Falcon CDL110DFCR-BR, CDL90DFBL-BR, CDL90DFBL-CH, CDL90DFCR-BR, CDL90DFBL-CHLPG User Manual

USER GUIDE &

INSTALLATION INSTRUCTIONS

Classic Deluxe 90cm Dual Fuel

Australia

U110288-01A

Contents

1. Before You Start... 1

Installation and Maintenance 1
Peculiar Smells 1
If You Smell Gas 1
Ventilation 1
Personal Safety 1
Cooker Care 2
Cleaning 2

2. Cooker Overview 3

Hotplate Burners 3
Wok Burner 4
The Wok Cradle 5
The Griddle 5
The Glide-out Grill 6
The Ovens 7
The Clock 9
Accessories 11
Main Oven Light 11

3. Cooking Tips 12

Tips on Cooking with the Timer 12
General Oven Tips 12

4. Cooking Table 13

5. Cleaning Your Cooker 14

Essential Information 14
Hotplate Burners 14
The Griddle 15
Glide-out Grill 15
Control Panel and Doors 15
Ovens 16
Ret in the reverse order. 16
The Tall Oven 16
Cleaning Table 17

6. Troubleshooting 18

7. Installation 20

Service and Spares 20
Dear Installer 21
Provision of Ventilation 21
Location of Cooker 21
Conversion 21
Positioning the Cooker 23
Moving the Cooker 23
Completing the Move 24
Fitting the Stability Bracket and Chain 24
Repositioning the Cooker Following

Connection
Levelling 25
Gas Connection 26
Pressure Testing 26
Electrical Connection 27
Final Checks 28
Final Fitting 28
Customer Care 28

25

8. Conversion to LP Gas 29

Injectors 29
Tap Adjustment 29
Set the Governor 30
Pressure Testing 30
Ax Label 30

9. Servicing 31

10. Circuit Diagram 38

11. Technical Data 39

Classic Deluxe 90 DF (Australia) U110288-01A

i

1. Before You Start...

Thank you for buying a Falcon cooker. It should give you
many years of trouble-free cooking if installed and operated
correctly. It is important that you read this section before
you start, particularly if you have not used a dual fuel cooker
before.

This appliance is designed for domestic cooking



only. Using it for any other purpose could invalidate
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen –
besides invalidating claims this wastes fuel and may
overheat the control knobs.

Certain types of vinyl or laminate kitchen furniture



are particularly prone to heat damage and
discolouration. We cannot accept responsibility
for damage caused by normal use of the cooker
to any material that de-laminates or discolours
at temperatures less than 70 °C above room
temperature (as measured by EN30 / EN60335).

Installation and Maintenance

The installation must be in accordance with the relevant
instructions in this booklet, with the relevant national and
local regulations, and with the local gas and electricity supply
companies’ requirements.

Make sure that the gas supply is turned on and that the
cooker is wired in and switched on (the cooker needs
electricity).

Set the clock to make sure that the oven is functional – see
the relevant section in this manual.

The cooker should be serviced only by a qualied service
engineer, and only approved spare parts should be used.

Always allow the cooker to cool and then switch it o at the
mains before cleaning or carrying out any maintenance work,
unless specied otherwise in this guide.

Peculiar Smells

When you rst use your cooker it may give o an odour. This
should stop after use.

Before using for the rst time, make sure that all packing
materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200 °C and run for at
least an hour.

Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.

If You Smell Gas

• DO NOT turn electric switches on or off

• DO NOT smoke

• DO NOT use naked flames

• DO turn off the gas at the meter or cylinder

• DO open doors and windows to get rid of the gas

• DO keep people away from the area affected

• Call your gas supplier

Ventilation

The use of a gas cooking appliance results in the production
of heat and moisture in the room in which it is installed.
Therefore, make sure that the kitchen is well ventilated: keep
natural ventilation holes open or install a powered cooker
hood that vents outside. If you have several burners on, or
use the cooker for a long time, open a window or turn on an
extractor fan.

Personal Safety

DO NOT modify this appliance.



This appliance can be used by children aged from 8



years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in
a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.

WARNING: The appliance and its accessible parts



become hot during use and will retain heat even
after you have stopped cooking. Care should be
taken to avoid touching heating elements. Children
less than 8 years of age shall be kept away unless
continuously supervised.

DO NOT use a steam cleaner on your cooker.



CAUTION: A long term cooking process has to be



supervised from time to time. A short term cooking
process has to be supervised continuously.

Danger of re: DO NOT store items on the cooking



surfaces.

To avoid overheating, DO NOT install the cooker



behind a decorative door.

Accessible parts will become hot during use and will



retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and
never wear loose-tting or hanging clothes when
using the appliance.

Always be certain that the controls are in the OFF



position when the oven is not in use, and before
attempting to clean the cooker.

1

When the oven is on, DO NOT leave the oven door



open for longer than necessary – otherwise, the
control knobs may become very hot.

Cooking high moisture content
foods can create a ‘steam burst’
when the oven door is opened.
When opening the oven stand
well back and allow any steam to
disperse.

DO NOT drop or rest objects on the door glass.



Although the glass is very strong, a sharp blow or a
falling object might cause the glass surface to crack
or break.

DO NOT use harsh abrasive cleaners or sharp metal



scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.

Always keep combustible materials, e.g. curtains,



and ammable liquids a safe distance away from
your cooker.

DO NOT store ammable materials in the vicinity of



this unit

DO NOT spray aerosols in the vicinity of the cooker



while it is on.

Use dry oven gloves when applicable – using damp gloves
might result in steam burns when you touch a hot surface.
Do not use a towel or other bulky cloth in place of a glove – it
might catch re if brought into contact with a hot surface.

NEVER operate the cooker with wet hands.



DO NOT use aluminium foil to cover shelves, linings



or the oven roof.

DO NOT use hotplate protectors, foil or hotplate



covers of any description. These may aect the safe
use of your hotplate burners and are potentially
hazardous to health.

NEVER heat unopened food containers. Pressure



build up may make the containers burst and cause
injury.

DO NOT use unstable saucepans. Always make sure



that you position the handles away from the edge of
the hotplate.

DO NOT use cooking vessels on the hotplate that



overlap the edges.

ArtNo.324-0001 Steam burst

NEVER leave a chip pan unattended. Always heat fat



slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.

Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan.

Carefully watch for spills or overheating of foods when frying
at high or medium high temperatures. Never try to move a
pan of hot fat, especially a deep fat fryer. Wait until the fat is
cool.

Do not use the top of the ue (the slot along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.

DO NOT use water on grease res and never pick up a
aming pan. Turn the controls o and then smother
a aming pan on a surface unit by covering the pan
completely with a well tting lid or baking tray. If
available, use a multi-purpose dry chemical or foam-type
re extinguisher.

Take care that no water seeps into the appliance.



In normal use, the cooling fan will operate when the



oven or grill are in use. Should a fault occur with the
fan switch o the cooker immediately and contact
your installer or service.

Only certain types of glass, glass-ceramic, earthenware or
other glazed containers are suitable for hotplate cooking;
others may break because of the sudden change in
temperature.

This appliance is heavy so take care when moving it.



The appliance is not intended to be operated by



means of external timer or separated remote-control
system.

Cooker Care

As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours.

Cleaning

In the interests of hygiene and safety, the cooker should be
kept clean at all times as a build up in fats and other food
stu could result in a re.

Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on re. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.

WARNING! Unattended cooking on a hob with fat or



oil can be dangerous and may result in re.

Clean only the parts listed in this guide.

Clean with caution. If a wet sponge or cloth is used to wipe
spills on a hot surface, be careful to avoid steam burns. Some
cleaners can produce noxious fumes if applied to a hot
surface.

2

2. Cooker Overview

A

B

C

D

DocNo.020-0002 - Overview - 90 Ceramic - Generic

Fig.2-1

C

LASSI

C

DELUXE

90

E

The 90 dual fuel cooker (Fig.2-1) has the following features:

A. 5 hotplate burners including a wok burner
B. A control panel
C. A glide-out grill
D. A main programmable multi-function oven.
E. Tall fan oven

Hotplate Burners

The drawing by each of the central knobs indicates which
burner that knob controls.

Each burner has a Flame Supervision Device (FSD) that
prevents the ow of gas if the ame goes out.

When the control knob is pressed in, sparks will be
made at every burner – this is normal. Do not attempt to
disassemble or clean around any burner while another
burner is on, otherwise an electric shock could result.

To light a burner, push in and turn the associated control
knob to the high position as indicated by the large ame
symbol (

), (Fig.2-2).



Fig.2-2

3

Fig.2-3

Fig.2-4

The igniter should spark and light the gas. Keep holding the
knob pressed in to let the gas through to the burner for about
ten seconds.

If, when you let go of the control knob, the burner goes out,
then the FSD has not been bypassed. Turn the control knob
to the OFF position and wait for one minute before you try
again, this time making sure to hold in the control knob for
slightly longer.

Adjust the ame height to suit by turning the knob counter­clockwise (Fig.2-3).

If a burner ame goes out, turn o the control knob and
leave it for one minute before relighting it.

Make sure that the ames are under the pans. Using a lid will
help the contents boil more quickly (Fig.2-4).

Large pans should be spaced well apart.

Pans and kettles with concave bases or down-turned base
rims should not be used (Fig.2-5).

Fig.2-5

Fig.2-6

Fig.2-7

ArtNo.311-0001 Right pans gas

ArtNo.311-0002 Pan with rim

Art No. 311-0003 Simmer aids

ArtNo.311-0004 T ipping wok

Simmering aids, such as asbestos or mesh mats, are
NOT recommended (Fig.2-6). They will reduce burner
performance and could damage the pan supports.

You should also avoid using unstable and misshapen pans
that may tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers (Fig.2-7).

The minimum recommended pan diameter is 120 mm. The
maximum allowable pan base diameter is 260 mm.

DO NOT use cooking vessels on the hotplate that overlap the
edges.

Wok Burner

The wok burner is designed to provide even heat over a large
area. It is ideal for large pans and stir-frying (Fig.2-8).

For heating smaller pans, the aforementioned hotplate
burners may be more ecient.

You should wipe the enamel top surface of the cooker around
the hotplate burners as soon as possible after spills occur. Try
to wipe them o while the enamel is still warm.

Note:

The use of aluminium pans may cause metallic marking
of the pan supports. This does not aect the durability of the
enamel and may be cleaned o with an appropriate metal
cleaner.

Fig.2-8

ArtNo.311-0005 Wok burner & pan support

4

The Wok Cradle

The wok cradle is designed to t a Professional 35 cm wok. If
you use a dierent wok, make sure that it ts the cradle. Woks
vary very widely in size and shape. It is important that the
wok sits down on the pan support – however, if the wok is too
small, the cradle will not support it properly (Fig.2-9).

The cradle should be used on the triple ring wok burner only.
When you t the cradle (Fig.2-10), check that it is properly
located on the pan supports and that the wok it is sitting level
in the cradle.

The cradle will get very hot in use – allow plenty of time for it
to cool before you pick it up.

The Griddle

The griddle ts the left-hand pan support, front to back
(Fig.2-11). It is designed for cooking food on directly. DO NOT
use pans of any kind on it. The griddle surface is non-stick and
metal cooking utensils (e.g. spatulas) will damage the surface.
Use heat resistant plastic or wooden utensils.

DO NOT put it crossways – it will not t properly and



will be unstable (Fig.2-12).

DO NOT put it on any other burner – it is not



designed to t in any of the other pan supports.

Fig.2-9

ArtNo.311-0006 Correct wok sizes

Fig.2-10

ArtNo.311-0007 Wok stand close-up

Fig.2-11

Position the griddle over the hotplate burners resting on the
pan support. Check that it is securely located.

The griddle can be lightly brushed with cooking oil before
use (Fig.2-13). Light the hotplate burners. Adjust the ame
heights to suit.

Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. Turn the
control knobs towards the low position, marked with the
small ame symbol, to reduce the burner ames.

Always leave space around the griddle for the gases



to escape.

NEVER t two griddles side by side (Fig.2-14).



After cooking, allow the griddle to cool before cleaning.

ArtNo.311-0009 Oil on griddle

Fig.2-12

Fig.2-13

Fig.2-14

ArtNo.311-0008 Griddle positioning

5

Fig.2-15

The Glide-out Grill

Open the door and pull the grill pan carriage forward using
the handle (Fig.2-15).

The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.

Adjust the heat to suit by turning the knob. To heat the whole
grill, turn the knob clockwise (Fig.2-16).

Fig.2-16

Fig.2-17

ArtNo.331-0001Grill pan pulled forwards

ArtNo.235-0007 - Classic

DL grill control

ArtNo.331-0002 Grill pan high/low position

To heat the right-hand half, turn the knob counter-clockwise.
The neon indicator light by the grill control will come on.

For best results, leave the grill pan in the grill chamber and
preheat the appropriate part(s) of the grill for two minutes.
The grill trivet can be removed and the food placed on it
while you are waiting for the grill to preheat.

DO NOT leave the grill on for more than a few



moments, without the grill pan underneath it,
otherwise the knobs may become hot.

Once the grill has preheated, take the grill pan out again and
put the trivet back in place with the food on it. Slide the grill
pan or carriage back into the grill chamber. Make sure that it
is pushed right in.

Accessible parts may be hot when the grill is in use.



Young children should be kept away.

The grill pan trivet can be turned over to give two grilling
positions (Fig.2-17).

Never close the grill door when the grill is on.



6

The Ovens

The clock must be set to the time of day before the left­hand oven will work. See the following section on ‘The
Clock’ for instructions on setting the time of day.

References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.

The left-hand oven is a multi-function oven.

The right-hand tall oven is a fan oven.

Fan ovens circulate hot air continuously, which means
faster, more even cooking. The recommended cooking
temperatures for a fan oven are generally lower than those
for a non-fan oven.

Multi-function ovens have an oven fan and oven fan element,
as well as two extra heating elements. One element is in
the top of the oven and the second is under the oven base.
Take care to avoid touching the top element and element
deector when placing or removing items from the oven.

The multi-function oven has 3 main cooking functions: fan,
fan assisted and conventional cooking. These functions
should be used to complete most of your cooking.

The browning element and base heat can be used in the
latter part of the cooking process to ne tune the results to
your particular requirements.

Function Use

Rapid response To quickly heat up the oven

Defrost

Fan oven

Fanned grilling

Fan assisted

Conventional oven

Browning element

Base heat

To thaw small items in the oven without
heat

A full cooking function, even heat
throughout, great for baking

Grilling meat and fish with the door
closed

A full cooking function good for roasting
and baking

A full cooking function for roasting and
baking in the lower half of the oven

To brown and crisp cheese topped
dishes

To crisp up the bases of quiche, pizza or
pastry

Table 2-1

Use fanned grilling for all your grilling needs and defrost to
safely thaw small items of frozen food.

Table 2-1 gives a summary of the multi-function modes.

The multi-function oven has many varied uses. We suggest
you keep a careful eye on your cooking until you are familiar
with each function. Remember, not all functions will be
suitable for all food types.

7

Multi-function Oven Functions

Rapid Response

The Rapid Response setting enables you to preheat
the oven faster than normal. It uses the fan oven

element with additional heat from one of the
elements in the top of the oven. Fan ovens heat up quickly;
but the Rapid Response feature speeds this process up
enabling you to start cooking sooner.

To use the Rapid Response feature, turn the function control
knob to R and set the temperature required. The light on the
control panel next to the function control will come on.

When the required temperature is reached the top element
will switch o and the light will go out.

The oven temperature is then maintained by the fan oven
element and fan. Should you choose to place food into the
cold oven prior to cooking while using the Rapid Response
function, make sure that cakes, etc. are not positioned too
near the top of the oven.

Fan Oven

This function operates the fan and the heating

element around it. An even heat is produced

throughout the oven, allowing you to cook large
amounts quickly.

Fan oven cooking is particularly suitable for baking on several
shelves at one time and is a good ‘all-round’ function. It may
be necessary to reduce the temperature by approximately
10 °C for recipes previously cooked in a conventional oven.

If you wish to preheat the oven, wait until the indicator light
has gone out before inserting the food.

Fanned Grilling

This function operates the fan whilst the top element

is on. It produces a more even, less erce heat than a

conventional grill. For best results, place the food to
be grilled, on a trivet over a roasting tin, which should be
smaller than a conventional grill pan. This allows greater air
circulation. Thick pieces of meat or sh are ideal for grilling in
this way, as the circulated air reduces the erceness of the
heat from the grill.

The oven door should be kept closed while grilling is in
progress, so saving energy.

You will also nd that the food needs to be watched and
turned less than for normal grilling. Preheat this function
before cooking.

For best results we recommend that the grill pan is not
located on the uppermost shelf.

Fan Assisted Oven

This function operates the fan, circulating air heated

by the elements at the top and the base of the oven.

The combination of fan and conventional cooking
(top and base heat) makes this function ideal for cooking
large items that need thorough cooking, such as a large meat
roast.

It is also possible to bake on two shelves at one time,
although they will need to be swapped over during the
cooking time, as the heat at the top of the oven is greater
than at the base, when using this function.

This is a fast intensive form of cooking; keep an eye on the
food cooking until you have become accustomed to this
function.

Conventional Oven (Top and Base Heat)

This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits.

Food cooked on the top shelf will brown and crisp faster than
on the lower shelf, because the heat is greater at the top of
the oven than at the base, as in ‘Fan assisted oven’ function.
Similar items being cooked will need to be swapped around
for even cooking. This means that foods requiring dierent
temperatures can be cooked together, using the cooler zone
in the lower half of the oven and hotter area to the top.

The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.

Browning Element

This function uses the element in the top of the oven
only. It is a useful function for the browning or

nishing of pasta dishes, vegetables in sauce,
shepherds pie and lasagne, the item to be browned being
already hot before switching to the top element.

Base Heat

This function uses the base element only. It will crisp

up your pizza or quiche base or nish o cooking the

base of a pastry case on a lower shelf. It is also a
gentle heat, good for slow cooking of casseroles in the
middle of the oven or for plate warming.

The Browning and Base Heat functions are useful additions
to your oven, giving you exibility to nish o items to
perfection.

Defrost

This function operates the fan to circulate cold air

only. Make sure the temperature control is at 0°C and

that no heat is applied. This enables small items such
as desserts, cream cakes and pieces of meat, sh and poultry
to be defrosted.

Defrosting in this way speeds up the process and protects
the food from ies. Pieces of meat, sh and poultry should
be placed on a shelf, over a tray to catch any drips. Be sure to
wash the shelf and tray after defrosting.

Defrost with the oven door closed.

Large items, such as whole chickens and joints should not be
defrosted in this way. We recommend this be carried out in a
refrigerator. Defrosting should not be carried out in a warm
oven or when an adjoining oven is in use or still warm.

8

Make sure that dairy foods, meat and poultry are completely

ArtNo.302-0004 -

Minute minder setting 2

defrosted before cooking.

Operating the Ovens

Fan Oven

Turn the oven knob to the desired temperature (Fig.2-18).

The oven indicator light will glow until the oven has reached
the temperature selected. It will then cycle on and o during
cooking.

Multi-function Oven

The multi-function oven has two controls: a function selector
and a temperature setting knob (Fig.2-19).

ArtNo.235-0004 -
Classic DL oven 1

Fig.2-18

Fig.2-19

Turn the function selector control to a cooking function. Turn
the oven temperature knob to the temperature required
(Fig.2-18).

The oven heating light will glow until the oven has reached
the temperature you selected. It will then cycle on and o
during cooking.

The Clock

You can use the clock to turn the left-hand oven on and o.

The clock must be set to the time of day before the oven
will work.

Note: When using the timer functions, rst set the clock as

required before setting the oven temperature and selecting
the oven function (multi-function ovens only).

Setting the Time of Day

The 6-button LCD clock is shown in Fig.2-20. When the
clock is rst connected the display ashes ( 0.00 ) and (G)
alternately.

Press and hold both the [C] and [D] buttons down
(Fig.2-21). Now press the [+] button (or the [–] button) until
the correct time shows.

Do not forget that it is a 24-hour clock.

ArtNo.235-0003 - Classic DL MF knobs

Temperature

ArtNo.302-0002 - 6BC annotated

Function

ABCDEF

A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time,

D – Manual, E & F – Time setting buttons

Fig.2-20

If you need to reset the cooker, turn o the power supply and
wait for a couple of minutes and start again.

Setting the Minute Minder

Press and hold the [C] button (Fig.2-22), and then press the
[+] button until the length of time you want to cook for is
shown (Fig.2-23).

You can check the time remaining by pressing [C]. When the
beeper sounds cancel it by pressing [C].

• The ‘cook period’, which is the length of time you
want the oven to cook for.

• The ‘stop time’, which is the time of day you want the
oven to stop cooking.

To Stop the Oven Automatically

Press and hold the Stop Time [E] button (Fig.2-24) and then
press the [+] button (or [–] button) until the required ‘stop

time’ shows (Fig.2-25). AUTO will show in the display.

Fig.2-21

ArtNo.302-0001 - 6-button clock

Fig.2-22 Fig.2-23

ArtNo.302-0003 - 6BC
minute minder setting 1

9

Fig.2-24

ArtNo.302-0005a -

6BC Stopping the oven 1a

ArtNo.302-0006 - 6BC
setting the cook time

ArtNo.302-0006 - 6BC
setting the cook time

ArtNo.302-0005a -

6BC Stopping the oven 1a

Fig.2-25

Once the ‘stop time’ is reached, the beeper sounds. To stop the
beep turn the oven control knob to 0 rst and then press [B]
once; press [B] again to return to manual cooking.

ArtNo.302-0005 -

6BC Stopping the oven 1

Fig.2-26

Fig.2-28

ArtNo.302-0005 -

6BC Stopping the oven 1

Fig.2-27

Fig.2-29

Fig.2-30 Fig.2-31

ArtNo.302-0008 ­Activating the key lock 1

ArtNo.302-0009 - Activating
the key lock 2

To Start and Stop the Oven Automatically

Before you set the clock you must have two numbers clearly
in mind – the ‘cook period’ and the ‘stop time’.

Note: You cannot set a start time directly – this is set
automatically by setting the ‘cook period’ and the ‘stop time’.

Press and hold the [D] button (Fig.2-26) and then press the
[+] button (or [–] button) until the required ‘cook period’ shows
(Fig.2-27).

Now press and hold the [E] button (Fig.2-28) and then press
the [+] button (or [–] button) until the required ‘stop time’
shows (Fig.2-29). Release the buttons.

AUTO will now show in the display.

Set the oven to the required temperature. When cooking is
nished the beeper will sound. Turn the oven knob to the OFF
position rst, and then press the [B] button once to stop the
beep; press it again to return to manual cooking.

If you are out, do not worry about the beeper going o, it
stops after a while. When you return, turn the oven knob to 0
rst, and then press [B] twice to return to manual cooking.

AUTO is Showing, But You Want to Reset to Manual
Cooking

To return to manual cooking from any automatic setting,
the ‘cook period’ must be cancelled. Press and hold the [E]
button and then press the [–] button until the display reads
(0.00 ).

Press the [B] button to return to manual cooking.

Fig.2-32

Fig.2-33

Fig.2-34

ArtNo.302-0010 ­Activating the key lock 3

ArtNo.302-0011 - 6BC
Deactivating the key lock 1

ArtNo.302-0012 ­Deactivating the key lock 2

Key Lock

Activating the key lock will lock the left-hand oven and it will
not come on.

The right-hand oven can be operated as usual.

To Activate the Key Lock

Make sure that the clock is in manual mode and cancel
any active programs.

Hold the [C] and [D] buttons. When ‘On’ appears on the
display (Fig.2-30) press the [+] button once. The key symbol
[F] and ‘OF’ will now show on the display (Fig.2-31). Release
the buttons.

The left-hand oven is now locked, as conrmed by the display
showing the time of day alongside the key symbol [F]
(Fig.2-32).

To Turn O the Key Lock

Hold the [C] and [D] buttons. When ‘OF’ appears on the
display (Fig.2-33) press the [+] button once. The key symbol
[F] will go out and ‘On’ will show on the display (Fig.2-34).
Release the buttons.

After a few seconds the display will revert to show the time of
day. The oven can now be used normally.

10

Accessories

ArtNo.320-0014 Handyrack on LH door

ArtNo.320-0012 Removing the shelf 2

Oven Shelves – Left-hand (Main) Oven

In addition to the at shelf, the cooker is supplied with a drop
shelf (Fig.2-35). The drop shelf increases the possibilities for
oven shelf spacing.

The oven shelves can be easily removed and retted.

Flat shelf

Fig.2-35

Shelf guard

Front

Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig.2-36).

Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward
(Fig.2-37).

To ret the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig.2-38).

Oven Shelves – Right-hand (Tall) Oven

The tall oven is supplied with four at cooking shelves
(Fig.2-39) and a plate warming shelf (Fig.2-40).

When using the tall oven, you can cook on all shelves at the
same time, but make sure that they are well spaced out allow
the hot air to circulate.

The Handyrack (Main Oven)

The Handyrack (Fig.2-41) ts to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.

The maximum weight that can be held by the Handyrack
is 5.5 kg (12 lb). It should only be used with the supplied
roasting tin, which is designed to t the Handyrack. Any other
vessel could be unstable.

It can be tted at two dierent heights. One of the oven
shelves must be removed and the other positioned to suit.

Drop shelf

Front

Shelf guard

Fig.2-36 Fig.2-37

ArtNo.320-0011 Removing the shelf 1

Fig.2-38

ArtNo.324-0002 Oven shelf

Fig.2-40

Fig.2-39

Fig.2-41

When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.

When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.

To t the Handyrack, locate one side of it on the door bracket
(Fig.2-42). Then spring the other side out to clip it onto the
other bracket (Fig.2-43).

Main Oven Light

Press the button to turn the light on (Fig.2-44).

If the oven light fails, turn o the power supply before
changing the bulb. See the ‘Troubleshooting’ section for
details on how to change the bulb.

11

ArtNo.324-0010 Plate warming shelf

Fig.2-42

ArtNo.320-0015

Fitting the Handyack 1

ArtNo.320-0017
Main oven light

Fig.2-43

ArtNo.320-0016

Fig.2-44

3. Cooking Tips

Tips on Cooking with the Timer

If you want to cook more than one dish, choose dishes that
require approximately the same cooking time. However,
dishes can be ‘slowed down’ slightly by using small containers
and covering them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or placing them in
larger containers.

Very perishable foods such as pork or sh should be avoided
if a long delay period is planned, especially in hot weather.

DO NOT place warm food in the oven to be timed.



DO NOT use a timed oven that is already warm.



DO NOT use the timed oven if the adjoining oven is



already warm.

Whole poultry must be thoroughly defrosted before being
placed in the oven. Check that meat and poultry are fully
cooked before serving.

General Oven Tips

The wire shelves should always be pushed rmly to the back
of the oven.

Baking trays with food cooking on them should be placed
level with the front edge of the oven’s wire shelves. Other
containers should be placed centrally. Keep all trays and
containers away from the back of the oven, as overbrowning
of the food may occur.

For even browning, the maximum recommended size of a
baking tray is 340 mm (13½”) by 340 mm (13½”) in the main
oven and 232 mm (9

When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.

• Always leave a “finger’s width” between dishes on
the same shelf. This allows the heat to circulate freely
around them.

• To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.

• Where dishes may boil and spill over during cooking,
place them on a baking tray.

• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your
Cooker’) work better when fat splashes are avoided.

Cover meat when cooking.

• Sufficient heat rises out of the oven while cooking to
warm plates in the grill compartment.

• If you want to brown the base of a pastry dish, preheat
the baking tray for 15 minutes before placing the dish in
the centre of the tray.

1

/8”) and 321 mm (125/8”) in the tall oven.

12

4. Cooking Table

DocNo.031-0004 - Cooking table - electric & fan single cavity

The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a
preferred result.

Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The
temperature in the fan oven does not vary with height in the oven so you can use any shelf.

Conventional Oven

Food
Meat

Beef (no bone)

Lamb

Pork

Poultry

Chicken

Turkey

Duck

Casserole
Yorkshire Pudding
Cake

Very rich fruit - Christmas,
wedding, etc.
Fruit 180 mm tin
Fruit 230 mm tin
Madeira 180 mm
Queen cakes
Scones
Victoria sandwich
180 mm tin
210 mm tin

Desserts

Shortcrust tarts
Fruit pies
Tartlets
Puff pastry
Meringues
Baked egg custard
Baked sponge pudding
Milk pudding

Bread
Fish

Fillet
Whole
Steak

Temperature °C
(Shelf Position)

160 (C)

200 (C)
160 (C)
200 (C)
160 (C)
200 (C)

160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)

140-150 (C)

220 (C)

140 (C/B)

150 (C/B)
150 (C/B)
160 (C/B)
190 (C/B)
220 (C/B)

180 (C/B)
180 (C/B)

200 (C/B)
200 (C/B)
200 (C/B)
210 (C/B)
100 (C/B)
160 (C/B)
180 (C/B)

140-150 (C/B)

210 (C)

Fanned Grilling

190 (C/B)
190 (C/B)
190 (C/B)

Fan Oven

Temperature

°C

150
190
150
190
150
190

150
190
150
190
150
190

130-140

210

130

140
140
150
180
210

170
170

190
190
190
200

90
150
170

130-140

200

190 (C/B)
190 (C/B)
190 (C/B)

Approximate Cooking Time

ArtNo.050-0001 Gas cooking table

30-35 minutes per 500g +30-35 minutes.
20-25 minutes per 500g +20-25 minutes.
30-35 minutes per 500g +30-35 minutes.
25-30 minutes per 500g +25-30 minutes.
35-40 minutes per 500g +35-40 minutes.
25-30 minutes per 500g +25-30 minutes.

20-25 minutes per 500g +20-25 minutes.
15-20 minutes per 500g +15-20 minutes.
20 minutes per 500g +20 minutes.
15 minutes per 500g +15 minutes.
25-30 minutes per 500g.
20 minutes per 500g.
2-4 hours according to recipe.
Large tins 30-35 minutes; individual 10-20 minutes.

45-50 minutes per 500g of mixture.

2-2½ hours.
Up to 3½ hours.
80-90 minutes.
15-25 minutes.
10-15 minutes.

20-30 minutes.
30-40 minutes.

20-30 minutes on a preheated tray.
35-45 minutes.
10-20 minutes according to size.
20-40 minutes according to size.
2-3 hours.
45-60 minutes.
40-45 minutes.
2 to 3 hours.
20-30 minutes.

15-20 minutes.
15-20 minutes per 500g.
Steaks according to thickness.

Top (T)

Centre (C)

Base (B)

ArtNo.050-0007

Oven shelf positions

Oven Shelf Positions

T - Top; C - Centre; B - Base

Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
220°C (210°C for fan oven) and the
cooking time adjusted accordingly.
For stuffed and rolled meats, add
approximately 10 minutes per 500g,
or cook at 200°C (190°C) for 20
minutes then 160°C (150°C) for the
remainder.

For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.

Using the conventional oven: when
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.

Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.

Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340 mm
x 340 mm. This ensures free heat
circulation.
If cooking a two tier load, the trays
should be interchanged
approximately halfway though the
cooking time.

13

5. Cleaning Your Cooker

Fig.5-1

Fig.5-2

A

B

D

ArtNo.311-0032 Burner layout FSD

A – Cap, B – Head, C – Notch, D – Base, E – Electrode

A

C

E

B

C

D

ArtNo.311-0033 Wok burner details FSD

E

A – Inner burner cap, B – Outer burner cap, C – Inner burner head,

D – Outer burner head, E – Wok burner base

Fig.5-3

Essential Information

Isolate the electricity supply before carrying out any
thorough cleaning. Allow the cooker to cool.

NEVER use paint solvents, washing soda, caustic



cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.

DO NOT mix dierent cleaning products – they may



react together with hazardous results.

All parts of the cooker can be cleaned with hot soapy water
– but take care that no surplus water seeps into the

appliance.

Remember to switch on the electricity supply and reset the
clock before re-using the cooker.

Hotplate Burners

The burner heads and caps can be removed for cleaning.

DO NOT put the burner heads in a dishwasher.



Make sure they are absolutely dry before replacing them.

The Single Ring Burners

When retting the burner head, make sure that the notch
lines up with the electrode or hole in the base. Check that the
burner head is level and that the cap is tted centrally on the
burner head (Fig.5-1).

The Wok Burner

The wok burner can also be taken apart for cleaning.

When reassembling the wok burner (Fig.5-2), turn over the
large base ring and nd the ‘D’ shaped area (Fig.5-3). Turn the
head until the ‘D’ matches the one on the burner base. Flip
the burner over once again and place it on the burner base.

To t the small inner burner, nd the larger electrode notch in
the burner rim. Line this up with the white ignition electrode
and place the inner burner on the large base ring (Fig.5-4).

Fig.5-4

B

A

ArtNo.311-0016 Fitting the burner inner head

A – Electrode notch, B – Ignition electrode

Now t the two burner caps, making sure that they are seated
properly.

Check the burner ports are not blocked. If a blockage occurs,
remove stubborn particles using a piece of fuse wire.

The Wok Cradle

Recommended cleaning materials are hot soapy water, a
moistened soap pad, cream cleaner or a nylon scourer.

14

The Griddle

Always clean the griddle after use. Allow it to cool completely
before removing. Immerse the griddle plate in hot soapy
water. Use a soft cloth or, for stubborn stains, a nylon washing
up brush.

Note: If the griddle is washed in a dishwasher then some
dishwasher residue may appear on the back. This is normal
and will not aect the performance of your griddle.

Fig.5-5

Glide-out Grill

Before you remove any of the grill parts for cleaning.



make sure that they are cool, or use oven gloves.

The grill pan and trivet should be washed in hot soapy water.
Alternatively, the grill pan can be washed in a dishwasher.

After grilling meats or any foods that soil, leave to soak for
a few minutes in the sink immediately after use. Stubborn
particles may be removed from the trivet by using a nylon
brush.

The grill pan can be easily removed for cleaning as follows:

Remove the grill pan support frame by pulling the grill pan
forward (Fig.5-5).

Lift the grill pan clear of the support frame.
is held to the side rails by two clips on each side (Fig.5-6).

For each side, support the side rail with one hand and with
the other hand lift the frame up and out of the side clips
(Fig.5-7).

For safety, push the side rails back into the grill chamber.

If you need to remove the side rails to allow cleaning of the
grill chamber, you can unhook them from the grill chamber
sides (Fig.5-8) and wipe the sides clean with a soft cloth and
mild detergent.

The support frame

ArtNo.331-0001Grill pan pulled forwards

ArtNo.331-0003 Grill frame out, no pan

ArtNo.331-0004 Removing the grill frame

Fig.5-6

Fig.5-7

DO NOT put the side runners in a dishwasher.

Once you have nished, hook the side rails back onto the
sides of the chamber. To ret the frame, pull the side rails
forward and, for each side in turn, support the side rail and
press the frame down into the side rails.

Replace the grill pan. When retting the grill pan, make sure
that the wide rim is at the front (Fig.5-9).

Control Panel and Doors

Avoid using any abrasive cleaners including cream cleaners.
For best results, use a liquid detergent.

The same cleaner can be used on the doors, or alternatively,
using a soft cloth wrung out in clean hot soapy water – but
take care that no surplus water seeps into the appliance.

After cleaning, polish with a dry cloth.

Fig.5-8

ArtNo.331-0005 Removing the grill rail

Fig.5-9

ArtNo.331-0006 Grill pan plan

15

Fig.5-10

Fig.5-11

Ovens

‘Cook & Clean’ Panels

The main oven has panels which have been coated with a
special enamel that partly cleans itself. This does not stop
all marks on the lining, but helps to reduce the amount of
manual cleaning needed.

The ‘Cook & Clean’ panels work better above 200 °C. If you do
most of your cooking below this temperature, occasionally
remove the panels and wipe with a lint free cloth and hot
soapy water. The panels should then be dried and replaced
and the oven heated at 200 °C for about one hour. This
will make sure that the ‘Cook & Clean’ panels are working
eectively.

DO NOT use steel wool, oven cleaning pads, or any other

materials that will scratch the surface.

ArtNo.320-0022 Tall oven side support

Removing the Main Oven Linings

Some of the lining panels can be removed for cleaning.

If you wish to clean the enamel interior of the oven, you
will need to remove the shelves before removing the ‘Cook
& Clean’ panels. You do not have to remove the support
brackets to remove the panels. Lift each panel upward and
slide forward o the support brackets (Fig.5-10).

Once the panels have been removed, the oven enamel
interior can be cleaned.

Ret in the reverse order.

The Tall Oven

To clean the oven sides, slide out the shelves, unhook the
supports from the oven sides, and lift out (Fig.5-11).

16

Cleaning Table

Cleaners listed (Table 5-1) are available from supermarkets or
electrical retailers as stated.

For enamelled surfaces use a cleaner that is approved for use
on vitreous enamel.

Regular cleaning is recommended. For easier cleaning, wipe
up any spillages immediately.

Hotplate

Part Finish Recommended Cleaning Method

Hob top (including burner heads and
caps)

Ceramic/Induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.

Griddle plate (some models only) Non-stick surface

Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Outside of Cooker

Part Finish Recommended Cleaning Method

Door, door surround and storage
drawer exterior

Sides and plinth Painted surface Hot soapy water, soft cloth.

Enamel, stainless steel,
aluminium

Enamel or paint

Stainless steel

Hot soapy water, soft cloth. Any stubborn stains remove gently
with a nylon scourer.

Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.

Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.

E-cloth (electrical retailers) or microfibre all-purpose cloth
(supermarket).

Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.

Control panel Paint, enamel or stainless steel Warm soapy water. Do not use abrasive cleaners on lettering.

Plastic/chrome, copper or

Control knobs/handles & trims

Oven door glass/glass lid Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

lacquered brass

Brass Brass polish.

Warm soapy water, soft cloth.

Oven and Grill

Part Finish Recommended Cleaning Method

Sides, floor & roof of oven NOT
COOK & CLEAN OVEN PANELS (see
below)

Cook & Clean oven panels (some
models only)

Oven shelves, Handyrack, grill
trivet, Handygrill rack (some
models only)

Grill pan/meat tin (some models
only)

Enamel

Special enamel that partly
cleans itself

Chrome

Enamel Hot soapy water. Soap filled pad. Dishwasher.

Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW

MANUFACTURER’S INSTRUCTIONS.
Do not allow contact with the oven elements.
This surface cleans itself at 200 °C and above, or the panels can be

removed and washed with hot soapy water and a nylon brush (see
‘The Ovens’ in ‘Cleaning your Cooker’).

An oven interior cleaner that is suitable for chrome. Soap filled
pad. Dishwasher.

Table 5-1

17

6. Troubleshooting

Hotplate ignition or hotplate burners faulty

Is the power on? Is the clock illuminated?

If not, there maybe something wrong with the power
supply.

Are the sparker (ignition electrode) or burner slots
blocked by debris?

Are the burner trim and caps correctly located? See the
section on ‘Cleaning’.

Hotplate burners will not light

Make sure that the burner parts have been replaced
correctly after wiping or removing for cleaning.

Check that there is not a problem with your gas
supply. You can do this by making sure that other gas
appliances you may have are working.

Do the burners spark when you push the button?

If not, verify that the power is on by checking that the
clock is illuminated.

Steam is coming from the oven

When cooking foods with high water content (e.g. oven
fries) there may be some steam visible at the rear grille.

Power failure

In the event of a failure in the electrical supply,
remember to reset the clock to make sure that the
timed oven continues to operate.

Food is cooking too slowly, too quickly, or burning

Cooking times may dier from your previous oven.

Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide. The oven control settings and cooking
times are intended to be used only as a guide.

Individual tastes may require the temperature to be
altered either way, to get the results you want.

The oven is not cooking evenly

Do not use a baking tray with dimensions larger than
those specied in the section on ‘General Oven Tips’.

If you are cooking a large item, be prepared to turn it
round during cooking.

If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, make sure that it is placed centrally on the
shelf.

Take care when opening the oven door, as there may
be a momentary pu of steam when the oven door
is opened. Stand well back and allow any steam to
disperse.

What cleaning materials are recommended for the
cooker?

See the ‘Cleaning’ section for recommended cleaning
materials.

Never use caustic or abrasive cleaners as these will



damage the surface.

An oven fan is noisy

The note of the oven fan may change as the oven heats
up – this is perfectly normal.

The knobs get hot when I use the oven or the grill. Can I
avoid this?

Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open.

Make sure that the grill pan is pushed right back to the
‘back stop’ when grilling.

Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held rmly
against the seal.

A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level arrange for
your supplier to level it for you.

Oven not coming on

Is the power on? Is the clock illuminated? If not, there
may be something wrong with the power supply.

Is the cooker supply on at the isolator switch?

Has the time of day been set?

Is the key symbol [
that the oven is locked? See the ‘Clock’ section of the
instructions for more information on the key lock
feature.

The timed oven is not coming on when automatic cooking

Has the oven knob been left in the OFF position by
mistake?

F ] showing in the display to signify

Always grill with the grill compartment door open.

If there is an installation problem and I don’t get my
original installer to come back to x it who pays?

You do. Service organizations will charge for their call
outs if they are correcting work carried out by your
original installer. It is in your interest to track down your
original installer.

Is the oven locked (see above)?

Oven temperature getting hotter as the cooker gets older

If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be tted by a service person.

18

An oven light is not working

The bulb has probably burnt out. You can buy a
replacement bulb (which is not covered under the
warranty) from a good electrical shop. Ask for a 15 W –
230 V lamp, FOR OVENS. It must be a special bulb, heat
resistant to 300 °C (Fig.6-1).

Turn o the power at the circuit breaker.

Before removing the existing bulb, turn o the power
supply and make sure that the oven is cool. Open the
oven door and remove the oven shelves.

Unscrew the bulb cover by turning counter-clockwise. It
may be very sti (Fig.6-2).

Taking care to protect your ngers with a glove in case
the bulb should shatter, unscrew the old bulb.

Screw in the new bulb; screw back the bulb cover. Turn
on the circuit breaker and check that the bulb now
lights.

The oven door is misaligned

The bottom hinge of either oven door can be adjusted
to alter the angle of the door (Fig.6-3). Loosen the
bottom hinge xing screws and use the notch and a at
bladed screwdriver to move the position of the hinge to
set the hinge position (Fig.6-4).

Fig.6-1

ArtNo.324-0005 Oven light bulb

Fig.6-2

ArtNo.324-0007 Unscrewing the bulb cover

Fig.6-3

Retighten the hinge screws.

Eect of hinge adjustment – exaggerated for clarity

Centre line of hinge pin

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

Fig.6-4

19

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

7. Installation

Service and Spares

Firstly, please complete the appliance details below and keep them safe for future reference – this information will enable us
to accurately identify the particular appliance and help us to help you. Filling this in now will save time and inconvenience
if you later have a problem with the appliance. It may also be of benet to keep your purchase receipt with this leaet. You
may be required to produce the receipt to validate a warranty eld visit.

Retailer’s Name and Address Andi-Co Australia Pty Ltd.

1 Stamford Road,
Oakleigh,
VIC 3166

Customer Care:
Tel: [phone]
Email: [e-mail]

Name of Appliance Classic Deluxe 90 Dual Fuel

Appliance Serial Number*

Fuel Type Dual Fuel

Date of Purchase

Installer’s Name, Address and
Telephone No.

Date of Installation

* This information is on the appliance data badge.

If you Have a Problem

In the unlikely event that you have a problem with your appliance, please refer to rest of this booklet, especially the problem
solving section, rst to check that you are using the appliance correctly.

If you are still having diculty, contact Customer Care on 1300 650 020 or email [e-mail].

Please Note

For warranty information and how to request a remedy please refer to the warranty document provided with

the appliance or contact Customer Care.

Out of Warranty

We recommend that our appliances are serviced regularly throughout their life to maintain the best performance and
eciency. The frequency of service will depend on usage – for normal usage once a year should suce.

Service work should only be carried out by a suitably Authorised Person.

Spare Parts

To maintain optimum and safe performance, we recommend that only genuine spare parts are used. Do not use re­conditioned or unauthorised controls. Contact Spare Parts on [phone] or email [e-mail].

20

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Dear Installer

Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.

Installer’s Name

Installer’s Company

ArtNo.050-0011 - Installer information table

Installer’s Telephone Number

Appliance Serial Number

You must be aware of the following safety requirements &
regulations.

Prior to installation, make sure that the local distribution
conditions (nature of the gas and gas pressure) and the
adjustment of the appliance are compatible.

Provision of Ventilation

This appliance is not connected to a combustion products
evacuation device. Particular attention shall be given to the
relevant requirements regarding ventilation.

The room containing the cooker should have an adequate air
supply.

Install the cooker in a location to allow the complete
combustion of gas, proper ueing and to maintain ambient
temperature of the immediate surroundings at safe limits,
under normal condition.

Location of Cooker

The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.

Note: An appliance for use on Propane must not be installed
in a room or internal space below ground level, e.g. in a
basement.

Conversion

All models are supplied set for use on Natural gas. A
conversion kit for Propane gas is included with the appliance.

After converting the appliance, please attach the Gas
Conversion sticker over the appropriate area of the data
badge – this will identify the gas type for which the appliance
is now set.

The appliance must be installed in accordance with the
regulations in force and only in a well ventilated space.

Read the instructions before installing or using this
appliance.

The regulations and standards are as follows:

AS 5601 – ‘Gas Installations’

In your own interest and that of safety, it is law that all gas
appliances be installed by competent persons.

Failure to install the appliance correctly could



invalidate any warranty or liability claims and lead
to prosecution.

The cooker must be installed in accordance with all local gas
tting regulations, municipal building codes, electrical wiring
regulations and any other relevant statutory regulations.

WARNING!



Where this appliance is installed in a marine craft,
caravan or mobile home, it shall NOT be used as a
space heater.

21

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

cooker installation satisfactorily:

• Stability bracket: If the cooker is to be supplied with
gas through a flexible hose, a stability bracket or chain
MUST be fitted.
These are not supplied with the cooker but are
available at most builders’ merchants.

• Gas pressure tester/manometer.

• Flexible gas hose: Must be in accordance with the

relevant standards.

• Multimeter: For electrical checks.

Checking the Parts:You will need the following equipment to complete the

3 pan supports Griddle plate

ArtNo.000-0001 90 Pan supports

Wok cradle Grill pan & trivet

You will also need the following tools:

Electric drill

1.

2. Masonry drill bit (only required if tting the cooker on a

stone or concrete oor)

3. Wall plugs (only required if tting the cooker on a stone

or concrete oor)

4. Steel tape measure

5. Cross head screwdriver

6. Flat head screwdriver

7. Spirit level

8. Pencil

9. Adjustable spanner

10. Screws for tting stability bracket

11. 4 mm & 3 mm Allen keys

12. 13 mm spanner or socket wrench

ArtNo.000-0009 Wok ring, cast

ArtNo.330-0001 - Grill pan

1 at shelf & 1 drop shelf Handyrack

ArtNo.324-0003 Handyrack

Roasting tin Tall oven shelves & shelf supports

ArtNo.324-0004 Roasting tin

ArtNo.000-0010 Tall oven shelves

Splashback Plinth

ArtNo.421-0002 - Splashback

Stability bracket Restraining chain & hook

22

ArtNo.020-0021 - Restraining
chain & hook

INSTALLATION

130 mm min

ArtNo.090-0009 - 90 2BC cooker min spacings

75 mm

min

75 mm

min

650 mm

min

905 mm min
930 mm max

Check the appliance is electrically safe and gas sound when you have nished.

Positioning the Cooker

Fig.7-1 shows the minimum recommended distance from the
cooker to nearby surfaces.

The cooker should not be placed on a base.

Above hotplate surround should be level with, or above, any
adjacent work surface.

A gap of 75 mm should be left between each side of the
cooker ABOVE the hotplate level and any adjacent vertical
surface.

For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25 mm.

A minimum space of 650 mm is required between the top of
the hotplate and a horizontal combustible surface.

Fig.7-2 shows the suggested clearances above the cooker.

*Any cookerhood should be installed in accordance with the
hood manufacturer’s instructions.

**Any splashback must be tted in accordance with the
manufacturers instructions. Allowance should be made for the
additional height of the ue trim, which is tted to the cooker
hob.

410 mm min

Fig.7-1

Fig.7-2

910 mm min*

ArtNo.090-0012 Min positions above cooker

**

Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration.

We cannot accept responsibility for damage caused by
normal use of the cooker to any material that de-laminates
or discolours at temperatures less than 65 °C above room
temperature

We recommend a gap of 910 mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.

If the cooker is near a corner of the kitchen, a clearance of
130 mm is required to allow the oven doors to open
(Fig.7-3). The actual opening of the doors is slightly less but
this allows for some protection of your hand as you open the
door.

Moving the Cooker

On no account try and move the cooker while it is



plugged into the electricity supply.

The cooker is very heavy, so take great care.



We recommend that two people manoeuvre the cooker.
Make sure that the oor covering is rmly xed, or removed,
to prevent it being disturbed when moving the cooker
around.

To help you, there are two levelling rollers at the back, and
two screw-down levelling feet at the front.

Fig.7-3

Fig.7-4

Remove the polystyrene base pack. From the front, tilt
the cooker backwards and remove the front half of the
polystyrene base (Fig.7-4). Repeat from the back and remove
the rear half of the polystyrene base.

23

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-5

Fig.7-6

Fig.7-7

ArtNo.010-0004 Moving the cooker

Stability bracket

ArtNo.070-0014 - Stability bracket - Wall fitting

3 mm min

Cooker

Floor

Lowering the Two Rear Rollers

To adjust the height of the rear of the cooker, rst t a 13
mm spanner or socket wrench onto the hexagonal adjusting
nut (Fig.7-5). Rotate the nut – clockwise to raise – counter­clockwise to lower.

Make 10 complete (360°) turns clockwise.

Make sure you lower BOTH REAR ROLLERS.

Completing the Move

Unfold the rear edge of the cardboard base tray. Open the
grill door and right-hand oven door so that you can get a
good grip on the bottom of the fascia panel as you move the
oven (Fig.7-6).

Carefully push the cooker backwards o the cardboard base.
Remove the base tray.

Position the cooker close to its nal position, leaving just
enough space to get behind it.

DO NOT use the door handles or control knobs to



manoeuvre the cooker.

Fitting the Stability Bracket and Chain

A stability bracket and chain MUST be tted when



the cooker is connected to a exible gas supply.

Unless properly installed, the cooker could be tipped by
leaning on the door. Injury might result from spilled hot
liquids or from the cooker itself.

IMPORTANT: The cooker must be set to the correct height
and levelled before the stability bracket is installed.

Fig.7-8

Fig.7-9

Typical oor mounting

Outer stability

bracket

3 mm min

Wall

Typical wall mounting

Restraining

chain

ArtNo.011-0007 - Restraining chain (AUS)

Cooker

Floor

Fitting a Stability Bracket

When tting a stability bracket please refer to the instructions
supplied with the bracket for further details on tting.

When tting a stability bracket (Fig.7-7 and Fig.7-8) adjust
the bracket to give the smallest practicable clearance
between the bracket and the engagement slot in the rear of
the cooker.

Fit the bracket so that it engages as far as possible over the
chassis of the cooker.

Fitting the Restraining Chain

The restraining chain MUST be tted.

The length of chain between the appliance and the wall xing
should prevent strain on the gas and electricity connections,
but still allow access to unhook the chain when the cooker is
pull forward.

Measure the length of chain required. Use the clamp supplied
to clamp onto the gas pipe (Fig.7-9). Fix the supplied hook
securely to the wall.

24

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Repositioning the Cooker Following
Connection

If you need to move the cooker once it has been connected
then you need to unplug it and, having gripped under the
fascia panel and lifted the front of the cooker slightly
(Fig.7-6), you need to check behind the cooker to make sure
that the gas hose is not caught.

As you progress, make sure that both the electricity cable and
gas hose always have sucient slack to allow the cooker to
move.

With a stability chain tted, release it as you ease the cooker out.
Do not forget to ret it when you replace the cooker.

When you replace the cooker, again check behind to make
sure that the electricity cable and gas hose are not caught or
trapped.

Levelling

You are recommended to use a spirit level on a shelf in one of
the ovens to check for level.

Place the cooker in its intended position taking care not to
twist it within the gap between the kitchen units as damage
may occur to the cooker or the units.

The front feet and rear rollers can be adjusted to level the
cooker.

To adjust the height of the rear of the cooker use a 13 mm
spanner or socket wrench to turn the adjusting nuts at the
front bottom corners of the cooker.

To set the front turn the feet bases to raise or lower.

25

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-10

240

100

100

300

ArtNo.090-0027 - 90 Elan gas connections

All dimensions in millimetres

Gas inlet

Gas Connection

Must be in accordance with the relevant standards.

The gas supply needs to terminate with a threaded tting ½”.
The inlet connector is located just below the hotplate level at
the rear of the cooker.

Because the height of the cooker can be adjusted and
each connection is dierent it is dicult to give precise
dimensions. Ideally, the house supply connection should be
in the shaded area (Fig.7-10).

Means of isolation must be provided at the supply point by
either an approved quick-connect device or a Type 1 manual
shut-o valve.

The hose should be tted so that both inlet and outlet
connections are vertical so that the hose hangs downwards in
a ‘U’ shape (Fig.7-10).

A exible connection is supplied with the cooker. If it is
necessary to use another hose it must be to AS 1869 Class
B and be suitable for your gas type. If in doubt contact your
supplier. Screw connect the threaded end of the hose into the
gas inlet.

After completing the gas connection, check the cooker is gas
sound with a pressure test. When checking for gas leaks do
not use washing up liquid – this can corrode. Use a product
specically manufactured for leak detection.

Natural Gas

The adjustable spring loaded gas pressure regulator is preset
to give a nominal pressure of 1 kPa on Natural gas. Connect to
the Rp½ inlet on the underside of the pressure regulator.

Propane

This cooker is supplied ready for use on Natural gas. A
conversion kit for Propane gas is supplied with the cooker –
see the ‘Conversion to Propane Gas’ section.

Pressure Testing

The pressure test point is accessible on the inlet pipe at the
rear. Remove the test nipple screw and t a pressure gauge to
the test point. Turn on and light two of the hotplate burners.

For Natural Gas cookers the pressure should be between

0.95kPa and 1.0kPa.

For Propane X cookers the pressure should be 2.54 kPa.

26

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Electrical Connection

This appliance must be installed by a qualied electrician
to comply with the relevant regulations
(AS/NZS 60335.2.6) and also the local electricity supply
company requirements.

Make sure that the mains characteristics (voltage, nominal,
power, etc.) match the ratings indicated on the cooker data
plate.

Current Operated Earth Leakage Breakers

The combined use of your cooker and other domestic

appliances may cause nuisance tripping, so we

recommend that the cooker is protected on an individual

RCD (Residual Current Device) or RCBO (Residual Current

Breaker with Overload).

IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED

ELECTRICIAN.

The cooker is preset for a single-phase earthed electrical
connection. It is essential to install a multi-pole circuit breaker
that completely disconnects the appliance from the mains,
with a minimum contact break distance of 3 mm.

WARNING: THIS APPLIANCE MUST BE EARTHED.



The appliance must be connected to an ecient earthing
circuit. If the electricity network is not equipped with an
earth connection, then it must be installed separately in
compliance with local regulations.

Earthing is a safety measure required by law, and must be
performed with particular care by a qualied technician,
who must also check that the electricity supply
characteristics are correct.

Fig.7-11

ArtNo.132-0001 - 1 phase 240Vac 50Hz

1-phase 220-240 VAC 50 Hz

Fig.7-12

ArtNo.132-0003 - Single-phase connections (AUS)

A N

Fig.7-13

The total electrical load of the appliance is approximately

8.6 kW. The cable size used should be suitable for this load

and comply with all local requirements (i.e. PVC Insulated
cable IEC 60227 – code 53 for ordinary cables).

Please note the maximum cable sizes are 6 mm² for the screw
terminals and 10 mm² for the 3-pronged links.

Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect the
mains cable to the correct terminals for your electrical supply
type (Fig.7-11 and Fig.7-12).
tted and that the terminal screws are tight. Secure the mains
cable using the cable clamp.

Check that the links are correctly

Fixed Wiring

For connection to xed wiring, i.e. exible conduit, remove
the electrical terminal cover box on the back panel. Using the
two screws, x the strain relief bracket in position.

Fix the conduit-to-conduit mounting bracket onto the
strain relief bracket. Connect the mains cable to the correct
terminals for your electrical supply type (Fig.7-13 and
Fig.7-14). Check that the links are correctly tted and that the
terminal screws are tight.

Replace the electric terminal cover box; make sure that the
conduit is clear of the bottom ange.

ArtNo.132-0002 - 3 phase 240/415Vac 50Hz

3-phase 400-415 VAC 50 Hz

Mains terminal

AN

Fixing bracket for

conduit connection

Cable clamp

ArtNo.132-0005 - Fixed wiring connection 2 (AUS)

Conduit

Fig.7-14

27

INSTALLATION

ArtNo.350-0011 - Fitting the plinth 2 (Kitchener)

Outer plinth

Outer plinth xing screw

Inner plinth

ArtNo.215-0026 - Handle gaskets fixed

Art No 215-0028 - Handrail fascia fixings

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-15

Fig.7-16

Fig.7-17

ArtNo.350-0010 - Fitting the plinth 1 (Kitchener)

Final Checks

Hotplate Check

Check each burner in turn (refer to the ‘Hotplate Burners’
section at the front of the instructions).

Grill Check

Turn on the grill control and check that the grill heats up.

Oven Check

Set the clock as described earlier in the instructions, and then
turn on the ovens. Check that the oven fans start to turn and
that the ovens start to heat up.

Note: The oven light bulb is not included in the guarantee.

Turn o the oven.

Final Fitting

Fitting the Handles and Handrail

Remove the 4 mm Allen screws from the doors (Fig.7-15). Fit
the door handles and secure using the 4 mm screws.

The handles should be above the xings.



Remove the 4 mm Allen screws from the top corners of the
fascia (Fig.7-16). Fit the front handrail in position and secure
using the 4 mm screws.

Fig.7-18

Fitting the Plinth

Fit the inner plinth to the bottom front of the cooker using
the 4 screws provided (Fig.7-17).

Fit the outer plinth (2 screws, 1 each end) to the inner plinth.
The height of the outer plinth can be adjusted by sliding it up
or down via the slotted hole (Fig.7-18).

Fitting the Splashback

Position the splashback on the rear of the hotplate and secure
with the screws supplied.

Customer Care

Installer: Please complete your details in this guide, inform
the user how to operate the cooker and hand over the
instructions.

Thank you.

28

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Art No 215-0028 - Handrail fascia fixings

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

8. Conversion to LP Gas

Conversion from Natural Gas (1.0 kPa)
to LPG X Propane (2.54 kPa)

This conversion must be performed by a competent



person, in accordance with these instructions and
with the local supply company requirements. Read
the instructions before converting this appliance.

Failure to convert the appliance correctly could



invalidate any warranty or liability claims and lead
to prosecution.

The conversion instructions must be used in



conjunction with the rest of the appliance
instruction, in particular for information on
Standards, cooker positioning, connection, hose
suitability, etc.

When servicing or replacing gas-carrying



components, disconnect from the gas before
starting, and check that the appliance is gas sound
after completion.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity supply before



conversion. Before electrical reconnection, check
that the appliance is electrically safe.

B

A

ArtNo.311-0010 Injectors

A – Jet, B – Internal injector, C – External injector

C

Fig.8-1

Fig.8-2

Fig.8-3

Injectors

Remove the burner caps and heads. Remove the old jets.
Fit the new jets: see ‘Technical Data’ section for correct jets.
Reassemble in the reverse order (Fig.8-1).

Tap Adjustment

Removing the Handrail

Remove the handrail. Now remove the 2 cross-headed screws
hidden behind the handrail end brackets (Fig.8-2).

Removing the Control Panel

Pull o all the control knobs and remove the 3 xing screws
underneath the control panel (Fig.8-3).

The control panel will drop down slightly. It is held at the top
by two holes in the top edge, one at each end, that locate on
the tags on the inner panel. Lift the control panel clear of the
tags and pull forwards, taking care not to damage or strain
the wiring.

Bypass Screw Adjustment

Turn the bypass screw on each control clockwise to the stop
(Fig.8-4). Ret the control panel.

ArtNo.270-0032 - 90 Prof+ FX - Removing the control panel

Control panel may dier from that shown

Fig.8-4

ArtNo.0102-0011 - Screwing

the control valve bypass screw

29

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.103-0006 - Maxitrol cap & converter

Nut

Snap-in converter device

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

Fig.8-5

Fig.8-6

ArtNo.102-0007 - Maxitrol converter device positions

Set the Governor

Unscrew the governor’s brass top. In the base of the brass top
is a plastic snap-in converter device (Fig.8-5). To convert the
governor, snap the device out of the top and ret it the other
way round. The snap-in converter device is marked to show
the gas for which it is set (Fig.8-6).

Make sure the device is secure in the top cap and ret the cap
to the governor.

Pressure Testing

The pressure test point is accessible on the inlet pipe at the
rear. Remove the test nipple screw and t a pressure gauge to
the test point. Turn on and light two of the hotplate burners.

For Propane X cookers the pressure should be 2.54 kPa.

Make sure that the appliance is gas sound.



Check the operation of all the burners.



Affix Label

Stick the appropriate gas label over the natural gas part of the
appliance data label.

30

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Art No 215-0028 - Handrail fascia fixings

ArtNo.210-0009 - Classic
removing the handles

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

9. Servicing

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS TURN OFF THE GAS SUPPLY

Check the appliance is gas sound after completion



of service. When checking for gas leaks DO NOT use
washing up liquid – this can corrode. Use a product
specically manufactured for leak detection.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity supply before



servicing, particularly before removing any of the
following: control panel, side panels, hotplate tray
or any electrical components or covers.

Before electrical reconnection, check that the



appliance is electrically safe.

1 Panels & Handrails

1.1 To Remove the Handrail

Remove the plastic blanking plugs (Fig.9-1) and remove
the 2 end bracket xing screws.

Fig.9-1

Fig.9-2

1.2 To Remove the Control Panel

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control knobs. Remove the handrail (see

1.1).
Now remove the 2 cross-headed screws hidden behind

the handrail end brackets (Fig.9-2).
Pull o all the control knobs and remove the xing

screws underneath the control panel.
Lift the control panel and pull forwards, taking care not

to damage or strain the wiring.

1.3 To Remove a Side Panel

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2). Pull the cooker
forward. Remove the 4 retaining screws from each
panel (2 at the front and 2 at the rear). The lower front
retaining screws (one each side) are situated beneath
the lower edge at the front corners of the side panels

Reassemble in reverse order.

31

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

Fig.9-3

Fig.9-4

Standard burner

B

A

ArtNo.311-0010 Injectors

A – Injector, B – Internal injector, C – External injector

C

2 Hotplate

2.1 To Remove the Hotplate Top

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the pan supports, hotplate burner caps and
tops. Remove the screws holding the hotplate burners
to the hotplate.

Taking care not to damage the burner electrodes,
carefully lift the hotplate, from underneath disconnect
the earth lead at the right hand rear from the rear cross
member and withdraw the hotplate.

Reassemble in reverse order ensuring that the leads
are reconnected. Take care not to damage the ignition
electrodes of the burners.

It is important that the rear earthing leads are replaced
when the xing screws are retted as they from part of
the cooker earthing.

Check for correct burner operation.

2.2 To Change a Hotplate Tap

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.2 & 2.1).
Unplug the FSD lead from the rear of the tap. Undo

compression tting at the rear of the tap. Remove the
xings that secure the tap to the gas rail. Disconnect the
ignition switch wiring.

Remove the tap. Remove and discard the gasket seal.
Fit new gasket seal to replacement tap. Re-assemble in
reverse order. Check the appliance is gas sound. Check
hotplate ignition.

2.3 To Replace a Hotplate Burner Injector

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the burner cap and head (Fig.9-4). Remove the
old injector. Fit the new injector.

Note: The wok burner has 2 injectors.
Reassemble in reverse order. Check that the appliance is

gas sound.

2.4 To Change a Hotplate Burner Electrode

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Lift o the pan supports and remove the burner cap.
Remove the screw holding the electrode. Pull the
electrode vertically up suciently to grip the lead
between thumb and forenger. Pull o the electrode,
but keep hold of the lead.

Fit the new electrode to the lead. Fix the electrode in
the burner with the screw.

Replace the burner cap. Check the burner ignition.
Replace the pan supports.

32

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

2.5 To Change a Hotplate Burner Thermocouple

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.2 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one

side. Ensure that the thermocouple is cool. Turn the
thermocouple so that the earth lead (no sleeve) is in line
with the slot. Lift the thermocouple clear of the hole.

Reassemble in reverse order.

2.6 To Remove or Change a Hotplate Burner

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the hotplate top (see 2.1). Remove the control
panel (see 1.2).

The burners except the right hand wok burner
are mounted on support struts. For these burners,
disconnect the burner feed pipes at the burner. Remove
the screws at the front and rear holding the support
struts. Lift the strut and burners clear. The burners are
xed to the support struts with 2 screws. Remove the
appropriate burner and t the new one. Reassemble in
reverse order. Check burner operation is satisfactory.

Right hand Wok burner
Disconnect the burner feed pipes at the burner. Fit the

new one and reassemble in reverse order. Check burner
operation is satisfactory.

3 Control

3.1 To Change the Ignition Generator

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Change the hotplate tap as detailed in 2.2

3.2 To Replace the Light Switch

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2).
Note: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the

switch body behind the control panel and twisting
sharply. Remove the switch bezel by folding back its
locking wings and pushing forward.

Fit the new bezel to the control panel by rst lining up
the raised key on its body with the cut-out in the control
panel and pushing it in from the front.

Assemble the new switch to the bezel by lining up the
key sections and pushing home. Fit the new button by
pushing in from the front.

Replace the control panel in reverse order and test for
correct operation.

3.3 To Remove the Electronic Timer

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull o the timer control button(s) and remove the
control panel (see 1.2).

Remove the timer/mounting bracket assembly from the
control panel by removing the xing screws.

Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the
same time pulling the unit forward.

Reassemble in reverse order. When replacing the leads,
refer to the wiring diagram in this manual. Check the
operation of the timer.

4 Grill

4.1 To Replace the Grill Controller

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2) and hotplate top
(see 2.1). Disconnect the wiring from the controller.
Remove the 2 screws holding the controller to the
mounting panel.

Fit the new controller and reassemble in reverse order.
Check for correct operation.

4.2 To Remove the Grill Element

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove grill pan from inside the grill compartment;
remove the enamelled front shield from the grill roof, by
undoing the 2 screws and washers.

Remove the 2 screws and washers securing the grill
element front support. Remove the screws from the grill
element.

Lift the element out carefully, disconnecting the leads
from the element terminals (noting their position).

If it is not possible to disconnect the leads in this way,
pull the cooker forward to gain access to the rear,
remove the screws securing the electric cover to the
back sheet, remove the cover and disconnect the
terminals from the rear.

Fit the new element and reassemble in reverse order.
Check the operation of the grill.

5 Ovens

5.1 To Replace an Oven Thermostat

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the handrail (see 1.1), control panel (see 1.2)
and hotplate top (see 2.1). Open the oven doors and
remove the oven furniture.

Left-hand oven

33

From inside the oven remove the two screws holding
the thermostat phial to the oven fan cover at the rear of
the oven.

Remove the four screws that secure the fan cover

(Fig.9-5) then remove the fan cover.

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

Fig.9-5

Fig.9-6

ArtNo.320-0020 Oven back fixing screws

Thermostat capilary

Earthing plate

Pull cooker forward to gain access to the cover box at
the rear of the cooker. Remove the screws securing the
cover and lift clear. The oven thermostat capillary is
clamped to the oven back sheet with an earthing plate.
Remove the screws and plate (Fig.9-6).

Remove the two screws securing the thermostat body
to the control panel at the front of the cooker. Remove
the assembly.

Fit new thermostat. Reassemble in reverse order.

Ensure that the phial is clipped to the oven back with
the phial centrally positioned between the clips.

Ensure that the thermostat capillary is clamped to the
oven back sheet with an earthing plate.

Check operation of thermostat.

Right-hand oven

From inside the oven remove the two screws holding
the thermostat phial to the oven fan cover at the rear of
the oven.

Remove the four screws that secure the fan cover

(Fig.9-5) then remove the fan cover.

Fig.9-7

Element xing screws

ArtNo.321-0005 Fan oven element

The oven thermostat capillary is clamped to the right
hand rear upright with an earthing plate (Fig.9-6).
Remove the screws and plate.

Feed the thermostat capillary out of the oven.
Disconnect wiring from thermostat. Remove the two
screws holding thermostat to mounting panel. Fit new
thermostat and reassemble in reverse order.

Ensure that the phial is clipped to the oven back with
the phial centrally positioned between the clips.

Ensure that the thermostat capillary is clamped to the
right hand rear upright with an earthing plate.

Check operation of thermostat.

5.2 To Remove an Oven Element Thermal Cut-out

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forward to gain access to the cover
box. Undo the cover screws and lift clear. The cut-out
is located on the earth plate beside the oven element
connections. Disconnect the cut-out wiring. Undo the
xings that secure the cut-out to the earth plate and
remove.

Fit the replacement control and reassemble in reverse
order.

5.3 To Remove an Oven Inner Back

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Open the door and remove the shelves. Remove the
screws and washers securing the inner back to the back
of the oven (Fig.9-5). Carefully lift away the inner back.

Reassemble in reverse order making sure that the
screws and washers are fully tightened.

34

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.322-0002 Oven bottom element access

A

B B

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

5.4 To Remove the Fan Oven Element

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the oven inner back (see 5.3). Remove the 2
screws from the top of the element and the one from
the bottom of the element inside the oven (Fig.9-7).

Lift the element out carefully, disconnecting the
terminals connected to the element (noting their
positions).

If it is not possible to disconnect the leads in this way,
pull the cooker forward to gain access to the rear.

Remove the screws securing the electric cover to the
back sheet, remove the cover and disconnect the
terminals from the rear.

5.5 To Replace an Oven Fan

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forward to gain access to the rear.
Remove the screws securing the electric cover to the
back sheet and remove the cover.

Disconnect the 3 terminals connected to the fan noting
their position. Remove the oven inner back (see 5.3).
Hold the fan blade and remove the centre nut (left-hand
thread) 2 brass washers, fan blade and circlip. Unscrew
the fan retaining nuts and washers (3 o each) and lift
the fan away from the rear of the cooker.

Fit the new fan and reassemble in reverse order. Check
the operation of the oven.

Fig.9-8

5.6 To Remove the Left-hand Oven Bottom and Top
Elements

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Bottom Element

Pull the cooker forward to access the cover boxes at
the rear of the unit. Remove the xings that secure the
cover and lift it clear.

Remove the 2 screws ‘A’ and allow the plate to drop
down (Fig.9-8). Remove the 2 screws ‘B’ lower the upper
plate and remove through the slot in the range back
(Fig.9-8). Undo the terminal connections, noting their
positions. Withdraw the element.

Remove the element screws and withdraw element.
Replace the element and re-assemble parts in reverse
order.

Top Element

Open the left-hand oven door and undo the xings that
secure the heat shield. Remove the top element bracket
xings and withdraw the element.

Replace the element and reassemble parts in reverse
order. Check that the oven operates satisfactorily.

35

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.320-0001 Door hinges



ArtNo.320-0001 Door hinges



Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

Fig.9-9 Fig.9-10

Fig.9-11

ArtNo.320-0007 Oven door hinge adjustment 2

Centreline of hinge pin

Oven door omitted for clarity

Fig.9-12

6 Doors

6.1 To Remove the Grill Door

Remove the left-hand side panel (see 1.3). Remove
the plinth (4 screws) and the central vertical cover
(5screws). Remove the 2 countersunk screws (1 each
side) securing the grill hinge arms to the front of the
grill chamber.

Note: The arms are spring tensioned. Carefully remove
the grill door. Retain the gaskets.

Reassemble in the reverse order, making sure that the
gasket is tted between the hinge arm and the front of
the grill chamber.

6.2 To Replace the Main Oven Door

Open the oven door. Support the door and loosen the
2 screws securing the upper hinge and gasket to the
cooker front (Fig.9-9).

The door is heavy, so take care.



Support the door and remove the screw nearest the
hinge pin (Fig.9-10). Swing the hinge up and away from
the door hinge pin. Lift the door away from the lower
hinge and remove.

Reassemble in reverse order.

ArtNo.320-0006 Oven door hinge adjustment 1

Eect of hinge adjustment – exagerrated for clarity

Fig.9-13

ArtNo.320-0002c

- Oven door side screws (Elan)

Fig.9-14

ArtNo.320-0004 Oven door keep

Fig.9-15

6.3 To Adjust the Main Oven Door Angle

The bottom hinge of either oven door can be adjusted
to alter the angle of the door (Fig.9-11). Loosen the
bottom hinge xing screws and use the notch and a at
bladed screwdriver to move the position of the hinge to
set the hinge position (Fig.9-12).

Retighten the hinge screws.

6.4 To Replace the Main Oven Door Outer Panel

Move the cooker forwards to gain access to the sides.
Open the oven door slightly and remove the 4 front

panel xing screws from the door sides (2 each side),
(Fig.9-13). Carefully lift o the outer door panel.

Remove the door handle from the panel by unscrewing
the 2 retaining nuts.

Fit the door handle to the new panel.
Fit the panel to the door. Reassemble in reverse order.

6.5 To Change the Main Left Hand Oven Door Latch

Remove the main oven door outer panel (see 6.4).
Remove screws ‘B’, which hold the latch assembly to
the inner door panel (Fig.9-14). Fit the new catch and
reassemble in reverse order. Check the door operation.

B

ArtNo.320-0003 Oven door latch

6.6 To Adjust the Main Left Hand Oven Door Catch
Keep

Open the oven door, slacken o the locknut at the base
of the keep, and screw in or out as required until the
required t is obtained. Retighten the locking nut
(Fig.9-15).

36

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

6.7 To Change the Right Hand Oven Door Catch

Remove the screws that secure the latch assembly to
the frame (Fig.9-16). Fit the replacement latch and re­assemble in reverse order.

Check correct operation of door.

6.8 To Remove the Tall Oven Door

Open the oven door. Supporting the door, remove the
2 screws securing the upper hinge and packing to the
cooker front. Remove the door from the lower hinge by
lifting slightly and moving outwards.

Reassemble in reverse order.

6.9 To Replace the Tall Oven Door Outer Panel

Remove the tall oven door (see 6.7). Lay the door face
down on a suitable surface and remove the 2 screws
from bottom edge of door and the 2 screws from the
inside face of the door.

Remove the outer door panel. Remove the door handle
by unscrewing the 2 screws.

Remove the 2 cross-headed screws holding the door
handle xing bracket to the door panel. Fit the door
handle bracket and the door handle to the new panel.

Fit the panel to the door and reassemble in reverse
order.

Fig.9-16

Fig.9-17

6.10 To Replace the Tall Oven Door Magnetic Latch

Remove the control panel (see 4).
Remove the plinth (3 screws) and the central vertical

cover (5 screws). Prize the retaining clip o the magnet
unit. Fit new unit and retaining clip.

Reassemble in reverse order.
Check correct door operation.

6.11 To Change an Oven Door Seal

Open the oven door. The seal is held in place by small
hooks on the rear face. At the corner, pull the seal
diagonally away from the door centre until that hook
is released (Fig.9-17). Proceed to the next hook and
release it in a similar way, and so on. Use force if the
hooks are sti, as the old seal will be discarded.

When tting the new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of
the door, and proceed round the door, snapping in each
hook in turn.

6.12 Oven Door Glass

The glass on the oven doors is not replaceable.

37

10. Circuit Diagram

2

P2

A1

1

v

P095199

r

J

bk

A2

bk

v

r

r

A3

v

bk

A4

r

P1

brbr

r

b

br

bk

r

B1a

bk

b

w

b

J

H

b

b

b

b

b

b

B7

H

b

or

b

G2

b

b

br

ww

B4

B5

B6

B3

v

B1

v

v

r

gr

or

r

gr

w

y

or

bk

bk

br

br

w

br

b

J

v

8 P8

7 P7

6

P6

B2

5 P5

4

3 P3

2

P2

1 P1

P038434

b

bb bbb

P4

bk

v

v

br

y

v

r

w

w

G1

bk

y

br

br

br

br

br v

F1

N/2

N/2

b

v

v

v

v

C

L/1

br

br

b

b

w

b

J

r

K

b

w

y

w

1

2

D1

2

v

D2

1

y

or

P095199

r

P2

P1

br

w

D3

or

f

d

e

c

b
a

1

2

v

b

D4

b

b

H

b

F2

b

A

E

Key

The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.

Code Description

A1 Grill front switch

A2 Grill control

A3 Grill element left-hand side

A4 Grill element right-hand side

B1 Left-hand fan oven thermostat

B1a Left-hand thermostat switch

B2 Left-hand oven control

B3 Left-hand oven base element

B4 Left-hand oven top element

B5 Left-hand oven browning element

B6 Left-hand fan element

B7 Left-hand oven fan

C Clock

Code Description

D1 Right-hand oven thermostat

D2 Right-hand oven control

D3 Right-hand oven fan element

D4 Right-hand oven fan

F1 Ignition switch

F2 Ignition spark generator

G1 Light switch

G2 Oven light

H Thermal cut-out

J Neon

K Cooling fan

Code Colour

b Blue

br Brown

bk Black

or Orange

r Red

v Violet

w White

y Yellow

g/y Green/yellow

gr Grey

38

11. Technical Data

DocAUS.102-0002 - Technical data - 90 Ceramic

This cooker is designed for use on Natural gas, although a

conversion for LP (

LPG X Propane (2.54 kPa)

) gas is packed with the

cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back. The serial number is repeated on the badge below the left-hand oven door opening.

COUNTRY OF DESTINATION: Australia.

Connection & Test Pressures

Gas (Rp ½ at rear right-hand side) Electric

Natural gas 1 kPa
Propane 2.54 kPa

220 -240V 50 Hz

See the appliance badge for test pressures.

Dimensions

Overall height minimum 905 mm maximum 930 mm
Overall width 900 mm
Overall depth 611 mm (to fascia); 668 mm (over handles)
Minimum height above the hotplate 650 mm

Refer to ‘Positioning the Cooker’.

Ratings

Hotplate

Wok burner 55 15.2 MJh

Large burner 41 12.3 MJh
Medium burner 33 6.2 MJh
Small burner 25 3.7 MJh

Bypass
Screw*

Input

Injector

Marking Size Ø Marking Size Ø

internal 88 0.88 mm

-1

external 168 1.68 mm external 98 0.98 mm

-1

-1

-1

165 1.65 mm 12.0 MJh
115 1.15 mm 6.2 MJh

92 0.92 mm 3.3 MJh

Input

15.0 MJh

internal 57 0.57 mm

-1

-1

-1

-1

Injector

89 0.96 mm
67 0.68 mm
48 0.50 mm

Gas burner inputs based on Gross Caloric Value.

* The valves in this cooker are tted with adjustable bypass screws. The cooker is supplied with the bypass screws set for
Natural gas. For LPG conversion the bypass screws must be screwed all the way down.

Oven Efficiency

Main Oven Tall Oven

Natural Gas 1.0 kPa Propane 2.54 kPa

Ovens

Multi-function

(with Rapid Response)

Maximum power output @ 230 V 50 Hz 3.7 kW 2.5 kW
Energy eciency class on a scale of A (more ecient) to G (less ecient) A A
Energy consumption based on standard load 0.95 kWh 0.99 kWh
Usable volume (litres) 69 66
Size Large Large
Time to cook standard load 41 minutes 49 minutes
Surface area of the grid 1400 cm

2

Forced Air

Convection

2

790 cm

Grill 2.3 kW

Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.)

Multi-function oven (with rapid response) variant: 8.6 kW.

39

Notes

40

Notes

41

Clarence Street, Royal Leamington Spa,

Warwickshire, CV31 2AD, England.

Tel: [phone] Fax: [phone]

E-mail: [e-mail]