw and secure into

thermostat.

d) Re-assemble in reverse order.

3.1.1 Open Top Burners - To Replace Injector

(Figure 8)

a) Remove pan supports.
b) Remove burner heads and burner bezels.
c) Remove pressed hob by pulling upwards.(Do not

remove screws in hob.)

d) Leaving injector holders in situation, unscrew existing

injectors.
e) Remove injectors.
f ) Insert replacement injectors and secure. Repeat for all

taps
g) Refit removed parts.

Open top low setting
screw

Thermostat bypass screw

Figure 7

Open top injector

Figure 8

3.1.5 Solid Top Burner - To Replace Injector

(Figure 9)

a) Remove solid top castings.
b) Release pilot assembly from burner.
c) Remove burner.
d) Unscrew and remove existing injector.
e) Insert and screw in replacement injector.
f) Refit burner and ensure burner aeration adjustment.
(see Section 1.10)

Pilot injector

a

) Remove pilot pipe from pilot assembly.
b) Remove existing pilot injector from pilot pipe.
c) Fit replacement injector over pipe

d) Refit pilot pipe to pilot assembly.

e) Refit pilot assembly to burner.
f) Leave solid top castings off to allow manometer to be

fitted to burner test point.

3.1.6 Resetting Low Rate Screw (Figure 10)

a) Remove control panel.
b) Fit manometer to burner test point.
c) Connect replacement gas supply to appliance.
d) Light solid top burner.
e) While burner is ignited turn solid top tap to the low

flame position.

f ) Turn screw until manometer reading is stated in the

table indicated in Section 1.10.2.
g) Refit control panel.
h) Remove manometer from burner test point, ensuring

no gas leaks. Reassemble solid top castings.

Ensure data plate with correct information is fitted
after conversion.

3.2 REMOVAL OF CONTROL PANELS

Various panels are removed as follows:

3.2.1 To Remove Facia Panel

Remove control knob(s). Open oven doors and undo
fixings along underside and top. Pull facia panel forward
while slightly easing bottom edge upward to remove.

3.2.2 To Remove Open Top Hob Components

Remove pan supports and burner heads complete with
aluminium bezels and venturi that sit loosely upon
injector holder.
The hob is retained by ballstud fixings at each corner.
Lift hob clear to access burner support brackets.

3.2.3 To Remove Hob

Remove fixings that secure front hob support and fixings
that secure flue to back panel. Lift full hob area ­including flue - clear of unit.

3.3 REMOVAL OF DROP-DOWN DOOR

Open door completely and insert a suitable pin into
marked hole on both hinges.

Hinge hole

The action of closing door will result in the hinge pulling
out of bracket to allow door to be removed.

Due to hinge springs being under tension, do not disturb
pins while door is removed from range.

Replace in reverse order.

3.4 BURNERS

3.4.1 Open Top

Remove hob components as Section 3.2.2.
Undo burner pipe compression fitting.
Undo injector holder fixings.
Withdraw burner body.
Replace in reverse order.

3.4.2 Oven

Open oven doors and remove base panel.
Undo Gas connection.
Remove tie wrap, pull back insulated
sleeving and disconnect igniter lead at
spark electrode end.
Undo FFD thermocouple at burner.
Undo fixings that secure burner feet to base panel.
Remove oven burner.
Replace in reverse order, ensuring correct dimensions for
Spark electrode and FFD Thermocouple. (fig 12)

3.5 CLEANING

3.5.1 Burners

Burners should be cleaned daily to maintain
maximum performance. Open top burners should be
cleaned as detailed in User Instructions. Additional
burners are best cleaned with a wire brush; port blockage
should be freed using a metal broach, any loose material
being shaken out via burner shank.

Ensure burners are
dry and free from any
cleaning material
before replacing.

Check adjustment as
detailed in Section 1.

Figure 9

Solid top pilot pipe

Solid top low flame
adjustment screw

Solid top burner test point

3.5.2 Injectors

Injectors are best cleaned with a wooden splinter or soft
fuse wire. Metal reamers may distort or increase orifice
size and their use should be avoided.

3.6 THERMOCOUPLES and

FLAME FAILURE DEVICE (FFD)

3.6.1 Open Top Flame Failure Device Magnet Unit

To remove and replace FFD magnet unit, the following
procedures must be followed. Isolate Gas supply.
Remove hob components as detailed in Section 3.2.2.
Undo FFD thermocouple at rear of tap, undo FFD section
at tap rear and withdraw.
Replace in reverse order.

3.6.2 Open Top Thermocouple

Remove hob as detailed in Section 3.2.2.
Remove nut that secures thermocouple to burner
support bracket and pull thermocouple through support
bracket from underside.
Undo thermocouple connection at FFD section of gas tap
and carefully remove thermocouple.
Replace in reverse order, taking care to position tip
correctly in relation to burner ports. Thermocouple
tip should be 35mm above support bracket. Ensure
thermocouple does not touch any part of burner when
fully re-assembled. (Fig 11)

3.6.3 Oven Flame Failure Device Magnet Unit

The oven FFD magnet unit is an integral thermostat part.
Remove hob components as detailed in Section 3.2.2
to gain access to FFD. Isolate Gas supply.
Undo FFD thermocouple at thermostat rear. Undo rear
FFD section and withdraw. Replace in reverse order.

Figure 12

3.6.4 Oven Thermocouple
To Remove Thermocouple

Remove facia panel as detailed in Section 3.2.1.
Remove hob fitments. See Sections 3.2.2 or 3.2.3
as required.
Remove RH side panel.
Undo thermocouple nut at thermostat rear.
Open over doors. remove shelves and base plate.
Undo nut that secures thermocouple to burner
bracket. Remove sensor from burner bracket.
Release thermocouple from clips in oven chamber.
Remove Thermocouple by feeding through slot in oven
side panel. Replace in reverse order, taking care not
to over tighten, ensure side wall insulation around
thermocouple access slot is undamaged then ensuring
position as indicated in Figure 12.

3.7 OVEN IGNITERS and ELECTRODES

Igniter is piezo spark type and contains no batteries.
Unit comprises piezo spark igniter, lead and electrode
assembly. Lead and earth lead are push-fit at igniter
end. Oven igniter electrode, Thermocouple, and burner
ports should be aligned as indicated in Figure 12.

3.7.1 Oven Igniter

Remove facia panel as detailed in Section 3.2.1.
Disconnect igniter earth wire and .
Pull back insulated sleeve and remove igniter lead
connection from spark igniter.

Undo nut that secures igniter in position. Remove
Igniter. Replace in reverse order,

3.7.2 Oven Electrode

Remove oven shelves and base plate.
Remove tie wraps and pull back
insulated sleeve.

Disconnect igniter lead from electrode.
Undo fixing that secures electrode to burner bracket.
Remove electrode and replace in reverse order ensuring
position is as indicated in Figure 12.

Note: Care should be taken not to damage electrode
Important: if spark is present but burner will not light,
ensure gas is present and dimensions are as (Fig 12)

Figure 11

3.8 OVEN THERMOSTAT

Remove control knobs and fascia panel as
detailed in Section 3.2.1.
Remove hob fitments as detailed in Sections 3.2.2 and

3.2.3 as appropriate.
Undo thermocouple connection at thermostat rear.
Disconnect oven burner pipe.
From inside oven, release clips that secures thermostat
capillary to oven side wall. Undo fixings that secure
thermostat to manifold.
Remove thermostat by carefully feeding capillary and
phial through crown plate.
Replace all parts in reverse order. Renew manifold
gasket if necessary.

3.8.1 Thermostat Calibration

The thermostat should not be calibrated. If temperature is
outwith specified tolerances, replace thermostat and
return faulty thermostat to Falcon Quality Department.

3.9 OPEN TOP and SOLID TOP GAS TAPS
Note
Plugs and bodies are machined in pairs and are
therefore not interchangeable. Always clean one tap
at a time.

3.9.1 Service - Isolate from gas supply.

Remove control knobs and fascia panel as detailed
in Section 3.2.1.

Remove fixings from front of tap body. Withdraw spindle
and niting arrangement to allow plug to be eased out.
Clean gas tap plug with a soft rag and regrease using an
approved high temperature lubricant. Take care not to
over-grease as surplus may cause gasway blockage.
Replace parts in correct order and check gas tightness.

3.9.2 Removal – isolate from gas supply.

Remove control knobs and fascia panel as detailed
in Section 3.2.1.

Remove hob fitments as detailed in Sections 3.2.2 and

3.2.3 as appropriate.
Disconnect thermocouple connection at gas tap rear.

3.10 GOVERNOR (Natural Gas Models Only)

The governor supplied is maintenance free. Check
that blue dust cap is covering vent and in good
condition as this protects the breather hole.

When checking for gas leaks around governor, be
aware that unburned gas may be vented occasionally
to release pressure on diaphragm. This should not be
confused with a gas leak.

3.11 FAULT CHECK LIST
If a flame is not established on any burners (hob or
oven), follow this check list.

1.

Check mains gas is ON.

2.

Check pressure at test point to ensure gas is flowing to

unit.

3.

If pressure does not register then check governor is
fully operational or check for line blockage.

4.

If gas is present, check burner injector for blockage.

5.

If injector is OK then check FFD is engaging and
passing gas.

6.

OVEN ONLY - Check for spark at spark electrode.

7.

OVEN ONLY - If there is no spark then check spark
d i m e n s i o n s ( f i g 1 2 ) and HT lead connections.
Also check igniter.

8.

OVEN ONLY – Note: Spark may be present but will still
not light burner unless dimensions relative to burner
are as Fig 12.

Note: If after adjusting the electrode to the correct
dimensions (fig 12), a spark is not present, or is
present but will not light burner, check the following:

Check Spark lead and return earth wire connections at
piezo spark igniter body.

Check for clean contact between burner fixing feet and
oven base, using spring washers under screw heads.

9.

If flame is still not present, then re-check from start.

If flame is established but not maintained, follow
this check list.

1.

Check thermocouple is positioned correctly in burner
flame. (fig 12) Burner ports must be clean.

2.

Check thermocouple is not damaged and is secured
to gas valve FFD section to allow FFD to energise.

3.

Check FFD is energising and maintaining flame.

4.

If, after carrying out the above, burner is still not
maintaining flame then re-check from start.

SECTION 4 - SPARES and

ACCESSORIES

When ordering spare parts, always quote appliance type
and serial number.

This information will be found on data badge attached to
base plate.