Falcon CLA90EI5BL-CH, CLA90EI5CR-CH, CLA90EI5CY-CH User Manual

USER GUIDE &
INSTALLATION INSTRUCTIONS
Classic & Professional+
90 Induction
Australia
U110695-02A
SLOW BAKED LEG OF LAMB
INGREDIENTS
2-3 large sprigs of rosemary
4 large garlic cloves cut in half lengthways
1.8 kg leg of lamb
8 good quality anchovy llets, halved
100 ml olive oil
250 ml dry red wine
Maldon salt and freshly ground black pepper
METHOD
1. Preheat the oven to 220 °C (for a conventional oven), 200 °C (for a
fan oven) or gas mark 7.
2. Pull the small sprigs o the rosemary branches and set aside with the garlic.
3. Using the tip of a paring knife, make up to 20 well-spaced cuts into the esh of the lamb, about 2.5 cm inch deep. Divide the rosemary sprigs, garlic and anchovies and push down into the cuts. Place the leg on a large roasting tin and pour over the oil, massaging it all over the joint. Season well with salt and pepper and pour the wine and 250 ml water into the tin.
4. Put into the oven and sear for 15 minutes, then turn the temperature right down to 130 °C (conventional oven), 110 °C (fan oven) or gas mark 1 and roast for 4-5 hours, basting every 30minutes or so. Basting frequently helps to keep the meat moist and encourages the build up of a good glaze on the outside. Add more liquid (wine or water) if the tin looks dry Ð there should always be liquid in the tin throughout this cooking process.
5. The meat is ready when it starts to fall o the bone, at which point it should have a core temperature of 90 °C. Remove from the oven, transfer to a warmed carving dish, cover loosely with foil and leave to rest in a warm place for 30-45 minutes before carving.
6. Pour the juices from the tin into a tall hi-ball glass and allow to settle. Spoon the fat from the top of the glass. There should be enough sticky, reduced juices for an intense gravy hit if not, pour the juices you have back into the roasting tin and put it over the heat, pour in a splash of water or wine and deglaze the tin scraping up all the sticky bits from the base. Boil fast until syrupy, taste and correct the seasoning.
RASPBERRY SOUFFLÉ
INGREDIENTS
400 g raspberries
1 tbsp lemon juice
100 g caster sugar
2 tsp créme de framboise
1 tsp cornour
180 g egg whites (about 6)
Pinch of cream of tartar or a squeeze of lemon juice
Icing sugar for dusting
METHOD
1. For the soué, press the raspberries through a ne sieve to
2. Put 45 g of the sugar in a separate pan. Melt it and then boil until it becomes a thick syrup (121°C on a sugar thermometer). To test without a thermometer, dip a teaspoon into the syrup and then dip quickly into cold water. You should be able to roll the cooling syrup into a ball between your ngers. Be careful as the syrup is extremely hot. When it has reached the right point, stir the hot syrup into the raspberry jam.
3. Mix the framboise and cornour together and stir into the jam over the heat. Turn the jam into a small bowl, sprinkle the surface with icing sugar and cover with cling lm.
4. Preheat the oven (not grill) to 180 °C shelf level 2 (conventional oven), 160 °C (fan oven) or gas mark 4 centre shelf.
5. Whisk the egg whites with the cream of tartar until you can
form soft peaks, then fold in the remaining caster sugar. Lightly fold the whites into the jam, leaving thin traces of white visible in the mixture.
6. Spoon into four large buttered and sugared ramekins, place these on a baking tray and bake for 10 minutes.
7. Dust with icing sugar.
Contents
1. Before you start... 1
Personal safety 1 Electrical connection safety 1 Peculiar smells 2 Ventilation 2 Maintenance 2 Induction care 3 Oven care 4 Hob care 5 Grill/glide-out grill™ care 5 Cooling fan 5 Cooker care 5 Cleaning 5
2. Cooker Overview 6
The Hob 6 The Glide-out Grill 10 The Ovens 11 Operating the Ovens 11 Main Oven Light 11 Accessories 12
3. 2 Button - rotary clock 13
4. 3-button clock 16
5. Cooking Tips 18
7. Cleaning your cooker 20
8. Troubleshooting 24
9. Installation 27
Service and Spares 27 Safety Requirements and Regulations 28 Provision of Ventilation 28 Location of Cooker 28 Positioning the Cooker 29 Moving the Cooker 29 Fitting the Stability Bracket 30 Repositioning the Cooker Following
Connection Levelling the Cooker 30 Electrical Connection 31 Final Checks 33 Final Fitting 33 Customer Care 33
30
10. Servicing 34
1. Panels 34
2. Hotplates 34
3. Controls 34
4. Grill 35
5. Ovens 35
6. Doors 37
6. Cooking table 19
Classic & Professional+ 90 Induction
11. Circuit Diagrams 39
12. Technical Data 41
i
ii

1. Before you start...

This User Guide covers a number of dierent models. Although some of the illustrations will look dierent to your particular model, the functions will be the same.
Your cooker should give you many years of trouble-free cooking if installed and operated correctly. It is important that you read this section before you start.

Personal safety

This appliance is for cooking purposes only. It must not be used for other purposes, for example heating a room. Using it for any other purpose could invalidate any warranty or liability claim. Besides invalidating claims this wastes fuel and may overheat the control knobs.
This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children less than 8 years of age should be kept away unless continuously supervised. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
The cooker should not be placed on a base.
This appliance is designed for domestic cooking only.
Use for any other purpose could invalidate any warranty or liability claim.
Before operating the ovens please refer to the oven shelf installation, in the Accessories section.
The appliance and its accessible parts become hot during use and will retain heat even after you have stopped cooking. Care should be taken to avoid touching heating elements.
A long term cooking process has to be supervised from time to time. A short term cooking process has to be supervised continuously.
• DANGER OF FIRE: DO NOT store items on the cooking surfaces.
• ALWAYS keep combustible materials, e.g. curtains, and flammable liquids a safe distance away from your cooker.
• DO NOT spray aerosols in the vicinity of the cooker while it is on.

Electrical connection safety

This cooker must be installed in accordance with the relevant instructions in this booklet, with the relevant national and local regulations, and with the local electricity supply companies’ requirements.
WARNING: THE APPLIANCE MUST BE EARTHED
Note: The cooker must be connected to the correct electrical supply as stated on the voltage label on the cooker, through a suitable cooker control unit incorporating a double-pole switch, having a contact separation of at least 3 mm in all poles.
Read the instructions before installing or using this appliance.
This appliance is heavy so take care when moving it.
The cable size and type should be suitable for the
Electrical Load of the appliance and comply with the relevant national and local requirements.
The cooker may be installed in a kitchen/kitchen diner but NOT in a room containing a bath or shower.
This appliance MUST be earthed.
The cooker MUST NOT be connected to an ordinary
domestic power point.
It is normal for the hob control display to flash for about 2 seconds during first power setting.
Set the clock to make sure that the oven is functional – see the relevant section in this manual.
The appliance must be installed in accordance with the regulations in force and only in a well ventilated space.
Failure to install the appliance correctly could invalidate any warranty or liability claims and lead to prosecution.
• DO NOT install the appliance on a platform.
To avoid overheating, DO NOT install the cooker behind
a decorative door.
Accessible parts will become hot during use and will retain heat even after you have stopped cooking. Keep babies and children away from the cooker and never wear loose-fitting or hanging clothes when using the appliance.
• DO NOT use a steam cleaner on your cooker.
• DO NOT manouvre the cooker while it is plugged into
the electricity supply.
Before electrical reconnection, check that the appliance is electrically safe.
1

Peculiar smells

When you rst use your cooker it may give o an odour. This should stop after use.
Before using your cooker for the rst time, make sure that all packing materials have been removed and then, to dispel manufacturing odours, turn all the ovens to 200°C and run for at least an hour.
Before using the grill for the rst time you should also turn on the grill and run for 30 minutes with the grill pan in position, pushed fully back and the grill door open.
Make sure the room is well ventilated to the outside air (see ‘Ventilation’ below). People with respiratory or allergy problems should vacate the area for this brief period.
• DO NOT use unstable saucepans. ALWAYS make sure that you position the handles away from the edge of the hotplate.
• NEVER leave the hotplate unattended at high heat settings. Pans boiling over can cause smoking, and greasy spills may catch on fire. Use a deep fat thermometer whenever possible to prevent fat overheating beyond the smoking point.
Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.
• NEVER leave a chip pan unattended. ALWAYS heat fat slowly, and watch as it heats. Deep fry pans should be only one third full of fat.

Ventilation

The use of a cooking appliance results in the production of heat and moisture in the room in which it is installed. Make sure that the kitchen is well ventilated. Keep natural ventilation holes open or install a powered cooker hood that vents outside.
Prolonged intensive use of the appliance may call for additional ventilation, for example opening a window, or more eective ventilation, for example increasing the level of mechanical ventilation where present.

Maintenance

Only a qualied service engineer should service the appliance and only approved spare parts should be used. It is recommended that this appliance is serviced annually.
Before replacing the bulb, turn o the power supply and make sure that the oven is cool.
• DO NOT use cooking vessels on the hotplate that overlap the edges.
• ALWAYS allow the cooker to cool and then switch it off at the mains before cleaning or carrying out any maintenance work, unless specified otherwise in this guide.
• NEVER try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool. Filling the pan too full of fat can cause spill over when food is added. If you use a combination of oils or fats in frying, stir them together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan. Carefully watch for spills or overheating of foods when frying at high or medium high temperatures.
• DO NOT use the top of the flue (the slots along the back of the cooker) for warming plates, dishes, drying tea towels or softening butter.
• DO NOT use water on grease fires and never pick up a flaming pan. Turn the controls off and then smother a flaming pan on a surface unit by covering the pan completely with a well fitting lid or baking tray. If available, use a multi-purpose dry chemical or foam­type fire extinguisher.
• DO NOT modify this appliance. This appliance is not intended to be operated by means of external timer or separated remote-control system.
If flammable materials are stored in the drawer, oven(s) or grill(s) it may explode and result in fire or property damage.
• DO NOT use the control knobs to manoeuvre the cooker.
• NEVER operate the cooker with wet hands.
• DO NOT use a towel or other bulky cloth in place of a
glove – it might catch fire if brought into contact with a hot surface.
• DO NOT use hotplate protectors, foil or hotplate covers of any description. These may affect the safe use of your hotplate burners and are potentially hazardous to health.
• NEVER heat unopened food containers. Pressure build up may make the containers burst and cause injury.
• ALWAYS allow any cookware to cool before cleaning.
2

Induction care

ArtNo.312-0003 Moving pans
• IMPORTANT INFORMATION FOR PACEMAKER AND IMPLANTED INSULIN PUMP USERS: The functions of
this hob comply with the applicable European standards on electromagnetic interference. If you are fitted with a pacemaker or implanted insulin pump and are concerned please consult your doctor for medical advice.
When the hob is in use keep magnetic items away, such as credit and debit cards, floppy disk, calculators, etc.
• To fully utilise the power of your induction hob and to ensure longevity of performance, we recommend the use of AGA Rangemaster Induction cookware. If you decide to purchase an alternative set of cookware for use on your induction cooker, we would strongly recommend that composite aluminium pans with steel inserts, example shown Fig. 1.1, are avoided. This type of pan construction can significantly reduce the lifetime and performance of your induction cook top.
Take care when touching the marked cooking areas of
the hob.
Fig. 1.2
Fig. 1.1
Fig. 1.3
Use adequately sized pans with flat bottoms that are
large enough to cover the surface of the hotplate heating area. The use of undersized pans will expose a portion of the surface unit to direct contact and may result in the ignition of clothing.
Only certain types of glass, glass-ceramic, earthenware or other glazed containers are suitable for use on the warming zone; others may break because of the sudden change in temperature.
Only certain types of glass, glass-ceramic, earthenware or other glazed containers are suitable for hotplate cooking; others may break because of the sudden change in temperature. NEVER cook directly on the hob surface (Fig. 1.2).
Only certain types stainless steel, enamelled steel pans or cast iron pans with enamelled bases are suitable for induction hob cooking.
Take care NOT to scratch the surface when placing cookware on the glass panel.
• DO NOT leave the hob zones switched on unless being used for cooking.
Fig. 1.4
• DO NOT stand or rest heavy objects on the hob.
Although the ceramic surface is very strong, a sharp blow or sharp falling object (e.g. a salt cellar) might cause the surface to crack or break (Fig. 1.3).
Should a crack appear in the surface, disconnect the appliance immediately from the supply and arrange for its repair.
• ALWAYS LIFT pans off the hob. Sliding pans may cause marks and scratches (Fig. 1.4).
3
ArtNo.312-0001 Not cooking surface
Fig. 1.5
ArtNo.090-0007 90 Ceramic: oven steam out the back
Fig. 1.6
Take care NOT TO PLACE HOT LIDS onto the hob
surface (Fig. 1.5). Lids that have been used to cover a hot pan can “stick” or create a “vacuum” effect to the Glass Hob. Should this occur, DO NOT attempt to lift the lid off the glass surface, this may damage the glass. Instead slide the lid to the edge of the hob surface and remove, taking care not to scratch the hob surface. Alternatively wait until the lid has cooled to room temperature, the vacuum has been released, then remove the lid by lifting it from the hob surface.
• DO NOT place anything between the base of the pan and the hob surface (e.g. asbestos mats, aluminium foil, wok stand).
Take care NOT to place metallic objects such as knives, forks, spoons and lids on the hob surface since they can get hot.
Fig. 1.7
ArtNo.324-0001 Steam burst
We recommend that you avoid wiping any surface unit areas until they have cooled and the indicator light has gone off. Sugar spills are the exception to this (see ‘Cleaning your Cooker’). After cleaning, use a dry cloth or paper towel to remove any cleaning cream residue.
The ceramic surface should be washed after use in order to prevent it from becoming scratched or dirty. However, you should clean the hob with caution as some cleaners can produce noxious fumes if applied to a hot surface.
• DO NOT leave the hob unattended. Care should be taken to not allow your cookware to boil dry. It will damage your cookware and Induction Glass Hob.
After use, switch off the hob element by its control. DO NOT rely on the pan detector.

Oven care

When the oven is not in use and before attempting to clean the appliance ALWAYS be certain that the control knobs are in the OFF position.
Use oven gloves to protect your hand from potential burns.
Cooking high moisture content foods can create a ‘steam burst’ when the oven door is opened (Fig. 1.6). When opening the oven, stand well back and allow any steam to disperse.
The inside door face is constructed with toughened safety glass. Take care NOT to scratch the surface when cleaning the glass panel.
Accidental damage may cause the door glass panel to fracture.
Keep oven vent ducts unobstructed.
• DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.
4
Make sure the shelves are pushed firmly to the back of the oven. DO NOT close the door against the oven shelves.
• DO NOT use aluminium foil to cover shelves, linings or the oven roof.
When the oven is on, DO NOT leave the oven door open for longer than necessary, otherwise the control knobs may become very hot.
• DO NOT use the timed oven if the adjoining oven is already warm.
• DO NOT place warm food in the oven to be timed.
• DO NOT use a timed oven that is already warm.

Cooker care

As steam can condense to water droplets on the cool outer trim of the oven, it may be necessary during cooking to wipe away any moisture with a soft cloth. This will also help to prevent soiling and discolouration of the oven exterior by cooking vapours (Fig. 1.7).

Cleaning

Isolate the electricity supply before carrying out any thorough cleaning. Allow the cooker to cool.
In the interests of hygiene and safety, the cooker should be kept clean at all times as a build up in fats and other food stuff could result in a fire.
Use dry oven gloves when applicable – using damp gloves might result in steam burns when you touch a hot surface.

Hob care

• NEVER allow anyone to climb or stand on the hob.
• DO NOT use the hob surface as a cutting board.
• DO NOT leave utensils, foodstus or combustible items
on the hob when it is not in use (e.g. tea towels, frying pans containing oil).
• DO NOT place plastic or aluminium foil, or plastic containers on the hob.
• ALWAYS turn the control to the OFF position before removing a pan.
Avoid heating an empty pan. Doing so may damage both the hob and pan.

Grill/glide-out grill™ care

When using the grill, make sure that the grill pan is in position and pushed fully in, otherwise the control knobs may become very hot.
• DO NOT leave the grill on for more than a few moments without the grill pan underneath it, otherwise the knobs may become hot.
• NEVER close the grill door when the grill is on.
Accessible parts may be hot when the grill is in use.
Young children should be kept away.
Clean only the parts listed in this guide.
Clean with caution. If a wet sponge or cloth is used to
wipe spills on a hot surface, be careful to avoid steam burns. Some cleaners can produce noxious fumes if applied to a hot surface.
• NEVER use paint solvents, washing soda, caustic cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt.
• DO NOT mix different cleaning products – they may react together with hazardous results.
All parts of the cooker can be cleaned with hot soapy water.
Take care that no water seeps into the appliance.
Before you remove any of the grill parts for cleaning,
make sure that they are cool or use oven gloves.
• DO NOT use any abrasive substances on the grill and grill parts.
• DO NOT put the side runners in a dishwasher.
• DO NOT put the burner heads in a dishwasher.
• NEVER use caustic or abrasive cleaners as these will
damage the surface.
• DO NOT use steel wool, oven cleaning pads or any other materials that will scratch the surface.
• NEVER store flammable materials in the drawer. This includes paper, plastic and cloth items, such as cookbooks, plastic ware and towels, as well as flammable liquids.

Cooling fan

This appliance may have a cooling fan. When the grill or oven is in operation the fan will run to cool the fascia and control knobs.
• DO NOT store explosives, such as aerosol cans, on or near the appliance.
• DO NOT use steel wool, oven cleaning pads, or any other materials that will scratch the surface.
• DO NOT attempt to disassemble or clean around any burner while another burner is on, otherwise an electric shock could result.
5
A
B
C
D
E

2. Cooker Overview

ArtNo.025-0005 - Overview - 90 induction - 2 button clock & GO grill
Fig. 2.1
The 90 induction cooker (Fig. 2.1) has the following features:
Fig. 2.2
Fig. 2.3
A. 5 induction cooking zones
B. A control panel
C. A separate Glide-out Grill™
D. Main, programmable fan oven
E. Tall fan oven

The Hob

Use only pans that are suitable for induction hobs. We recommend stainless steel, enamelled steel pans or cast iron pans with enamelled bases. Note that some stainless steel pans are not suitable for use with an induction hob so please check carefully before purchasing any cookware.
Pans made of copper, aluminium or ceramic are not suitable for use on an induction hob. The kind of pan you use and the
quantity of food aects the setting required. Higher settings are required for larger quantities of food.
Pots and pans should have thick, smooth, at bottoms (Fig. 2.2). This allows the maximum heat transfer from the hob to the pan, making cooking quick and energy ecient. Never use a round-bottomed wok, even with a stand.
The very best pans have bases that are very slightly curved up when cold (Fig. 2.3). If you hold a ruler across the bottom you will see a small gap in the middle. When they heat up the metal expands and lies at on the cooking surface.
6
Make sure that the base of the pan is clean and dry to prevent any residue burning onto the hob panel. This also helps prevent scratches and deposits.
Always use pans that are the same size as (or slightly larger than) the areas marked on the hob. Using a lid will help the contents boil more quickly.
The induction hob comprises of ve cooking zones containing induction elements with dierent ratings and diameters (Fig. 2.4) each with a pan detector and residual heat indicator, and a hob control display.
Max: 1.85 kW Boost: 2.5 kW
Zone 1
Max: 1.85 kW Boost: 3.0 kW
Zone 3 Zone 5
Max: 1.85 kW Boost: 2.5 kW
Fig. 2.4
The hob control display (Fig. 2.5) informs you of the following induction hob functions:
Pan detector
H Residual heat indicator A Automatic heat-up
Child lock
L1/L2 Low temperature setting P Power boost setting
Pan Detector,
If a cooking area is switched on and there is no pan in place or if the pan is too small for the cooking area, then no heat
will be generated. The symbol [ ] will appear on the hob control display; this is the “pan-missing symbol”. Place a pan
of the correct size on the cooking area and the [ ] symbol will disappear and cooking can begin. After 10 minutes without detecting a pan the cooking zone will switch o automatically.
Table 2.1 shows the minimum pan sizes recommended for each cooking zone.
Note: Using pans with a base diameter smaller than those recommended will result in a power reduction.
Residual Heat Indicator, H
After use, a cooking zone will remain hot for a while as heat dissipates. When a cooking zone is switched o the residual heat indicator symbol [H ], will appear in the display. This shows that the cooking zone temperature is above 60 °C and may still cause burns. Once the temperature has dropped to below 60 °C the [H ] will go out.
Automatic Heat-up, A
This function is available on all of the cooking zones. It allows rapid heating up of the element to bring the selected cooking zone up to temperature. Once the zone is at the required cooking temperature the power level will reduce automatically to the preset level.
Zone 2
Max: 1.15 kW Boost: 2.0 kW
Cooking Zone
Front left 140
Rear left 180
Centre 180
Rear right 180
Front right 140
Table 2.1
Zone 4
Max: 1.15 kW Boost: 2.0 kW
Minimum Pan Diameter
(Pan Base) mm
Fig. 2.5
The function is selected by turning the control knob to the ‘A’ position. Turn the control knob momentarily counter­clockwise from the zero position until the symbol [ on the hob control display.
Once the [ of your choice (1 to 9). The pan will heat up at 100% power for a specied time before the power is reduced to the level selected.
A ] is displayed, turn the control knob to the level
A ] is shown
7
Fig. 2.6
Power level
1 0:48
2 2:24
3 3:50
4 5:12
5 6:48
6 2:00
7 2:48
8 3:36
9
Automatic heat-up time at
Table 2.2
100% (min:sec)
When the Automatic Heat-up function is activated, the hob control display will ash alternately between the [A ] setting and the chosen power level.
Once the Automatic Heat-up time has ended the hob display will stop ashing and will show the chosen power level.
The Automatic Heat-up function can be stopped by either turning the control knob back to the “0” power setting or turning the control knob to the “9” power setting.
For your guidance Table 2.2 shows the time available at 100% power depending on the power level selected in the Automatic Heat-up mode.
Child Lock,
IMPORTANT: The child lock can only be activated when all the cooking zones are switched o.
To prevent the unwanted use by children, the hob can be locked.
To lock the hob, simultaneously turn the two left-hand controls counter-clockwise (Fig. 2.6) and hold until the symbol appears in the centre of the hob control display (Fig.
2.7).
A ] will ash when locking the hob – this is normal.
Note: [
Fig. 2.7
Locking the hob will NOT aect the oven; it can still be used.
To unlock the hob, simultaneously turn the two left-hand controls counter-clockwise and hold until the disappears from the centre of the hob control display.
symbol
8
Low Temperature Setting, L1/L2
This function should only be used when heating
from cold
Each cooking area is equipped with 2 low temperature settings:
• L1 will maintain a temperature of about 40 °C – ideal for gently melting butter or chocolate.
• L2 will maintain a temperature of about 90 °C – ideal for simmering (bring the pan to the boil and then select L2 to keep soups, sauces, stews, etc at an optimal simmer).
The maximum time this setting can be used is 2 hours. To increase the heat, just turn the control knob to the required level. The maximum times for all other power levels are shown in Table 2.3.
Power Boost Setting, P
All of the induction cooking zones have Power Boost available, activated by turning the control knob clockwise until [P ] is shown on the hob control display.
Power Boost allows additional power to be made available for each of the cooking zones. This is useful to bring a large pan of water to the boil quickly.
Power Level
L1 and L2
1
2
3
ArtNo.051-0002 - Min pan diameter
4
5
6
7
8
9
Power Boost
A & B linked
A B
Maximum Operating Time
2 hours
6 hours
6 hours
5 hours
5 hours
4 hours
1.5 hours
1.5 hours
1.5 hours
1.5 hours
10 minutes
Table 2.3
C
Fig. 2.8
The Power Boost function operates for a maximum of 10 minutes on each zone, after which the power is automatically reduced to setting 9.
When using the Power Boost function, the cooking zones are linked.
Fig. 2.8 shows the hob layout. Zones A and B are linked together as are zones C, D and E.
This means that when using zone A on Power Boost and then switching zone B to Power Boost, the power to zone A will reduce slightly. The last zone switched to power boost always takes priority. Zones C, D and E work in the same way.
Deactivate the Power Boost function by turning the control knob to a lower setting.
Overheat Function
This function identies when the temperature of the pan rises rapidly and works to maintain a safe level of pan temperature. It should not interfere with normal cooking.
Cookware with bases that become distorted (Fig. 2.2) when heated may interfere with the operation of the Overheat Function. This may result in damage to your cookware or Induction Glass Hob.
D
E
Induction
C, D & E linked
Please read and follow the manufacturers’ instructions carefully before using cookware on your induction hob.
9
Fig. 2.9
Fig. 2.10
Fig. 2.11
ArtNo.331-0001Grill pan pulled forwards

The Glide-out Grill

CAUTION: This appliance is for cooking purposes
only. It must not be used for other purposes, for example room heating.
CAUTION: Accessible parts may be hot when the grill
is in use. Young children should be kept away.
Open the door and pull the grill pan carriage forward using the handle (Fig. 2.9 or Fig. 2.10 depending on model).
The grill has two elements that allow either the whole area of the pan to be heated or just the right-hand half.
Adjust the heat to suit by turning the knob. To heat the whole grill, turn the knob clockwise (Fig. 2.11).
To heat the right-hand half, turn the knob counter-clockwise. The neon indicator light by the grill control will come on.
For best results, leave the grill pan in the grill chamber and preheat the appropriate part(s) of the grill for two minutes. The grill trivet can be removed and the food placed on it while you are waiting for the grill to preheat.
DO NOT leave the grill on for more than a few
moments, without the grill pan underneath it, otherwise the knobs may become hot.
Fig. 2.12
Fig. 2.13
ArtNo.235-0007 - Classic
DL grill control
ArtNo.331-0002 Grill pan high/low position
1
Once the grill has preheated, take the grill pan out again and put the trivet back in place with the food on it. Slide the grill pan or carriage back into the grill chamber. Make sure that it is pushed right in.
The grill pan trivet in Fig. 2.9 can be turned over to give two grilling positions (Fig. 2.12).
The grill pan trivet in Fig. 2.10 can be turned to give four grilling positions (Fig. 2.13).
Never close the grill door when the grill is on.
2
3
4
10
ArtNo.320-0026
- Oven light

The Ovens

The clock must be set to the time of day before the ovens will work. See the following section on ‘The Clock’ for instructions on setting the time of day.
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed from the front of the appliance.
Fig. 2.14
Both ovens are fan ovens.
Fan ovens circulate hot air continuously, which means faster, more even cooking. The recommended cooking temperatures for a fan oven are generally lower than those for a non-fan oven.

Operating the Ovens

Turn the oven knob to the desired temperature (Fig. 2.14).
The oven indicator light will glow until the oven has reached the temperature selected (Fig. 2.15). It will then cycle on and o during cooking.
When cooking foods with high water content, there may be some steam visible at the grille at the rear of the hotplate. This is perfectly normal.

Main Oven Light

Press the button to turn the light on (Fig. 2.16).
If the oven light fails, turn o the power supply before changing the bulb. See the ‘Troubleshooting’ section for details on how to change the bulb.
ArtNo.235-0004 - Classic DL oven 1
ArtNo.235-0005 - Classic DL oven control 2
Fig. 2.15
Fig. 2.16
11
Loading...
+ 33 hidden pages