Falcon CLA110DFFBL-CHLPG, CLA110DFFBL-CH, CLA110DFFCR-CH, CLA110DFFCY-CH User Manual
USER GUIDE &
INSTALLATION INSTRUCTIONS
Classic
110 Dual Fuel
Australia
U110807-01A
SLOW BAKED LEG OF LAMB
INGREDIENTS
• 2-3 large sprigs of rosemary
• 4 large garlic cloves cut in half lengthways
• 1.8 kg leg of lamb
• 8 good quality anchovy llets, halved
• 100 ml olive oil
• 250 ml dry red wine
• Maldon salt and freshly ground black pepper
METHOD
1. Preheat the oven to 220 °C (for a conventional oven), 200 °C (for a
fan oven) or gas mark 7.
2. Pull the small sprigs o the rosemary branches and set aside with
the garlic.
3. Using the tip of a paring knife, make up to 20 well-spaced cuts into
the esh of the lamb, about 2.5 cm inch deep. Divide the rosemary
sprigs, garlic and anchovies and push down into the cuts. Place
the leg on a large roasting tin and pour over the oil, massaging it
all over the joint. Season well with salt and pepper and pour the
wine and 250 ml water into the tin.
4. Put into the oven and sear for 15 minutes, then turn the
temperature right down to 130 °C (conventional oven), 110 °C
(fan oven) or gas mark 1 and roast for 4-5 hours, basting every
30minutes or so. Basting frequently helps to keep the meat moist
and encourages the build up of a good glaze on the outside. Add
more liquid (wine or water) if the tin looks dry Ð there should
always be liquid in the tin throughout this cooking process.
5. The meat is ready when it starts to fall o the bone, at which point
it should have a core temperature of 90 °C. Remove from the oven,
transfer to a warmed carving dish, cover loosely with foil and leave
to rest in a warm place for 30-45 minutes before carving.
6. Pour the juices from the tin into a tall hi-ball glass and allow to
settle. Spoon the fat from the top of the glass. There should be
enough sticky, reduced juices for an intense gravy hit if not, pour
the juices you have back into the roasting tin and put it over the
heat, pour in a splash of water or wine and deglaze the tin scraping
up all the sticky bits from the base. Boil fast until syrupy, taste and
correct the seasoning.
RASPBERRY SOUFFLÉ
INGREDIENTS
• 400 g raspberries
• 1 tbsp lemon juice
• 100 g caster sugar
• 2 tsp créme de framboise
• 1 tsp cornour
• 180 g egg whites (about 6)
• Pinch of cream of tartar or a squeeze of lemon juice
• Icing sugar for dusting
METHOD
1. For the soué, press the raspberries through a ne sieve to
produce 180 g of purée. Put this into a heavy-bottomed pan,
add the lemon juice and reduce down to a thick jam, stirring
from time to time and being careful not to let it catch and burn.
2. Put 45 g of the sugar in a separate pan. Melt it and then boil
until it becomes a thick syrup (121°C on a sugar thermometer).
To test without a thermometer, dip a teaspoon into the syrup
and then dip quickly into cold water. You should be able to roll
the cooling syrup into a ball between your ngers. Be careful as
the syrup is extremely hot. When it has reached the right point,
stir the hot syrup into the raspberry jam.
3. Mix the framboise and cornour together and stir into the
jam over the heat. Turn the jam into a small bowl, sprinkle the
surface with icing sugar and cover with cling lm.
4. Preheat the oven (not grill) to 180 °C shelf level 2 (conventional
oven), 160 °C (fan oven) or gas mark 4 centre shelf.
5. Whisk the egg whites with the cream of tartar until you can
form soft peaks, then fold in the remaining caster sugar. Lightly
fold the whites into the jam, leaving thin traces of white visible
in the mixture.
6. Spoon into four large buttered and sugared ramekins, place
these on a baking tray and bake for 10 minutes.
7. Dust with icing sugar.
Contents
1. Before You Start... 1
Personal Safety 1
Electrical Connection Safety 1
If You Smell Gas 2
Peculiar Smells 2
Ventilation 2
Maintenance 2
Oven Care 3
Grill/Glide-out Grill™ Care 4
Cooling Fan 4
Cooker Care 4
Cleaning 4
2. Cooker Overview 5
Hotplate Burners 5
Wok Burner 6
The Wok Cradle (optional extra) 7
The Griddle 7
The Grill 8
The Ovens 9
Accessories 10
Storage 10
Glide-out Oven Shelf (optional) 11
3. 3 Button clock 12
7. Troubleshooting 20
8. Installation 22
Service and Spares 22
Safety Requirements and Regulations 23
Provision of Ventilation 23
Location of Cooker 23
Conversion 23
Positioning the Cooker 25
Moving the Cooker 26
Levelling 27
Fitting the Stability Bracket and Chain 27
Gas Connection 28
Pressure Testing 28
Final Fitting 31
Customer Care 31
9. Conversion to LP Gas 32
Conversion from Natural Gas (1.0 kPa)
to LPG X Propane (2.54 kPa)
Injectors 32
Tap Adjustment 32
Set the Governor 33
Pressure Testing 33
Ax Label 33
32
4. Cooking Tips 14
5. Cooking Table 15
6. Cleaning your cooker 16
Essential information 16
Hotplate burners 16
The Griddle 17
Glide-out Grill 17
Ovens 18
Cleaning table 19
10. Servicing 34
1 Panels 34
2 Hotplate 34
3 Controls 35
4 Grill 36
5 Ovens 36
6 Doors 38
11. Circuit Diagram 40
12. Technical Data 41
Classic 110 Dual Fuel
iii
iv
1. Before You Start...
Your cooker should give you many years of trouble-free
cooking if installed and operated correctly. It is important
that you read this section before you start.
Personal Safety
This appliance is for cooking purposes only. It must not be
used for other purposes, for example heating a room. Using
it for any other purpose could invalidate any warranty or
liability claim. Besides invalidating claims this wastes fuel and
may overheat the control knobs.
This cooker must be installed in accordance with the relevant
instructions in this booklet and with the national and local
regulations as well as the local gas and electricity supply
companies’ requirements.
• This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Children less than 8 years of age should be kept away
unless continuously supervised. Children shall not play
with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• DO NOT spray aerosols in the vicinity of the cooker
while it is on.
Electrical Connection Safety
All installations must be in accordance with the relevant
instructions in this booklet, with the relevant national
and local regulations and with the local electricity supply
companies’ requirements.
WARNING: THE APPLIANCE MUST BE EARTHED.
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double-pole
switch, having a contact separation of at least 3 mm in all
poles.
Read the instructions before installing or using this appliance
Gas Connection Safety
• This cooker is a Class 2 Subclass 1 appliance.
• This appliance can be converted for use on another gas.
• Before installation, make sure that the cooker is suitable
for your gas type and supply voltage. See the data
badge.
• The cooker should not be placed on a base.
• This appliance is designed for domestic cooking only.
Use for any other purpose could invalidate any warranty
or liability claim.
• Before operating the oven(s) please refer to the oven
shelf installation, in the Accessories section.
• The appliance and its accessible parts become hot
during use and will retain heat even after you have
stopped cooking. Care should be taken to avoid
touching heating elements.
• A long term cooking process has to be supervised from
time to time. A short term cooking process has to be
supervised continuously.
• At the risk of fire DO NOT store items on the cooking
surfaces.
• To avoid overheating, DO NOT install the cooker behind
a decorative door.
• Accessible parts will become hot during use and will
retain heat even after you have stopped cooking. Keep
babies and children away from the cooker and never
wear loose-fitting or hanging clothes when using the
appliance.
• DO NOT use reconditioned or unauthorised gas
controls.
• Disconnect from the electricity and gas supply before
servicing.
• When servicing or replacing gas-carrying components
disconnect from the gas supply before starting
operation. Check the appliance is gas sound after
completion.
• Make sure that the gas supply is turned on and that the
cooker is wired in and switched on.
• In your own interest and that of safety, it is law that all
gas appliances be installed by a qualified person(s).
• An appliance for use on LPG must not be installed in
a room or internal space below ground level, e.g. in a
basement.
• DO NOT use a steam cleaner on your cooker.
• Always keep combustible materials, e.g. curtains, and
flammable liquids a safe distance away from the cooker.
1
If You Smell Gas
Maintenance
• DO NOT turn electric switches on or off
• DO NOT smoke
• DO NOT use naked flames
• Turn off the gas at the meter or cylinder
• Open doors and windows to get rid of the gas
• Keep people away from the area affected
• Call your gas supplier
Peculiar Smells
When you rst use your cooker it may give o an odour. This
should stop after use.
Before using for the rst time, make sure that all packing
materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200 °C and run for at
least an hour.
Before using the grill for the rst time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back and the grill door open.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
• Only a qualified service engineer should service the
appliance and only approved spare parts should be
used. It is recommended that this appliance is serviced
annually.
• Before removing the existing bulb, turn o the power
supply and make sure that the oven and bulb have
cooled.
• DO NOT use cooking vessels on the hotplate that overlap
the edges.
• Unless specified otherwise in this guide, always allow
the appliance to cool and then switch it off at the mains
before cleaning or carrying out any maintenance work.
• DO NOT use the control knobs to manoeuvre the cooker.
• NEVER operate the cooker with wet hands.
• DO NOT use a towel or other bulky cloth in place of a
glove – it might catch fire if brought into contact with a
hot surface.
• DO NOT use hotplate protectors, foil or hotplate covers
of any description. These may affect the safe use of your
hotplate burners and are potentially hazardous to health.
• NEVER heat unopened food containers. Pressure build
up may make the containers burst and cause injury.
Ventilation
The use of a cooking appliance results in the production
of heat and moisture in the room in which it is installed.
Therefore, make sure that the kitchen is well ventilated:
keep natural ventilation holes open or install a powered
cookerhood that vents outside. If you have several hotplates/
burners on, or use the cooker for a long time, open a window
or turn on an extractor fan
• DO NOT use unstable saucepans. Always make sure
that you position the handles away from the edge of the
hotplate.
• NEVER leave the hotplate unattended at high heat
settings. Pans boiling over can cause smoking, and greasy
spills may catch on fire. Use a deep fat thermometer
whenever possible to prevent fat overheating beyond
the smoking point.
• Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
• NEVER leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should be
only one third full of fat.
• NEVER try to move a pan of hot fat, especially a deep fat
fryer. Wait until the fat is cool. Filling the pan too full of
fat can cause spill over when food is added. If you use a
combination of oils or fats in frying, stir them together
before heating, or as the fats melt.
• Foods for frying should be as dry as possible. Frost on
frozen foods or moisture on fresh foods can cause hot
fat to bubble up and over the sides of the pan. Carefully
watch for spills or overheating of foods when frying at
high or medium high temperatures.
• DO NOT use the top of the flue (the slot along the back of
the cooker) for warming plates, dishes, drying tea towels
or softening butter.
2
• DO NOT use water on grease fires and never pick up
a flaming pan. Turn the controls off and then smother
a flaming pan on a surface unit by covering the pan
completely with a well fitting lid or baking tray. If
available, use a multi-purpose dry chemical or foamtype fire extinguisher.
Fig. 1.1
• DO NOT modify this appliance. This appliance is not
intended to be operated by means of external timer or
separated remote-control system.
• If flammable materials are stored in the drawer, oven(s)
or grill(s) it may explode and result in fire or property
damage.
Oven Care
• When the oven is not in use and before attempting
to clean the cooker always be certain that the control
knobs are in the OFF position.
• Use oven gloves to protect your hand from potential
burns.
• Cooking high moisture content foods can create a
‘steam burst’ when the oven door is opened (Fig. 1.1).
When opening the oven, stand well back and allow any
steam to disperse.
• The inside door face is constructed with toughened
safety glass. Take care NOT to scratch the surface when
cleaning the glass panel.
ArtNo.324-0001 Steam burst
• Accidental damage may cause the door glass panel to
fracture.
• Keep oven vent ducts unobstructed.
• DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
• Make sure the shelves are pushed firmly to the back
of the oven. DO NOT close the door against the oven
shelves.
• DO NOT use aluminium foil to cover shelves, linings or
the oven roof.
• When the oven is on, DO NOT leave the oven door open
for longer than necessary, otherwise the control knobs
may become very hot.
• DO NOT use the timed oven if the adjoining oven is
already warm.
• DO NOT place warm food in the oven to be timed.
• DO NOT use a timed oven that is already warm.
• Use dry oven gloves when applicable – using damp
gloves might result in steam burns when you touch a
hot surface.
3
Grill/Glide-out Grill™ Care
Cleaning
• When using the grill, make sure that the grill pan is
in position and pushed fully in, otherwise the control
knobs may become very hot.
• DO NOT leave the grill on for more than a few moments
without the grill pan underneath it, otherwise the knobs
may become hot.
• NEVER close the grill door when the grill is on.
• Accessible parts may be hot when the grill is in use.
Young children should be kept away.
Cooling Fan
This appliance may have a cooling fan. When the grill or
ovens are in operation the fan will run to cool the fascia and
control knobs.
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours.
• Isolate the electricity supply before carrying out any
thorough cleaning. Allow the cooker to cool.
• In the interests of hygiene and safety, the cooker should
be kept clean at all times as a build up in fats and other
food stuff could result in a fire.
• Clean only the parts listed in this guide.
• Clean with caution. If a wet sponge or cloth is used to
wipe spills on a hot surface, be careful to avoid steam
burns. Some cleaners can produce noxious fumes if
applied to a hot surface.
• NEVER use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.
• DO NOT mix different cleaning products – they may
react together with hazardous results.
• All parts of the cooker can be cleaned with hot soapy
water.
• Take care that no water seeps into the appliance.
• Before you remove any of the grill parts for cleaning,
make sure that they are cool or use oven gloves.
• DO NOT use any abrasive substances on the grill and
grill parts.
• DO NOT put the side runners in a dishwasher.
• DO NOT put the burner heads in a dishwasher.
• NEVER use caustic or abrasive cleaners as these will
damage the surface.
• DO NOT use steel wool, oven cleaning pads or any other
materials that will scratch the surface.
• NEVER store flammable materials in the drawer.
This includes paper, plastic and cloth items, such
as cookbooks, plastic ware and towels, as well as
flammable liquids.
• DO NOT store explosives, such as aerosol cans, on or
near the appliance.
• DO NOT attempt to disassemble or clean around any
burner while another burner is on, otherwise an electric
shock could result.
4
2. Cooker Overview
A
DocNo.020-0013 - Overview - 110DF - Classic, RM & Toledo lidded
Fig. 2.1
0
B
99
SS
88
77
66
11
55
44
22
33
M
H G
0
99
SS
88
77
66
11
55
44
22
33
C
M
E
D
F
The 110 dual fuel cooker (Fig. 2.1) has the following features:
A. 6 hotplate burners including a wok burner
B. A control panel
C. A glide-out grill
D. A (programmable) fan oven
E. A Fan oven
F. Storage drawer
Hotplate Burners
The drawing by each of the central knobs indicates which
burner that knob controls.
Each burner has a Flame Supervision Device (FSD) that
prevents the ow of gas if the ame goes out.
When the igniter button is pressed in, sparks will be
made at every burner – this is normal. Do not attempt to
disassemble or clean around any burner while another
burner is on, otherwise an electric shock could result.
To light a burner, press the igniter button, and push in and
turn the associated control knob to the high position as
indicated by the large ame symbol (
), (Fig. 2.2).
Fig. 2.2
5
ArtNo.311-0001 Right pans gas
Fig. 2.3
Fig. 2.4 Fig. 2.5
ArtNo.311-0002 Pan with rim
Fig. 2.6 Fig. 2.7
The igniter should spark and light the gas. Keep holding the
knob pressed in to let the gas through to the burner for about
ten seconds.
If, when you let go of the control knob, the burner goes out,
then the FSD has not been bypassed. Turn the control knob
to the OFF position and wait for one minute before you try
again, this time making sure to hold in the control knob for
slightly longer.
Adjust the ame height to suit by turning the knob clockwise
(Fig. 2.3).
If a burner ame goes out, turn o the control knob and
leave it for one minute before relighting it.
Make sure that the ames are under the pans. Using a lid will
help the contents boil more quickly (Fig. 2.4).
Large pans should be spaced well apart.
Pans and kettles with concave bases or down-turned base
rims should not be used (Fig. 2.5).
Simmering aids, such as asbestos or mesh mats, are
NOT recommended (Fig. 2.6). They will reduce burner
performance and could damage the pan supports.
You should also avoid using unstable and misshapen pans
that may tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers (Fig. 2.7).
Art No. 311-0003 Simmer aids
Fig. 2.8
ArtNo.311-0005 Wok burner & pan support
ArtNo.311-0004 Tipping wok
The minimum recommended pan diameter is 120 mm. The
maximum allowable pan base diameter is 260 mm.
DO NOT use cooking vessels on the hotplate that overlap the
edges.
Wok Burner
The wok burner is designed to provide even heat over a large
area. They are ideal for large pans and stir-frying (Fig. 2.8).
For heating smaller pans, the aforementioned hotplate
burners may be more ecient.
You should wipe the enamel top surface of the cooker around
the hotplate burners as soon as possible after spills occur. Try
to wipe them o while the enamel is still warm.
NOTE:
The use of aluminium pans may cause metallic
marking of the pan supports. This does not aect the
durability of the enamel and may be cleaned o with an
appropriate metal cleaner.
6
The Wok Cradle (optional extra)
The wok cradle is designed to t a 35 cm wok. If you use a
dierent wok, make sure that it ts the cradle. Woks vary very
widely in size and shape. It is important that the wok sits
down on the pan support – however, if the wok is too small,
the cradle will not support it properly (Fig. 2.9).
The cradle should be used on the wok burner only. When you
t the cradle, make sure that it is supported properly on a pan
support and the wok is sitting level in the cradle (Fig. 2.10).
Fig. 2.9
ArtNo.311-0006 Correct wok sizes
The cradle will get very hot in use – allow plenty of time for it
to cool before you pick it up.
The Griddle
The griddle ts the left-hand pan support, front to back (Fig.
2.11). It is designed for cooking food on directly. DO NOT use
pans of any kind on it. The griddle surface is non-stick and
metal cooking utensils (e.g. spatulas) will damage the surface.
Use heat resistant plastic or wooden utensils.
DO NOT put it crossways – it will not t properly and
will be unstable (Fig. 2.12).
DO NOT put it on any other burner – it is not
designed to t in any of the other pan supports.
Position the griddle over the hotplate burners resting on the
pan support. Check that it is securely located.
The griddle can be lightly brushed with cooking oil before
use (Fig. 2.13). Light the hotplate burners. Adjust the ame
heights to suit.
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. Turn the
control knobs towards the low position, marked with the
small ame symbol, to reduce the burner ames.
ArtNo.311-0007 Wok stand close-up
ArtNo.110-0013 Positioning the griddle on hotplate (right)
ArtNo.110-0014 Positioning the griddle on hotplate (wrong)
Fig. 2.10
Fig. 2.11
Fig. 2.12
Always leave space around the griddle for the gases
to escape.
NEVER t two griddles side by side (Fig. 2.14).
After cooking, allow the griddle to cool before cleaning.
ArtNo.311-0009 Oil on griddle
Fig. 2.13
Fig. 2.14
ArtNo.311-0008 Griddle positioning
7
ArtNo.331-0001Grill pan pulled forwards
Fig. 2.15
Fig. 2.16
The Grill
CAUTION: This appliance is for cooking purposes
only. It must not be used for other purposes, for
example room heating.
CAUTION: Accessible parts may be hot when the grill
is in use. Young children should be kept away.
Open the door and pull the grill pan forward using the handle
(Fig. 2.15).
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
Adjust the heat to suit by turning the control knob. To heat
the whole grill, turn the control knob clockwise (Fig. 2.16).
To heat the right-hand half, turn the control knob counterclockwise.
Fig. 2.17
ArtNo.235-0007 - Classic
DL grill control
ArtNo.331-0002 Grill pan high/low position
The neon indicator light by the grill control will come on.
For best results, slide the grill pan back into the grill chamber
and preheat the appropriate part(s) of the grill for two
minutes. The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
Once the grill has preheated, slide the grill pan out again.
With the trivet back in place with the food on it, slide the grill
pan back into the grill chamber. Make sure that it is pushed
right in.
The grill trivet can be turned over to give two grilling
positions (Fig. 2.17).
DO NOT leave the grill on for more than a few moments,
without the grill pan underneath it.
Never close the grill door when the grill is on.
8
The Ovens
ArtNo.321-0002 Fan assisted oven
The clock must be set to the time of day before the ovens will
work. See the following section on ‘The Clock’ for instructions
on setting the time of day.
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
The left-hand oven is a programmable fan oven (Fig. 2.18),
while the right-hand oven is a fan oven (Fig. 2.19).
The Fan Oven
The right-hand oven is a fan oven that circulates hot air
continuously, which means faster, more even cooking.
The recommended cooking temperatures for a fan oven are
generally lower than a conventional oven.
NOTE: Please remember that all cookers vary so
temperatures in your new ovens may dier to those in your
previous cooker.
Operating the Ovens
Fig. 2.18
Fan oven
Fig. 2.19
Fan oven
Fan Ovens
Turn the oven knob to the desired temperature (Fig. 2.20).
The oven indicator light will glow until the oven has reached
the temperature selected. It will then cycle on and o during
cooking (Fig. 2.21).
Main Oven Lights
Press the button to turn the lights on (Fig. 2.22).
If an oven light fails, turn o the power supply before
changing the bulb. See the ‘Troubleshooting’ section for
details on how to change the bulb.
ArtNo.321-0002 Fan assisted oven
Fig. 2.20
ArtNo.235-0004 -
Classic DL oven 1
Fig. 2.21
ArtNo.235-0005 - Classic
DL oven control 2
Fig. 2.22
ArtNo.320-0026
- Oven light
9
ArtNo.320-0013 Removing the shelf 3
ArtNo.320-0011 Removing the shelf 1
ArtNo.320-0012 Removing the shelf 2
Fig. 2.23
Fig. 2.24
Fig. 2.26
Front
Shelf guard
Fig. 2.25
Accessories
Oven Shelves
The oven shelves (Fig. 2.23) can be easily removed and
retted.
Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig. 2.24).
Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward
(Fig. 2.25).
To ret the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig. 2.26).
The Handyrack (Main Oven)
The Handyrack (Fig. 2.27) ts to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.
The maximum weight that can be held by the Handyrack
is 5.5 kg (12 lb). It should only be used with the supplied
roasting tin, which is designed to t the Handyrack. Any other
vessel could be unstable.
Fig. 2.27
ArtNo.320-0014 Handyrack on LH door
Fig. 2.28 Fig. 2.29
ArtNo.320-0015
Fitting the Handyack 1
ArtNo.320-0016
Fitting the handyrack 2
It can be tted at two dierent heights. One of the oven
shelves must be removed and the other positioned to suit.
When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.
To t the Handyrack, locate one side of it on the door bracket
(Fig. 2.28).
Then spring the other side out to clip it onto the other
bracket (Fig. 2.29).
Storage
The bottom drawer is for storing oven trays and other
cooking utensils. It can get very warm, so do not store
anything in it that may melt or catch re.
The drawer can be removed completely by pulling it right out
and up.
10
1
2
FRONT
FRONT
Rear stop
Front
bracket
Glide-out Oven Shelf (optional)
A glide-out oven shelf is available for either oven (Fig. 2.30).
Note: The Handyrack must be removed before tting the
glide-out shelf.
The rungs on the shelf supports are in pairs. The glide-out
shelf runners can be tted to any pair except the top.
To t the glide-out shelf runners
Hook the rear of the runner over the top rung of a pair of shelf
supports. Then hook the front of the runner onto the same
rung. Push to clip under the bottom rung (Fig. 2.31).
The front of the shelf runners can be identied by the bracket
(Fig. 2.33).
Ensure that the shelf runners are tted in the same position
on each side (Fig. 2.32).
To t the glide-out shelf
Check the shelf runners are secure before tting the glide-out
shelf.
Hook the front of the glide-out oven shelf onto the runners
as shown (Fig. 2.33). The rear of the shelf should rest on the
runners, in front of the rear stop (Fig. 2.33).
Fig. 2.30
Fig. 2.31
Fig. 2.32
Ensure that the shelf sits at once in position.
DO NOT put the glide-out shelf runners in a
dishwasher
Fig. 2.33
11
Loading...